NETWORK CAMERA User Manual PNV-A9081R/PND-A9081RV PND-A9081RF/PNO-A9081R PNB-A9001
Network Camera User Manual Copyright ©2019 Hanwha Techwin Co., Ltd. All rights reserved. Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
overview IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth. (Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.) 7.
overview Class construction An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection. Battery Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. The battery cannot be replaced. Disconnection Device Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location. When used outside of the U.S.
CONTENTS OVERVIEW 6 8 Important Safety Instructions Recommended PC Specifications Recommended Micro SD/SDHC/SDXC Memory Card Specifications NAS recommended specs Optional Accessories for Installation OUTDOOR VANDAL DOME CAMERA 9 9 10 What’s Included At a Glance Installation INDOOR DOME CAMERA 17 17 18 What’s Included At a Glance Installation 24 24 25 What’s Included At a Glance Installation 31 31 32 What’s Included At a Glance Installation 3 9 17 FLUSH MOUNT DOME CAMERA 24 OUTDOOR BULLET CA
overview RECOMMENDED PC SPECIFICATIONS NAS RECOMMENDED SPECS •• CPU : Intel(R) Core(TM) i7 3.4 GHz or higher •• RAM : 8G or higher •• Supported OS : MS Windows 8.1, 10, Mac OS X 10.12, 10.13, 10.14 •• Recommended browser: Google Chrome Supported browsers: MS Explorer, MS Edge, Mozilla Firefox (Window 64bit only), Apple Safari (Mac OSX only) •• Recommended capacity : 200GB or higher is recommended. •• For this camera, you are recommended to use a NAS with the following manufacturer’s specs.
Outdoor Vandal Dome Camera Indoor Dome Camera PNV-A9081R Flush Mount Dome Camera PND-A9081RV PND-A9081RF ●● OVERVIEW 9 17 Outdoor Bullet Camera PNO-A9081R 31 24 Box Camera PNB-A9001 38 English _7
overview OPTIONAL ACCESSORIES FOR INSTALLATION Model name Hanging Mount PNV-A9081R SBP-187HMW of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power You can purchase appropriate optional accessories available.
WHAT’S INCLUDED As for each sales country, accessories are not the same. of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power n Video out connection terminal k DC 12 V power ●● OUTDOOR VANDAL DOME CAMERA of the Be ware CAUTION: and Polarity Rated Voltageconnection.
outdoor vandal dome camera INSTALLATION 2. Take off the cushion protecting the camera lens. camera is waterproof and in compliance with the IP67 / IP6K9K spec, but the jack connected to the external cable is not. JJ `` This You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Removing a Micro SD Memory Card Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot. Installation (mount plate) [Directly installing on wall/ceiling] 1-1. Attach the installation template on the desired surface and drill holes for screws and cables. ●● OUTDOOR VANDAL DOME CAMERA removing the Micro SD memory card, in , set the device to and press the [Apply] button and turn JJ `` Before the camera off.
outdoor vandal dome camera [Installing using pipe] 2-1. Attach the installation template and drill holes for screws and cables. 2-2. Separate the pipe cover of the mount plate by pressing its sides. 2-3. Place the pipe on the mount plate. 2-4. Fix the mount plate using appropriate screws. 2-5. Pull out necessary cables among LAN/power/audio & alarm cables through the pipe. Installation (camera case) JJ `` Use a cable bush compliant with the LAN cable to be connected.
1-4. Mount the bush to the camera case. 2-3. Mount the bush to the camera case. ●● OUTDOOR VANDAL DOME CAMERA [Installing the LAN cable] (IP66) 2-1. Pull off the extruded part of the 1-hole bush provided. 2-2. Use the cap installer to pass through the RJ45 cable. [Installing audio & alarm cables] 3-1. Mount the bush of the provided audio & alarm cables to the camera case.
outdoor vandal dome camera Installing the camera module 4. Join the mount plate with the camera case. 1. Connect the LAN/power/audio & alarm cables to the camera module terminal. 2. Attach the camera module to the case. JJ `` A magnet is embedded at the bottom of the module 2x `` Take caution not to allow any foreign objects between the attaching surfaces. x4 TR20 3. Adjust the lens to the desired direction with reference to “Adjusting the monitoring direction for the camera” section.
Assembling the dome cover [Using Weather cap] 1. Remove the screws from the dome cover. [Directly installing on wall/ceiling] 1. Assemble the dome cover. JJ `` Make sure to firmly tighten the fastening screws so that there is no water damage issue. 4x ●● OUTDOOR VANDAL DOME CAMERA 2x TR20 x4 TR20 2. Assemble the dome cover. 3. Mount the weather cap to the dome cover and fasten the screws. JJ `` Make sure to firmly tighten the fastening screws so that there is no water damage issue.
outdoor vandal dome camera Outdoor installation When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside. 1. Connect the power, I/O, and LAN cables. 2. Wrap the black cable jacket (Area A) and the cable connection area with waterproof (butyl rubber) tape so that more than half of the butyl rubber tape is overlapped.
indoor dome camera WHAT’S INCLUDED AT A GLANCE As for each sales country, accessories are not the same. a Pipe-cover Mount-plate c ●● INDOOR DOME CAMERA b Camera-case d Camera-module e Dome-cover of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection.
indoor dome camera INSTALLATION 2. Take off the cushion protecting the camera lens. camera is waterproof and in compliance with the IP52 spec, but the jack connected to the external cable is not. You are JJ `` This recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Removing a Micro SD Memory Card Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot. Installation (mount plate) [Directly installing on wall/ceiling] 1-1. Attach the installation template on the desired surface and drill holes for screws and cables. ●● INDOOR DOME CAMERA removing the Micro SD memory card, in , set the device to and press the [Apply] button and turn JJ `` Before the camera off.
indoor dome camera [Installing using pipe] 2-1. Attach the installation template and drill holes for screws and cables. 2-2. Separate the pipe cover of the mount plate by pressing its sides. 2-3. Place the pipe on the mount plate. 2-4. Fix the mount plate using appropriate screws. 2-5. Pull out necessary cables among LAN/power/audio & alarm cables through the pipe. Installation (camera case) JJ `` Use a cable bush compliant with the LAN cable to be connected.
1-4. Mount the bush to the camera case. 2-3. Mount the bush to the camera case. ●● INDOOR DOME CAMERA [Installing the LAN cable] 2-1. Pull off the extruded part of the 1-hole bush provided. 2-2. Use the cap installer to pass through the RJ45 cable.
indoor dome camera Installing the camera module [Installing audio & alarm cables] 3-1. Mount the bush of the provided audio & alarm cables to the camera case. 1. Connect the LAN/power/audio & alarm cables to the camera module terminal. 2. Attach the camera module to the case. JJ `` A magnet is embedded at the bottom of the module `` Take caution not to allow any foreign objects between the attaching surfaces. 3. Connect the microphone cable to the camera module. 4.
Assembling the dome cover JJ `` Be careful not to alter the monitoring direction of your camera. [Directly installing on wall/ceiling] 1. Assemble the dome cover. ●● INDOOR DOME CAMERA JJ `` Make sure to firmly tighten the fastening screws so that there is no water damage issue.
flush mount dome camera WHAT’S INCLUDED AT A GLANCE As for each sales country, accessories are not the same. a Bracket b Housing c Camera-module of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection.
INSTALLATION 2. Take off the cushion protecting the camera lens. camera is waterproof and in compliance with the IP52 spec, but the jack connected to the external cable is not. You are JJ `` This recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
flush mount dome camera Removing a Micro SD Memory Card Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot. removing the Micro SD memory card, in , set the device to and press the [Apply] button and turn JJ `` Before the camera off. `` If you turn off the camera or remove the Micro SD memory card that contains data from the product, the data may be lost or Installation (housing) 1.
3. Connect the safety cable. JJ `` A safety cable is not provided. 4-2. Pull out necessary cables among LAN/power/audio & alarm cables through the pipe. ●● FLUSH MOUNT DOME CAMERA e.g. [Using pipe] 4-1. Install the pipe in a fitting hole.
flush mount dome camera Installation (camera case) JJ `` Use a cable bush compliant with the LAN cable to be connected. -- Components: use a cable with the diameter of Ø5 to 8.5 [Installing LAN/power cables] [Installing the LAN cable] 2-1. Pull off the extruded part of the 1-hole bush provided. 2-2. Use the cap installer to pass through the RJ45 cable. Cap Installer 1-1. Pull off the extruded parts of the bush to be used. 1-2.
[Installing audio & alarm cables] 3-1. Mount the bush of the provided audio & alarm cables to the camera case. Installing the camera module 1. Connect the LAN/power/audio & alarm cables to the camera module terminal. 2. Attach the camera module to the case. ●● FLUSH MOUNT DOME CAMERA JJ `` A magnet is embedded at the bottom of the module `` Take caution not to allow any foreign objects between the attaching surfaces. 4. Turn the screws on the housing to fix the housing to the ceiling.
flush mount dome camera Assembling the dome cover Waterproofing cables JJ `` Make sure to firmly tighten the fastening screws so that there is no water damage issue. 1. Connect the power, I/O, and LAN cables. 1. Assemble the dome cover. 4x If there is any possibility of moisture intrusion through the gap of the cable, please waterproof the concerned area with waterproof butyl rubber tape (can be purchased in stores) as below. 2.
outdoor bullet camera WHAT’S INCLUDED AT A GLANCE As for each sales country, accessories are not the same. Pipe-cover b Base Wall Mount d c e Case-bottom f terminal Sunshield Camera-module i Reset button of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power f Network connection Sunshield screw of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power g of the Be ware CAUTION: and Polarity Rated Voltageconnection.
outdoor bullet camera INSTALLATION JJ `` This camera is waterproof and in compliance with the IP67 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed. Removing a Micro SD Memory Card Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot.
Installation (Base Wall Mount) [Directly installing on wall/ceiling] [Installing using pipe] 2-1. Attach the installation template and drill holes for screws and cables. 1-1. Attach the installation template on the desired surface and drill holes for screws and cables. ●● OUTDOOR BULLET CAMERA 2-2. Separate the pipe cover of the Base Wall Mount by pressing its sides. 1-2. Fix the Base Wall Mount using appropriate screws. 1-3.
outdoor bullet camera 2-3. Place the pipe on the Base Wall Mount. 2-4. Fix the Base Wall Mount using appropriate screws. 1-4. Mount the bush to the Case-bottom. 2-5. Pull out necessary cables among LAN/power/audio & alarm cables through the pipe. Installation (Case-bottom) JJ `` Use a cable bush compliant with the LAN cable to be connected. -- Camera main: use a cable with the diameter of Ø5 to 6.5 -- Components: use a cable with the diameter of Ø5 to 8.5 [Installing LAN/power cables] 1-1.
2-3. Mount the bush to the Case-bottom. 4. Join the Base Wall Mount with the Case-bottom. ●● OUTDOOR BULLET CAMERA 3x HEX x4 S3 [Installing audio & alarm cables] 3-1. Mount the bush of the provided audio & alarm cables to the Case-bottom.
outdoor bullet camera Installing the camera module 1. Hang the safety cable up on a hook that looks like an arrow in the Case-bottom. 3. Attach the camera module to the Case-bottom. JJ `` Make sure to firmly tighten the fastening screws so that there is no water damage issue. 3x x4 HEX S3 e.g. 4. Adjust the camera direction using the L wrench provided. 2. Connect the LAN/power/audio & alarm cables to the camera module terminal.
5. Assemble the sunshield to the camera module using sunshield screw. Outdoor installation When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside. 2. Wrap the black cable jacket (Area A) and the cable connection area with waterproof (butyl rubber) tape so that more than half of the butyl rubber tape is overlapped.
box camera WHAT’S INCLUDED AT A GLANCE As for each sales country, accessories are not the same. b Mounting Bracket Screw Hole a Auto Iris Lens (not included) c l Video out k Audio terminal d Micro SD Memory Card Compartment e Lightning protective grounding port AUDIO OUT RESET VIDEO Option (not included) 1234567 AUDIO IN USB FOCUS NETWORK of the Be ware CAUTION: and Polarity Rated Voltageconnection.
MOUNTING THE LENS Disconnect the power before proceeding. Focusing Select a target to film, turn the zoom lever of the lens to adjust the magnification and then focus the lens so that target is clearly displayed. Mounting the CS lens on a camera Turn the CS lens clockwise to attach it. CS Lens focusing with the zoom lever of the lens, press the [FOCUS] button on the rear of the camera to adjust the lens even MM `` After more clearly.
VIDEO box camera FOCUS 1234567 INSERTING/REMOVING A MICRO SD MEMORY CARD Inserting a Micro SD Memory Card AUDIO OUT RESET VIDEO AUDIO OUT VIDEO USB PoE+ AUDIO OUT DC 12V RESET Removing a Micro SD Memory Card VIDEO AUDIO IN USB FOCUS NETWORK Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot.
installation & connection ADJUSTING THE MONITORING DIRECTION FOR THE CAMERA JJ `` Adjust the direction of IR LEDs not to hinder their view by an instrument. JJ `` Adjust the direction of IR LEDs not to hinder their view by a weather cap (if any). ●● INSTALLATION & CONNECTION Tilt Pan Lens rotation `` Adjusting the monitoring direction You can adjust the camera direction only when the camera is fixed on the ceiling.
installation & connection CONNECTING WITH OTHER DEVICE SOFT AP WiFi dongle SOFT AP WiFi dongle Monitor for installation AUDIO OUT RESET VIDEO AUDIO IN USB FOCUS NETWORK Grounding cable 1234567 1 : ALARM 1 5 : GND 2 : ALARM 2 6 : RS-485+ 3 : GND 7 : RS-4854 : ALARM OUT PoE+ DC 12V (12V 50mA) Ethernet Power Power Monitor for installation Ethernet Monitor for installation JJ `` The CVBS out terminal of the product is provided for easier i
Ethernet Connection Connect the Ethernet cable to the local network or to the Internet. Connecting WiFi 1. Connect OTG adapter (5-pin) and WiFi dongle to the micro USB terminal. Smartphone Setup 2. Select the camera SSID after turning on the WiFi. 3. Run the Wisenet Installation application. 4. When you log in to the camera, the video will be connected. `` The video will be played without being logged in during the initial connection. 5.
installation & connection Connecting to Audio Input/Output Microphone AUDIO OUT RESET VIDEO •• Audio Codec -- Audio In : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz), G.
Connecting to the I/O port box Connect the Alarm I/O cable to the corresponding port of the port box. Connecting to the I/O port box(PNB-A9001) Connect the Alarm I/O cable to the corresponding port of the port box.
installation & connection Alarm In Wiring Diagram External connection Inside of the camera VCC_3.3V RESISTOR Sensor ALARM #1(5 mA SINK) RESISTOR RESISTOR DIODE TRANSISTOR MLCC GND GND To connect the alarm out If devices (e.g., flashing light and siren) that exceed the voltage and current specifications are connected by using the open collector method, it may cause malfunction.
network connection and setup You can set up the network settings according to your network configurations. CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE MODEM INTERNET 1. Launch an Internet browser on the local PC. DSL/Cable Modem 2. Enter the IP address of the camera in the address bar of the browser. DDNS Server (Data Center, KOREA) Camera Camera External Remote PC Camera 1. Connect the user PC directly with the network camera.
network connection and setup USING DEVICE MANAGER MM `` Device manager program can be downloaded from - menu at Hanwha Techwin website (http://www.hanwha-security.com). `` More instructions of Device Manager can be found at menu of the main page. AUTOMATICALLY SEARCHING CAMERA If a camera is connected to the same network of the PC where device manager is installed, you can find network camera by using search function. 1.
Configuring Dynamic IP Receive IP address from DHCP -- If connecting the camera directly to modem using the DHCP protocols -- If IPs are assigned by the internal DHCP server via the LAN 1. Click the camera from the list that you want to change the IP setting. 1. Click the camera from the list that you want to automatically configure the IP. PNO-A9081R 2. Click < + > at the main page of device manager. •• Equipment Setting menu appears.
network connection and setup PORT RANGE FORWARD (PORT MAPPING) SETUP If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the Broadband Router so that a remote PC can access the camera in it. Manual Port Range Forwarding 1. From the Setup menu of the Broadband Router, select - . For setting the port range forward for a third-party Broadband Router, refer to the user guide of that Broadband Router. 2.
CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 1. Run device manager. It will scan for connected cameras and display them as a list. ●● NETWORK CONNECTION AND SETUP 2. Double-click a camera to access. The Internet browser starts and connects to the camera. MM `` Access to the camera can also be gained by typing the camera’s IP address in the address bar of the Internet browser.
web viewer CONNECTING TO THE CAMERA Normally, you would 1. Launch the Internet browser. 2. Type the IP address of the camera in the address bar. ex) • IP address (IPv4) : 192.168.1.100 http://192.168.1.100 - the Login dialog should appear. • IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111 http://[2001:230:abcd:ffff:0000:0000:ffff:1111] - the Login dialog should appear. If the HTTP port is other than 80 1. Launch the Internet browser. 2.
PASSWORD SETTING When you access the product for the first time, you must register the login password. characters. For a password with 10 to 15 digits, you must use at least 2 types of those mentioned. -- Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].?/ 1. Click the [Setup ( )] icon. 2. The Settings window appears. 3. You can configure settings for the camera’s basic information, video, audio, network, event, analysis, and system over the network. 4.
appendix SPECIFICATION Description Items Imaging Device Effective Pixels Video Min. Illumination Video Out Focal Length (Zoom Ratio) Max. Aperture Ratio Lens Angular Field of View Min. Object Distance Focus Control Lens Type Pan / Tilt / Rotate Pan / Tilt / Rotate range IR Viewable Length Camera Title Day & Night Operational Backlight Compensation Wide Dynamic Range Digital Noise Reduction Digital Image Stabilization Motion Detection 54_ appendix 1/1.
Description Items Ethernet PNV-A9081R H.265/H.264: Main/High, MJPEG Resolution 3840x2160, 3072x1728, 2592x1944, 2688x1520, 2560x1440, 2048x1536, 1920x1080, 1600x1200, 1280x1024,1280x960, 1280x720, 1024x768, 800 x 600, 800 x 448, 720 x 576, 720x480, 640x480, 640x360 Smart Codec Video Quality Adjustment Bitrate Control Streaming Audio Compression Protocol HTTPS(SSL) Login Authentication Digest Login Authentication Security H.265/H.264: Max. 30fps/25fps(60Hz/50Hz) MJPEG: Max.
appendix Description Items Imaging Device 1/1.8” 8MP CMOS Min. Illumination Color: 0.05Lux(F1.6, 1/30sec) BW: 0Lux(IR LED on) Effective Pixels Video Video Out Focal Length (Zoom Ratio) Max. Aperture Ratio Lens Angular Field of View Min.
Description Items Ethernet PND-A9081RV H.265/H.264: Main/High, MJPEG Resolution 3840x2160, 3072x1728, 2592x1944, 2688x1520, 2560x1440, 2048x1536, 1920x1080, 1600x1200, 1280x1024,1280x960, 1280x720, 1024x768, 800 x 600, 800 x 448, 720 x 576, 720x480, 640x480, 640x360 Smart Codec Video Quality Adjustment Bitrate Control Streaming Audio Compression Protocol HTTPS(SSL) Login Authentication Digest Login Authentication Security H.265/H.264: Max. 30fps/25fps(60Hz/50Hz) MJPEG: Max.
appendix Description Items Imaging Device 1/1.8” 8MP CMOS Min. Illumination Color: 0.05Lux(F1.6, 1/30sec) BW: 0Lux(IR LED on) Effective Pixels Video Video Out Focal Length (Zoom Ratio) Max. Aperture Ratio Lens Angular Field of View Min.
Description Items Ethernet PND-A9081RF H.265/H.264: Main/High, MJPEG Resolution 3840x2160, 3072x1728, 2592x1944, 2688x1520, 2560x1440, 2048x1536, 1920x1080, 1600x1200, 1280x1024,1280x960, 1280x720, 1024x768, 800 x 600, 800 x 448, 720 x 576, 720x480, 640x480, 640x360 Smart Codec Video Quality Adjustment Bitrate Control Streaming Audio Compression Protocol HTTPS(SSL) Login Authentication Digest Login Authentication Security H.265/H.264: Max. 30fps/25fps(60Hz/50Hz) MJPEG: Max.
appendix Description Items Imaging Device 1/1.8” 8MP CMOS Min. Illumination Color: 0.05Lux(F1.6, 1/30sec) BW: 0Lux(IR LED on) Effective Pixels Video Video Out Focal Length (Zoom Ratio) Max. Aperture Ratio Lens Angular Field of View Min.
Description Items Ethernet PNO-A9081R H.265/H.264: Main/High, MJPEG Resolution 3840x2160, 3072x1728, 2592x1944, 2688x1520, 2560x1440, 2048x1536, 1920x1080, 1600x1200, 1280x1024,1280x960, 1280x720, 1024x768, 800 x 600, 800 x 448, 720 x 576, 720x480, 640x480, 640x360 Smart Codec Video Quality Adjustment Bitrate Control Streaming Audio Compression Protocol HTTPS(SSL) Login Authentication Digest Login Authentication Security H.265/H.264: Max. 30fps/25fps(60Hz/50Hz) MJPEG: Max.
appendix Description Items Video Imaging Device 1/1.8” 8MP CMOS Min. Illumination Color: 0.03Lux(F1.2, 1/30sec) Effective Pixels Video Out Lens Focus Control Lens Type Mount Type Camera Title Day & Night Backlight Compensation Wide Dynamic Range Digital Noise Reduction Operational Digital Image Stabilization Motion Detection Privacy Masking Gain Control White Balance LDC 62_ appendix PNB-A9001 Electronic Shutter Speed 3864(H) x 2180(V) Digital PTZ Video Rotation CVBS: 1.
Description Items Ethernet PNB-A9001 H.265/H.264: Main/High, MJPEG Resolution 3840x2160, 3072x1728, 2592x1944, 2688x1520, 2560x1440, 2048x1536, 1920x1080, 1600x1200, 1280x1024,1280x960, 1280x720, 1024x768, 800 x 600, 800 x 448, 720 x 576, 720x480, 640x480, 640x360 Smart Codec Video Quality Adjustment Bitrate Control Streaming Network H.265/H.264: Max. 30fps/25fps(60Hz/50Hz) MJPEG: Max. 15fps/12fps(60Hz/50Hz) Manual(5ea area), WiseStream H.264/H.
appendix PRODUCT OVERVIEW PND-A9081RV PNV-A9081R Unit : mm [inch] Unit : mm [inch] Ø100 [3.94] 160 [6.3] Ø180 [7.09] Ø100 [3.94] Ø88 [3.46] Ø88 [3.46] 85.2 [3.36] 46 [1.81] 80 [3.15] 83.5 [3.29] 85.2 [3.36] 46 [1.81] 85.2 [3.36] 64_ appendix 85.2 [3.36] 90 [3.54] 46 [1.81] 125 [4.92] 125 [4.
PND-A9081RF Unit : mm [inch] Unit : mm [inch] ●● APPENDIX Ø100 [3.94] PNO-A9081R Ø180 [7.09] Ø205 [8.07] 200.9[7.91] 188[7.40] 180.6[7.11] 368.6[14.51] 70 [2.76] 163 [6.42] ] 58 [3.
appendix PNB-A9001 Unit : mm [inch] 2-1/4inch-20UNC TAP 165 [6.48] 81 [3.19] 67 [2.64] 158 [6.
TROUBLESHOOTING PROBLEM What are the specifications for WAVE files necessary to play audio at the time of an event? No video is displayed when accessing the plug-in free webviewer on Safari via HTTPS. yy This is what happens when microphone driver has been set to Realtek driver. Install the High Definition Audio device (Windows Default Driver) or the third party driver as the microphone driver. yy Sampling rate of 48,000 KHz or less is recommended.
OPEN SOURCE ANNOUNCEMENT GPL/LGPL software license If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source distribution might be charged. Component Name License Base Kernel Busybox iproute2-4.3.0 iptables-1.4.21 ethtool-4.2 mtd-1.5.2 mii-diag-2.11 rp-pppoe-3.11 wpa_supplicant-2.5 bash-4.3.30 zeroconf GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 3.0 GPL 2.
components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 4.
2. Basic Permissions. All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions are met. This License explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is covered by this License only if the output, given its content, constitutes a covered work. This License acknowledges your rights of fair use or other equivalent, as provided by copyright law.
patent license to some of the parties receiving the covered work authorizing them to use, propagate, modify or convey a specific copy of the covered work, then the patent license you grant is automatically extended to all recipients of the covered work and works based on it.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. yy Neither the name of Sparta, Inc nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
1.11. "Source Code" means the preferred form of the Covered Code for making modifications to it, including all modules it contains, plus any associated interface definition files, scripts used to control compilation and installation of an Executable, or source code differential comparisons against either the Original Code or another well known, available Covered Code of the Contributor’s choice.
provides that the language of a contract shall be construed against the drafter shall not apply to this License. 12. RESPONSIBILITY FOR CLAIMS. As between Initial Developer and the Contributors, each party is responsible for claims and damages arising, directly or indirectly, out of its utilization of rights under this License and You agree to work with Initial Developer and Contributors to distribute such responsibility on an equitable basis.
16. "Patch for Modification" means a difference, program, system, or the like in order to create the Modified Source Code from the Source Code or the Binary Code thereof. 17. "Vicarious Execution of Patch Processing" means vicarious execution service to create the Modified Source Code applying the Patch for Modification to the Source Code or the Binary Code thereof. 18. "Source Code User" means a person who uses the Source Code. 19.
"Legal Entity" shall mean the union of the acting entity and all other entities that control, are controlled by, or are under common control with that entity. For the purposes of this definition, "control" means (i) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (ii) ownership of fifty percent (50%) or more of the outstanding shares, or (iii) beneficial ownership of such entity.
PHP 3.01 License The PHP License, version 3.01 Copyright (c) 1999 - 2010 The PHP Group. All rights reserved. Component Name License URL php-5.2.17 PHP 3.01 http://www.php.net/distributions Redistribution and use in source and binary forms, with or without modification, is permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
Head Office 6, Pangyo-ro 319 beon-gil, Bundang-gu, Seongnam-si, Gyeonggi-do, 463-400 Rep. of KOREA Tel : +82.70.7147.8753 Fax : +82.31.8018.3740 www.hanwha-security.com Hanwha Techwin America 500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666 Toll Free +1.877.213.1222 Direct +1.201.325.6920 Fax +1.201.373.0124 www.hanwhasecurity.com Hanwha Techwin Europe Heriot House, Heriot Road, Chertsey, Surrey, KT16 9DT, United Kingdom Tel +44.1372.235663 Fax +44.1932.57.8101 www.hanwha-security.
