User Manual S24D330H S24D332H The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. The contents of this manual are subject to change without notice to improve quality. © Samsung Electronics Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited.
Table of contents Before Using the Product Securing the Installation Space Precautions for storage 4 4 Safety Precautions Cleaning Electricity and Safety Installation Operation 4 5 5 6 7 Preparations Parts Frontal Buttons Reverse Side Changing Brightness and Contrast settings Adjusting the Product Tilt Anti-theft Lock 9 9 10 11 11 12 Installation Attaching the Stand Removing the Stand 13 13 14 Connecting and Using a Source Device Screen Setup Pre-connection Checkpoints Brightness 18 Contrast 1
Table of contents Configuring Tint Setup and Reset Specifications Red 22 Reset All 25 General 31 Green 22 Eco Saving Plus 25 Standard Signal Mode Table 32 Blue 22 Off Timer 25 Color Tone 23 PC/AV Mode 26 Gamma 23 Key Repeat Time 26 Source Detection 26 INFORMATION 26 Resizing or Relocating the Screen Language 24 Menu H-Position & Menu V-Position 24 Installing the Software Display Time 24 Easy Setting Box Transparency 24 Appendix Responsibility for the Pay Service (Cos
Chapter 01 Before Using the Product Securing the Installation Space Safety Precautions Ensure some space around the product for ventilation. An internal temperature rise may cause fire and damage the product. Be sure to allow the amount of space as shown below or greater when installing the product. ――The exterior may differ depending on the product. Warning A serious or fatal injury may result if instructions are not followed.
Cleaning Electricity and Safety ――Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched. ――Take the following steps when cleaning. Warning 1 Power off the product and computer. •• Do not use a damaged power cord or plug, or a loose power socket. 2 Disconnect the power cord from the product. •• Do not use multiple products with a single power socket. ――Hold the power cable by the plug and do not touch the cable with wet hands.
Installation Warning Caution •• DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF THE PRODUCT. DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES. •• Do not drop the product while moving. •• Do not install the product in poorly ventilated spaces such as a bookcase or closet. •• Install the product at least 10 cm away from the wall to allow ventilation. •• Keep the plastic packaging out of the reach of children. ‒‒ Children may suffocate.
Operation Warning •• There is a high voltage inside the product. Never disassemble, repair or modify the product yourself. ‒‒ Contact Samsung Customer Service Center for repairs. •• To move the product, first disconnect all the cables from it, including the power cable. •• If the product generates abnormal sounds, a burning smell or smoke, disconnect the power cord immediately and contact Samsung Customer Service Center.
Caution •• Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage burn-in or defective pixels. •• Do not touch the screen when the product has been turned on for an extended period of time as it will become hot. ‒‒ Activate power-saving mode or a moving-picture screen saver if you will not be using the product for an extended period of time. •• Store small accessories out of the reach of children.
Chapter 02 Preparations Parts Icons Description Open or close the onscreen display (OSD) menu, or return to the parent menu. OSD control lock: Maintain the current settings, or lock the OSD control to prevent unintended changes to settings. Frontal Buttons •• Enable: To lock the OSD control, press the ――The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. SOURCE AUTO button for Mode is available.
Icons Reverse Side Description Press the button to automatically adjust the screen settings. ――Changing the resolution in Display Properties will activate the Auto Adjustment function. ――This function is only available in Analog mode. ――The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. Turn the screen on or off.
Changing Brightness and Contrast settings Adjust the Brightness and Contrast setting using the menu is displayed). buttons in the initial screen (where no OSD Adjusting the Product Tilt ――The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. -1° (± 2°) ~ Brightness 20° ( ±2°) 100 Contrast 75 ――The displayed image may differ depending on the model. ――The default brightness can vary depending on the region.
Anti-theft Lock ――An anti-theft lock allows you to use the product securely even in public places. ――The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details. To lock an anti-theft locking device: DC 14V RGB IN 1 Fix the cable of your anti-theft locking device to a heavy object such as a desk. 2 Put one end of the cable through the loop on the other end.
Installation Attaching the Stand ――Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards. ――The exterior may differ depending on the product. Insert the stand neck into the stand base in the direction shown in the figure. Place a soft cloth over the table to protect the product and place the product onto the cloth so that the front of the product is facing downwards. Check that the stand neck is firmly connected.
Removing the Stand ――Before removing the stand from the monitor, place the monitor on a flat and stable surface with the screen facing down. ――The exterior may differ depending on the product. Place a soft cloth over the table to protect the product and place the product onto the cloth so that the front of the product faces downwards. Remove the stand neck from the stand base by pulling it in the direction of the arrow as shown in the figure.
Chapter 03 Connecting and Using a Source Device Pre-connection Checkpoints ――Before connecting a source device, read the user manual provided with it. The number and locations of ports on source devices may differ from device to device. ――Do not connect the power cable before connecting all other cables. Connecting and Using a PC Select a connection method suitable for your PC. ――Connecting parts may differ in different products. ――Provided ports may vary depending on the product.
Connection Using the HDMI Cable HDMI IN Connecting the Power Power connection using integrated AC/DC adapter Connection Using an HDMI-DVI Cable DC 14V HDMI IN ――The input voltage is switched automatically. Power connection using detachable AC/DC adapter DC 14V ――The input voltage is switched automatically.
Correct posture to use the product Driver Installation ――You can set the optimum resolution and frequency for this product by installing the corresponding drivers. ――To install the latest version of the product driver, download it from the Samsung Electronics website at http://www.samsung.com. Setting Optimum Resolution An information message about setting optimum resolution will appear if you power on the product for the first time after purchase.
Chapter 04 Screen Setup Configure the screen settings such as brightness. A detailed description of each function is provided. Refer to your product for details. ――The functions available may vary depending on the product model. Refer to the actual product. Contrast Brightness Adjust the contrast between the objects and background. (Range: 0~100) A higher value will increase the contrast to make the object appear clearer. You can adjust the general brightness of the picture.
Game Mode SAMSUNG MAGIC Bright Configure the product screen settings for game mode. This menu provides an optimum picture quality suitable for the environment where the product will be used. Use this feature when playing games on a PC or when a game console such as PlayStation™ or Xbox™ is connected. ――This menu is not available when Eco Saving Plus is enabled.
SAMSUNG MAGIC Angle SAMSUNG MAGIC Upscale MAGICAngle allows you to configure the settings to obtain the optimum picture quality according to your viewing angle. MAGICUpscale function ――This menu is not available when SAMSUNG Bright is set to Cinema or Dynamic Contrast mode. ――This menu is not available when SAMSUNG Bright is set to Cinema or Dynamic Contrast mode. SAMSUNG MAGIC SAMSUNG can enhance the layers of the picture details and the vividness of the picture.
HDMI Black Level Coarse If a DVD player or set-top box is connected to the product via HDMI, image quality degradation (contrast/ color degradation, black level, etc.) may occur, depending on the connected source device. In such case, HDMI Black Level can be used to adjust the image quality. ――This menu is available in Analog mode only. Adjust the screen frequency. If this is the case, correct the degraded picture quality using HDMI Black Level. ――This function is only available in HDMI mode.
Chapter 05 Configuring Tint A detailed description of each function is provided. Refer to your product for details. SAMSUNG Bright is in Cinema or Dynamic Contrast mode. This menu is not available when Game Mode is enabled. Adjust the tint of the screen. This menu is not available when MAGIC ――The functions available may vary depending on the product model. Refer to the actual product. Green Red Adjust the value of the color green in the picture.
Color Tone Adjust the general color tone of the picture. ――This menu is not available when SAMSUNGAngle is enabled. MAGIC ――This menu is not available when SAMSUNG Bright is in Cinema or Dynamic Contrast mode. MAGIC ――This menu is not available when Game Mode is enabled. •• Cool 2: Set the color temperature to be cooler than Cool 1. •• Cool 1: Set the color temperature to be cooler than Normal mode. •• Normal: Display the standard color tone.
Chapter 06 Resizing or Relocating the Screen A detailed description of each function is provided. Refer to your product for details. ――The functions available may vary depending on the product model. Refer to the actual product. Menu H-Position & Menu V-Position Language Menu H-Position: Move the menu position to the left or right. Menu V-Position: Move the menu position up or down. Set the menu language. ――A change to the language setting will only be applied to the onscreen menu display.
Chapter 07 Setup and Reset A detailed description of each function is provided. Refer to your product for details. ――The functions available may vary depending on the product model. Refer to the actual product. Reset All Eco Saving Plus Reduce energy consumption compared to consumption at the maximum brightness level. ――This option is not available when SAMSUNG Bright is in Dynamic Contrast mode. MAGIC Return all the settings for the product to the default factory settings.
PC/AV Mode INFORMATION Set PC/AV Mode to AV. The picture size will be enlarged. View the current input source, frequency and resolution. This option is useful when you view a movie. •• Set to PC when connected to a PC. •• Set to AV when connected to an AV device. ――This function does not support Analog mode. ――Supplied for the wide models only such as 16:9 or 16:10.
Chapter 08 Installing the Software Easy Setting Box System Requirements OS Hardware •• Windows XP 32Bit/64Bit •• At least 32MB of memory •• Windows Vista 32Bit/64Bit •• At least 60MB of free space on the hard disk drive •• Windows 7 32Bit/64Bit Easy Setting Box enables users to use the monitor by partitioning multiple sections. •• Windows 8 32Bit/64Bit To install the latest version of Easy Setting Box, download it from the Samsung Electronics website at http://www.samsung.com. •• Windows 8.
Chapter 09 Troubleshooting Guide Requirements Before Contacting Samsung Customer Service Center ――Before calling Samsung Customer Service Center, test your product as follows. If the problem persists, contact Samsung Customer Service Center. Check the following. Installation issue (PC mode) The screen keeps switching on and off. Check the cable connection between the product and PC, and ensure the connectors are locked.
Not Optimum Mode is displayed. Video playback is choppy. This message appears when the signal from the graphics card exceeds the maximum resolution or frequency for the product. Playback of high-definition large video files can be choppy. This may be because the video player is not optimized for the computer resource. Change the maximum resolution and frequency to suit the product performance, referring to Standard Signal Mode Table (P.32). Try playing the file on another video player.
Q&A ――Refer to the user manual for your PC or graphics card for further instructions on adjustment. How can I change the frequency? Set the frequency on your graphics card. •• Windows XP: Go to Control Panel Appearance and Themes •• Windows ME/2000: Go to Control Panel System Control Panel Display Settings Advanced Appearance and Personalization •• Windows 8(Windows 8.1): Go to Settings settings.
Chapter 10 Specifications General Model Name S24D330H Size 24 Class (24 Inches / 61 cm) Display area 531.36 mm (H) x 298.89 mm (V) S24D332H 0.27675 mm (H) x 0.27675 mm (V) 0.01090 Inches (H) x 0.01090 Inches (V) Maximum Pixel Clock 148.5 MHz 148.5 MHz (D-SUB) 174.5 MHz (HDMI) Power Supply This monitor can be installed and used with any Plug-and-Play compatible systems. Two-way data exchange between the monitor and PC system optimizes the monitor settings.
Standard Signal Mode Table Model Name S24D330H Synchronization Resolution Horizontal Frequency 30 – 81 kHz Vertical Frequency 56 – 75 Hz Optimum Resolution 1920 x 1080 @ 60 Hz Maximum Resolution 1920 x 1080 @ 60 Hz If a signal that belongs to the following standard signal modes is transmitted from your PC, the screen will automatically be adjusted. If the signal transmitted from the PC does not belong to the standard signal modes, the screen may be blank even though the power LED turns on.
Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 1152 x 864 67.500 75.000 108.000 +/+ VESA, 1280 x 720 45.000 60.000 74.250 +/+ VESA, 1280 x 800 49.702 59.810 83.500 -/+ VESA, 1280 x 1024 63.981 60.020 108.000 +/+ VESA, 1280 x 1024 79.976 75.025 135.000 +/+ VESA, 1440 x 900 55.935 59.887 106.500 -/+ VESA, 1600 x 900 RB 60.000 60.000 108.000 +/+ VESA, 1680 x 1050 65.290 59.954 146.
Model Name S24D332H Synchronization Resolution Horizontal Frequency 30 – 81 kHz Vertical Frequency 56 – 75 Hz Optimum Resolution 1920 x 1080 @ 60 Hz (D-SUB) 1920 x 1080 @ 75 Hz (HDMI) Maximum Resolution 1920 x 1080 @ 60 Hz (D-SUB) 1920 x 1080 @ 75 Hz (HDMI) If a signal that belongs to the following standard signal modes is transmitted from your PC, the screen will automatically be adjusted.
Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 1024 x 768 60.023 75.029 78.750 +/+ VESA, 1152 x 864 67.500 75.000 108.000 +/+ VESA, 1280 x 720 45.000 60.000 74.250 +/+ VESA, 1280 x 800 49.702 59.810 83.500 -/+ VESA, 1280 x 1024 63.981 60.020 108.000 +/+ VESA, 1280 x 1024 79.976 75.025 135.000 +/+ VESA, 1440 x 900 55.935 59.887 106.500 -/+ VESA, 1600 x 900 RB 60.000 60.000 108.
Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 1024 x 768 48.363 60.004 65.000 -/- VESA, 1024 x 768 56.476 70.069 75.000 -/- VESA, 1024 x 768 60.023 75.029 78.750 +/+ VESA, 1152 x 864 67.500 75.000 108.000 +/+ VESA, 1280 x 720 45.000 60.000 74.250 +/+ VESA, 1280 x 800 49.702 59.810 83.500 -/+ VESA, 1280 x 1024 63.981 60.020 108.000 +/+ VESA, 1280 x 1024 79.976 75.025 135.000 +/+ VESA, 1440 x 900 55.
Chapter 11 Appendix Responsibility for the Pay Service (Cost to Customers) A Product damage caused by customer's fault ――When the service is requested, in spite of in warranty, we may charge you for a visit from a service •• External impact or drop. technician in the following cases. Not a product defect Cleaning of the product, Adjustment, Explanation, Re-installation and etc. •• If a service technician gives instructions on how to use product or simply adjusts options without disassembling product.
