AW-SEMTransform(RF267,2#3957D82009.8.204:49PM페이지1 in REFRIGERATOR MODEL NAME : RF267AE** RF26XAE** MODEL CODE : RF267AERS/XAA RF267AEPN/XAA RF267AEBP/XAA RF267AEWP/XAA RF26XAERS/XAA RF26XAEPN/XAA REFRIGERATOR CONTENTS 1. PRECAUTIONS(SAFETY WARNINGS) · 4 2. PRODUCT SPECIFICATIONS ········ 3. DISASSEMBLY AND REASSEMBLY ·· 8 20 4. TROUBLESHOOTING ···············46 5 . EXPLODED VIEW & PARTS LIST ···· 83 6. PCB DIAGRAM ··················· 105 7. WIRING DIAGRAM ················ 111 8.
AW-SEMTransform(RF267,2#3957D82009.8.204:49PM페이지3 in WARNING IMPORTANT SAFETY NOTICE The service guide is for service men with adequate backgrounds of electrical, electronic, and technician experience. Any attempt to repair a major appliance may result in personal injury and property damage. The manufacturer or dealer cannot be responsible for the interpretation of this information. SAMSUNG ELECTRONICS AMERICA, INC. Technical Service Guide Copyright ⓒ2009 All rights reserved.
AW-SEMTransform(RF267,2#3957D82009.8.204:49PM페이지4 in Contents 1. PRECAUTIONS(SAFETY WARNINGS) ··············································4 2.
AW-SEMTransform(RF267,2#3957D82009.8.204:49PM페이지5 in Contents 4-2) DIAGNOSTIC METHOD ACCORDING TO THE TROUBLE SYMPTOM(FLOW CHART) ············57 4-2-1. IF THE TROUBLE IS DETECTED BY SELF-DIAGNOSIS ····························58 4-2-2. IF FAN DOES NOT OPERATE(F, R, C - FAN) ···································68 4-2-3. IF ICE ROOM FAN DOES NOT OPERATE ·····································69 4-2-4. IF ICE MAKER DOES NOT OPERATE ········································70 4-2-5.
AW-SEMTransform(RF267,2#3957D82009.8.204:49PM페이지4 in 1. PRECAUTIONS(SAFETY WARNINGS) ● Before servicing the refrigerator or replacing parts, unplug the unit from the wall outlet. → Shock Hazard, observe basic safety rules. ● Be sure to use the specified generic parts when servicing the product. → Confirm the Model Number on Product itself. Inspect the mew part and assembly for Voltage, Current and temperature specifications.
AW-SEMTransform(RF267,2#3957D82009.8.204:49PM페이지5 in PRECAUTIONS(SAFETY WARNINGS) Read all instructions before repairing the product and follow the instructions in order to prevent danger or property damage. CAUTION/WARNING SYMBOLS DISPLAYED Warning SYMBOLS means “Prohibited”. Indicates that a danger of death or serious injury exists. means “Do not disassemble”. means “No contact”. means ”Warning or Caution”. Caution Indicates that a risk of personal injury or material damage exists.
AW-SEMTransform(RF267,2#3957D82009.8.204:49PM페이지6 in PRECAUTIONS(SAFETY WARNINGS) ❈ Please let users know following warnings & cautions in detail. Warning & Caution Do not allow users to put bottles or kinds of glass in the freezer. Do not allow users to store narrow and lengthy bottles or foods in a small multi-purpose room. Do not allow users to store pharmaceutical products, scientific materials, etc., in the refrigerator. ●Freezing of the contents may inflict a wound.
AW-SEMTransform(RF267,2#3957D82009.8.204:49PM페이지7 in PRECAUTIONS(SAFETY WARNINGS) FLOORING For proper installation, this refrigerator must be placed on a level surface of hard material that is the same height as the rest of the flooring. This surface should be strong enough to support a fully loaded refrigerator, or approximately 660lbs(299kg). MOVING Protect the finish of the flooring. Cut a large section of the cardboard carton and place under the refrigerator where you are working.
AW-SEMTransform(RF267,2#3957D82009.8.204:49PM페이지8 in 2.
AW-SEMTransform(RF267,2#3957D82009.8.204:49PM페이지9 in 2. PRODUCT SPECIFICATIONS 2-1) Introduction of main function ● A newly Developed SAMSUNG bottom mount freezer in 2009 has the following characteristics. Surround Multi Flow ● Uniform cooling for each shelf and even in corner in fresh food compartment by centerpositioned fan and duct with multiple flow effluences Twin Cooling System ● The refrigerator and the freezer have two evaporators.
AW-SEMTransform(RF267,2#3957D82009.8.204:50PM페이지10 in PRODUCT SPECIFICATIONS 2-2) Specifications ELECTRICAL SPECIFICATIONS Defrost Control From 24 to 32 hrs Thermo Bimetal Protector 140°F(60℃)(off) 104°F(40℃)(on) Defrost Thermistor(502AT) 50°F(10℃)(off) Electrical Rating AC115V 60Hz 11.6 Amps Maximum Current Leakage 0.25 mA Maximum Ground Path Resistance 0.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.204:50PM페이지13 in PRODUCT SPECIFICATIONS 2-4) Model Specification & Specification Chart ITEM Model RF267 / RF26X W 35 3/4 inch (908mm) 29 1/8 inch (740mm) D External size H Net Capacity 35 5/8 inch (905mm) W/O Hinge Cap 68 5/8 inch (1744mm) With Hinge Cap 70 Inch (1778mm) Total 26 Cu.ft (733.4ℓ) Freezer 8.2 Cu.ft(232.2ℓ) Refrigerator 17.7 Cu.ft(501.2ℓ) Efficiency of volume Weight 50.
AW-SEMTransform(RF267,2#3957D82009.8.204:50PM페이지14 in PRODUCT SPECIFICATIONS Specification Model RF267 / RF26X Compressor Components for Freezer Defrost Sensor Defrost Cycle Refrigerator Freezer Evaporator Bimetal Room Temperature Sensor Components Defrost Related Components Items Model BK190CL2C/E02 Starting type R.S.C.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.204:50PM페이지16 in PRODUCT SPECIFICATIONS 2-6)Dimensions of Refrigerator 35 5/8"(905mm) 32 29/32"(836mm) 1/5"(5mm) 70"(1778mm) 3 3/8"(86mm) 19/32"(15mm) 24 9/32"(617mm) 41 11/16"(1059mm) 1.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.204:50PM페이지20 in 3.
AW-SEMTransform(RF267,2#3957D82009.8.204:50PM페이지21 in ASSEMBLY & DISASSEMBLY 3-1) PRECAUTION • Unplug the refrigerator before cleaning and making repairs. • Remove any foreign matter or dust from the power plug pins. - Otherwise there is a risk of fire. • Do not use a cord that shows cracks or abrasion damage along its length or at either end. • Do not plug several appliances into the same multiple power board.
AW-SEMTransform(RF267,2#3957D82009.8.204:50PM페이지22 in DISASSEMBLY AND REASSEMBLY 3-2) Refrigerator Door Part Name How To Do Descriptive Picture 1. With the door opened, remove the Top Table cap(1⃞) with a Flat head screwdriver, and close the door. Refrigerator Door 1⃞ 2. Remove the 3 screw holding down the Top Table and remove the Top Table(2⃞). 2⃞ 3. Disconnect a earth wire(3⃞), electronic connector(4⃞) and a water(5⃞)coupling .
AW-SEMTransform(RF267,2#3957D82009.8.204:50PM페이지23 in DISASSEMBLY AND REASSEMBLY Part Name How To Do Descriptive Picture 5. Lift the door straight up to remove. Refrigerator Door [12] 6.Remove 2 hex head bolts( 7⃞ ) with 5mm Allen Wrench(3/16") and an screw( 8⃞ ) with Philips screwdriver.
AW-SEMTransform(RF267,2#3957D82009.8.204:50PM페이지24 in DISASSEMBLY AND REASSEMBLY 3-3) Door Handle Part Name How To Do Descriptive Picture 1. Remove the Cap Door with a flat-blade(-) screwdriver. Door Handle Freezer 2. Remove 4 screws 3. Lift up the handle to have the Slider Handle Fre(1⃞) pushed back. 4. After having the Slider Handle Fre(1⃞) pushed back, screw up at the hole. 5. Remove the door handle by lifting it up.
AW-SEMTransform(RF267,2#3957D82009.8.204:51PM페이지25 in DISASSEMBLY AND REASSEMBLY 3-4) Refrigerator Light Part Name How To Do Descriptive Picture 1. Remove the lamp cover by pulling it down as pushing the rear of lamp cover. Refrigerator Light 2. Remove the screw. And separate the LED panel. 3-5) Cover-display & water-dispenser Part Name How To Do Descriptive Picture 1. Insert a flat-blade screwdriver on the slot as shown in the picture, and unlock the tabs. Cover-display 2.
AW-SEMTransform(RF267,2#3957D82009.8.204:51PM페이지26 in DISASSEMBLY AND REASSEMBLY Part Name Cover-display How To Do Descriptive Picture 4. Remove 4 screws of coverdisplay 3-6) Water-dispenser Part Name How To Do 1. Disengage the 3 Housing Connect. 2. Remove 2 screws of the CaseIce,Route Assy. Water-dispenser 3. Pull the Case-Ice,Route Assy. 4. Push the hook and remove the Micro Switch.
AW-SEMTransform(RF267,2#3957D82009.8.204:51PM페이지27 in DISASSEMBLY AND REASSEMBLY Part Name How To Do Descriptive Picture 1. Assembly shall be the contrary order from the disassemble. Case-Ice and Route shall be assembled inside of hose. Otherwise, assemble cannot be accomplished. Water-dispenser 2. When assembling CoverDisplay, first insert it from leftside and then assemble to rightside. Otherwise, the tab can be broken.
AW-SEMTransform(RF267,2#3957D82009.8.204:51PM페이지28 in DISASSEMBLY AND REASSEMBLY 3-8) Foldable Glass Shelf Part Name Foldable Glass Shelf How To Do Descriptive Picture Remove 2 screws of the Fold Glass Shelf 3-9) Vegetable & Fruit Drawers Shelf Part Name How To Do 1. Remove the vegetable & fruit drawer by pulling the roller part and lifting it up. Vegetable & Fruit Drawers Shelf 2. Remove the vegetable & fruit drawers shelf by pulling it out.
AW-SEMTransform(RF267,2#3957D82009.8.204:51PM페이지29 in DISASSEMBLY AND REASSEMBLY 3-10) Cool Select Pantry Part Name How To Do 1. Remove the cool select pantry by pulling the roller part and Cool Select Pantry lifting it up. Cool Select Pantry Cover 1. Remove the cool select pantry cover by lifting the central part of the cover while pushing it to the left. Cool Select Pantry 1. Remove the cool select pantry shelf by lifting the front part of Shelf the shelf while pulling it. 1.
AW-SEMTransform(RF267,2#3957D82009.8.204:51PM페이지30 in DISASSEMBLY AND REASSEMBLY 3-11) Water Tank Part Name How To Do The Water Tank is located in the lower part of the fridge. Before disassembling the Water Tank take out shelf and drawers and pantry located in front of the Water Tank. 1. Remove 2 screw of the Water Tank cover. Water Tank 2. Disengage the housing connector. One water Tube is located in the machine compartment of the refrigerator.
AW-SEMTransform(RF267,2#3957D82009.8.204:51PM페이지31 in DISASSEMBLY AND REASSEMBLY Part Name How To Do 6. Disconnect the water tube by pushing the tube fitting apart as shown in the picture. Water Tank The other Water Tube is located in the Top Table of the refrigerator. Before disassembling the Water Tube, take out the Top table. 7. Remove the blue cap of water coupler with other tools. 8. Disconnect the water coupler by pushing as shown in the picture. 9.
AW-SEMTransform(RF267,2#3957D82009.8.204:51PM페이지32 in DISASSEMBLY AND REASSEMBLY 3-12) Motor Damper Part Name How To Do Descriptive Picture 1. Remove the cool select pantry. Remove the screw part of lower motor damper part and then push the motor damper down. Motor Damper 2. Disengage 2 housing connectors from the rear motor damper. (Refer to the picture) 3-13) Water Filter (Disassembly) Part Name How To Do 1. Remove the shelf by lifting the front plane of the shelf up and pulling it out.
AW-SEMTransform(RF267,2#3957D82009.8.204:52PM페이지33 in DISASSEMBLY AND REASSEMBLY 3-14) Water Filter (Reassembly) Part Name How To Do Descriptive Picture 1. Place the part of (ⓐ) arrow (that is indicating in the picture) in the middle of the front filter cover and push it up. Water Filter 2. Turn the water filter counterclockwise until central horizontal line of filter cover and both ends of water filter label are made all of the same width. (Refer to the picture.
AW-SEMTransform(RF267,2#3957D82009.8.204:52PM페이지34 in DISASSEMBLY AND REASSEMBLY 3-16) Vertical Hinged Section Part Name How To Do 1. Remove 2 screw cap parts with a flat-blade(-) screwdriver. (Refer to the picture) 2. Unscrew 2 screws. Vertical Hinged Section 3. Disengage the internal housing connector of the vertical hinge. 4. Remove the vertical hinged section by lifting the vertical hinge up.
AW-SEMTransform(RF267,2#3957D82009.8.204:52PM페이지35 in DISASSEMBLY AND REASSEMBLY 3-17) Evaporator Cover In Refrigerator Part Name How To Do Descriptive Picture 1. Remove the angle cap with a flat-blade screwdriver. (Refer to the picture) 2. Unscrew 4 screws. Evaporator Cover In Refrigerator 3. Remove the the lower part of angle mid by pulling it out and pushing it down. (Refer to the picture) 4. Remove the hook by pulling it from the lower part and pushing the cover down. (Refer to the picture) 5.
AW-SEMTransform(RF267,2#3957D82009.8.204:52PM페이지36 in DISASSEMBLY AND REASSEMBLY 3-18) Evaporator In Refrigerator Part Name How To Do 1. Remove the the housing cover by pushing both lateral sides of the housing cover and pulling it out. (Refer to the picture) 2. Disconnect the housing connector part. (Refer to the picture) Evaporator In Refrigerator 3. Unscrew 2 screws. 4. Remove the evaporator by lifting the bottom side of it up and pulling it out.
AW-SEMTransform(RF267,2#3957D82009.8.204:52PM페이지37 in DISASSEMBLY AND REASSEMBLY 3-19) Freezer Door Part Name How To Do 1. Open the freezer door. Remove the tilting pocket by pushing it to the left. (Refer to the picture) 2. Remove the 2 support tilting pockets with temporary force. (Refer to the picture) Freezer Door 3. Remove the freezer drawer bin by lifting the bottom part of it up. (Refer to the picture) 4. Remove 4 internal bolts at both lateral sides of rail part. (Refer to the picture) 5.
AW-SEMTransform(RF267,2#3957D82009.8.204:52PM페이지38 in DISASSEMBLY AND REASSEMBLY 3-20) Pull Out Drawer Part Name How To Do 1. Slide the drawer in as much as possible Door Handle Freezer 2. Lift the drawer up 3. Remove the pull out drawer by lifting the bottom part of drawer bin and pulling it out.
AW-SEMTransform(RF267,2#3957D82009.8.204:52PM페이지39 in DISASSEMBLY AND REASSEMBLY 3-21) Ice-Maker Part Name How To Do Descriptive Picture lever lever lever lever lever 1. Pull the Ice-Bucket lever and out 2. Remove 1 screw of the Cover 3. Disassemble the cover with a flat-blade(-) screwdriver and pull it out. Ice Maker 4. Disengage the 2 housing connector. 5. Push hook and pull the IceMaker out. 6. To disassemble, push the tab and pull the case-auger and the motor out.
AW-SEMTransform(RF267,2#3957D82009.8.204:52PM페이지40 in DISASSEMBLY AND REASSEMBLY 3-22) Freezer Light Part Name How To Do Freezer Light 1. Remove the light by pulling the light cover down while pushing the rear plane of light cover. Descriptive Picture 3-23) Door Switch In Freezer Part Name How To Do 1. Remove the freezer drawer bin by using a flat-blade(-) screwdriver.(Refer to the picture) Door Switch In Freezer 2. Disconnect the housing connector part.
AW-SEMTransform(RF267,2#3957D82009.8.204:52PM페이지41 in DISASSEMBLY AND REASSEMBLY 3-24) Evaporator Cover In Freezer Part Name How To Do Descriptive Picture 1. Remove the freezer door and freezer drawer bin by pulling out the drawer and then unscrewing 2 screws. Evaporator Cover In Freezer 2. Lift up the evaporator cover. 3. Disengage the 3 housing connector and remove the evaporator cover. 3-25) Evaporator In Freezer Part Name How To Do 1.
AW-SEMTransform(RF267,2#3957D82009.8.204:53PM페이지42 in DISASSEMBLY AND REASSEMBLY 3-26) Machine Compartment Part Name How To Do 1. Unscrew 5 screws of cover compressor. 2. Disengage the housing connector. (Refer to the picture) 3. Remove the hooker of support circuit motor by lifting the hooker up and pulling it out. Motor Fan 4. Remove the spring with a flatblade screwdriver. (Refer to the picture) 5. Remove the motor fan by pulling the fan out while grasping the motor part.
AW-SEMTransform(RF267,2#3957D82009.8.204:53PM페이지43 in DISASSEMBLY AND REASSEMBLY Part Name How To Do 1. Disengage the housing connector. Relay O/L 2.Remove Cover Relay 3. Remove the relay O/L with a flat-blade screwdriver. (Refer to the picture) 1. Unscrew the water valve fixed by the screw. 2. Remove the the hook part of the hose by pushing it down. Water Valve 3. Remove 2 water hose parts while pushing the upper part of ①. (Refer to the picture) 4. Disengage 2 housing connector parts. 5.
AW-SEMTransform(RF267,2#3957D82009.8.204:53PM페이지44 in DISASSEMBLY AND REASSEMBLY Part Name How To Do 1. Unscrew 2 screws. 2. Disengage the housing connector. Power Cord & Noise Filter 3. Unscrew 2 earth screws. 4. Remove the cover by pushing the hook up using a flat screwdriver. (Refer to the picture) 5. Disengage the housing connector to separate the power cord and noise filter.
AW-SEMTransform(RF267,2#3957D82009.8.204:53PM페이지45 in DISASSEMBLY AND REASSEMBLY 3-27) Electric Box Part Name How To Do 1. Pull the refrigerator forward to have enough space to work on the rear side of the appliance. 2. Unscrew 2 screws for the PCB cover. PBA Main 3. Disengage all housing connectors connected with PBA MAIN. 4. Remove the PBA MAIN while lifting the upper part of the hook up. (Refer to the picture) PBA INVERTER 1. Remove cover and the all connectors on the PBA MAIN.
AW-SEMTransform(RF267,2#3957D82009.8.204:53PM페이지46 in 4. TROUBLESHOOTING 4-1) FUNCTION FOR FAILURE DIAGNOSIS ······················47 4-1-1. TEST MODE (MANUAL OPERATION / MANUAL DEFROST FUNCTION) 4-1-2. DISPLAY FUNCTION OF COMMUNICATION ERROR 4-1-3. SELF-DIAGNOSTIC FUNCTION 4-1-5. EXHIBITION MODE SETTING FUNCTION 4-1-7. OPTION TABLE ·····················48 ··································49 4-1-4. DISPLAY FUNCTION OF LOAD CONDITION 4-1-6.
AW-SEMTransform(RF267,2#3957D82009.8.204:53PM페이지47 in TROUBLESHOOTING 4-1) Function for failure diagnosis 4-1-1. Test mode (manual operation / manual defrost function) If Energy Saver Key + Fridge Key on the front of panel are pressed simultaneously for 8 seconds, it will be changed to the test mode and all displays on the front of panel will be off.
AW-SEMTransform(RF267,2#3957D82009.8.204:53PM페이지48 in TROUBLESHOOTING 2) Simultaneous manual defrost(fresh food and freezer compartments) function 2-1) If any key is pressed one more time during manual operation(fresh food compartment), "Fd" shows in the display and then manual operation will be canceled at once and fresh food and freezer compartment will be defrosted. 2-2) At this moment, alarm beeps for 3 seconds (0.
AW-SEMTransform(RF267,2#3957D82009.8.204:53PM페이지49 in TROUBLESHOOTING 4-1-3. Self-diagnostic function 1) Self-diagnostic function in the Initial power ON 1-1) Micom operates self-diagnostic function to check the temperature sensor condition within 1 second when the refrigerator turned On initially. 1-2) If bad sensor is detected by the self-diagnostic function, the applicable display LED will blink for 0.5 sec. At this moment, there is no beep sound.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.204:53PM페이지51 in TROUBLESHOOTING Self-diagnostics check list LED Item Trouble contents R-1-ⓐ Ice Maker Sensor Error R-1-ⓑ R-Sensor Error When checking the voltage of MAIN PCB CN30#6↔CN76#1: should be between 4.5V~1.
AW-SEMTransform(RF267,2#3957D82009.8.204:53PM페이지52 in TROUBLESHOOTING 4-1-4. Display function of Load condition ① ① 2¢ (-17¡ ) is recommended 38¢ (3¡ ) is recommended ② ① If Energy Saver Key + Alarm/Lighting key are pressed simultaneously for 6 seconds, ALL ON/OFF will blink with 0.5interval for 2 seconds. ② If take the finger off from above keys and press Fridge/Power Cool Key, load condition mode will be started.
AW-SEMTransform(RF267,2#3957D82009.8.204:53PM페이지53 in TROUBLESHOOTING 4-1-5. Cooling off mode setting function ① 2¢ (-17¡ ) is recommended 38¢ (3¡ ) is recommended ① ① If Energy Saver Key + Power Freeze Key are pressed for 3 seconds, Cooling off mode will be started. 1) If Energy Saver Key + Freezer/Power Freeze are pressed simultaneously for 3 seconds during normal operation, Cooling off mode will be started with buzzer sound(ding-dong).
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.204:53PM페이지55 in TROUBLESHOOTING 2) After changing to the option mode, fresh food compartment "0" , freezer compartment "0" will be displayed. ( Basically fresh food compartment "0", freezer "0" would be set at shipping process, but setting value could be changed for the purpose of improving product at mass producing process.
AW-SEMTransform(RF267,2#3957D82009.8.204:53PM페이지56 in TROUBLESHOOTING 4-1-7. Option TABLE 1) Temperature changing table of freezer compartment Set item Freezer Temp Shift MODEL RF267/RF26V Reference Value Fridge Room 7-SEG 0 Setting value FZ compartment Code Temp. compensation 0 0 1 - 1℉(-0.5°C) 2 - 2℉(-1.0°C) 3 - 3℉(-1.5°C) 4 - 4℉(-2.0°C) 5 - 5℉(-2.5°C) 6 - 6℉(-3.0°C) 2¢ (-17¡ ) is recommended 7 - 7℉(-3.5°C) 8 + 1℉(+0.5°C) 9 + 2℉(+1.0°C) 10 + 3℉(+1.5°C) 11 + 4℉(+2.
AW-SEMTransform(RF267,2#3957D82009.8.204:53PM페이지57 in TROUBLESHOOTING 4-2) Diagnostic method according to the trouble symptom(Flow Chart) DATA1.Temperature table Resistance value and MICOM port voltage of sensor according to the temperature SENSOR CHIP : based on PX41C ℃ ℉ -50 -49 -48 -47 -46 -45 -44 -43 -42 -41 -40 -39 -38 -37 -36 -35 -34 -33 -32 -31 -30 -29 -28 -27 -26 -25 -24 -23 -22 -21 -20 -19 -18 -17 -16 -15 -14 -13 -12 -11 -10 -9 -8 -7 -6 -58 -56.2 -54.4 -52.6 -50.8 -49 -47.2 -45.4 -43.6 -41.
AW-SEMTransform(RF267,2#3957D82009.8.204:53PM페이지58 in TROUBLESHOOTING 4-2-1. If the trouble is detected by self-diagnosis - The error of sensor will be displayed on the front of display. when the error of sensor is detected at initial power ON, the appliance will not operated and display of abnormal sensor part will blink. - The appliance will not stop operating when the error of sensor is detected during operation of the appliance.
AW-SEMTransform(RF267,2#3957D82009.8.204:53PM페이지59 in TROUBLESHOOTING 2) If R Sensor has trouble ERROR Code 2¢ (-17¡ ) is recommended 38¢ (3¡ ) is recommended Start DATA1.
AW-SEMTransform(RF267,2#3957D82009.8.204:53PM페이지60 in TROUBLESHOOTING 3) If R DEF Sensor has trouble ERROR Code 2¢ (-17¡ ) is recommended 38¢ (3¡ ) is recommended Start DATA1.
AW-SEMTransform(RF267,2#3957D82009.8.204:53PM페이지61 in TROUBLESHOOTING 4) If Ambient Sensor has trouble ERROR Code 2¢ (-17¡ ) is recommended 38¢ (3¡ ) is recommended Start DATA1. Temperature table ** Measuring point of resistance value according to Sensor ** Ambient : CN31#1 ↔ #4 measuring resistance value ** Placed in the right top table of upper hinge.
AW-SEMTransform(RF267,2#3957D82009.8.204:53PM페이지62 in TROUBLESHOOTING 5) If F Sensor has trouble ERROR Code 2¢ (-17¡ ) is recommended 38¢ (3¡ ) is recommended Start DATA1.
AW-SEMTransform(RF267,2#3957D82009.8.204:53PM페이지63 in TROUBLESHOOTING 6) If F DEF Sensor has trouble ERROR Code Start DATA1.
AW-SEMTransform(RF267,2#3957D82009.8.204:54PM페이지64 in TROUBLESHOOTING 7) If Ice Room Sensor has trouble ERROR Code 2¢ (-17¡ ) is recommended 38¢ (3¡ ) is recommended Start DATA1.
AW-SEMTransform(RF267,2#3957D82009.8.204:54PM페이지65 in TROUBLESHOOTING 8) If Pantry Sensor has trouble ERROR Code 2¢ (-17¡ ) is recommended 38¢ (3¡ ) is recommended Start DATA1.
AW-SEMTransform(RF267,2#3957D82009.8.204:54PM페이지66 in TROUBLESHOOTING 9) If Pantry Room Damper Heater has trouble ERROR Code 2¢ (-17¡ ) is recommended 38¢ (3¡ ) is recommended Start Measure the resistance between ①-② after CN91 connector open 145ohm ± 7% NO Is Damper Heater normal?(about145ohm) YES Replace Damper NO Is MAIN PCB connector (CN91) inserted correctly? Bad contact of connector/ insert correctly YES Initial Damper Damper power On heater off heater On MICOM #42 condition 3.5V~4.8V 3.
AW-SEMTransform(RF267,2#3957D82009.8.204:54PM페이지67 in TROUBLESHOOTING 10) If Tank Water Heater has trouble ERROR Code Start Measure the resistance between #6~#10 after CN79 connector open 72ohm ± 7% Is MAIN PCB connector (CN79) inserted correctly? NO YES Is Tank Water Heater normal?(about72ohm) NO YES MICOM Initial power On Heater off Working heater #6 3.5V~4.8V 3.5V~4.
AW-SEMTransform(RF267,2#3957D82009.8.204:54PM페이지68 in TROUBLESHOOTING 4-2-2. If FAN does not operate(F, R, C - FAN) - The refrigerator of this model has BLDC FAN motor. BLDC motor is driven by DC 7~12V. - On the normal condition of COMP ON, it operates together with F-FAN motor. If door is opened and closed once at a high ambient temperature, it will be operated after 1 minute delay. Therefore, you are advised not to taken it for an error. -.
AW-SEMTransform(RF267,2#3957D82009.8.204:54PM페이지69 in TROUBLESHOOTING 4-2-3. If ICE Room Fan does not operate - This refrigerator has BLDC FAN motor. BLDC motor is driven by DC7~12V. - When COMP ON, normally operates with F-FAN motor. - If there is any trouble, you should select the self-diagnostic function to check the trouble before power off. Start - When pressing the ICE TEST S/W for a certain period of time (over 1.5sec), the function is accomplished.
AW-SEMTransform(RF267,2#3957D82009.8.204:54PM페이지70 in TROUBLESHOOTING 4-2-4. If Ice Maker does not operate 1. Water is automatically supplied to the Ice Maker depending on temperature & time condition and Ice Maker Dispenses cubed or crushed ice. 2. Power is applied to the one end of wires. Be careful when disassembling and shall refer to its exploded diagram in any case. 3. Ice Maker operation shall be checked after pressing the Ice Maker testing switch.
AW-SEMTransform(RF267,2#3957D82009.8.204:54PM페이지71 in TROUBLESHOOTING 4-2-5. If defrost does not operate (F,R DEF Heater) - If defrost has trouble, select the self-diagnostic function to detect the error of defrost heater before Power Off.
AW-SEMTransform(RF267,2#3957D82009.8.204:54PM페이지72 in TROUBLESHOOTING 4-2-6. If Power is not supplied Caution At the power of main PCB, the AC115V power and a high-voltage over DC 170V are occurred.Please take care of yourself during repair and measurement.
AW-SEMTransform(RF267,2#3957D82009.8.204:54PM페이지73 in TROUBLESHOOTING 4-2-7. If compressor does not operate Start Did 7 mins pass after Compressor OFF ? Check after 7minutes Refer to test function in the manual Does compressor work with manual operation? Did buzzer of manual operation sound? (Check certainly after manual operation) normal Is IC02 MICOM #8 High?(5V) 1) Replace MICOM 2) Replace PCB Is IC72 #15 about 0.
AW-SEMTransform(RF267,2#3957D82009.8.204:54PM페이지74 in TROUBLESHOOTING 4-2-8. When alarm sound continuous without stop(related with buzzer sound) ① If 'ding-dong'sound continuously Start Is door closed completely? Door is ajar Remove causes after comprehending the conditions of interferance by door gasket, food etc, Is water penetrated into the door switch? Replace Door S/W Seperate the door switch andcheck if the measured value of unit is changed from 0Ω to ∞Ω according to switch ON/OFF.
AW-SEMTransform(RF267,2#3957D82009.8.204:54PM페이지75 in TROUBLESHOOTING ③ If buzzer does not sound Buzzer is installed on the panel PCB in this model. If buzzer does not sound when button is pressed, manual operation is started and door is opened, should separate panel PCB and check the breakage of buzzer and bad soldering. It is very hard to repair the panel PCB because it consists of SMD assemblies.
AW-SEMTransform(RF267,2#3957D82009.8.204:54PM페이지76 in TROUBLESHOOTING 4-2-9. If Panel PCB does not work normally ① When lighting of Panel PCB is disabled or only some LED Lamp are disabled Be careful to repair because display of this model is installed in the MICOM of internal PCB. It is recommend to replace PCB MAIN after checking except specified solder touch.
AW-SEMTransform(RF267,2#3957D82009.8.204:54PM페이지77 in TROUBLESHOOTING 4-2-10. If Pantry Panel PCB is not working normally You should check the display after door opening because the display of this model operates only when the fresh food compartment door is opened.
AW-SEMTransform(RF267,2#3957D82009.8.204:54PM페이지78 in TROUBLESHOOTING 4-2-11. When refrigerator ROOM Lamp does not light up 1. When you replace the lamp of freezer, please power OFF to avoid an electric shock. 2. Please keep in mind you could get burnt by the excessive heating of an incandescent light bulb. 3. Bimetal is installed in the refrigerator LAMP. Check that if LAMP may be turned OFF by bimetal. 1) AC Lamp (Option) ※ We only explaine about Fresh Food compartment in this page.
AW-SEMTransform(RF267,2#3957D82009.8.204:54PM페이지79 in TROUBLESHOOTING 4-2-12. If ICE Water is not supplied 1. Please shut the water supplying prior to repair. 2. Power is applied to the one end of wires. Be careful when disassembling not to get an electric shock.
AW-SEMTransform(RF267,2#3957D82009.8.204:55PM페이지80 in TROUBLESHOOTING 4-2-13. If Water is not supplied Start ☞ Checking method of Valve resistance (Must power off for checking) Resistance can be changed by input voltage. CN70#1 (Red) ↔ CN73#5 (White-black) - resistance value ; 388(1.
AW-SEMTransform(RF267,2#3957D82009.8.204:55PM페이지81 in TROUBLESHOOTING 4-2-14. If Cubed or Crushed Ice is not supplied Freezer door shall be closed during operation.
AW-SEMTransform(RF267,2#3957D82009.8.204:55PM페이지82 in TROUBLESHOOTING 4-2-15. If Cover Ice Route Moor(Geard Motor) is not working normally Caution 1. When replacing the Cover Ice Motor, pull out the plug to avoid an electric shock. 2. Be careful! When disassemble the Cover Ice Motor, spring can jumped out and may cause personal injury. 3. Motor will rotate continuously when the Motor Switch is not sensed.
AW-SEMTransform(RF267,2#3957D82009.8.204:55PM페이지83 in 5 .
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.204:55PM페이지86 in EXPLODED VIEW& PARTS LIST ■ Parts List of Freezer NO CODE-NO 17-1 17-2 17-3 17-4 18 19 20 20-1 20-2 6002-000213 DA61-04824A DA63-04618A DA63-04313A DA34-10120E DA61-04796A DA97-02019B DA63-10467B DA32-00011U PART NAME SCREW-TAPPING REINF-DRAWER BOX TRAY-DRAWER BOX GROMMET-TRAY DRAWER BOX SWITCH DOOR-F GUIDE-DRAWER BOX ASSY COVER-SENSOR COVER-SENSOR SENSOR TEMP SPEC TH,+,1,M4,L12,ZPC(WHT),SWRCH18A AW-PJT,SHP1,T2.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.204:56PM페이지103 in 6.
AW-SEMTransform(RF267,2#3957D82009.8.204:56PM페이지104 in PCB DIAGRAM 6-1) PCB Layout with part position 1. DC13V, 5V, GND supplied from SMPS PCB 2. Circuit for controlling Step-Valve (3-Way Valve) * Option 3. FAN MOTOR control part : To supply the power from 8.3V ~ 12V according to the motor types. (F,R,C,ICE) 4. EEPROM : Save and record every kinds of data. 5. Transmit inputted signals from every sensor into MICOM after eliminate the noise. 6.
AW-SEMTransform(RF267,2#3957D82009.8.204:56PM페이지105 in PCB DIAGRAM 6-2) PCB Layout with part position (Inverter Board) 1. Inrush current protecting area : It prevents an instant inrush of current generated in condenser when plug in. 2. PCB Power Bus : power bus (Hybrid IC). It supplies DC15V and 5V to MICOM. 3. Location detecting resistance area : It detects motor location through the current detected. 4. Current detecting area : It detects the current from the SHUNT resistance and controls PWM DUTY. 5.
AW-SEMTransform(RF267,2#3957D82009.8.204:56PM페이지106 in PCB DIAGRAM 6-3) Connector Layout with part position (Main Board) 6-3-1.
AW-SEMTransform(RF267,2#3957D82009.8.204:56PM페이지107 in PCB DIAGRAM 6-4) PCB Layout with part position (Main Board) 6-3-2.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.204:56PM페이지109 in 7.
AW-SEMTransform(RF267,2#3957D82009.8.
AW-SEMTransform(RF267,2#3957D82009.8.204:56PM페이지111 in 8. SCHEMATIC DIAGRAM 8-1) Whole block diagram 8-1-1.
AW-SEMTransform(RF267,2#3957D82009.8.204:56PM페이지112 in SCHEMATIC DIAGRAM 8-1) Whole block diagram 8-1-2.
AW-SEMTransform(RF267,2#3957D82009.8.204:56PM페이지113 in SCHEMATIC DIAGRAM 8-1) Whole block diagram 8-1-3.
AW-SEMTransform(RF267,2#3957D82009.8.204:56PM페이지114 in SCHEMATIC DIAGRAM 8-2) CIRCUIT DIAGRAM 8-2-1.
AW-SEMTransform(RF267,2#3957D82009.8.204:56PM페이지115 in SCHEMATIC DIAGRAM 8-2) CIRCUIT DIAGRAM 8-2-2.
F 116 MAIN OPTION 8: Twin Ice Maker 7: Best X: Defeature (TRANSFORM) 6: Better 3: Good (TRANSFORM) Capacity : CU.
AW-SEMTransform(RF267,2#3957D82009.8.204:56PM페이지117 in Mexico Av. Benito Juarez No.119, Parque Ind. Queretaro Km 28.5 Carr. Qro. S.L.P Mz.11 LT.12, C.P.76220 Santa Rosa de Jauregui, Santiago de Queretaro, Queretaro Mexico TEL : 52-442-296-9000(9408) FAX : 52-442-240-9072 - This Service Manual is a property of Samsung Electronics Co., Ltd. Any unauthorized use of Manual can be punished under applicable International or domestic law. © Samsung Electronics Co., Ltd.
