User Manual S27E330H S27E332H The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. The contents of this manual are subject to change without notice to improve quality. © Samsung Electronics Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited.
Table of contents Before Using the Product Securing the Installation Space Precautions for storage 4 4 Safety Precautions Cleaning Electricity and Safety Installation Operation 4 5 5 6 7 Preparations Connecting and Using a Source Device Screen Setup Pre-connection Checkpoints Brightness 22 Contrast 22 Sharpness 22 Eye Saver Mode 23 Game Mode 23 SAMSUNG MAGIC Bright 23 SAMSUNG MAGIC Angle 24 SAMSUNG MAGIC Upscale 24 18 Connecting and Using a PC 18 Connection Using the D-SUB Cable (An
Table of contents Configuring Tint Setup and Reset Troubleshooting Guide Red 26 Reset All 29 Green 26 Eco Saving Plus 29 Blue 26 Off Timer 30 Color Tone 27 PC/AV Mode 30 Gamma 27 Key Repeat Time 30 Source Detection 30 Power LED On 30 Specifications INFORMATION 31 General 36 Standard Signal Mode Table 37 Resizing or Relocating the Screen Language 28 Menu H-Position & Menu V-Position 28 Display Time 28 Installing the Software Transparency 28 Easy Setting Box 32 Req
Chapter 01 Before Using the Product Securing the Installation Space Safety Precautions Ensure some space around the product for ventilation. An internal temperature rise may cause fire and damage the product. Be sure to allow the amount of space as shown below or greater when installing the product. ――The exterior may differ depending on the product. Warning A serious or fatal injury may result if instructions are not followed.
Cleaning ――Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched. ――Take the following steps when cleaning. Electricity and Safety Warning 1 Power off the product and computer. •• Do not use a damaged power cord or plug, or a loose power socket. 2 Disconnect the power cord from the product. •• Do not use multiple products with a single power socket. ――Hold the power cable by the plug and do not touch the cable with wet hands.
Installation Warning Caution •• DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF THE PRODUCT. DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES. •• Do not drop the product while moving. •• Do not install the product in poorly ventilated spaces such as a bookcase or closet. •• Install the product at least 10 cm away from the wall to allow ventilation. •• Keep the plastic packaging out of the reach of children. ‒‒ Children may suffocate.
Operation Warning •• There is a high voltage inside the product. Never disassemble, repair or modify the product yourself. ‒‒ Contact Samsung Customer Service Center for repairs. •• To move the product, first disconnect all the cables from it, including the power cable. •• If the product generates abnormal sounds, a burning smell or smoke, disconnect the power cord immediately and contact Samsung Customer Service Center.
Caution •• Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage burn-in or defective pixels. ‒‒ Activate power-saving mode or a moving-picture screen saver if you will not be using the product for an extended period of time. •• Disconnect the power cord from the power socket if you do not plan on using the product for an extended period of time (vacation, etc). ‒‒ Dust accumulation combined with heat can cause a fire, electric shock or electric leakage.
Chapter 02 Preparations Parts Icons Description This LED is power status indicator and works as •• Power On (Power button): Off Control Panel Power LED ――The color and shape of parts may differ from what is shown. Specifications are subject to change without the other position may cause wrong action. •• Power Off (Power button): On ――The power Indicator operation can be swapped by changing in the notice to improve quality.
Direct Key guide ――The shortcut button screen (OSD menu) shown below is displayed only when the monitor screen is turned on, the computer resolution changes, or the input source changes. ――The function buttons page shows if Eye Saver Mode is enabled. : On : Off Brightness Auto Adjustment Features Eye Saver Mode Off •• Press / button : Adjust Brightness, Contrast, Sharpness. •• Press / button : Adjust the screen settings automatically.
Function Key Guide ――To enter the main menu or to use other items, press the button to display the Function Key Guide. You can exit by pressing the Press / / / Press button: The selected item will be applied. button again. button: Move to the item you want. The description for each item will appear when the focus changes. Return Icons Description Selects to change the input signal by moving the changed. Selects by moving the button in the Function Key Guide screen.
When the monitor displays nothing (i.e. Power saving mode or Non-signal mode), 2 direct keys for control source and power could be used as below. Changing Brightness, Contrast and Sharpness settings DOME Type JOG Button When the shortcut button page is displayed, adjust the Brightness, Contrast and Sharpness from the initial screen using the DOME Type JOG Button.
Reverse Side Adjusting the Product Tilt ――The color and shape of parts may differ from what is shown. Specifications are subject to change without ――The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. notice to improve quality. -2.0° (±2.0°) ~ 20.0° (±2.0°) -1.0° (±1.0°) ~ 20.0° (±2.0°) (LS27E330HZ* / LS27E332HZ* models only) •• You can adjust the product tilt.
Anti-theft Lock ――An anti-theft lock allows you to use the product securely even in public places. ――The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details. The lock device is sold separately. To lock an anti-theft locking device: 1 Fix the cable of your anti-theft locking device to a heavy object such as a desk. 2 Put one end of the cable through the loop on the other end.
Installing a Wall-mount Kit or Desktop Stand ――Power the product off and remove the power cable from the power socket. 1 2 •• Notes ‒‒ Using a screw longer than the standard length can damage the internal components of the product. ‒‒ The length of screws required for a wall mount that does not comply with the VESA standards may vary depending on the specifications. ‒‒ Do not use screws that do not comply with the VESA standards. Do not attach the wall-mount kit or desktop stand using excessive force.
Installation Attaching the Stand ――Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards. ――The exterior may differ depending on the product. 1 Insert the stand neck into the stand base in the direction shown in the figure. 5 Insert the stand head into the connection hole in the direction, as shown in the figure. 2 Check that the stand neck is firmly connected.
Removing the Stand ――Before removing the stand from the monitor, place the monitor on a flat and stable surface with the screen facing down. ――The exterior may differ depending on the product. 1 Place a soft cloth over the table to protect the product and place the product onto the cloth so that the front of the product is facing downwards. 2 While holding the stand neck with one hand, pound the other fisted hand down onto the top of the stand base in the direction of the arrow to detach the stand base.
Chapter 03 Connecting and Using a Source Device Pre-connection Checkpoints Connecting and Using a PC ――Before connecting a source device, read the user manual provided with it. Select a connection method suitable for your PC. The number and locations of ports on source devices may differ from device to device. ――Do not connect the power cable before connecting all other cables. ――Connecting parts may differ in different products. ――Provided ports may vary depending on the product.
Connection Using the HDMI Cable HDMI IN Connecting the Power Power connection using integrated AC/DC adapter 1 Connection Using an HDMI-DVI Cable 2 HDMI IN 3 1 Connect the AC/DC adapter to the DC 14V port on the back of the monitor. 2 Next, connect the power cable to the power outlet. 3 Press the button on the back of the monitor to turn it on. ――The input voltage is switched automatically.
Power connection using detachable AC/DC adapter Correct posture to use the product 1 2 3 Use the product in the correct posture as follows: •• Straighten your back. •• Adjust the angle so light does not reflect on the screen. 1 Connect the power cable to the AC/DC adapter. Then, connect the AC/DC adapter to the DC 14V port on the back of the product. 2 Next, connect the power cable to the power outlet.
Driver Installation ――You can set the optimum resolution and frequency for this product by installing the corresponding drivers. ――To install the latest version of the product driver, download it from the Samsung Electronics website at http://www.samsung.com. Setting Optimum Resolution An information message about setting optimum resolution will appear if you power on the product for the first time after purchase. Select a language on the product and change the resolution on your PC to the optimum setting.
Chapter 04 Screen Setup Configure the screen settings such as brightness. A detailed description of each function is provided. Refer to your product for details. The functions available may vary depending on the product model. Refer to the actual product. Brightness Contrast You can adjust the general brightness of the picture. (Range: 0~100) Adjust the contrast between the objects and background. (Range: 0~100) A higher value will make the picture appear brighter.
Eye Saver Mode SAMSUNG MAGIC Bright Set to an optimum picture quality suitable for eye relaxation. This menu provides an optimum picture quality suitable for the environment where the product will be used. TÜV Rheinland “Low Blue Light Content” is a certification for products which meet requirements for lower blue light levels. When Eye Saver Mode is 'On', the blue light that wavelength is around 400nm will decrease, and it will provide an optimum picture quality suitable for eye relaxation.
SAMSUNG MAGIC Angle SAMSUNG MAGIC Upscale MAGICAngle allows you to configure the settings to obtain the optimum picture quality according to your viewing angle. MAGICUpscale function ――This menu is not available when SAMSUNG Bright is set to Cinema or Dynamic Contrast mode. ――This menu is not available when SAMSUNG Bright is set to Cinema or Dynamic Contrast mode. SAMSUNG MAGIC SAMSUNG can enhance the layers of the picture details and the vividness of the picture.
HDMI Black Level H-Position & V-Position If a DVD player or set-top box is connected to the product via HDMI, image quality degradation (contrast/ color degradation, black level, etc.) may occur, depending on the connected source device. In such case, HDMI Black Level can be used to adjust the image quality. H-Position: Move the screen to the left or right. If this is the case, correct the degraded picture quality using HDMI Black Level.
Chapter 05 Configuring Tint A detailed description of each function is provided. Refer to your product for details. Adjust the tint of the screen. This menu is not available when MAGICBright is in Cinema or Dynamic Contrast mode. This menu is not available when Game Mode or Eye Saver Mode is enabled. The functions available may vary depending on the product model. Refer to the actual product. SAMSUNG Red Green Adjust the value of the color red in the picture.
Color Tone Adjust the general color tone of the picture. •• Cool 2: Set the color temperature to be cooler than Cool 1. •• Cool 1: Set the color temperature to be cooler than Normal mode. •• Normal: Display the standard color tone. •• Warm 1: Set the color temperature to be warmer than Normal mode. •• Warm 2: Set the color temperature to be warmer than Warm 1. •• Custom: Customize the color tone.
Chapter 06 Resizing or Relocating the Screen A detailed description of each function is provided. Refer to your product for details. The functions available may vary depending on the product model. Refer to the actual product. Language Menu H-Position & Menu V-Position Set the menu language. Menu H-Position: Move the menu position to the left or right. ――A change to the language setting will only be applied to the onscreen menu display. Menu V-Position: Move the menu position up or down.
Chapter 07 Setup and Reset A detailed description of each function is provided. Refer to your product for details. The functions available may vary depending on the product model. Refer to the actual product. Reset All Eco Saving Plus Return all the settings for the product to the default factory settings. The Eco Saving Plus function reduces power consumption by controlling the electric current used by the monitor panel.
Off Timer Key Repeat Time Off Timer: Turn on Off Timer mode. Control the response rate of a button when the button is pressed. Turn Off After: The off timer can be set within a range of 1 to 23 hours. The product will automatically power off after the specified number of hours. Acceleration, 1 sec, or 2 sec can be selected. If No Repeat is selected, a command responds only once when a button is pressed. ――This option is only available when Off Timer is set to On.
INFORMATION View the current input source, frequency and resolution. PICTURE COLOR MENU SETTINGS SETUP&RESET INFORMATION INFORMATION LS********/** S / N : *************** Analog **kHz **Hz ** ****x**** Optimal Mode ****x**** **Hz ――The displayed image may differ depending on the model.
Chapter 08 Installing the Software Easy Setting Box System Requirements OS Hardware •• Windows XP 32Bit/64Bit •• At least 32MB of memory •• Windows Vista 32Bit/64Bit •• At least 60MB of free space on the hard disk drive •• Windows 7 32Bit/64Bit Easy Setting Box enables users to use the monitor by partitioning multiple sections. •• Windows 8 32Bit/64Bit To install the latest version of Easy Setting Box, download it from the Samsung Electronics website at http://www.samsung.com. •• Windows 8.
Chapter 09 Troubleshooting Guide Requirements Before Contacting Samsung Customer Service Center ――Before calling Samsung Customer Service Center, test your product as follows. If the problem persists, contact Samsung Customer Service Center. Check the following. Installation issue (PC mode) The screen keeps switching on and off. Check the cable connection between the product and PC, and ensure the connectors are locked.
Not Optimum Mode is displayed. Video playback is choppy. This message appears when the signal from the graphics card exceeds the maximum resolution or frequency for the product. Playback of high-definition large video files can be choppy. This may be because the video player is not optimized for the computer resource. Change the maximum resolution and frequency to suit the product performance, referring to Standard Signal Mode Table (P.37). Try playing the file on another video player.
Q&A ――Refer to the user manual for your PC or graphics card for further instructions on adjustment. How can I change the frequency? Set the frequency on your graphics card. •• Windows XP: Go to Control Panel Appearance and Themes •• Windows ME/2000: Go to Control Panel •• Windows Vista: Go to Control Panel •• Windows 7: Go to Control Panel Settings Appearance and Personalization System Control Panel Display Settings Advanced Appearance and Personalization •• Windows 8(Windows 8.
Chapter 10 Specifications General Model Name Size Display area S27E330H S27E332H 27 Class (27 Inches / 68 cm) 597.6 mm (H) x 336.15 mm (V) 23.5 Inches (H) x 13.2 Inches (V) Pixel Pitch 148.5 MHz 148.5 MHz (D-SUB) 174.5 MHz (HDMI) Power Supply AC100-240V~ 50/60Hz Based on the AC voltage of the adapter. For the DC voltage of the product, refer to the product label.
Standard Signal Mode Table Model Name Synchronization Resolution S27E330H Horizontal Frequency 30 – 81 kHz Vertical Frequency 56 – 75 Hz Optimum Resolution 1920 x 1080 @ 60 Hz Maximum Resolution 1920 x 1080 @ 60 Hz If a signal that belongs to the following standard signal modes is transmitted from your PC, the screen will automatically be adjusted. If the signal transmitted from the PC does not belong to the standard signal modes, the screen may be blank even though the power LED turns on.
Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA DMT, 1280 x 720 45.000 60.000 74.250 +/+ VESA DMT, 1280 x 800 49.702 59.810 83.500 -/+ VESA DMT, 1280 x 1024 63.981 60.020 108.000 +/+ VESA DMT, 1280 x 1024 79.976 75.025 135.000 +/+ VESA DMT, 1440 x 900 55.935 59.887 106.500 -/+ VESA DMT, 1600 x 900 RB 60.000 60.000 108.000 +/+ VESA DMT, 1680 x 1050 65.290 59.954 146.250 -/+ VESA DMT, 1920 x 1080 67.500 60.
Model Name Synchronization Resolution S27E332H Horizontal Frequency 30 – 81 kHz Vertical Frequency 56 – 75 Hz Optimum Resolution 1920 x 1080 @ 60 Hz (D-SUB) 1920 x 1080 @ 75 Hz (HDMI) Maximum Resolution 1920 x 1080 @ 60 Hz (D-SUB) 1920 x 1080 @ 75 Hz (HDMI) If a signal that belongs to the following standard signal modes is transmitted from your PC, the screen will automatically be adjusted.
Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA DMT, 1280 x 720 45.000 60.000 74.250 +/+ VESA DMT, 1280 x 800 49.702 59.810 83.500 -/+ VESA DMT, 1280 x 1024 63.981 60.020 108.000 +/+ VESA DMT, 1280 x 1024 79.976 75.025 135.000 +/+ VESA DMT, 1440 x 900 55.935 59.887 106.500 -/+ VESA DMT, 1600 x 900 RB 60.000 60.000 108.000 +/+ VESA DMT, 1680 x 1050 65.290 59.954 146.250 -/+ VESA DMT, 1920 x 1080 67.500 60.
Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA DMT, 1280 x 720 45.000 60.000 74.250 +/+ VESA DMT, 1280 x 800 49.702 59.810 83.500 -/+ VESA DMT, 1280 x 1024 63.981 60.020 108.000 +/+ VESA DMT, 1280 x 1024 79.976 75.025 135.000 +/+ VESA DMT, 1440 x 900 55.935 59.887 106.500 -/+ VESA DMT, 1600 x 900 RB 60.000 60.000 108.000 +/+ VESA DMT, 1680 x 1050 65.290 59.954 146.250 -/+ VESA DMT, 1920 x 1080 67.500 60.
Chapter 11 Appendix Responsibility for the Pay Service (Cost to Customers) A Product damage caused by customer's fault ――When the service is requested, in spite of in warranty, we may charge you for a visit from a service •• External impact or drop. technician in the following cases. Not a product defect Cleaning of the product, Adjustment, Explanation, Re-installation and etc. •• If a service technician gives instructions on how to use product or simply adjusts options without disassembling product.
