Contact SAMSUNG WORLD-WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre. Country AUSTRIA Customer Care Centre 0800-SAMSUNG(726-7864) Web Site www.samsung.com/at BELGIUM 0032 (0)2 201 24 18 www.samsung.com/be 844 000 844 www.samsung.com/cz CZECH REPUBLIC Distributor pro Českou republiku: Samsung Zrt., česka organizační složka Vyskočilova 4, 14000 Praha 4 DENMARK 70 70 19 70 www.samsung.com/dk EIRE 0818 717 100 www.
User Instructions Screen Image retention Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image. Height The PDP can normally operate only under 2000m in height.
General Information Function Description User Instructions.............................................. 2 Checking Parts................................................. 4 Using the Stand-Base...................................... 4 Control Panel .................................................. 5 Connection Panel............................................. 6 Viewing the Remote Control............................ 8 Operation Switching Your Television On and Off..............
Checking Parts Owner’s Instructions Remote Control/ AAA Batteries Power Cord Cloth-Clean Warranty Card/ Safety Guide Manual (Not available in all locations) Cover-Bottom / Screws (2ea) (Refer to page 52) Ferrite Core for Power Cord Ferrite Core for S-Video Sold Separately Antenna Cable Component Cables Audio Cables PC Cable Scart Cable PC Audio Cable HDMI Cable HDMI/DVI Cable Core (Power Cord, S-Video) ➢ Ferrite The ferrite cores are used to shield the cables from interference.
Control Panel Front (or Side) Panel ➢ The product colour and shape may vary depending on the model. 1 SOURCE Toggles between all the available input sources (TV, Ext.1, Ext.2, AV, S-Video, Component, PC, HDMI1, HDMI2, HDMI3 and DTV). ➢ In the on-screen menu, use this button as you would use the ENTER button on the remote control. 2 MENU Press to see an on-screen menu of your TV’s features. 3 – + Press to increase or decrease the volume.
Connection Panel Rear Panel 1 0 or Cable Television Network 7 or 2 ➢ ☛ 3 4 5 6 8 9 The product colour and shape may vary depending on the model. Whenever you connect an audio or video system to your set, ensure that all elements are switched off. When connecting an external device, match the colour of the connection terminal to the cable. 1 POWER IN Connect the supplied power cord. 5 DIGITAL AUDIO OUT (OPTICAL) Connect to a Digital Audio Component.
9 HDMI IN 1,2 − No additional Audio connection is needed for an HDMI to HDMI connection. - When using an HDMI/DVI cable connection, you must use the HDMI IN 2 jack. What is HDMI? - “High Definition Multimedia interface” allows the ansmission of high definition digital video data and multiple channels of digital audio. - The HDMI/DVI terminal supports DVI connection to an extended device with the appropriate cable (not supplied).
Viewing the Remote Control ➢ The performance of the remote control may be affected by bright light. 1 POWER button (turns the TV on and off) 2 Selects the TV and DTV mode directly 3 Number buttons for direct channel access 4 One/Two-digit channel selection 5 Temporary sound switch-off 6 Volume increase Volume decrease 7 Electronic Program Guide (EPG) display 8 Use to quickly select frequently used functions.
Installing Batteries in the Remote Control 1 Lift the cover at the back of the remote control upward as shown in the figure. 2 Install two AAA size batteries. Make sure to match the “+” and “–” ends of the batteries with the diagram inside the compartment. Do not mix battery types, i.e. alkaline and manganese. 3 Close the cover as shown in the figure. Remove the batteries and store them in a cool and dry place if you won’t be using the remote control for a long time.
Plug & Play Feature When the television is initially powered on, several basic customer settings proceed automatically and subsequently. The following settings are available. If you accidentally select the wrong country for your TV, the characters on the screen may be wrongly displayed. Any functions related to Digital TV (DVB) will only work in countries or areas where DVB-T (MPEG2) digital terrestrial signals are broadcasted. Please confirm with your local dealer if you can receive DVB-T signals.
f the country is set to Others, Clock Set screen appears ☛ Iwhen searching for the analog channel is finished. If the Sweden, Denmark, or Finland is selected, the analog and then digital channels are searched, and the Clock Set is preceded in order. For more information about digital channel searching, refer to page 32. 8 Plug & Play Clock Set Month Day -- Year Hour ---- Move Press the ◄ or ► button to select Month, Day, Year, Hour, or Minute. Set these by pressing the ▲ or ▼ button.
Using the TOOLS Button You can use the TOOLS button to select your frequently used functions quickly and easily. The “Tools” menu changes depending on which external input mode you are viewing. 1 Press the TOOLS button. The Tools menu will appear. Tools 2 Press the ▲ or ▼ button to select a menu, then press the ENTER button. 3 Press the ▲/▼/◄/►/ENTER buttons to display, change, or use the selected items. For a more detailed description of each function, refer to the corresponding page.
Editing Device Names You can give a name to the external source. 1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Input, then press the ENTER button. 3 Press the ▲ or ▼ button to select Edit Name, then press the ENTER button. 4 Press the ▲ or ▼ button to select the external source to be edited, then press the ENTER button. 5 Select the required device by pressing ▲ or ▼, then press the ENTER button.
Storing Channels Manually Not available in DTV or external input mode. ➢ You can store television channels, including those received TV via cable networks. When storing channels manually, you can choose: Whether or not to store each of the channels found. The programme number of each stored channel which you wish to identify. 1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Channel, then press the ENTER button.
Adding / Locking Channels Not available in DTV or external input mode. ➢ Using the Channel Manager, you can conveniently lock or add TV channels. 1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Channel, then press the ENTER button. 3 Press the ▲ or ▼ button to select Channel Manager, then press the ENTER button. Adding channels Using the Channel List, you can add channels. 4 Select Channel List by pressing the ENTER button.
Sorting the Stored Channels Not available in DTV or external input mode. ➢ This operation allows you to change the programme numbers TV of the stored channels. This operation may be necessary after using the auto store. 1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Channel, then press the ENTER button. 3 Press the ▲ or ▼ button to select Sort, then press the ENTER button.
Fine Tuning Channel Reception Not available in DTV or external input mode. ➢ If the reception is clear, you do not have to fine tune the TV Channel Country : United Kingdom Auto Store Manual Store Channel Manager Sort Name Fine Tune channel, as this is done automatically during the search and store operation. If the signal is weak or distorted, you may have to fine tune the channel manually. 1 Press the MENU button to display the menu.
Changing the Picture Standard You can select the type of picture which best corresponds to your viewing requirements. 1 Press the MENU button to display the menu. 2 Press the ENTER button to select Picture. 3 Press the ENTER button again to select Mode. 4 Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button. Available modes: Dynamic, Standard, Movie The settings values may vary depending on the input source. ➢ 5 ➢ TV Move TV Press the EXIT button to exit.
Configuring Detailed Settings on the Picture You can set detailed picture settings. 1 Press the MENU button to display the menu. 2 Press the ENTER button to select Picture. 3 Press the ▲ or ▼ button to select Detailed Settings, then press the ENTER button. 4 Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
Picture Options You can set detailed picture settings. 1 Press the MENU button to display the menu. 2 Press the ENTER button to select Picture. 3 Press the ▲ or ▼ button to select Picture Options, then press the ENTER button. 4 Select the required option by pressing the ▲ or ▼ button, then press the ENTER button. 5 When you are satisfied with your setting, press the ENTER button. 6 Press the EXIT button to exit.
TV Picture Options Screen Mode: 16:9/Wide Zoom/Zoom/4:3 Colour Tone : Normal When setting the picture size to Auto Wide in a 16:9 wide TV, Size : Auto Wide you can determine the picture size you want to see the 4:3 Screen Mode : 16:9 16:9 Digital NR : Wide Zoom WSS (Wide Screen Service) image or nothing. Each individual Real 100 Hz Demo : Off Zoom European country requires different picture size so this function DNle : 4:3 is intended for users to select it.
➢ Optimum condition for pixel shift; Horizontal Dot Vertical Line Time (minute) PC 1 1 2 TV TV/Ext/AV/Component/HDMI/DTV 2 2 2 min ➢ The Pixel Shift value may differ depending on the monitor size (inches) and mode. ➢This function is not available in the Just Scan mode. Pixel Shift Pixel Shift Horizontal Dot Vertical Line Time Move : On : : : min Enter Return − White: This function helps remove after images on the screen by changing the colour of pixels to white.
1 2 3 4 Connect a HDMI/DVI cable between the HDMI IN 2 jack on the TV and the PC output jack on your computer. Connect a 3.5mm Stereo/2RCA cable between the DVI IN (HDMI 2) [R-AUDIO-L] jack on the TV and the Audio Out jack of the sound card on your computer. Connect the Emitter to the 3D SYNC OUT port on the rear panel of the TV. Turn the TV on and set the source of the TV to HDMI2.
Changing the Format Select the optimal input format to match your graphic cards or 3D software. TV 3D Effect Mode Format : Mode 1 : Checker Board Horizontal Vertical See the descriptions for Steps 1 to 4 above. 5 6 Press the ▲ or ▼ button to select Format, then press the ENTER button. Press the ▲ or ▼ button to select Checker Board, Horizontal or Vertical then press the ENTER button.
Sound Features 1 2 TV Sound Press the MENU button to display the menu. Mode : Custom Press the ▲ or ▼ button to select Sound, then press the Equalizer SRS TS XT : Off ENTER button. Auto Volume : Off 3 Select the required option by pressing the ▲ or ▼ button, then TV Speaker : Off press the ENTER button. Available options: Mode, Equalizer, SRS TS XT, Auto Volume, TV Speaker Move Enter Return 4 When you are satisfied with your setting, press the ENTER button.
Selecting the Sound Mode (depending on the model) The DUAL I-II button displays/controls the processing and output of the audio signal. When power is switched on, the mode is automatically preset to either “DUAL-I” or “Stereo”, depending on the current transmission. Easy Setting 1 Press the TOOLS button on the remote control. 2 Press the ▲ or ▼ button to select Dual I-II. 3 Press the ◄ or ► button to select the required option.
Time Features 1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Setup, then press the ENTER button. 3 Press the ▲ or ▼ button to select Time, then press the ENTER button. 4 Select the required option by pressing the ▲ or ▼ button, then press the ENTER button. Available options: Clock Set, Sleep Timer, Timer 1, Timer 2, Timer 3 5 When you are satisfied with your setting, press the ENTER button. 6 Press the EXIT button to exit.
Language / Melody / Light Effect / Entertainment / Energy Saving 1 2 TV Setup Press the MENU button to display the menu. Plug & Play Press the ▲ or ▼ button to select Setup, then press the Language : English Time ENTER button. Light Effect : In Watching TV Wall-Mount Adjustment 3 Select the required option by pressing the ▲ or ▼ button, then Melody : Off Entertainment : Off press the ENTER button.
Energy Saving: Off/Low/Medium/High Tools This feature adjusts the screen brightness depending on the Anynet+ (HDMI-CEC) surrounding lighting conditions. Picture Mode : Standard − Off: Switches off the Energy Saving mode. Sound Mode : Custom Sleep Timer : Off − Low: Operates in standard mode regardless of the SRS TS XT : Off Energy Saving ◄ Off surrounding illumination. Dual I-II : Mono − Medium: Enters Medium power saving mode regardless of Adjust Move the surrounding illumination.
Input Mode (PC) Both screen position and size will vary depending on the type of PC monitor and its resolution. The table below shows all of the display modes that are supported: D-Sub Input Mode Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock Frequency (MHz) Sync Polarity (H/V) PS50A476 IBM 640 x 350 720 x 400 31.469 31.469 70.086 70.087 25.175 28.
Setting the PC ➢ Preset to the PC mode by pressing the SOURCE button. 1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Picture, then press the ENTER button. 3 Select the required option by pressing the ▲ or ▼ button, then press the ENTER button. 4 When you are satisfied with your setting, press the ENTER button. 5 Press the EXIT button to exit. Auto Adjustment : Auto adjustment allows the PC screen of set to self-adjust to the incoming PC video signal.
Previewing the DTV Menu System Available in DTV mode. Preset to the DTV mode by using the ➢ TV/DTV button on your remote control. TV To help you navigate around the on-screen menu system and adjust the various settings available, refer to the following illustration. Press the MENU button to display the menu. Press the ▲ or ▼ button to select Digital Menu, then press the ENTER button.
Language Audio Language Subtitle Language Teletext Language Preference DTV Language Audio Language Subtitle Language Teletext Language Preference Primary Audio Language Secondary Audio Language Primary Subtitle Language Move Enter Secondary Subtitle Language Primary Teletext Language Secondary Teletext Language (depending on the Country) Return ➢ The sub-items of the CI Menu may vary depending on the CAM model.
1.2 Auto Store You can update the channel list when the broadcaster adds new services or if you move the TV to a new location. Press the ENTER button to select Auto Store. Choose system to scan by pressing the ▲ or▼ button, then press the ENTER button. - When selecting "Denmark/Sweden": Set the Frequency, Modulation,Symbol rate and Network ID in Cable and press the Red button to search. Press the ENTER button in Aerial to search.
Press the red button to start the scan for digital services. When it has finished, channels are updated in the channel list. You can input by pressing the button on the remote control. You can not change only frequency and when changing a channel the Frequency will be automatically changed. ➢ ➢ 1.4 Edit Favourite Channels DTV Channel You can edit your favourite channels using the colour buttons.
Channel List 1.5 Channel List BBC TWO All Channels-All You can display a list of all channels or your favourite 1. Test Card ‘M’... 806 arte 40. BBC NEWS24 channels. 51. BBCi 2. BBC TWO 800 ARD-MHP-DATA 3. Vida003b 801 ARD-OnLine-K.. 4. Vida004b Press the ▲ or ▼ button to select Channel List, then 802 BBC ONE 5. Vida005b 803 MDR FERNSE.. press the ENTER button. 6. Vida006b 804 NDR FERNSEH.. 7. BBC THREE It can be displayed simply by pressing the CH LIST 30. CBBC Channel 805 Vida002b button.
To view programme information, press the ▲/▼/◄/► button to select a programme of your choice, then press the INFO button. Information such as the channel number, programme title and running time, status bar, and brief summary of the highlighted programme will be displayed in the top right corner of the screen. If there is a lengthy summary, “…” will be displayed. Press the INFO button for the full summary text. Six channels are displayed.
2.4 All Channels and Favorite Channels In the EPG menu, you can display all channels or favourite channels. Press the green button repeatedly to toggle between the all and favourite channels list. When the favorite channel list has not been set up: − The favorite list is empty. Would you like to choose your favorite now? message is displayed. − Select Yes. The Edit Favourite Channels menu is displayed. If you select No, all channels will remain unchanged.
DTV Language 3.2 Preference This menu consists of 6 sub-menus: Audio Language Primary Audio Language, Secondary Audio Language, Subtitle Language Primary Subtitle Language, Secondary Subtitle Language, Teletext Language Primary Teletext Language, and Secondary Teletext Preference Language (depending on the Country). Using this feature, users can select one of the languages (English, German, Italian, Swedish, French, Welsh, Gaelic, Move Enter Return Irish, Danish, Finnish, Spanish, Dutch).
4. Setup This menu consists of 11 sub-menus: Menu Transparency, Change PIN, Parental Lock, Subtitle, Subtitle Mode, Audio Format, Audio Description, Digital Text, Time Zone, Common Interface and System. 4.1 Menu Transparency You can set the translucency of the on-screen menu. Press the ▲ or ▼ button to select required option (High, Medium, Low, or Opaque), then press the ENTER button. 4.
DTV Setup 4.3 Subtitle / Subtitle Mode / Audio Format / Audio Description / Digital Text Menu Transparency : Medium You can use various settings to suit your personal preferences. Change PIN Parental Lock Press the ▲ or ▼ button to select required menu Subtitle : On (Subtitle, Subtitle Mode, Audio Format, Audio Subtitle Mode : Normal Description or Digital Text), then press the ENTER button. The options of the selected menu are displayed.
4.5 Common Interface − Installing the CI Card Purchase the CI CAM module by visiting your nearest dealer or by phone. Insert the CI CARD into the CAM in the direction of the arrow until it fits. Insert the CAM with the CI CARD installed into the common interface slot. Insert the CAM in the direction of the arrow, right up to the end so that it is parallel with the slot. Check if you can see a picture on a scrambled signal channel. You can install the CAM anytime whether the TV is ON or OFF.
DTV Software Upgrade − Software Upgrade (Option) To keep your product up-to-date with new digital television Software Information features then software upgrades are periodically broadcast Manual Upgrade as part of the normal television signal. It will automatically Standby Mode upgrade : On detect these signals and display the software upgrade banner. You are given the option to install the upgrade.
What is Anynet+? Anynet+ is an AV network system that enables an easy-to-use AV interface for users by controlling all connected AV devices through the Anynet+ menu when Samsung Electronics AV devices are connected. Connecting Anynet+ Devices The Anynet+ system supports AV devices supporting Anynet+ only. Check if there is an Anynet+ mark on the AV device to be connected to the TV.
Setting Up Anynet+ The following settings are to use Anynet+ functions. Using the Anynet+ Function 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Input, then press the ENTER button. 2 Press the ▲ or ▼ button to select Anynet+ (HDMI-CEC), then press the ENTER button. 3 Press the ▲ or ▼ button to select Setup, then press the ENTER button. 4 Press the ▲ or ▼ button to select Anynet+ (HDMI-CEC), then press the ENTER button.
Anynet+ Menu The Anynet+ menu changes depending on the type and status of the Anynet+ devices connected to the TV. Anynet+ Menu View TV Select Device Record Menu on Device Device Operation Receiver Setup Description Switches from Anynet+ to TV broadcast mode. Your TV connects to the corresponding device. Starts a recording. (This menu works only for a device supporting recording.) Shows the menu of the connected device. Example. When a DVD Recorder is connected, the DVD Recorder’s title menu appears.
Listening through a Receiver You can listen to sound through a receiver instead of the TV speaker. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Input, then press the ENTER button. TV P1 2 Press the ▲ or ▼ button to select Anynet+ (HDMI-CEC), then press the ENTER View TV button. Select Device 3 Press the ▲ or ▼ button to select Receiver, then press the ENTER button. Record 4 Press the ◄ or ► button to select to On, then press the ENTER button.
Teletext Feature (depending on the model) Most television stations provide written information services via teletext. The index page of the teletext service gives you information on how to use the service. In addition, you can select various options to suit your requirements by using the remote control buttons. For teletext information to be displayed correctly, channel reception must be stable. Otherwise, information may be missing or some pages may not be displayed.
The teletext pages are organized according to six categories: Part A B C D E F Contents Selected page number. Broadcasting channel identity. Current page number or search indications. Date and time. Text. Status information. FASTEXT information.
Wall Mount Kit Specifications (VESA) Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest dealer. If installed on a ceiling or slanted wall, it may fall and result in severe personal injury. Product Family inch VESA Spec.
Wall- mount adjustment (Sold separately) Once the auto wall mount is installed, the position of your TV can be easily adjusted. Rear Panel Auto Wall-Mount Serial Cable(1P to 1P)(Not supplied) Entering the menu Press the ▲, ▼, ◄ or ► button on your remote control. ➢ The Wall Mount Adjustment screen is displayed. ➢ If the Wall Mount Adjustment screen is not displayed when clicking on a direction button while watching your TV, use the menu to display that screen.
Moving to the remembered position 1 Complete Step 1 of Entering the menu. 2 Pressing a Color (Red, Green, Yellow) button moves the auto wall mount to the saved position. ➢ You can move the wall mount to one of the 3 pre-set positions by pressing the Red (Position 1), Green Position 1 2 3 (Position 2) or Yellow (Position 3) buttons. Adjust Save Center ➢ If you adjust the positon after moving to a pre-set position, the position display will disappear.
Securing the TV to the Wall Caution Pulling, pushing, or climbing on the TV may cause the TV to fall. In particular, ensure your children do not hang over or destabilize the TV; doing so may cause the TV to tip over, causing serious injuries or death. Follow all safety precautions provided on the included Safety Flyer. For added stability, install the anti-fall device for safety purposes, as follows. To avoid the TV from falling: 1. Put the screws into the clamps and firmly fasten them onto the wall.
Troubleshooting Before contacting the Samsung after-sales service, perform the following simple checks. If you cannot solve the problem using the instructions below, note the model and serial number of the television and contact your local dealer. No sound or picture Check that the mains lead has been connected to a wall socket. Check that you have pressed the (Power) button (On/Off) on the front panel or press the POWER button on the remote control. Check the picture contrast and brightness settings.
Specifications The descriptions and characteristics in this booklet are given for information purposes only and are subject to modification without notice.
This page is intentionally left blank. BN68-01422C.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.
