NETWORK CAMERA User Manual QND-7012R/7022R/7032R/7082R QNV-6014R/7012R/7022R/7032R/6084R/7082R QNO-6014R/7012R/7022R/7032R/6084R/7082R
Network Camera User Manual Copyright ©2021 Hanwha Techwin Co., Ltd. All rights reserved. Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
overview IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth. (Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.) 7.
overview Class construction Please read the following recommended safety precautions carefully. An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection. ~ Do not place this apparatus on an uneven surface. ~ Do not install on a surface where it is exposed to direct sunlight, near heating equipment or heavy cold area. ~ Do not place this apparatus near conductive material. ~ Do not attempt to service this apparatus yourself.
CONTENTS OVERVIEW 6 6 8 9 11 12 14 INSTALLATION & CONNECTION 16 16 17 18 20 23 27 NETWORK CONNECTION AND SETUP 31 31 31 32 32 32 33 33 34 35 35 Important Safety Instructions Recommended PC Specifications Recommended Micro SD/SDHC/SDXC Memory Card Specifications NAS recommended specs What’s Included At a Glance (QND-7012R/7022R/7032R) At a Glance (QND-7082R) At a Glance (QNO-6014R/7012R/7022R/ 7032R/6084R/7082R) At a Glance (QNV-6014R/7012R/7022R/ 7032R) At a Glance (QNV-6084R/7082R) WEB VIEWER 36
overview RECOMMENDED PC SPECIFICATIONS WHAT’S INCLUDED CPU : Intel(R) Core(TM) i7 3.4 GHz or higher RAM : 8G or higher Recommended browser: Chrome Supported browsers: Chrome, Safari, Firefox, MS Edge(chromium based) Supported OS : Windows, Mac, Linux, Android, iOS, Chrome Verification environment - Windows 10: Google Chrome version 80 or later, Firefox version 72 or later, MS Edge version 83 or later - Mac 10.13/14: Safari version 11.0.
Appearance Quantity Description Model Name L Wrench 1 Used to control the direction of the camera QNO-6014R/ 7012R/7022R/ 7032R/6084R/7082R 1 Used to remove and replace the dome cover QNV-6014R/ 7012R/7022R/ 7032R/6084R/7082R Used when connecting to an alarm QND-7012R/7022R/ 7032R/7082R Torx L wrench Alarm cable RJ45 waterproof accessory 1 1 Used to install in humid places 1 It protects the camera from the direct sunlight.
overview AT A GLANCE (QND-7012R/7022R/7032R) Components Appearance bcd a a NET AC WO T LI RK NK AC NE T LIN TW OR K K RESET ON T DC b c FR ON T DC 12 12 V Item Description Dome cover Case cover used to protect the lens and the main unit. b Camera Case Housing part that covers the camera body. c Microphone hole Microphone is embedded. DC 1 2V FR ON T a NE T AC WOR TL K INK jk 8_ overview VIDEO D 4 5 GN 1. ALM IN 2. ALM OUT 3. 4. GND T M IN M OU 2. AL 1. AL 5.
Item Description Inside cover Protective cover for the main body. b Illumination Sensor Detects incoming light to control the IR LED. c Lens Lens for the camera. d IR LED These infrared LED’s are controlled by the illumination sensor. Appearance ! OVERVIEW a AT A GLANCE (QND-7082R) a The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.
overview Components Item bc a d NETWORK IN UT RM O LA RM LINK ACT a Inside cover Protective cover for the main body. b Illumination Sensor Detects incoming light to control the IR LED. c Lens Lens for the camera. d IR LED These infrared LED’s are controlled by the illumination sensor. e Power Port Port for power terminal block. f Microphone hole Microphone is embedded. g Network Port Used to connect the PoE or Ethernet cable for network connection.
AT A GLANCE (QNO-6014R/7012R/7022R/7032R/6084R/7082R) Item Appearance a Micro SD Card slot Description (Internal space of the product) This is a slot in which you can insert a Micro SD card. a bc d e J If you reset the camera, the network settings will be adjusted so that DHCP can be enabled. If there is no DHCP server in the network, you must run the Device Manager program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network.
overview AT A GLANCE (QNV-6014R/7012R/7022R/7032R) Components Appearance a CAUTION: Be ware of the Rated Voltage and Polarity of the power connection. b c a d b + AC 24 V/ DC - 12 T V F N Description Used to plug the power cable. ARM-OUT Used to connect the alarm output signal. GND These are common ports to connect alarm input/output signals. ARM-IN Used to connect the alarm input sensor or external day/night sensor.
Components Item a Illumination Sensor Detects incoming light to control the IR LED. b Lens Lens for the camera. c IR LED These infrared LED’s are controlled by the illumination sensor. ! OVERVIEW a bc Description The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system. d e f T RESE DC 2 3 45 GN D VID EO 2 .AL 3.A .
overview AT A GLANCE (QNV-6084R/7082R) Components Appearance ab c a b - T V F T F N N W W AF O VIDE RESE T IN UT AF VID EO RESE Item d e f g DC12V 12 12 DC 1 2 AL 5 AL AR A A M U R D M IN IO O V/ NT O FR 24 3 4 GN 56 D 7 + AC h Description a Dome cover Case cover used to protect the lens and the main unit. b Camera Case Housing part that covers the camera body.
Item Description Illumination Sensor Detects incoming light to control the IR LED. b Lens Lens for the camera. c IR LED These infrared LED’s are controlled by the illumination sensor. d Audio/Alarm cable port ARM-IN Used to connect the alarm input sensor or external day/night sensor. ARM-OUT Used to connect the alarm output signal. GND These are common ports to connect alarm input/output signals. AUDIO IN Used to connect to a microphone.
installation & connection INSTALLATION (QND-7012R/7022R/7032R/7082R) Installation 1. Consider the direction to be monitored, attach the template, and drill holes by following the template. Precautions before installation Ensure you read out the following instructions before installing the camera: V 12 T ON FR J DC 1. Use one hand to hold the camera’s bottom part and turn the cover counterclockwise with another hand to separate it. 3. 4. GND Dome Cover VIDEO 3.
INSTALLATION (QNO-6014R/7012R/7022R/7032R/6084R/7082R) J ` This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed. How to connect the RJ45 waterproof cable to a LAN cable 1. Insert it through the arrow direction.
installation & connection INSTALLATION (QNV-6014R/7012R/7022R/7032R) Outdoor installation When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside. 1. Connect the power, I/O, AUDIO, and LAN cables. 2.
Connecting the audio/alarm cable and power cable 5. Close the dome cover. ` Securely fasten the fastening bolt using an Torx L wrench to prevent water from leaking. 1. Remove the dome cover and the case. 1 2 3 45 GN D 2. Pull off the cable bush at the bottom as shown in the figure. 12 DC V VID EO 2. .ALM 3. AL AU M IN DI O O UT IN RESET ! INSTALLATION & CONNECTION 3. Pull off the small extruded part on the bush of the alarm/audio cable, and route the power cable through the bush.
installation & connection INSTALLATION (QNV-6084R/7082R) J Installation ` This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are 1. Consider the direction to be monitored, attach the template, and drill holes by following the template. recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Connecting the LAN cable Connecting the audio/alarm cable and power cable 1. Remove the dome cover and the case. 1. Remove the dome cover and the case. 2. Pull off the cable bush at the bottom as shown in the figure. 2. Pull off the cable bush at the bottom as shown in the figure. ! INSTALLATION & CONNECTION J ` Use an appropriate cable bush for the LAN cable to be connected. - Basic camera : Use the cable with a diameter of Ø5~6.5. 3.
installation & connection Attaching to the unbundled adapter Outdoor installation Choose and purchase a necessary one of the following options (unbundled) that is suitable to the installation site or for your convenience. When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside. 1.
Adjusting the monitoring direction for the camera (QND-7012R/7022R/7032R/7082R, QNV-6014R/7012R/7022R/7032R/6084R/7082R) INSERTING/REMOVING A MICRO SD CARD J Pan ` Before installing the camera, the Micro SD card should be inserted while the power source and the body are separated. ` Do not forcefully insert it in the reverse direction. It might damage your Micro SD card and your product.
Inserting a Micro SD card (QND-7012R/7022R/7032R/7082R, QNV-6014R/7012R/7022R/7032R/6084R/7082R) 1. Separate the Dome cover of the camera. 2. Insert a Micro SD card in the arrow direction shown in the figure. NET WO ACT RK LINK 12 FR ON T FR ON T RESET 3 4 5 1. AL 2. M AL 3.
Removing a Micro SD card Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot.
installation & connection J ` Before removing the Micro SD card, in --, set the device to and press the [Apply] button and turn the camera off. ` If you turn off the camera or remove the Micro SD card that contains data from the product, the data may be lost or damaged. NET WO ACT RK LINK RESET 12 1. AL 2. M AL 3.
POWERING AND NETWORKING J ` Before plugging the DC 12 V power plug into the outlet, please assemble the terminal block first. ! INSTALLATION & CONNECTION NE ACT TWOR LINK K AC NE T LINK TW ORK NE AC TWO T LI RK NK RM LA RM IN UT O LINK ACT 2 RESET 1 AALA VIDEO Power 4 5 GN D 1. ALM ALM IN 2. ALM IN OUT ALM 3.2.AUDIO OU INT NETWORK 3. 4.
installation & connection Ethernet Connection Connecting to Audio Input Connect the Ethernet cable to the local network or to the Internet. Speaker Power Supply PC Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the camera. J Network ` If both PoE and DC 12V are applied simultaneously, the product will be supplied with power from DC 12V. - You can also use a router featuring PoE to supply power to the camera.
Connecting to the I/O port box Connect the Alarm I/O cable to the corresponding port of the port box. CAUTION:Be ware of the Rated Voltage and Polarity of the power connection. ! INSTALLATION & CONNECTION Alarm (Warning lamp) Sensor NE AC TWOR T LI K NK VIDEO D 4 5 GN 1. ALM IN 2. ALM OUT 3. AUDIO IN RESET Sensor FR ON T DC 12 V Alarm (Warning lamp) 1.AL 2.AL M IN 3.4. M O 5.
installation & connection ~ ALARM-IN : Used to connect the alarm input sensor or external day/night sensor. ~ ALARM-OUT : Used to connect the alarm output signal. ~ GND : Common port for alarm in/output signal. J Alarm In Wiring Diagram External connection Inside of the camera VCC_3.3V ` If devices (e.g., flashing light and siren) that exceed the voltage and current specifications are connected by using the open collector method, it may cause malfunction.
network connection and setup You can set up the network settings according to your network configurations. CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE MODEM INTERNET 1. Launch an Internet browser on the local PC. DSL/Cable Modem 2. Enter the IP address of the camera in the address bar of the browser. Camera External Remote PC DDNS Server (Data Center, KOREA) Camera 1. Connect the user PC directly with the network camera.
network connection and setup USING DEVICE MANAGER M ` Device manager program can be downloaded from - menu at Hanwha Techwin website (http://www.hanwha-security.com). ` More instructions of Device Manager can be found at menu of the main page. AUTOMATICALLY SEARCHING CAMERA If using a Broadband Router ~ IP Address : Enter an address falling in the IP range provided by the Broadband Router. ex) 192.168.1.2~254, 192.168.0.2~254, 192.168.XXX.
Configuring Dynamic IP Receive IP address from DHCP ~ Example of the Dynamic IP environment - If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server AUTOMATICALLY CONFIGURING IP 1. Click the camera from the list that you want to automatically configure the IP. - If IPs are assigned by the internal DHCP server via the LAN 3. At the menu, click . 1. Click the camera from the list that you want to change the IP setting.
network connection and setup PORT RANGE FORWARD (PORT MAPPING) SETUP Setting up Port Range Forward for several network cameras If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the Broadband Router so that a remote PC can access the camera in it. ~ You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page. ~ A user can change each port using the camera setting screen.
CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 1. Run device manager. It will scan for connected cameras and display them as a list. M ! NETWORK CONNECTION AND SETUP 2. Double-click a camera to access. The Internet browser starts and connects to the camera. ` Access to the camera can also be gained by typing the camera’s IP address in the address bar of the Internet browser.
web viewer CONNECTING TO THE CAMERA Normally, you would 1. Launch the Internet browser. Type the IP address of the camera in the address bar. ex) • IP address (IPv4) : 192.168.1.100 ; http://192.168.1.100 - the Login dialog should appear. • IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111 ; http://[2001:230:abcd:ffff:0000:0000:ffff:1111] - the Login dialog should appear. If the HTTP port is other than 80 1. Launch the Internet browser.
PASSWORD SETTING When you access the product for the first time, you must register the login password. ` For a new password with 8 to 9 digits, you must use at least 3 of the following: uppercase/lowercase letters, numbers and special characters. For a password with 10 to 15 digits, you must use at least 2 types of those mentioned. - Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].?/ 1. Click the [Setup ( )] icon. 2. The Settings window appears. 3.
appendix TROUBLESHOOTING PROBLEM SOLUTION PROBLEM When an Windows 10 user accesses the web viewer through Chrome or Firefox, the sound volume of microphone changes periodically. ~ This is what happens when microphone driver has been set to Realtek driver. Install the High Definition Audio device (Windows Default Driver) or the third party driver as the microphone driver. of is set to , but no notification e-mail reaches me even when an analysis event had occurred.
Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
