Refrigerator User manual RH56J69* SEUK Free Standing Appliance DA68-03176A (EN)-00.indd 1 2015. 1. 14.
Contents Safety information 3 Contents Important safety symbols Severe warning signs for transportation and site Severe warning signs for installation Caution signs for installation Severe warning signs for using Caution signs for using Caution signs for cleaning and maintenance Severe warning signs for disposal Additional tips for proper usage 4 5 6 8 9 12 13 14 15 Setting up 18 Getting ready to install the refrigerator Required tools Removing the refrigerator doors Reattaching the refrigerator door
Safety information • • • • Before operating the appliance, please read this manual thoroughly and retain it at a safe place near the appliance for your future reference. Use this appliance only for its intended purpose as described in this instruction manual.
Safety information Safety information Important safety symbols WARNING Hazards or unsafe practices that may result in severe personal injury or death. CAUTION Hazards or unsafe practices that may result in minor personal injury or property damage. NOTE Do NOT attempt. Do NOT disassemble. Do NOT touch. Follow directions carefully. Unplug the power plug from the wall socket. Make sure the machine is grounded to prevent electric shock. Call the contact center for help.
WARNING - • • • When transporting and installing the appliance, care should be taken to ensure that no parts of the refrigerating circuit are damaged. Refrigerant leaking from the pipe work could ignite or cause an eye injury. If a leak is detected, avoid any naked flames or potential sources of ignition and air the room in which the appliance is standing for several minutes.
Safety information Safety information Severe warning signs for installation WARNING • • - • • • • - • Do not install the refrigerator in a damp place or place where it may come in contact with water. Deteriorated insulation of electrical parts may cause an electric shock or fire. Do not place this refrigerator in direct sunlight or expose to the heat from stoves, room heaters or other appliance. Do not plug several appliances into the same multiple power board.
• • • • - • - Safety information • - • This refrigerator must be properly installed and located in accordance with the manual before it is used. Connect the power plug in proper position with the cord hanging down. If you connect the power plug upside down, wire can get cut off and cause fire or electric shock. Make sure that the power plug is not squashed or damaged by the back of the refrigerator. When moving the refrigerator, be careful not to roll over or damage the power cord.
Safety information Safety information Caution signs for installation CAUTION • Keep ventilation opening in the appliance enclosure or mounting structure clear of obstruction. • Allow the appliance to stand for 2 hours after installation. - When installing the refrigerator, make sure both legs contact the floor for secure installation. Legs are located at the bottom back of each door. Insert a flathead screwdriver and turn it in the direction of the arrow until it is level.
WARNING • • • • • • - • Do not insert the power plug with wet hands. Do not store articles on the top of the appliance. When you open or close the door, the articles may fall and cause personal injury and/or material damage. Do not put items filled with water on the refrigerator. If spilled, there is a risk of fire or electric shock. Do not let children hang on the door. Failure to do so may cause serious personal injury.
Safety information Safety information • • • • • • • • • - • Do not store low temperature-sensitive pharmaceuticals products, scientific materials or other low temperature-sensitive products in the refrigerator. Products that require strict temperature controls must not be stored in the refrigerator. Do not place or use electrical appliance inside the refrigerator, unless they are of a type recommended by the manufacturer. Do not use a hair dryer to dry the inside of the refrigerator.
• • • - Safety information - • If the appliance generates a strange noise, a burning or smell or smoke, unplug the power plug immediately and contact your nearest service center. Failing to do so may result in electric or fire hazards. Keep ventilation opening in the appliance enclosure or mounting structure clear of obstruction. If you experience difficulty when changing the light, contact service agents. If the products equipped with LED Lamp, do not disassemble Lamp Cover and LED Lamp by yourself.
Safety information Safety information Caution signs for using CAUTION - • • - • - • • • • • To get best performance of product, Do not place foods too closely in front of the vents at the rear of the appliance as it can obstruct free air circulation in the refrigerator compartment. Wrap the food up properly or place it in airtight containers before put it into the refrigerator. Do not place carbonated or fizzy drinks in the freezer compartment. Do not put bottles or glass containers in the freezer.
In order to operate the ice maker properly, water pressure of 138 ~ 862 kPa (19.9 ~ 125.1 psi) is required. Safety information • Caution signs for cleaning and maintenance CAUTION • • • • - • Do not directly spray water inside or outside the refrigerator. There is a risk of fire or electric shock. Do not spray inflammable gas near the refrigerator. There is a risk of explosion or fire. Do not spray cleaning products directly on the display. Printed letters on the display may come off.
Safety information Safety information Severe warning signs for disposal WARNING • • • • • Ensure that none of the pipes on the back of the appliance are damaged prior to disposal. R-600a or R-134a is used as a refrigerant. Check the compressor label on the rear of the appliance or the rating label inside the refrigerator to see which refrigerant is used for your refrigerator.
NOTE • - • • • • • • • In the event of a power failure, call the local office of your Electricity Company and ask how long it is going to last. Most power failures that are corrected within an hour or two will not affect your refrigerator temperatures. However, you should minimize the number of door openings while the power is off. Should the power failure last more than 2 hours, remove all ice in the Ice Bucket. Should the power failure last more than 24 hours, remove all frozen food.
Safety information Safety information Saving energy tips - Install the appliance in a cool, dry room with adequate ventilation. Ensure that it is not exposed to direct sunlight and never put it near a direct source of heat (radiator, for example). - Never block any vents or grilles on the appliance. - Allow warm food to cool down before placing it in the appliance. - Put frozen food in the refrigerator to thaw. You can then use the low temperatures of the frozen products to cool food in the refrigerator.
Safety information This appliance is intended to be used in household and similar applications such as - staff kitchen areas in shops, offices and other working environments; - farm houses and by clients in hotels, motels and other residential type environments; - bed and breakfast type environments; - catering and similar non-retail applications. English 17 DA68-03176A (EN)-00.indd 17 2015. 1. 14.
Setting up Getting ready to install the refrigerator Congratulations on the purchase of your Samsung Side-By-Side Refrigerator. We hope you will enjoy the many state-of-the-art features and efficiencies that this new appliance has to offer. Selecting the best location for the refrigerator Setting up • • • • • • Select a location with easy access to the water supply. Select a location without direct exposure to sunlight. Select a location with level (or nearly level) flooring.
NOTE Spacer Spacer Spacer(gray block) installation For better performance, please certainly fix the spacer on the rear of unit when installing the refrigerator. It is improving refrigerator performance. Assembly method Setting up Take out packed spacer from the lowest guard of the fridge. Check assembly location at the rear of Refrigerator like picture. Locate spacer assembly location and put spacer on the rear plate of Refrigerator.
Setting up Required tools Required Tools (Not provided) Flat-blade screw driver (-) Pliers Allen wrench 5 mm Setting up Philips screwdriver (+) Socket wrench 10 mm Removing the refrigerator doors If your entrance won’t allow the refrigerator to pass easily through it, you can remove the doors. Removing the front leg cover First, open both the freezer and refrigerator doors, and then take off the front leg cover by removing the three screws counter-clockwise. 20 English DA68-03176A (EN)-00.
Separating the water supply line from the refrigerator If your entrance won’t allow the refrigerator to pass easily through it, you can remove the doors. 1. Remove the water line by pressing the coupler (1) and pulling the water line (2) away. CAUTION 1 Be careful that the water tube match same colour. Setting up 2 English 21 DA68-03176A (EN)-00.indd 21 2015. 1. 14.
Setting up Removing the freezer door A few things to mention first. • Make sure that you lift the door straight up so the hinges are not bent or broken. • Be careful not to pinch the water tubing and wire harness on the door. • Place doors on a protected surface to prevent scratching or damage. 1 1. With the Freezer door closed, remove the upper hinge cover (1) using a screwdriver, and then disconnect the wires by gently pulling them apart (2). 2 Setting up 3 2.
Removing the fridge door 1. With the door closed, remove the upper hinge cover (1) using a screwdriver. 1 2 Setting up 2. Remove hinge screws (2) by turning counter-clockwise, and take off the upper hinge (3). Be careful that the door does not fall on you as you are removing it 3 5 3. Remove the door from the lower hinge (4) by lifting the door straight up (5). 4 English 23 DA68-03176A (EN)-00.indd 23 2015. 1. 14.
Setting up Disassemble the cold compartment show case door 1. Disassemble the housing connector. Setting up 2. Disassemble the three fastening screws on the top hinge of the show case. 3. Remove the show case door. 24 English DA68-03176A (EN)-00.indd 24 2015. 1. 14.
Reattaching the refrigerator doors Once you have safely placed your refrigerator where you plan for it to stay, it is time to put the doors back on. Reattaching the Freezer Door 1 2 7 5 6 3 Setting up 1. Replace the freezer door by inserting the water line (1) back into the lower corner of the door and then into the hole on the lower hinge (2). Gently pull the water line back down so that it runs straight, with no kinks or bends. 2.
Setting up 8 3. Place the front part of the upper hinge cover (8) on the front of the upper hinge (9) and reattach with the screw. 9 Reattaching the fridge door Setting up 1. Fit the hole in the corner of the fridge door (1) over the lower hinge (2). 1 2 2. Insert the upper hinge shaft (3) into the hole on the hinge (4). Make sure the hinge is level between the upper hinge hole (5) and the hole on the top of the cabinet (6). Then, reattach hinge screws (7) by turning it in a clock wise direction.
8 3. Place the front part of the upper hinge cover (8) on the front of the upper hinge (9) and reattach it with the screw. 9 Reattaching the water supply line 1. Insert the water line (2) into the coupler (1). Setting up 1 2 Center of transparent coupler clip A (6.35 mm) 2. The Water Line must be fully Inserted to the center of transparent coupler to prevent water leakage from the dispenser. 3. Insert the 2 clips in the install pack and check that each clip holds the line firmly.
Setting up Reattaching the front leg cover NOTE Before attaching the cover, check water connector for leakage. Replace the front leg cover by turning the three screws clockwise, as shown in the figure. Levelling the refrigerator Now that the doors are back on the refrigerator, you will want to make sure the refrigerator is level so you can then make final adjustments. If the refrigerator is not level, it will not be possible to get the doors perfectly even.
How to adjust the door height If one door is lower than the other: • B A B 1. Open the door that needs to be adjusted and loosen the clamping nut (A) at the bottom of the door by turning it clockwise ( ) using the spanner included in the product package. (Raise the lower of the two doors first.) Setting up A • The refrigerator door height can be adjusted using the adjustment nuts located at the bottom of each door.
Setting up A 3. Once the doors are level, turn the clamping nut (A) counterclockwise ( ) to tighten it. NOTE Adjusting the level when the refrigerator is empty can result in the refrigerator becoming uneven again once items have been placed inside. If this occurs, adjust the level again.
Checking the water dispenser line (optional) A water dispenser is just one of the helpful features on your new Samsung refrigerator. To help promote better health, the Samsung water filter removes unwanted particles from your water. However, it does not sterilize or destroy microorganisms. You will need to purchase a water purifying system to do that. In order for the icemaker to operate properly, water pressure of 138 ~862 kPa is required.
Setting up To refit the ice bucket • 90° • • Assemble it in the reverse order of disassembly. Push the bucket in firmly until you hear a clicking sound. When the bucket does not fit into its place, turn the gear handle on its back by 90 degrees and reinstall it again as shown in figure 2. Figure2 Setting up Normal operation • • • Ice Chute • Any sounds you hear when the ice maker dumps ice into the bucket are part of normal operation.
CAUTION • • • • • • • Setting up • When ICE OFF blinks on the display panel, reinsert the bucket and/or make sure it’s installed properly. When the door is open, the Ice and water dispenser do not work. If you close the door hard, it may cause water spilling over the ice maker. To prevent dropping the ice bucket, use both hands when removing it. To prevent injury, be sure to clean up any ice or water that may have dropped on the floor. Do not let children hang on the ice dispenser or on the bucket.
Setting up Installing the water dispenser line (for exterior model) Parts for water line installation Pipe connector Purifier lock-clip Purifier Water line Setting up Water line fixer and screws Connecting to the water supply line Connect the water pipe with coupler and tap. 1. Close the main water tap. 2. Connect coupler (A) to the tap. CAUTION The water line must be connected to the cold water pipe. If it is connected to the hot water pipe, it may cause the purifier to malfunction.
select the location where the purifier is to install. (Model with the purifier) COUPLER (A) • If you wish to reassemble the water inlet and outlet sides of the purifier during purifier installation, see the reference illustration. • Cut the water line attached to the purifier to the appropriate place after measuring the distance between the purifier and the cold water tap.
Setting up Attach the purifier lock-clip. • Hold the purifier lock-clip in the appropriate position (under the sink for example) and fix it tightly into place where to screw. Purifier lock-clip CAUTION Do not fix the purifier on the refrigerator or rear of refrigerator, it may cause material damage. Setting up Secure the purifier in position. • Fix the purifier in position, as shown in the figure on the right. • Remove the compressor cover of the refrigerator.
Secure the water line. • Clip A Water line • Using clip (A), fix the water line to the wall (the back of refrigerator). When the water line is secure, make sure whether the water line is not excessively bent, pinched or squashed. Removing any residual matter inside the water supply line after installing filter. Setting up 1. Turn ON the main water supply & turn OFF the valve to the water supply line. 2. Run water through the dispenser until the water runs clear (approximate 3 liter).
Operating Initial settings 08 05 01 06 02 07 03 04 Operating 01 Power freeze button Speeds up the time needed to freeze products in the freezer. This can be helpful if you need to quickly freeze items that spoil easily or if the temperature in the freezer has warmed dramatically (For example, if the door was left open). 02 Freezer button Press the Freezer button to set the freezer to your desired temperature, You can set the temperature between -15 °C and -23 ºC.
06 Child lock function By pressing the Vacation button and the Fridge button simultaneously for 3 seconds, all buttons will be locked. The Water dispenser lever and the Ice lever will not work either. To cancel this function, Press these two buttons for 3 seconds again. 07 Fridge button Press the Fridge button to set the fridge to your desired temperature. You can set temperature between 1 °C and 7 °C. 08 Door open function If the fridge or the freezer door is open, the Door Open icon is lit.
Operating Display Off Function To energy conservation the Panel Display turns off automatically under the following conditions: When no button has been pressed, when no doors are open, or when no Dispenser Lever has been pushed. However, the icon indicating your Vacation or Cubed / Crushed / Ice Off, will stay on. When you press a button, open a door, or push Dispenser Lever, the Panel Display will turn on again.
Using the ice and cold water dispenser Press the Ice Type button to select the type of ice you want NOTE Ice is made in cubes. When you select Crushed, the icemaker grinds the ice cubes into crushed ice. No Ice Select this if you want to turn off the icemaker Dispensing ice Place your glass underneath the ice outlet and push gently against the ice dispenser lever with your glass. Make sure the glass is in line with the dispenser to prevent the ice from bouncing out.
Operating Parts and features 01 03 05 06 02 07 04 Operating Designed to store lots of easily. 01 Ice maker bucket WARNING Do not put your fingers, hands or any other objects in the ice chute or the ice maker bucket. This may result in personal injury or material damage. 02 Multipurpose Freezer Compartments Features tall freezer compartments for more efficient food storage. Do not use these compartments for ice cream or items you intend to store for a long time.
04 Drawers Best used to store meats or dry foods. Stored food should be wrapped securely using foil or other suitable wrapping materials or containers. 05 Refrigerator shelves Use for storing general types of food that require refrigeration. 06 Door bins Designed to handle large, bulky items such as gallons of milk or other large bottles and containers. 07 Fruit & vegetable drawer Used to preserve the freshness of your stored vegetables and fruits.
Operating NOTE GUARD FRE-UPP (Optional) For more space, you can store food with Guard FRE-UPP instead of the ice bucket, and remove the COVER-ICE MAKER. If you remove the ice bucket, ICE OFF will blink on the display panel. Furthermore, you can remove the freezer Upper drawer since it does not affect thermal and mechanical characteristics. A declared storage volume of frozen food storage compartment is calculated with “Guard FRE-UPP” positioned and “COVERICE MAKER”, “Upper Drawer” removed.
2. Remove the door bin by holding the door bin with both hands and then gently lift it up. 3. Remove the Plastic drawer by pulling it out and slightly lifting it up. Operating 4. Ice bucket (freezer) Remove the Icemaker Bucket by lifting up and pulling it out slowly. • Grip the handle as shown in the figure • Lift the low part slightly • Take the ice bucket out slowly. NOTE Do not use excessive force when removing the cover. Otherwise, the cover may break and cause injury.
Operating Removing the fridge accessories 1. Remove the spill Proof Glass Shelf by pulling the shelf out as far as it will go. Then, gently lift it up and gently remove it. 2. Remove the Vegetable & Fruit Drawer by pressing on the indentations found on the inside left and right sides of the Veggie Box/Dry Box cover and remove by pulling forward. Holding the drawer with one hand, lift it up a little bit while pulling it forward and take it out of the refrigerator. Operating 3.
Cleaning the refrigerator WARNING Do not use Benzene, Thinner or Clorox™ for cleaning. They may damage the surface of the appliance and can create a risk of fire. CAUTION Do not spray the refrigerator with water while it is plugged in, as it may cause an electric shock. Do not clean the refrigerator with benzene, thinner or car detergent for risk of fire. Replacing the interior light NOTE For LED lamp, please contact service engineer to replace it.
Operating NOTE For Exterior model 1. Shut off water supply. 2. Note the Flow direction on the filter. 3. Insert water supply tube into the inlet side of the filter until the tube stop. Flow direction Water supply Inlet side Permeat NOTE You must also ensure that the cut is square and not at any sort of angle as this could cause a leak 4. After inserting tube, put together the clip strongly. The Clip fix the tube. Operating 5. Turn on the water and check for leaks. If leaks occur, repeat step 1,2,3,4.
7. Lastly, Dispense 1 L of water through water dispenser and throw away. Make sure that water flows clearly again before drinking. NOTE A newly installed water filter cartridge may cause water to briefly spurt from the water dispenser. This is due to air getting into the line. It should pose no problem to operation. Ordering replacement filters To order more water filter cartridges, contact your authorized Samsung dealer. - External Filter - HAFEX/EXP Operating English 49 DA68-03176A (EN)-00.
Troubleshooting Problem Action • • • The refrigerator does not work at all or it does not chill sufficiently. • • • The food in the fridge is frozen. • • • • You hear unusual noises or sounds. Troubleshooting The front corners of the appliance are hot and condensation is occurring. • • • • Check that the power plug is properly connected. Is the temperature control on the display panel set to the correct temperature? Try setting it to a lower temperature.
Problem Action • Ice is not dispensing. • • • • You can hear water bubbling in the refrigerator. There is a bad smell in the refrigerator. • This is normal. The bubbling comes from the refrigerant coolant liquid circulating through the refrigerator. • • Has a food item spoiled? Make sure that strong smelling food (for example, fish) is wrapped so that it is airtight. Clean out your freezer periodically and throw away any spoiled food.
Troubleshooting Problem Action • • Water dispenser is not functioning. • • Is the water line connected and the shut-off valve open? Has the water supply line tubing been crushed or kinked? Make sure the tubing is free and clear of any obstruction. Is the water tank frozen because the refrigerator temperature is too low? Try selecting a warmer setting on the main display panel. Check if the filter is properly installed. If it is not properly installed, the water dispenser may not work.
Circuit diagram DA68-03176A (EN)-00.indd 53 2015. 1. 14.
Memo DA68-03176A (EN)-00.indd 54 2015. 1. 14.
Ambient Room Temperature Limits This refrigerator is designed to operate in ambient temperatures specified by its temperature class marked on the rating plate.
Contact SAMSUNG WORLD WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. COUNTRY CALL OR VISIT US ONLINE AT AUSTRIA 0800 - SAMSUNG (0800 7267864) www.samsung.com/at/support COLOMBIA Bogotá 600 12 72 Gratis desde cualquier parte del país 01 8000 112 112 ó desde su celular #SAM(726) www.samsung.com/co/support EIRE 0818 717100 www.samsung.com/ie/support MALAYSIA 1800-88-9999 www.samsung.