SADT - 104WM Wall Mount Adaptor imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please register your product at www.samsung.com/global/register SADT-104WM_ENG.
Overview The WALL MOUNT ADAPTOR is used to install the SMARTDOME CAMERA (SCC-C6433/C6435) in an indoor wall. ENG Notice • Make sure that you must select an installation spot to endure the total weight of "Wall Mount Adapter", "Smart Dome Camera". • This product is designed to use with anchor bolts and anchor nuts (M10). • If installing in a concrete wall, use a M10 anchor bolt (nut) with flat washer and spring washer. • Each installed anchor bolt should endure 700kg of pulling force.
. If you install the Wall Mount Adaptor in a wall, place the template on the wall and drill 4 holes for the anchor bolts (M10) and nuts (M10) before inserting them. If you install it in a corner of the wall, use the Corner Mount Adaptor (SADT-110CM). If installing on the pole of the wall, use the Pole Mount Adaptor (SADT-100PM). 150 mm TEMPLATE The positions for installing a ANCHOR BOLT 80 mm 4. Prepare the Camera Adaptor for the applicable camera. Remove the Bracket Sealing from the Camera Adaptor.
CAMERA ADAPTOR ENG 5. Remove the Connectors at the end of the Camera Adaptor. In the next step, peel off the coating of the cable and connect it to the external cable using soldering. (See the wiring diagram of the installation guide for the Camera to connect the cables.) Lastly, use an insulation tape to wrap up the soldering portion of two cables. Repeat the above steps to connect all of the 4 Connectors to the appropriate external cables.
6. Prepare the Camera Adaptor for the applicable camera. Refer to the installation guide for the applicable camera and configure the initial settings of the Camera Adaptor. (For more information, see the installation guide for the Camera) Insert the cable of the Camera Adaptor into the Wall Mount Adaptor before pulling it out throught the hole of the Cover Fixing Part. the place for joining a cover WALL MOUNT ADAPTOR CAMERA ADAPTOR 7.
8. Pull out cables such as external power cable, BNC cable and communications cable through the rear of the Wall Mount Adaptor, which are necessary for connecting the camera. ENG It is recommended to keep the cables about 100mm longer than the cover fixing part. the place for joining a cover 100mm WALL MOUNT ADAPTOR 9. Use the anchor bolts and nuts to secure the Wall Mount Adaptor to the wall. WALL MOUNT ADAPTOR ANCHOR BOLT CAMERA ADAPTOR SADT-104WM_ SADT-104WM_ENG.
10. Connect the cables of the Camera Adaptor with the outward cables, which then you push in through the Cover Fixing Part to the Wall Mount Adaptor. Insert one piece of the two-strand cable into an empty area of the Wall Mount Adaptor as in the figure below and push the other one into the Wall Mount Adaptor. CAUTION When you insert the cables into the Cover Fixing Part so that the insulation of the cable junction is not peeled off or torn.
12. Prepare the Camera Body. Put up the Safety Wire, attached to the camera, on the Safety Hook. ENG CAUTION To avoid accidental fall and consequent damage to the camera during installation or detachment, make sure the Safety Wire is secured to the hook. WALL MOUNT ADAPTOR WALL MOUNT ADAPTOR CAMERA ADAPTOR CAMERA ADAPTOR SAFETY HANGER SAFETY HANGER SAFETY WIRE SAFETY WIRE CAMERA CAMERA SADT-104WM_ SADT-104WM_ENG.
13. Align the Guide 1 of the Camera with the Guide 2 of the Camera Adaptor and insert the 3 Guides of the Camera into the corresponding Guide Holes of the Camera Adaptor. Then, turn the camera clockwise by 10 degrees. Make sure that the part "A" is moved from position 1 to 2.
14. Use the screws, attached to the Camera, to firmly fix the Camera body with the Camera Adaptor. (Once you removed the camera from the Camera Adaptor, loosen the screw, turn the camera counterclockwise by about 10 degrees, and then pull it down.) ENG CAUTION If you do not fix the screws, CAMERA BODY could be separated from the CAMERA ADAPTER due to the shake. To avoid safety accident and camera damage, make sure to fix the screws. WALL MOUNT ADAPTOR CAMERA SCREW SADT-104WM_ SADT-104WM_ENG.
Product Specification Location for use: Indoors Installation Spot: Wall or Vertical Structure Dimension: See the figure Weight: 241g Material: plastic Operation Temperature: -10˚C ~ 50˚C Ø 1 1 7 -Ø 1 0 ,5 4 Accessories Template .................................. 1 Cover ....................................... 1 MANUAL .................................. 1 10_SADT-104WM SADT-104WM_ENG.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.