4 CHANNEL DVR User Manual SDE-3004
4 Channel DVR User Manual Copyright ©2012 Samsung Techwin Co., Ltd. All rights reserved. Trademark is the registered logo of Samsung Techwin Co., Ltd. The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Samsung Techwin Co., Ltd shall reserve the copyright of this document.
overview IMPORTANT SAFETY INSTRUCTIONS OVERVIEW Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth.
overview CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
BEFORE START Warning ❖ Battery It is essential that when changing the battery in the unit, the replacement battery must be of the same type otherwise there may be a possibility of an explosion. The following are the specifications of the battery you are using now. • Normal voltage : 3V CALIFORNIA USA ONLY • Normal capacity : 170mAh This Perchlorate warning applies only to primary CR (Manganese Dioxide) Lithium coin cells in the product sold or distributed ONLY in California USA.
overview CONTENTS OVERVIEW 3 CONNECTING WITH OTHER DEVICE 13 LIVE 19 USING THE DVR 30 6_ overview 3 5 6 8 10 11 12 Important Safety Instructions Before Start Contents Features Part Names and Functions (Front) Part Names and Functions (Rear) Remote Control 13 13 13 14 14 17 Installation Checking the installation environment Connecting the Video, Audio, and Monitor Connecting the USB Connecting the Camera Connecting the Network 19 21 25 27 27 28 28 28 Getting Started Live Screen Configuration Live
SEARCH & PLAY 60 WEB VIEWER BACKUP VIEWER Search Playback 65 66 67 71 75 85 85 Introducing Web Viewer Connecting Web Viewer Using Live Viewer Using Search Viewer Viewer Setup About Mobile Viewer 86 SEC Backup Viewer 88 89 91 94 96 Product Specification (Camera) Product Specification Default Setting Troubleshooting Open Source License Report on the Product OVERVIEW 65 60 63 86 APPENDIX 88 English _7
overview FEATURES The DVR employs H.264 video encoding for 4 channel inputs and audio encoding for 1 channels while simultaneously supports hard disc recording and playback. These DVRs also supports network connectivity, providing remote monitoring from a remote PC transferring video and audio data.
Standards Approvals M This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 Package Contents Please unwrap the product, and place the product on a flat place or in the place to be installed. Please check the following contents are included in addition to the main unit.
overview PART NAMES AND FUNCTIONS (FRONT) DIGITAL VIDEO RECORDER POWER REC bc Part Names Functions USB Port Connects the USB devices. b Remote Control Receiver Input the remote control signal. c LED Indicator Power LED : Displays the power ON/OFF status. 10_ overview REC : Lights on when recording is in progress.
PART NAMES AND FUNCTIONS (REAR) b c AUDIO IN NETWORK 1 2 DC 12V 1 ALARM IN 2 3 4 G ALARM OUT 1 COM G CONSOLE 3 4 AUDIO OUT b c M USB VGA Part Names OVERVIEW VIDEO OUT Functions CAMERA IN Video Signal input ports (BNC type connector). VIDEO OUT Video Signal Output Port (RCA jack). AUDIO IN Audio input signal port (RCA jack, CH1). NETWORK NETWORK connector port. DC 12V DVR power input port. USB USB connector port. VGA VGA Video Signal Output Port.
overview REMOTE CONTROL BACKUP SEARCH Displays the search menu. Displays the Backup Menu. MODE Changes the screen mode. DVR Activates the DVR function. POWER Displays the Exit pop up screen. NUMBER [0~+10] Used as the numeric input keys, or displays a single channel. ID Sets the ID of the system. Select 2 digits from 0 ~ 9 while pressing the ID Key. Skip Backward (by unit time), Slow Rewind, Slow Forward, Skip Forward (by unit time) Move Frame While paused, moves to the previous/next frame.
connecting with other device INSTALLATION Please take note of the followings before using this product. Do not use the DVR outdoors. Do not spill water or liquid in the connection part of the product. Do not impose the system to excessive shock or force. Do not pull out the power plug forcefully. Do not disassemble the product on your own. Do not exceed the rated input/output range. Use a certified power cord only. For the product with an input ground, use a grounded power plug.
connecting with other device CONNECTING THE USB 1. By factory default, a USB port is provided for external connection. 2. You can connect a USB HDD, USB memory or mouse to the USB port. 3. If a USB HDD is connected to the system, recognition and settings are available in “Menu > Setting the Device > Storage Device”. (Page 41) 4. This product supports hot-plugging, which connects/removes the USB device during the system operation.
Connecting with DVR TO DVR SIDE O AUDI O IN NLY VIDEO OUT ALA 1 2 RM IN 3 4 O OU T ALA G 1 RM OUT COM G NETW ORK VGA DC 12 V CONS OLE USB TO CA MERA SIDE O NLY Installing the camera The camera can be installed on the wall, ceiling, shelf or a desired position using the provided bracket. 1. Select a position where you want to install the camera. Make sure the selected position can sustain the weight of the camera. 2. Use the screw bolts (M3.
connecting with other device Adjusting the Camera Bracket 1. Choose an installation site that can sufficiently support the weight of the equipments to be installed. 2. Attach the camera bracket to the wall using the supplied screws (M3.5 X L25). 3.5 X 25 sized screws wall or ceiling. 3. Adjust the camera to target the video location and tighten the camera bracket handle on the camera bracket. Install the camera on to the male screw of the camera bracket by rotating the camera clockwise. 4.
CONNECTING THE NETWORK Connecting to Network through Ethernet (10/100BaseT) CONNECTING WITH OTHER DEVICE AUDIO IN VIDEO OUT AUDIO ALA 1 2 RM IN 3 4 OUT ALA G 1 RM OUT COM G NETW ORK VGA DC 12 CONS V OLE NETWORK Back B one RJ-45 Ethernet Cable (Direct Cable) USB Hub/Switcher Hub/Switcher Windows Network Viewer Connecting to the Network using the router AUDIO IN VIDEO OUT AUDIO ALA 1 2 RM IN 3 4 OUT ALA G 1 RM OUT COM G NETW ORK VGA DC 12 CONS xDSL or Cable Modem V OLE USB B
connecting with other device Connecting to Internet through ADSL AUDIO IN VIDEO OUT AUDIO ALA 1 2 RM IN 3 4 OUT ALA G 1 RM OUT COM G NETW ORK VGA DC 12 CONS V OLE INTERNET RJ-45 Ethernet Cable (Direct Cable) Phone(A DSL) Lin e Hub/Switcher Windows Network Viewer 18_ connecting with other device USB ADSL MODEM
live GETTING STARTED Starting the system M LIVE 1. Connect the power cable of the DVR to the wall outlet. It takes about 10 seconds to display the start screen after booting. 2. You will see the initialization screen. The initialization process will last about 1 minute. If a new HDD is installed, the initialization process may take longer. 3. The live screen appears with a beep.
live Login To access a DVR or restricted menu, you should have logged in to the DVR. 1. In live mode, right-click any area of the screen. You will see the context sensitive menu as in the right figure. Scene Mode 2012-01-01 01:10:25 Spot Out Audio Off Freeze Stop Alarm Record Play Search Backup Main Menu Shutdown Hide Launcher Login 2. Click . The login dialog appears. You can also see the login dialog to access a desired menu by pressing the [MENU] button on the remote control.
LIVE SCREEN CONFIGURATION Icons on the Live Screen You can check the status or operation of the DVR with the icons on the live screen. 2012-01-01 01:10:25 LIVE CAM 01 Name b Description Current Date, Time Displays the current time and date. Login Information When you are logged in, the “LOG ON” icon will be displayed. Displayed if the zoom function is activated. Displayed if you press the Pause button.
live Error Information • If the internal HDD is not connected, the “NO HDD”( ) message will appear; if there occurs a problem, ) message in the top left corner. In this case, make sure you contact the you will see the “HDD FAIL”( service center for assistance as this may cause a failure of recording, playback or backup. M If you see the No HDD, HDD FAIL icons on the screen, contact the service center for more details.
Menu m Scene Mode Refer to “Live Mode”. (Page 25) Spot Out Refer to “Spot Out”. (Page 27) Audio On/Off Refer to “Audio ON/OFF”. (Page 28) Freeze Refer to “Freeze”. (Page 28) Stop Alarm Stops the alarm output and the event monitoring. Refer to “Event Monitoring”. (Page 28) Record/Stop Starts/stops the standard recording. Play Refer to “Search & Play > Play”. (Page 63) Search Refer to “Search & Play > Search”. (Page 60) Backup Refer to “Using the DVR > Setting the Backup”.
live View the Launcher Menu The Launcher menu appears on the bottom of the live screen. 1. In Live mode, right-click to display the context menu and select . 2012-01-01 01:10:25 2. Move the cursor to the bottom and click a desired item in the Launcher menu. M If no input is entered for 10 seconds, the menu will disappear. The Launcher menu can be accessed only by using the mouse.
LIVE MODE Displays 4 live video images in 3 different modes. Switching the screen mode CH1 CH2 CH3 CH4 CH2 CH1 CH1 4-split mode PIP Auto Sequence Switching the screen automatically You can display 4 live single screens in sequence. 4 CH1 CH1 CH1 CH1 Single mode M 1 In Single mode, If you have set in “Setting the Device > Camera”, Auto Sequence will be conducted at the set interval.
live Channel Setting You can display the channel in a desired area of a split screen. 1. Click a camera name to display a channel list where you can select a different channel. 2. Select a desired channel and click it. The current channel will be switched to the selected one. Use the cursor to select a channel to move, and drag and drop it to a desired channel; this can also change the channel position.
SPOT OUT The Spot Out monitoring is independent of the Live mode, which monitors a specific channel through the Spot Out port. Selecting a Spot Out mode Scene Mode Spot Out Audio Off 2. Click Spot Out. Supports the Spot output in Single screen with Auto Sequence mode. The Spot output is supported only for a designated channel. For the Spot Out port of a model, refer to “Part Names and Functions (Rear)”.
live AUDIO ON/OFF You can turn the sound on/off the CH1 in Live mode. AUDIO ON/OFF in Single mode Click the audio icon ( M ) on the screen, or press the [AUDIO] button on the remote control to turn it on/off. Only the channel where
Ex : If you set to 5 seconds, and the second event occurs in CH 2 within the set time after the first event occurred in CH 1. Event occurrence 4 seconds 9 seconds CH1 LIVE Stop alarm CH2 CH1 M Press the [ALARM] button to reset the alarm settings and to release the event mode. If an alarm activates in the condition you have set the event record, and pre/post alarm times, the event record will be performed.
using the DVR You can setup the system properties, devices, and options for recording, event, backup and network. SYSTEM SETUP You can setup Date/Time/Language, Permission, System Properties and Log. Date/Time/Language You can check and setup the current Date/Time and time related properties, as well as the language used for the interface on the screen. Setting the Date/Time/Language Set the Date/Time/Language Using the mouse may help make setup easier. 1. Press the [MENU] button on the remote control.
- Time Server : Enter an IP or URL address of the time Date/Time/Language server. Date/Time/Language Holiday - Last Sync Time : Displays the most recent Time Synchronization Setup synchronization time from the selected time server. - Activate as Server : Set to
using the DVR Permission Management You can set permissions of each user over the DVR's specific function and settings. Setting the Administrator You can set and change Administrator’s ID and password. The administrator can use and set all menu items and functions. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. Permission Management Admin Group ID 2. Select .
Setting the Group You can create user groups and setup permissions for those user groups. You can register a user for each group in . Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. Group Admin User Group • Add Setup Delete Rename Group Authority Live View Setup Search Setup Backup Setup USING THE DVR 2. Select .
using the DVR To restrict the user permissions If the admin restricts all permissions of an added group, the users belonging to that group can access only the default minimum menus and can change the user’s own password only. 1. Start the DVR. If all permissions are restricted, only the Login dialog should appear. 2. Log in with a registered user ID. Login ID abc Password OK 3. Right-click any area on the screen. If all permissions are restricted, only the accessible context menus should appear.
Setting the User Users can be added only if a group was created in menu. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. Permission Management Admin Add Name ID Viewer Delete Previous/Next Page OK Cancel Permission Management Admin Group Group Name • Viewer : If you select
using the DVR • Manual Input of ID : Prompts you to enter the user ID manually for the login process. - Checked ( ) : Encloses the registered user IDs with the [] symbols. Use the virtual keyboard to enter the user ID. Login ID ***** Password 4. When the permission setup is done, press . OK Cancel System Management You can check the system version, update to a newer version, as well as data backup and initialization.
• Updating the Software 1. Connect a device storing the software to be updated. (It may take about 10 seconds to recognize the device.) Upgradeable devices include USB memory and network device. To update the network, the current DVR should have been connected to the network. Upgrade via the proxy server may not be enabled due to the restricted access. System Management System Information • Settings System Information Software Version System Format Broadcast v1.
using the DVR Settings You can copy and import the DVR settings by using a storage media. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. System Management Settings System Information Storage Device 2. Select . A window of storage device and load factory default appears.
Event Log Event log shows recorded events on alarms, motion detections and video loss. It also shows the log and its timestamp. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. 2. Select . Log Information System Log Search Day First Page 4. Set Search Day, Channel and Type and the press . Last Page CH All CHs Type View all No.
using the DVR SETTING THE DEVICE You can setup Camera, Storage Device, Remote Device and Monitor. Camera Setting the Camera You can set Video, Audio, Channel Name and Dwell Time of a Camera. Using the mouse may help make setup easier. 1. Press the [MENU] button on the remote control. Logout Return 2. Use the left/right button (◄ ►) to select . Device setting menu is selected. Device 3. Use the up/down buttons ( ) to move to , and press [ENTER] button.
• CH Name : Up to 15 characters including blanks are allowed. (The first character should not be empty.) Refer to “Using Virtual Keyboard”. (Page 32) • SEQ-Dwell Time : You can set the dwell time between channels for the Live screen and Spot Out. If set to , the channel is not listed in the Auto Sequence mode. • Press the to initialize settings back to the default 50. 6. When the camera setup is done, press .
using the DVR Formatting You can format a storage device. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. 2. Select . A window for selection of device for formatting appears. Storage Device Format Device Device HDD HDD Alarm Select 1 Used/Total Used 6.07G/495.02G Internal 3. Use direction buttons ( ◄ ►) to select a device to be formatted. Format OK 4.
HDD Alarm You can set alarm settings for HDD defects such as Check Alarm Output Port, Replace Alarm Output Port, and its duration. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. Device HDD Alarm Format Check Alarm Output Port Duration BEEP OFF Replace Alarm Output Port Duration BEEP OFF 3. Use direction buttons ( ◄ ►) to move to the desired item.
using the DVR Monitor You can select which item(s) to be displayed on the screen. Setting the Monitor Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. 2. Select . 3. Use direction buttons ( ◄ ►) to move to a desired item, and set the value. • Event Display : Sets the dwell time of the event channel display on the monitor when an event occurs.
Setting the Spot Out You can set the DVR to output information / video apart from the monitor out. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. 2. Select . The number of Spot Out terminals differs according to the Monitor Spot Out Monitor Spot Out 1 SEQ Event Display OFF Mode All Set Mode USING THE DVR model. 3.
using the DVR SETTING THE RECORDING You can setup scheduled recording, event recording and other recording related settings. Recording Schedule Make your reservation on a date and time to schedule the recording on specified time. Using the mouse may help make setup easier. 1. Press the [MENU] button on the remote control. Logout 2. Use the left/right button (◄ ►) to select . Record menu is selected. 3. Use the up/down buttons ( ) to move to , and press [ENTER] button.
Recording Color Tags Color Function White No Recording Orange Continuous Blue Event Green Both(Cont&Evnt) Description No schedule / event recording Scheduled recording only Event recording only Both scheduled / event recordings USING THE DVR Each press of a selected cell will cycle through --. Event Record Duration You can set the beginning and ending point of a recording on an event. Using the mouse may help make setup easier. 1.
using the DVR Setting Event Recording Properties You can set each channel’s resolution, quality and fps for event recordings. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. REC Quality & Resolution Event Standard Remaining count : 4CIF(L) : 2 CH 2. Select . Event recording setup window appears.
SETTING THE EVENT You can set recording options for motion and video loss event. Motion Detection You can set target detection region and motion, as well as the alarm signal output. When the motion detection region is set, it detects motion within the area. 1. Press the [MENU] button on the remote control. Logout Return 2. Use the left/right button (◄ ►) to select . Event setting menu is selected. Event Motion Detection Video Loss Detection Alarm Schedule 3.
using the DVR Setting the Motion Detection Area Select . When “Motion Region” window appears, select a channel for detection and set the area of motion detection. • To set the area in “Motion Region” window In the “Motion Region” window, select desired region from < >. Motion Region CH1 Individual • To set the area using selection OK Apply to All CH Cancel In the “Motion Region” window, you can select cells individually by using .
Alarm Schedule You can set the conditions and operating hours for scheduled alarms. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. Alarm Schedule BEEP 2. A window of settings appears. 3. Alarm : Sets the alarm output method. Alarm”.
using the DVR BACKUP You can check the backup device and set the backup schedule by channel or by time. The product only supports external HDD of USB memory and USB type. (Page 89) Setting the Backup You can backup the desired data to a connected device. Using the mouse may help make setup easier. 1. Press the [MENU] button on the remote control. Logout 2. Use the left/right button (◄ ►) to select . Backup menu is selected. Return Backup Backup 3. Press the [ENTER] button.
5. When the backup setup is done, press . If no available device is recognized for backup, button is not activated. J The application may slow down during the backup. You can switch to the menu screen during the backup in operation, but playback of data is not available. If backup has failed, select “Device > Storage Device” and check the free space of the HDD and check also if the HDD is properly connected.
using the DVR • IP, Gateway, Subnet Mask, and DNS - For : You can directly input IP address, Gateway, Subnet Mask and DNS. - For : IP address, Gateway, and Subnet Mask are set automatically. - For : IP address, Gateway, and Subnet Mask are set automatically. • User ID, Password : In case you selected ADSL, provide the “User ID” and its “Password”. M Connection Mode Connection Protocol Connection Mode ADSL Bandwidth 600kbps IP 192.168. 1.200 Gateway 192.168.
Connecting and Setting the Network Networking may differ from the connection method, check your environment before setting the connection mode. When no router is used • Static IP mode - DVR Network Settings : Set the in menu of the connected DVR to . Consult your network manager for IP, Gateway and Subnet Mask. • Dynamic IP (DHCP) mode - Internet connection : Connect the DVR directly to a cable modem, DHCP ADSL modem or FTTH network.
using the DVR When a router is used J To avoid IP address conflict with the DVR's static IP, check followings : • Setting the DVR with a static IP - Internet connection : You can connect the DVR to a router which is connected to an ADSL/Cable modem or a router in a Local Area Network (LAN) environment. • Setting the DVR Network 1. Set the in menu of the connected DVR to . 2.
DDNS You can set the DDNS site for a remote user’s network connection. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. DDNS DDNS Site 2. Use virtual keyboard to enter user inputs. Refer to “Using Virtual Keyboard”. (Page 32) iPOLiS Host Name www.samsungip... User Name SDE-3004_HOME User Password http://www.samsungipolis.
using the DVR Mailing Service You can send an e-mail to a DVR-registered user at a specific time interval, or if an event occurs. M If an event occurs with a channel where the camera’s video is set to or the remaining recording count is set to , only the text notification will be sent to the applicable email address. SMTP Setting Sets the SMTP mail server. Using the mouse may help make setup easier. 1.
Group Setting You can set the group to whom the e-mail is sent, and specify the permission for each group. You can add recipients for each group in the menu item. The recipient is set separately from the DVR user group. Using the mouse may help make setup easier. 1. In the setting window, press the up/down ( ) button to move to and press the [ENTER] button. 3. Use direction buttons ( ◄ ►) to move to a desired item and set the value.
search & play SEARCH You can perform the search for recorded data by the time or by the search criteria such as an event. You can access the menu directly in Live mode. 1. In Live mode, right-click any area of the screen. The Live menu appears. Scene Mode 2012-01-01 01:10:25 Spot Out Audio Off Freeze 2. Select . Or, press the [SEARCH] button on the remote control. Stop Alarm Record Play Search Backup Main Menu Shutdown Hide Launcher Logout 3. The Search menu appears.
• Zoom In : The map enlarges in detail. It will switch in the sequence of 24 hours - 16 hours - 8 hour - 4 hours. • Zoom Out : The map will switch in the reverse order of the detailed mode above. It will switch in the sequence of 4 hours - 8 hour - 16 hours - 24 hours. Time Search Go to First 2012-01-01 Go to Last Overlapped Data List1 Zoom In Zoom Out 00:01 All Data CAM 01 CAM 02 CAM 03 2012/01/01 00:01:17 CAM 04 Standard Schedule Motion Etc V.
search & play Motion Search If a motion is detected in each channel, you can set a desired area to perform the search. You can use the mouse to select the related items. 1. Select in the menu. 2. Use direction buttons ( ◄ ►) to set the search criteria and press the [ENTER] button. If you set the motion area to , the Motion Search Channel CAM 01 Date/Time 2012-01-01 03:41:18 Overlapped Data Motion Region List1 Go to First No.
PLAYBACK Play You can play data stored in the HDD and backup a desired portion of the data. Using the mouse may help make setup easier. 1. In Live mode, click in the right-click menu or < > in the launcher menu, or press the Play button on the remote control. Scene Mode 2012-01-01 01:10:25 Spot Out Audio Off SEARCH & PLAY Freeze Stop Alarm Record 2. Use the up/down button ( ) to select a menu. Play For data search, refer to .
search & play Using the Playback Button REC Part Names Functions Play Timeline Indicates the current playback point, and can be used to move. b Skip Backward Moves backward by unit time. c Backward Fast Play Used for quick backward search while in Play. Backward Slow Play Used for backward frame-by-frame search while in PAUSE. Step Backward Moves backward by one frame at a time. Pause Stops playing the current video temporarily.
web viewer INTRODUCING WEB VIEWER What is Web Viewer? WEB VIEWER Web Viewer allows remote access to your DVRs. You have access to live video, archived video etc. PRODUCT FEATURES • Remote access from a standard browser • Supports 1, 4 camera viewing formats (maximum of 4 cameras in the list). • Gets JPEG, BMP format images to print and save to “Print or Save JPEG, BMP format images”. • Record video in AVI format-compatible with popular media players. (needed the H.
web viewer CONNECTING WEB VIEWER 1. Open your web browser and type the IP address or URL of DVR into the URL address box. M The basic URL of the DVR is as following in case of MAC address : http://www.samsungipolis.com/User ID You can also use registered URL which setups up in the Setup menu of your DVR. 2. Set the Admin ID and password same to those of the DVR Admin. For general users, enter the DVR user ID and password.
5. You may have “Windows Security Alert” that attempts to block this with the Windows Firewall. In that case, click to start Web Viewer. 6. Installation is complete. Now you can see the main screen of Live Viewer. WEB VIEWER USING LIVE VIEWER The Live Viewer screen consists of following : This displays the IP address and the model name of the connected DVR. b These menus consist of , , , . c These buttons are used for the screen split and full screen mode.
web viewer OSD INFORMATION DISPLAY The channel number, video size, and IP address of the connected DVR are displayed. b The current date and time will be displayed according to the selected time information display setting or . c Motion icon appears when motion is detected. It disappears when pressed the [ALARM] button of the DVR. b SPLIT-SCREEN You can change the split mode by clicking each number icon. SINGLE MODE QUAD MODE • Click < > button.
CONNECTED DVR This displays the IP address and the status of the connecting DVR. M Connection failure message No Response : Appears when the DVR does not respond. Access Denied : Appears when the maximum number of users is exceeded. The number of simultaneous connections are limited to 4. WEB VIEWER Setting the display of the OSD time information Select or for the OSD time information display setting.
web viewer SAVING THE LIVE SCREEN ON THE PC • CAPTURE : Saves the current screen into a BMP or JPEG file. M The default saving path is “C:\Program Files\Samsung\Dvr Web Viewer\SnapShot\Live”. To change the saving path, click button and then select the path you want. For Windows Vista or 7, the saving path is “C:\users\ (user ID)\AppData\LocalLow\Samsung\DVR Web Viewer\ SnapShot\” by default.
USING SEARCH VIEWER WEB VIEWER The Search Viewer screen consists of following : This displays the IP address and the model name of the connected DVR. b There are 4 tabs available: , , , . c Switch to a split mode. Shows the IP address and model name of the connected DVR. Select to turn the sound on/off. These buttons are used for capture, print, and save the image. This displays a calendar at which you can search the recorded video.
web viewer SPLIT-SCREEN You can change the split mode by clicking each number icon. SINGLE MODE QUAD MODE > button. • Click < The screen displays the selected camera connected to the DVR in “SINGLE MODE”. • Click < > button. The screen displays the selected camera connected to the DVR in “QUAD MODE”. CONNECTED DVR The IP of the connected DVR will be displayed. Select to turn the sound on/off. M Connection failure message No Response : Appears when the DVR does not respond.
SAVING THE LIVE SCREEN ON THE PC • CAPTURE : Saves the current screen into a BMP or JPEG file. M The default saving path is “C:\Program Files\Samsung\Dvr • PRINT : Print out the current screen. It also prints IP address, time, camera number and current event state. • RECORD : While in playback, press this button saves the video data of the selected channel as an AVI file. (It is saved in the designated folder on your PC.) To stop recording, click this button again.
web viewer SEARCHING THE RECORDED VIDEO IN THE CALENDAR If the video data has been recorded on a date, the date is distinguished in green. If you click the date, the recorded video information is displayed in the time line. When you click , it will be synchronized with the system time (date) of the current PC. SEARCHING THE RECORDED VIDEO IN THE TIMELINE It displays the recorded video data status on the DVR after a date is selected.
CONTROLLING PLAYBACK WEB VIEWER Fast Backward : Reverse-plays faster(2x~64x). b Reverse Play : Performs Reverse Play. c Play : Performs playback. Fast Forward : Plays faster(2x~64x). Go to First : Moves the beginning time of recorded video in the time line. Step Backward : Performs one step reverseplay by one frame. Pause : Stops the playback temporarily. Step Forward : Performs one step forward by one frame. Go to Last : Moves the last time of recorded video in the time line.
web viewer • Time Synchronization Setup Set the time synchronization. • Display Date Format : Set the date type. Time : Select a time format to display on the screen. • DST (Daylight Saving Time) DST is displayed an hour ahead of the standard time of the time zone. • Language Select a preferred language for the DVR. Holiday You can set specific dates to Holidays according to your preferences. For more information, refer to in the menu.
• Group Users are classified into groups and the permission can be set according to the group. First of all, add a group. WEB VIEWER • User You can add, change or remove a user or users. • Setup You can set the user permission. System Management For more information, refer to in the menu. (Page 36) • System Information You can see information of the current system. Check the software version, broadcast format and MAC address.
web viewer Device You can check a list of devices that are connected to the DVR and configure the necessary settings. Click in the menu screen. For more information, refer to “Setting the Device”. (Page 40) Camera • Camera You can configure the settings of the camera that is connected to the DVR. Storage Device You can check and change the settings of the storage device. • Device You will see a list of storage devices that are connected to the DVR.
Remote Device Specify the use of remote control and the remote control ID so that you can synchronize with the DVR. WEB VIEWER Monitor • Monitor You can configure the monitoring screen settings and set the output system. • Spot Out With the monitor connected via the SPOT port, if there occurs an event such as Motion or Alarm, you can select a video output mode for external monitoring. • Mode You can switch between live mode and play mode.
web viewer Record For more information, refer to . (Page 46) Recording Schedule If you set a recording schedule for a specific date and time, the recording will start at that specific time. - Apply to All CH : Click to display the confirmation window. Event Record Duration You can set the start and end times of recording that will be activated if an event occurs.
REC Quality & Resolution • Standard/Event You can set the resolution, frame rate and recording quality for each channel. WEB VIEWER Record Option You can set the Disk End Mode. Event For more information, refer to . (Page 49) Motion Detection You can set the motion detection mode and the sensitivity as well as the alarm output type and the duration.
web viewer • Motion Region Set the target motion detection area Video Loss Detection You can set the alarm output time if a video loss occurs. Alarm Schedule You can schedule the alarm output according to the day of the week and the time. The default setting is Event Sync, which activates the alarm only if an event occurs.
Network For more information, refer to . (Page 53) Connection A remote user can access the DVR via the network to check the current mode and the IP address. • Connection WEB VIEWER You can set the network connection route. • Protocol You can configure the protocol related settings. DDNS You can check the DDNS settings. Live Transfer A remote user can set the images of the DVR. • Live Transfer A remote user can set the image resolution of the transferred data.
web viewer Mailing Service You can specify the SMTP server that sends a mail if an event occurs and set the recipient group and users. • SMTP You can set the server that sends mails and specify if you use the authentication process. • Event You can set the event interval and specify which events the server sends mails for. • Group You can add a group to receive the mail if an event occurs and set the permission to receive the event mail for each group.
ABOUT Click . Displays the model name of connected DVR and the version of Web Viewer. WEB VIEWER MOBILE VIEWER What is Mobile Viewer? iPOLIS mobile is smartphone application that enables you to connect to DVR (Digital Video Recorder) remotely and control the video playback and PTZ operations (if configured) in real time. Key Features 1.X • Remote access via Smartphone • 1-split and 4-split modes supported in Live Viewer (However, search is not available).
backup viewer SEC BACKUP VIEWER You can play a file that is backed up in the format of SEC. Backup in the format of SEC will involve in generating two files: one for the backup data and one for the viewer. If you run the backup file viewer, the backup data file will be automatically played. Recommended System Requirements PCs with a lower specification than the recommended below may not fully support forward/backward and high-speed playback.
Name Description / A toggle button. Each time you press this button, the audio output will toggle between activated and deactivated. Audio You can adjust the volume level from 0 to 100. c Screen Printout Prints out the current screen. You should have installed the appropriate printer driver before you can print out the screen. File Tamper Detection / Deinterlace A toggle button. Each time you press this button, it will toggle between activated and deactivated.
appendix PRODUCT SPECIFICATION (CAMERA) Details Item SEB-1020R N SEB-1020R P Electrical Input Voltage DC 12V Power Consumption 3W Video Imaging Device 1/3.6’’ OV7959 Color CMOS Total Pixels PAL: 668(H) x 528(V) NTSC: 648(H) x 488(V) Scanning System Interlace Synchronization Internal H : 15,734 Hz H : 15,625 Hz V : 59.94 Hz V : 50 Hz Frequency Horizontal Resolution 480TVL Min. Illumination OLux (IR-LED) S/N Ratio (Y Signal) 46dB Lens Focus Length 3.6mm Max.
PRODUCT SPECIFICATION Design and specifications are subject to change without prior notice. Item Details Inputs 4 composite video 0.5-1 Vpp, 75 ohm Resolution 704x480 NTSC, 704x576 PAL Frame rate 30fps NTSC, 25fps PAL Resolution 704x480 NTSC, 704x576 PAL Multi Screen display 1, 4, PIP Embedded Linux Compression H.
appendix Item Details Interface Monitors Audio VGA Analog RGB 1024x768 resolution (BNC or VGA selected in booting.) HDMI – Main Composite BNC, 1 Vp-p, 75 ohm Spot Composite – Loop Outputs – Inputs/Output 1 Line in(CH1) / 1 line out Compression G.711 Sampling rate 8KHz Inputs/Outputs – Remote notification Notification via e-mail Ethernet 1 RJ45 10/100 Base-T Serial interface – USB USB 2.
DEFAULT SETTING This returns the factory default settings. The settings are made as follows; • Use System/Load Factory Default in MENU The default password can be exposed to a hacking thread so it is recommended to change the password after installing the product. Note that the security and other related issues caused by the unchanged password shall be responsible for the user.
appendix Category Details Recording Schedule Channel 1 Event Event Record Duration PRE Event OFF POST Event Normal Recording Recording REC Quality/ Resolution Event Record Option Motion Detection Event Video Loss Detection Alarm Schedule 92_ appendix Factory Default Disk End Mode 1 min Resolution CIF(S) Frame Rate NTSC: 7 fps, PAL: 5 fps Record Quality Level 4 Resolution 4CIF(L) Frame Rate NTSC: 7 fps, PAL: 5 fps Record Quality Level 4 Setup Overwrite Disk End Beep OFF Auto
Category Details Connection Connection Mode Network DDNS Live Transfer Connection Mode Static IP Bandwidth 2Mbps IP 192.168.1.200 Gateway 192.168.1.1 Subnet Mask 255.255.255.0 DNS 168.126.63.
appendix TROUBLESHOOTING Symptom Countermeasures The system does not turn on and the indicator on the front panel does not work at all. Check if the power supply system is properly connected. Check the system for the input voltage from the power source. If the problem persists even after you have taken the above actions, check the power supplier and replace it with a new one if neccessary. Some channels display just a black screen even if they receive video sources.
Symptom Countermeasures See the compatibility list of external storage devices to check if the connected device is supported by the DVR. For the compatibility list, contact the retailer where you purchased the DVR. If I press the ESC key in full screen mode of the WebViewer, the system does not switch to a normal split mode. Press the ALT+TAB keys to select ‘ACTIVE MOVIE’ and press the ESC key again. The system will switch to a normal split mode.
OPEN SOURCE LICENSE REPORT ON THE PRODUCT The software included in this product contains copyrighted software that is licensed under the GPL/LGPL. You may obtain the complete Corresponding Source code from us for a period of three years after our last shipment of this product by sending email to help.cctv@samsung.com If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source distribution might be charged.
normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
Preamble The GNU General Public License is a free, copyleft license for software and other kinds of works. The licenses for most software and other practical works are designed to take away your freedom to share and change the works. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change all versions of a program--to make sure it remains free software for all its users.
5. Conveying Modified Source Versions. You may convey a work based on the Program, or the modifications to produce it from the Program, in the form of source code under the terms of section 4, provided that you also meet all of these conditions: a) The work must carry prominent notices stating that you modified it, and giving a relevant date. b) The work must carry prominent notices stating that it is released under this License and any conditions added under section 7.
8. Termination. You may not propagate or modify a covered work except as expressly provided under this License. Any attempt otherwise to propagate or modify it is void, and will automatically terminate your rights under this License (including any patent licenses granted under the third paragraph of section 11).
16. Limitation of Liability.
d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.
so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Library.
(online or textual) provided with the package.Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer. 2.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.
SALES NETWORK SAMSUNG TECHWIN CO., LTD. Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400 TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. 100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660 Toll Free : +1-877-213-1222 Direct : +1-201-325-6920 Fax : +1-201-373-0124 www.samsungsv.com www.samsungtechwin.com www.samsungsecurity.com www.samsungipolis.com SAMSUNG TECHWIN EUROPE LTD.
