SyncMaster P50F,P50FN,P63F,P63FN PDP Monitor User Manual
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.
Safety Instructions Ensure that the power plug is plugged into the power outlet firmly and correctly. • Otherwise, this may result in fire. Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Otherwise, this may result in fire. Do not connect multiple appliances to the same power outlet. • Otherwise, this may cause fire due to overheating. Do not disconnect the power cord while using the product.
Safety Instructions Keep heating appliances as far away from the power cord or the product as possible. • Otherwise, this may result in electric shock or fire. Do not install it in a badly ventilated location such as a bookcase or closet. • Otherwise, this may result in fire due to an increase in the internal temperature. When putting the product down, make sure to put it down softly. • Otherwise, this may result in damage to the screen display. Do not place the front of the product on the floor.
Safety Instructions When cleaning the power plug pins or dusting the power outlet, clean it with a dry cloth. • Otherwise, it may result in fire. When cleaning the product, make sure to disconnect the power cord. • Otherwise, it may result in electric shock or fire. When cleaning the product, disconnect the power cord and clean it softly with a dry cloth. • (Do not use chemicals such as wax, benzene, alcohol, thinner, mosquito repellant, lubricant, or cleaner.
Safety Instructions If thunder or lightening is occurring, do not touch the power cord or antenna cable. • Otherwise, this may result in electric shock or fire. Do not try to move the monitor by pulling only the wire or the signal cable. • Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable. Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables.
Safety Instructions If you continually move closer to the product screen, your eyesight may be failing. Take a rest for at least five (5) minutes after using the monitor for one (1) hour. This reduces the weariness of your eyes. Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations. • Otherwise, it may fall and cause personal injury and/or damage the product.
Safety Instructions The batteries (and rechargeable batteries) are not ordinary refuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable batteries for recycling. • The customer can return used or rechargeable batteries to a nearby public recycling center or to a store selling the same type of the battery or rechargeable battery. Do not place the product in a location exposed to direct sunlight or near any heat such as a fire or heater.
Introduction Package Contents Note Please make sure the following items are included with your PDP Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.
Introduction Others (Not available in all locations) (3301-001305) DVI Cable Wall Mount KIT LAN Cable (Applicable to the P50FN / P63FN model only) TV tuner box NetWork Box Semi Stand KIT (Applicable to the P50F / P63F model only) (P50F(N)) Sold separately Note • You can purchase and connect a separate network box or TV tuner box. For information on how to use these, refer to their respective user manuals. • You can only connect one external box.
Introduction SOURCE button [SOURCE] Switches from PC mode to Video mode. Changing the source is only allowed for external devices that are connected to the PDP Display at the time. [PC] → [DVI] → [AV] → [HDMI] → [MagicInfo] Note • The TV menu is available when a TV tuner box is installed. • F model can use MagicInfo menu when mounted Network box. Enter button [ ] Activates a highlighted menu item. MENU button [MENU] Opens the on-screen menu and exits from the menu.
Introduction POWER The power cord plugs into the PDP Display and the wall plug. LAN (LAN Connection Terminal) (Applicable to the P50FN, P63FN model only) USB(USB Connection Terminal) Keyboard / Mouse, Mass Storage Device Compatible. (Applicable to the P50FN, P63FN model only) Note The number of PDP Displays that can be connected to loopout may differ depending on the cables, signal source etc. With cables where there is no degradation or signal source, up to ten PDP Displays can be connected.
Introduction RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port DVI / PC / HDMI IN [DVI/PC/HDMI AUDIO IN] (PC/DVI/HDMI Audio Connection Terminal (Input)) DVI / PC / HDMI IN [HDMI] Connect the HDMI terminal at the back of your PDP Display to the HDMI terminal of your digital output device using a HDMI cable.
Introduction Kensington Lock The Kensington Lock is a device used to physically fix the system when using it in a public place. The locking device has to be purchased separately. The appearance and locking method may differ from the illustration depending on the manufacturer. Refer to the manual provided with the Kensington Lock for proper use. The locking device has to be purchased separately. Note The location of the Kensington Lock may be different depending on its model.
Introduction POWER The power cord plugs into the PDP Display and the wall plug. LAN (LAN Connection Terminal) (Applicable to the P50FN, P63FN model only) USB(USB Connection Terminal) Keyboard / Mouse, Mass Storage Device Compatible. (Applicable to the P50FN, P63FN model only) Note The number of PDP Displays that can be connected to loopout may differ depending on the cables, signal source etc. With cables where there is no degradation or signal source, up to ten PDP Displays can be connected.
Introduction Using a D-Sub Cable (15 pin D-Sub) - PC mode (Analog PC) DVI / PC / HDMI IN [DVI] (PC Video Connection Terminal) Using a DVI Cable (DVI-D to DVI-D) - DVI mode (Digital PC) DC OUT [5V 1.5A] Connect this to the POWER connector of a TV tuner box or network box. AV IN [VIDEO] Connect the [ VIDEO ] terminal of your PDP Display to the video output terminal of the external device using a VIDEO cable.
Introduction POWER OFF Number Buttons DEL button + VOL MUTE TV/DTV MENU INFO COLOR BUTTONS TTX/MIX STILL AUTO S.MODE MDC LOCK SOURCE ENTER/PRE-CH CH/P D.MENU GUIDE RETURN Up-Down Left-Right buttons EXIT SRS MagicInfo P.MODE DUAL/MTS PIP SWAP 1. POWER Turns the product On. 2. Off Turns the product Off. 3. Number Buttons Press to change the channel. 4. DEL The "-" button operates only for DTV. It is used to select MMS (multi-channel) for a DTV.
Introduction 5. + VOL - Adjusts the audio volume. 6. Pauses (mutes) the audio output temporarily. This is displayed on the lower left corner of the screen. The audio resumes if MUTE or - VOL + is pressed in the Mute mode. MUTE 7. TV/DTV 8. Selects the TV and DTV mode directly. MENU Opens the on-screen menu and exits from the menu or closes the adjustment menu. Activates a highlighted menu item. 9. INFO Current picture information is displayed on the upper left corner of the screen. 11.
Introduction 23. RETURN Returns to the previous menu. 24. Up-Down Left-Right buttons Moves from one menu item to another horizontally, vertically or adjusts selected menu values. 25. Exits from the menu screen. EXIT SRS 26. Selects SRS TruSurround XT mode. 27. MagicInfo MagicInfo Quick Launch Button. 28. P.MODE When you press this button, current picture mode is displayed on the lower center of the screen. AV / HDMI / TV : P.
Introduction Mechanical Layout (P50F(N)) Mechanical Layout NETWORK MODEL SIZE
Introduction PDP Display Head NETWORK MODEL SIZE Installation VESA Bracket • When installing VESA, make sure to comply with the international VESA standards. • Purchasing VESA Bracket and Installation Information : Please contact your nearest SAMSUNG Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket. • At least 2 persons are needed in order to move the PDP Display.
Introduction Notice For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length. Wall Bracket Installation • Contact a technician for installing the wall bracket. • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
Introduction 2. A- Captive Screw B- Wall Bracket C- Hinge (Left) D- Hinge (Right) Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct. If the length is too short or long, loosen all or some of the 4 screws on the wall bracket to adjust the length. A3. Length between the two locking holes Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to drill holes deeper than 35 mm.
Introduction 1. Remove the 4 screws on the back of the product. 2. Insert the screw B into the plastic hanger. Notice • Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. • Be careful when installing the product on the bracket as fingers can be caught in the holes. • Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place after installation. 3.
Introduction A- PDP Display B- Wall Bracket C- Wall Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. 1. Fix the product to the wall bracket. 2. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle. Note You can adjust the bracket angle between -2° and 15°. Make sure to use the top center, and not the leftor the right side of the product to adjust the angle.
Introduction Mechanical Layout (P63F(N)) Mechanical Layout NETWORK MODEL SIZE PDP Display Head NETWORK MODEL SIZE Wall Bracket Installation • Contact a technician for installing the wall bracket. • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
Introduction Wall Bracket(1) Hinge(Left 1, Right Plastic Screw 1) Hanger (A)(11) (4) Screw (B)(4) Anchor (11) Wall Bracket Assembly Note There are two hinges(left and right). Use the correct one. 1. Insert and tighten the Captive Screw in the direction of the arrow. When done, mount the wall bracket on the wall. There are two hinges(left and right). Use the correct one. 2.
Introduction A3. Length between the two locking holes Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each of the brackets and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws A. To mount the product on the wall bracket The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same) 1.
Introduction • Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place after installation. 3. Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product. 4. Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket.
Introduction Note You can adjust the bracket angle between -2° and 15°. Make sure to use the top center, and not the leftor the right side of the product to adjust the angle.
Connections Connecting a Computer Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un-wiring the earth lead, make sure to disconnect the AC power in advance. Note AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the PDP Display.
Connections Connect the audio cable for your PDP Display to the audio port on the back of your computer. Note • Turn on both your computer and the PDP Display. • The DVI cable is optional. • Contact a local SAMSUNG Electronics Service Center to buy optional items. Connecting to Other devices Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power.
Connections Note The PDP Display has AV connection terminals to connect AV input devices like DVDs, VCRs or Camcorders. You may enjoy AV signals as long as the PDP Display is turned on. Connecting to a Camcorder 1. Locate the AV output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the AV AUDIO IN [L-AUDIO-R] on the PDP Display. 2.
Connections Connecting Using a DVI to HDMI Cable Note • Connect the DVI output terminal of a digital output device to the HDMI IN terminal of the PDP Display using a DVI to HDMI cable. • Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio output terminals of the digital output device, and connect the opposite jack to the HDMI / PC / DVI AUDIO IN terminal of the PDP Display.
Connections Note Please refer to below image which contains explanations based on 50 inch model. (Only the terminal location is different between 50 inch and 63 inch models) Note Connect the LAN cable. (Applicable to the P50FN / P63FN model only) Connecting a USB device Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power.
Connections (Applicable to the P50FN / P63FN model only)
Using the Software Installation MagicInfo Pro Installation 1. Insert CD into the CD-ROM drive. 2. Click the MagicInfo Pro installation file. 3. When the Install Shield Wizard window appears, click "Next." 4. Select "I agree to the terms of the license agreement" to accept the terms of use. 5. You are required to log in to the MagicInfo Pro Server program. Please enter the password to login. The password cannot be changed when you are logged in.
Using the Software 6. Choose a folder to install the MagicInfo Pro program. 7. Click "Install.
Using the Software 8. The "Installation Status" window appears. 9. It is recommended restarting the system for the normal operation of the MagicInfo Pro Server program. Click "Finish".
Using the Software 10. When the installation is complete, the MagicInfo Pro executable icon appears on your desktop. 11. Double-click the icon to start the program. System Requirements CPU RAM Ethernet OS Application Minimum P1.8 256M 100M/1G Recommended P3.
Introduction A Multiple Display Control (MDC) is an application allowing various displays to be easily and simultaneously operated on a PC. RS-232C, a standard of serial communication, is used for the communication between a PC and a display. Therefore, a serial cable should be connected between the serial port on a PC and the serial port on a display. Main Screen Click Start > Program > Samsung > MDC System to start the program. Select a set to see the volume of the selected set within the slider.
Main Icons Select Button Remocon Info Grid Safety Lock Display Selection Port Selection Control Tools 1. Use the main icons to switch into each screen. 2. Allows you to enable or disable the remote control signal receiving function of the display unit. 3. Set the Safety Lock function. When setting the Lock function, you can only operate power and lock buttons on the remote control and set. 4. The setting for the PC Serial Port can change. The original value is COM1. 5.
1. The Multiple Display Control is originally set to COM1. 2. If any port other than COM1 is used, COM1 through COM4 can be selected in the Port Selection Menu. 3. If the exact port name that is connected to the PDP Display using a serial cable is not selected, communication will be unavailable. 4. The selected port is stored in the program and used for the next program as well. Power Control 1. Click Power Control of the main icons and the Power Control screen appears.
Info Grid shows some basic information necessary to Power Control. 1) (Power Status) 2) Input 3) Image Size 4) On Timer 5) Off Timer 2. Use the Select All button or Check Box to choose a display to control. Power Control allows controlling some of the functions of the selected display.
- Turns the power of the selected display On/Off. 2) Volume - Controls the volume level of the selected display. It receives the volume value of the selected display from the sets and displays it in the slider. (When you cancel the selection or choose Select All, the value returns to the default value 10) 3) (Mute On/Off) - Turns on/off the Mute function of the selected display. When selecting one set at a time, turn on the Mute function for the selected set.
Info Grid shows some basic information necessary to Input Source Control. 1) PC - Changes the Input Source of the selected display to PC. 2) BNC - Changes the Input Source of the selected display to BNC. 3) DVI - Changes the Input Source of the selected display to DVI. 4) TV - Changes the Input Source of the selected display to TV. 5) DTV - Changes the Input Source of the selected display to DTV. 6) AV - Changes the Input Source of the selected display to AV.
Info Grid shows some basic information necessary to Image Size Control. 1) ( Power Status) - Shows the power status of the current display. 2) Image Size - Shows the current Image Size of the display in use. 3) Input - Shows the current Input Source of the display in use. 4) Info Grid displays only the displays whose Input Source is PC, BNC, DVI. 5) PC Source - When you click Image Size, the PC Source tab first appear. - The Image Size Control button controls Image Size available for PC, BNC, DVI.
Info Grid shows some basic information necessary to Image Size Control. 1) Click the Video Source tab to adjust Image Size for TV, AV, S-Video, Component, DVI(HDCP), HDMI, DTV. Click Select All or use Check Box to select a display to control. 2) Info Grid displays only the display having TV, AV, S-Video, Component or DVI(HDCP) as input source. 3) Switch Image Size of the selected display randomly.
Info Grid shows some basic information necessary to Time Control. 1) Current Time - Set the current time for the selected display (PC Time). - To change the current time, first change the PC Time. 2) On Time Setup - Set the Hour, Minute, AM/PM of On Time Setup, Status, Source, Volume of the selected display. 3) Off Time Setup - Set the Hour, Minute, and AM/PM, Status for Off Time Setup of the selected display. 4) Shows the On Time settings. 5) Shows the Off Time settings.
Info Grid shows some basic information necessary to PIP Size Control. 1) PIP Size - Shows the current PIP Size of the display in use. 2) OFF - Turns off the PIP of the selected display. 3) Large - Turns on the PIP of the selected display and changes the size to Large. 4) Small - Turns on the PIP of the selected display and changes the size to Small. 5) Double 1 - Turns on the PIP of the selected display and changes the size to Double 1.
Info Grid shows some basic information necessary to PIP Source Control. 1) PIP Source - PIP Source can be controlled with turning on the PDP Display power. 2) PC - Changes the source of the PIP of the selected display to PC. 3) BNC - Changes the source of the PIP of the selected display to BNC. 4) DVI - Changes the source of the PIP of the selected display to DVI. 5) AV - Changes the source of the PIP of the selected display to AV.
Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide.When selected, each function fetches the value for the set and displays it on the slide bar. When "Select All" is chosen, the default value is displayed. Changing a value in this screen will automatically change the mode to "CUSTOM." 1) Picture - Available only for TV, AV, S-Video, Component, HDMI, DTV.
1. Click Settings of the main icons and the Settings Control screen appears. Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide. When selected, each function fetches the value for the set and displays it on the slide bar. When "Select All" is chosen, the default value is displayed. Changing a value in this screen will automatically change the mode to "CUSTOM.
Audio 1. Click Settings of the main icons and the Settings Control screen appears. Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide. When selected, each function fetches the value for the set and displays it on the slide bar. When "Select All" is chosen, the default value is displayed. Changing a value in this screen will automatically change the mode to "CUSTOM.
Info Grid shows some basic information necessary to Settings Control. 1) Image Lock - Available only for PC, BNC. 2) Coarse - Adjusts Coarse of the selected display. 3) Fine - Adjusts Fine of the selected display. 4) Position - Adjusts Position of the selected display. 5) Auto Adjustment - Self-Adjust to the incoming PC signal. The Input source of MagicInfo works only on MagicInfo model. The Input source of TV works only on TV model.
An "Info Grid" showing several basic data items appears. 1) Maintenance - Allows the Maintenance Control function for all input sources. 2) Auto Lamp Control - Automatically adjusts the backlight of the selected display at a specified time. The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control. 3) Manual Lamp Control - Allows you to adjust the backlight of the selected display regardless of the time.
1) Safety Screen - Eliminates the afterimages that can result when the selected display stays in Pause mode for an extended period of time. You can set the repeat cycle timer by selecting the "Interval" by hour and "Second" by second. It can be set to Scroll, Pixel, Bar and Eraser by Screen Type. The Input source of MagicInfo works only on MagicInfo model. The Input source of TV works only on TV model.
1) Video Wall - A Video Wall is a set of video screens that are connected together, so that each screen shows a part of the whole picture or so that the same picture is repeated on each screen. 2) Video Wall (Screen divider) - The screen can be divided into. You can select a number of screens with a different layout when dividing. z Select a mode from Screen divider. z Select a display from Display Selection. z The place will be set up by pressing a number in the selected mode.
- Check the displays to see if any of the other displays connected have the same ID. If more than one displays have the same ID, those displays are not properly detected by the program due to data conflict. - Check if the Display Set ID is a number between 0 and 25. (Adjust using the Display menu) Note : A Display Set ID must be a value between 0 and 25 . 2. The display you wish to control does not appear on the other Control Info Grids - Check to see if the display power is ON.
Adjusting the PDP Display Input Available Modes • PC / DVI • AV • HDMI • MagicInfo • TV Note • The TV menu is available when a TV tuner box is installed. • F model can use MagicInfo menu when mounted Network box. Source List MENU → ENTER → [Input] → ENTER → [Source List] → , → ENTER Use to select PC, DVI or other external input sources connected to the PDP Display. Use to select the screen of your choice. 1. PC 2. DVI 3. AV 4.
Adjusting the PDP Display Note • The direct button on the remote control is the 'SOURCE' button. Edit Name MENU → ENTER → [Input] → → ENTER → [Edit Name] → , → ENTER Name the input device connected to the input jacks to make your input source selection easier. VCR / DVD / Cable STB / HD STB / Satellite STB / AV Receiver / DVD Receiver / Game / Camcorder / DVD Combo / DHR / PC Note • When connecting a PC to the HDMI or DVI terminal, set Edit Name to PC. • In other cases, set Edit Name to AV.
Adjusting the PDP Display • F model can use MagicInfo menu when mounted Network box. MagicBright MENU → → ENTER → [Picture] → ENTER → [MagicBright] → , → ENTER MagicBright is a feature providing the optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Entertain, Internet, Text and Custom. Each mode has its own pre-configured brightness value.
Adjusting the PDP Display Adjusts the Contrast. Brightness MENU → → ENTER → [Picture] → ness] → , → ENTER → ENTER → [Custom] → → ENTER → [Bright- Adjusts the Brightness. Sharpness MENU → → ENTER → [Picture] → [Sharpness] → , → ENTER → ENTER → [Custom] → → ENTER→ → Adjusts the Sharpness. Color Tone MENU → → ENTER → [Picture] → → →ENTER → [Color Tone] → , → ENTER The color tones can be changed. 1. Off 2. Cool 3. Normal 4. Warm 5.
Adjusting the PDP Display MENU → → ENTER → [Picture] → → → → ENTER → [Color Control] Note If you adjust the picture by using the Color Control function, Color Tone will turn to the Custom mode.
Adjusting the PDP Display Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. Fine MENU → → ENTER → [Picture] → ENTER → [Fine] → , → ENTER → → → → ENTER → [Image Lock] → → Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed).
Adjusting the PDP Display Signal Balance MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal Balance] → ENTER → [Signal Balance] → , → ENTER Selects either On or Off with the signal control. Signal Control MENU → → ENTER → [Picture] → → → ENTER → [Signal Control] 1. → → → → → → ENTER → [Signal Balance] R-Gain MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal Balance] → → ENTER → [Signal Control] → ENTER → [R-Gain] → , → ENTER 2.
Adjusting the PDP Display 6. B-Offset MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal Balance] → → ENTER → [Signal Control] → → → → → → ENTER → [BOffset] → , → ENTER Size MENU → → ENTER → [Picture] → → ENTER → → → → → → → ENTER → [Size] → The Size can be switched. 1. 16:9 2. 4:3 Picture [ AV / HDMI / DVI / TV Mode] Available Modes • PC • AV • HDMI / DVI • MagicInfo • TV Note • The TV menu is available when a TV tuner box is installed.
Adjusting the PDP Display The PDP Display has four automatic picture settings ("Dynamic", "Standard", "Movie" and "Custom") that are preset at the factory. Dynamic, Standard, Movie, or Custom can be activated. 1. Dynamic 2. Standard 3. Movie 4. Custom Note The direct button on the remote control is the 'P.MODE' button. Custom By using the on-screen menus, the contrast and brightness can be changed to your personal preference.
Adjusting the PDP Display Adjusts the picture Sharpness. Color MENU → → ENTER → [Picture] → [Color] → , → ENTER → ENTER → [Custom] → → → → ENTER → Adjusts the picture Color. Tint MENU → → ENTER → [Picture] → → [Tint] → , → ENTER → ENTER → [Custom] → → → → → ENTER Adds a natural tone to the display. Note Tint function can be available just in NTSC system. Color Tone MENU → → ENTER → [Picture] → → → ENTER → [Color Tone] → , → ENTER The color tones can be changed.
Adjusting the PDP Display Color Temp. MENU → → ENTER → [Picture] → → → → ENTER → [Color Temp.] → , → ENTER Color temp is a measure of the 'warmth' of the image colors. Note This function is only enabled if the Color Tone is set to Off. Size MENU → → ENTER → [Picture] → → → → → ENTER → [Size] → , → ENTER The Size can be switched. 1. 16:9 - Sets the picture to 16:9 wide mode. 2. Zoom 1 - Magnifies the size of the picture on the screen. 3.
Adjusting the PDP Display Turns the Digital Noise Reduction feature Off/On. The Digital Noise Reduction feature allows you to enjoy clearer and crisper images. 1. Off 2. On Film Mode MENU → → ENTER → [Picture] → , → ENTER → → → → → → ENTER → [Film Mode ] → The Film Mode feature offers you a theater-quality viewing experience. (In HDMI mode, this function can be available when the input signal is interlaced scan; it cannot be available with progressive scan signal.) 1. Off 2.
Adjusting the PDP Display The PDP Display has a built-in high fidelity stereo amplifier. 1. Standard Selects Standard for the standard factory settings. 2. Music Selects Music when watching music videos or concerts. 3. Movie Selects Movie when viewing movies. 4. Speech Selects Speech when watching a show that is mostly dialogue (i.e., news). 5. Custom Selects Custom if you want to adjust the settings according to your personal preferences.
Adjusting the PDP Display Emphasizes high frequency audio. Balance MENU → → → ENTER → [Sound] → → ENTER → [Custom ]→ → →ENTER→ [Balance] → , → ENTER Allows you to Adjusts the sound balance between the left and right speakers. Auto Volume MENU → → → ENTER → [Sound] → → → ENTER → [Auto Volume] → , → ENTER Reduces the difference in volume control between broadcasters. 1. Off 2.
Adjusting the PDP Display Setup Available Modes • PC / DVI • AV • HDMI • MagicInfo • TV Note • The TV menu is available when a TV tuner box is installed. • F model can use MagicInfo menu when mounted Network box. Language MENU → → → → ENTER → [Setup] → ENTER → [Language ] → , → ENTER You can choose one of 11 languages. Note The language chosen affects only the language of the OSD. It has no effect on any software running on the computer.
Adjusting the PDP Display Current Time Setting. Sleep Timer MENU → Timer] → → → → ENTER → [Setup] → , → ENTER → ENTER → [Time ] → → ENTER→ [Sleep Turns the PDP Display off automatically at certain times. 1. Off 2. 30 3. 60 4. 90 5. 120 6. 150 7. 180 On Timer MENU → → → → ENTER → [Setup] → [On Timer] → , / , → ENTER → ENTER → [Time ] → → → ENTER→ Turns the PDP Display on automatically at a preset time.
Adjusting the PDP Display Off Timer MENU → → → → ENTER → [Setup] → → [Off Timer] → , / , → ENTER → ENTER → [Time ] → → → → ENTER Turns the PDP Display off automatically at a preset time. Menu Transparency MENU → → → → ENTER → [Setup] → → → ENTER → ENTER → [Menu Transparency] → , Change the transparency of the background of the OSD. 1. High 2. Medium 3. Low 4. Opaque Safety Lock PIN MENU → → → → ENTER → [Setup] → → → [0∼9] → [0∼9] → [0∼9] → [0∼9] The password can be changed.
Adjusting the PDP Display Energy Saving MENU → → → → ENTER → [Setup] → → → → , → ENTER → ENTER → [Energy Saving] → This feature adjusts the power consumption of the unit in order to save energy. 1. Off 2. On Note If you want to reduce the standby power consumption, set Energy Saving to On. However, when Energy Saving is On, you cannot use the remote Power On function of the MDC and the WOL (Wake On LAN) function of MagicInfo.
Adjusting the PDP Display Note When Video Wall is running, the Auto Adjustment, Image Lock, and Size functions are not available. Video Wall does not operate in MagicInfo mode. Video Wall MENU → → → → ENTER → [Setup] → → → → Wall ]→ ENTER → [Video Wall ] → , → ENTER → → → ENTER → [Video Turns Off/On the Video Wall function of the selected display Off/On. 1. Off 2.
Adjusting the PDP Display Sets how many parts the screen should be divided horizontally. Five adjustment levels: 1, 2, 3, 4, and 5. Vertical MENU → → → → ENTER → [Setup] → → → → → Wall ]→ → → → ENTER → [Vertical] → , → ENTER → → ENTER → [Video → → ENTER → [Video Sets how many parts the screen should be divided vertically. Five adjustment levels: 1, 2, 3, 4, and 5.
Adjusting the PDP Display • The Safety Screen function scrolls the screen for the specified period of time. • This function is not available when the power is turned off.
Adjusting the PDP Display Sets how many pixels the screen moves vertically. Five adjustment levels: 1, 2, 3, 4, and 5. Time MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → ENTER → [Pixel Shift] → → → → ENTER → [Time] → , → ENTER Set the time interval for performing the horizontal or vertical movement, respectively.
Adjusting the PDP Display You can change the Safety Screen Type. 1. Scroll 2. Bar 3. Eraser 4. All White 5. Pattern Period MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → → ENTER → [Timer] → → → ENTER → [Period] → , → ENTER Use this function to set the execution period for each mode set in the timer.
Adjusting the PDP Display Scroll MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → → → ENTER → [Scroll] This function prevents after-images on the screen by moving all the pixels on the PDP according to a pattern. Use this function when there are remaining after-images or symbols on the screen, especially when you displayed a still image on the screen for a long time.
Adjusting the PDP Display This function prevents after-images on the screen by changing the color of pixels to white. Use this function when there are remaining after-images or symbols on the screen, especially when you displayed a still image on the screen for a long time. Pattern MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → → → → → → →ENTER → [Pattern] This function prevents after-images on the screen by moving a diagonal pattern stored in the panel repeatedly.
Adjusting the PDP Display 3. 1280 X 768 4. 1360 x 768 5. 1366 X 768 6. 1920 X 1080 Note Selecting the menu is only allowed when the graphics resolution is set to 1024 x 768 @ 60Hz, 1280 x 768 @ 60Hz, 1360 x 768@ 60Hz, 1366 x768 @ 60Hz or 1920 x 1080 @ 60Hz. Power On Adjustment MENU → → → → ENTER → [Setup] → → → → → [Power On Adjustment ] → , → ENTER → → → → → → ENTER Adjusts the Power On time for the screen. Caution: Set the Power On time to be longer to avoid overvoltage.
Adjusting the PDP Display MENU → → → → ENTER → [Setup] → → → → → ENTER → [Reset ] → → → → → → → MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Reset ]→ ENTER → [Image Reset ] → , → ENTER → → → → → → → → Image Reset Note Available in PC mode only Note The Reset function is not available when Video Wall is On.
Adjusting the PDP Display • ID Input Use to select the transmitter functions of the individual SET. Only a SET where the ID corresponds to the transmitter setting becomes activated. MagicInfo Available Modes • PC / DVI • AV • HDMI • MagicInfo • TV Note • The operating system for this set only supports English so the other languages might be corrupted on the screen. • For MagicInfo, a remote control is available for MagicInfo. However, it is recommended using a separate USB keyboard.
Adjusting the PDP Display • For pivoted PDP Displays, ticker transparency is not supported. • For pivoted PDP Displays, a screen resolution of up to 720*480(SD) is supported for movies. • For drive D:, EWF is not applied. • When the contents of Setup have been changed when EWF is in the Enable state, to save the changes in the disk, you must Commit them. • By selecting Disable, Enable or Commit, the system is restarted. Magicinfo 1. Select Magicinfo in the Source List menu. 2.
Adjusting the PDP Display 4. Connect your keyboard and mouse and press the “ALT + F12” keys on your keyboard. 5. The Windows Desktop is displayed and the Magicinfo pro icon (the image will be inserted) appears. Move the cursor over the icon. Note If the Magicinfo icon is not displayed on the notification area, double click the Magicinfo icon on the window desktop. The icon will appear. 6.
Adjusting the PDP Display 7. The Player screen of Magicinfo pro is displayed. Note To finish the MagicInfo, press ALT + F12. Photo The JPEG, BMP file format are supported.
Adjusting the PDP Display Auto Automatically fits the image to the window. Original Shows the properties of the original file. Slide Show Displays the properties of the original file as they are.
Adjusting the PDP Display Interval Controls the time intervals between image files for a slide show. (5 Sec, 10 Sec, 20 Sec, 30 Sec, 60 Sec) Rotation Displays an image file by turning it clockwise by 90 degrees.
Adjusting the PDP Display Zoom Displays a reduced picture. Close Closes the image control Menu.
Adjusting the PDP Display Music The MP3 file format is supported. Movie The MPEG1, WMV file format are supported. Play Plays a movie file.
Adjusting the PDP Display Full Size Plays a movie file in full screen. OFFICE / HTML PPT(Power Point), DOC(MS Word), XLS(MS Excel), PDF, HTML, HTM files are displayed. Note • Install the proper viewer(freeware) program to see the MS Office(Word, Excel, Power Point) or PDF doucuments.
Adjusting the PDP Display Internet Connects to the Internet Setup Sets various functions in MagicInfo mode. A password must be entered to access Setup mode. Schedule View Displays a schedule.
Adjusting the PDP Display TCP/IP Changes the TCP/IP settings. Connection Modifies the network settings.
Adjusting the PDP Display Password The password can be changed. • The password should be between 6 and 12 characters in numeric format. (You should enter a password between 6 and 12 characters in numeric format) • If you enter the wrong password three times, the setup configuration is reset and a warning message appears from the server. • If you forget the password, enter Info, 8, 2 and 4 on the remote control to initialize the password. This will reset the previous settings of Setup mode.
Adjusting the PDP Display Play Option You can set the repeat play and screen settings. Repeat : Determines the repeat option for playing movies and music. • None - Select No Repeat to play a movie or tune in the list only once. • File Repeat - Select Repeat File to play a movie or tune in the list repeatedly. • List Repeat - Select Repeat List to play movies or tunes in the list in sequence repeatedly. Rotation - Sets the picture orientation.
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the PDP Display. 2. Unplug the video cable from the back of the computer. 3. Turn on the PDP Display.
Troubleshooting • Do not use benzene, thinner or other flammable substances, or a wet cloth. • We recommend that a SAMSUNG cleansing agent is used to prevent damage to the screen. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly. • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.) • The user will be required to pay costs and related expenses for repairing damages caused.
Troubleshooting A: Check if the signal cable between the computer and the PDP Display is securely connected. (Refer to Connecting a Computer) Problems related to the Screen Note Problems related to the PDP Display screen and their solutions are listed. Q: The screen is blank and the power indicator is off. A: Ensure that the power cord is firmly connected and the PDP Display is on. (Refer to the Connecting a Computer) Q: "Check Signal Cable" message.
Troubleshooting Q: The screen color is inconsistent. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The color image is distorted by dark shadows. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The color white is poor. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The Power Indicator blinks. A: The PDP Display is currently saving the changes made in the settings to the OSD memory.
Troubleshooting A: Check the polarities (+/-) of the batteries. A: Check if the batteries are empty. A: Check if the power is on. A: Check if the power cord is securely connected. A: Check if a special fluorescent or neon lamp is on in the vicinity. Problems related to MagicInfo Note Making a Bootable USB Flash Disk. Q: Making a Bootable USB Flash Disk A: 1) You can turn a common 512-MB or bigger USB storage media into a bootable disk using a USB bootable disk creation tool.
Troubleshooting Set the resolution in the Control Panel → Appearance and Themes → Display → Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual). A: Windows ME/2000: Set the resolution at the Control Panel → Display → Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual).
Specifications General General Model Name SyncMaster P50F(N) SyncMaster P63F(N) PDP Panel Size Display area Pixel Pitch SyncMaster P50F(N) 50 " Diagonal (127 cm) SyncMaster P63F(N) 63 " Diagonal (159 cm) SyncMaster P50F(N) 1105.92 mm (H) X 622.08 mm (V) SyncMaster P63F(N) 1393.92mm(H) X 784.08mm(V) SyncMaster P50F(N) 0.576mm(H) x 0.576mm(V) SyncMaster P63F(N) 0.726mm(H) x 0.726mm(V) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 85 Hz Display Color 16.
Specifications Power Supply AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz Signal Cable 15pin-to-15pin D-sub cable, Detachable DVI-D to DVI-D connector, Detachable (Sold separately) Dimensions (W x H x D) / Weight SyncMaster P50F(N) 1204.6x 724.1 x 97.1 mm (47.4 x 28.5 x 3.8 inch) (Without Stand) 1204.6 x 773.2 x 362.4 mm (47.4 x 30.4 x 14.3 inch) (With Stand) / 37.4 kg (82.5 lbs) SyncMaster P63F(N) 1502.7x 893.1 x 99.0 mm (59.2 x 35.2 x 3.9 inch) (Without Stand)/ 65.0 kg (143.
Specifications Dot Acceptable For example, the number of PDP sub pixels contained in this product are 6,220,800. Note Design and specifications are subject to change without prior notice. Class B Equipment (Information Communication equipment for residential use) This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.
Specifications CPU Recommended RAM P3.0 GHz 512 M Ethernet OS Application 100 M / 1 Windows WMP 9 or G XP later PowerSaver This PDP Display has a built-in power management system called PowerSaver. This system saves energy by switching your PDP Display to low-power mode when it has not been used for a certain amount of time. The PDP Display automatically returns to normal operation when you press a key on the keyboard.
Specifications Display Mode Horizontal Frequency (kHz) Vertical Fre- Pixel Clock quency (Hz) (MHz) Sync Polarity (H/V) VESA, 640 x 480 37.861 72.809 31.500 -/- VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 800 x 600 35.156 56.250 36.000 +/+ VESA, 800 x 600 37.879 60.317 40.000 +/+ VESA, 800 x 600 48.077 72.188 50.000 +/+ VESA, 800 x 600 46.875 75.000 49.500 +/+ VESA, 848 x 480 31.020 60.000 33.750 +/+ VESA, 1024 x 768 48.363 60.004 65.
Information For Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for PDP. • Resolution: 1920 x 1080 @ 60Hz • Vertical frequency (refresh rate): 60 Hz PDP panels manufactured by using advanced semiconductor technology with a precision of 1ppm (one millionth) and above is used for this product.
Information Power Off, Screen Saver, or Power Save Mode • Turn the power off for 4 hours after 20 hours in use • Turn the power off for 2 hours after 12 hours in use • Set the Monitor to power off with the PC Display Properties Power Scheme. • Use a Screen saver if possible - Screen saver in one color or a moving image is recommended. Change the Color Information periodically Note Use Two different colors Rotate the Color Information with 2 different colors every 30 minutes.
Information • Use Bright colors with little difference in luminance. - Cycle : Change the characters color and background color every 30 minutes • Every 30 minutes, change the characters with movement. • All area display Moving image together with Logo periodically. - Cycle: Display moving image together with Logo for 60 seconds after 4 hours in use.
Information - Select method • • Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Pixel • Time Interval : 1 ~ 10 hours ( Recommend : 1 ) • Time Period : 10 ~ 50 second ( Recommend : 50 ) Apply the Screen Bar function - Symptom: Horizontal / Vertical Bar with Black Color move up and down.
Information • Time Interval : 1 ~ 10 hours ( Recommend : 1 ) • Time Period : 10 ~ 50 second ( Recommend : 50 ) Note ( Please check CD's User Guide at "OSD Function", some model's will not available )
Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG(726-7864) http://www.samsung.com/us CANADA 1-800-SAMSUNG(726-7864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG (726-7864) http://www.samsung.com/mx Latin America ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 0800-124-421 http://www.samsung.
Appendix Europe BELGIUM 02 201 2418 http://www.samsung.com/be CZECH REPUBLIC 800 (800-726786) SAMSUNG http://www.samsung.com/cz DENMARK 8 - SAMSUNG (7267864) http://www.samsung.com/dk EIRE 0818 717 100 http://www.samsung.com/ie FINLAND 30 - 6227 515 http://www.samsung.com/fi FRANCE 3260 'dites' SAMSUNG (€ http://www.samsung.com/fr 0,15/Min) 0825 08 65 65 (€ 0.15/Min) GERMANY 01805 SAMSUNG http://www.samsung.de (7267864, € 0.14/Min) HUNGARY 06-80-SAMSUNG (726-7864) http://www.samsung.
Appendix Asia Pacific AUSTRALIA 1300 362 603 http://www.samsung.com/au CHINA 800-810-5858 http://www.samsung.com/cn 400-810-5858 010-6475 1880 INDIA HONG KONG:3698 - 4698 http://www.samsung.com/hk 3030 8282 http://www.samsung.com/in 1800 110011 1-800-3000-8282 INDONESIA 0800-112-8888 http://www.samsung.com/id JAPAN 0120-327-527 http://www.samsung.com/jp MALAYSIA 1800-88-9999 http://www.samsung.com/my NEW ZEALAND 0800 SAMSUNG(0800 726 http://www.samsung.
Appendix Interlace and Non-Interlace Methods Showing the horizontal lines of the screen from the top to the bottom sequentially is called the Non-Interlace method while showing odd lines and then even lines in turn is called the Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs.
Appendix Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Samsung is the registered trademark of Samsung Electronics Co., Ltd.
