Install drivers Install programs SyncMaster 740B / 940B / 740N / 940Fn / 540B / 540N / 740T / 940T / 940N / 940Be
Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock Power When not used for an extended period of time, set your computer to DPMS. If using a screen saver, set it to active screen mode.
Do not use a damaged or loose plug. z This may cause electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. z This may cause electric shock or fire. Use only a properly grounded plug and receptacle. z An improper ground may cause electric shock or equipment damage. Insert the power plug firmly so that it does not come loose. z A bad connection may cause fire.
Installation Be sure to contact an authorized Service Center, when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc. Failure to do so may cause serious damage to your monitor. Place your monitor in a location with low humidity and a minimum of dust. z Failure to do so may cause electric shock or fire inside the monitor.
Put down the monitor carefully. z Failing to do so may damage the monitor. Do not place the monitor face down. z This may damage the TFT-LCD surface. The installation of the bracket must be done by a qualified professional. z z Installing the bracket by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual. When installing the product, make sure to keep it away from the wall (more than 10 cm / 4 inchs) for ventilation purposes.
Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. z A dirty connector may cause electric shock or fire. Make sure to unplug the power cord before cleaning the product. z Otherwise, this may cause electric shock or fire. Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth.
If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact a Service Center. z The monitor may malfunction, causing electric shock or fire. Disconnect the plug from the outlet during storms or lightning or if it is not used for a long period of time. z Failure to do so may cause electric shock or fire. Do not try to move the monitor by pulling only the wire or the signal cable.
Do not insert metal objects such as chopsticks, wire and tools or inflammable objects such as paper or matches into the vent, headphone port or AV ports. z This may cause electric shock or fire. If an alien substances or water enters the product, turn the product off, unplug the power connector from the wall outlet and contact a Service Center. When viewing a fixed screen for an extended period of time, residual image or blurriness may appear.
z Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire. Do not place your children's favorite toys or any other objects of interest on the product. z Children may try to climb on the product to retrieve an object. The product could fall, causing physical damage or even death. When lifting up or moving the monitor, do not lift the monitor upside down while holding only the stand.
SyncMaster 740B / 940B Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Type 1 Monitor & Simple stand Bottom MagicRotation program can not be provided as Simple Stand does not support Pivot function.
Monitor & Sliding Stand Type 4 Monitor & Lowest HAS Stand Manual Quick Setup Guide Warranty Card (Not available in all locations) User's Guide, Monitor Driver, Natural Color software, MagicTune™ software MagicRotation software D-sub Cable Power Cord DVI Cable (option) Cable Front
MENU button [ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. MagicBright™™ [ ] MagicBright™™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently six different modes are available: Custom, Text, Internet, Game, Sport and Movie. Each mode has its own pre-configured brightness value. You can easily select one of six settings by simply pressing MagicBright™ control button.
AUTO button Use this button for auto adjustment. Power button [ ]/ Power indicator Use this button for turn the monitor on and off. / This light glows blue during normal operation, and blinking blue once as the monitor saves your adjustments. See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
SyncMaster 540B Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Type 1 Monitor & Simple stand Bottom MagicRotation program can not be provided as Simple Stand does not support Pivot function.
Quick Setup Guide Warranty Card (Not available in all locations) User's Guide, Monitor Driver, Natural Color software, MagicTune™ software MagicRotation software D-sub Cable Power Cord DVI Cable (option) Cable Front MENU button [ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. MagicBright™™ [ ] MagicBright™™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching.
the pre-configured values may not be comfortable for your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu. 2) Text For documentations or work involving a lot of text. 3) Internet For working with a mixture of images such as text and graphics. 4) Game For watching motion pictures such as a game. 5) Sport For watching motion pictures such as a sport. 6) Movie For watching motion pictures such as a DVD or Video CD.
Simple stand Pivot stand (The configuration at the back of the monitor may vary from product to product.) POWER port DVI IN port RGB IN port Kensington Lock Connect the power cord for your monitor to the power port on the back of the monitor. Connect the DVI Cable to the DVI port on the back of your monitor. Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. The Kensington lock is a device used to physically fix the system to something when using it in a public place.
SyncMaster 740N / 940N Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Type 1 Monitor & Simple stand Bottom MagicRotation program can not be provided as Simple Stand does not support Pivot function.
Monitor & Sliding Stand Type 4 Monitor & Lowest HAS Stand Manual Quick Setup Guide Warranty Card (Not available in all locations) D-sub Cable Power Cord Cable Front User's Guide, Monitor Driver, Natural Color software, MagicTune™ software MagicRotation software
MENU button [ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. MagicBright™™ [ ] MagicBright™™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently six different modes are available: Custom, Text, Internet, Game, Sport and Movie. Each mode has its own pre-configured brightness value. You can easily select one of six settings by simply pressing MagicBright™ control button.
See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. Rear Simple stand Pivot stand / Sliding Stand (The configuration at the back of the monitor may vary from product to product.) Connect the power cord for your monitor to the power port on the back of the monitor.
SyncMaster 540N Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Type 1 Monitor & Simple stand Bottom MagicRotation program can not be provided as Simple Stand does not support Pivot function.
Quick Setup Guide Warranty Card (Not available in all locations) D-sub Cable Power Cord User's Guide, Monitor Driver, Natural Color software, MagicTune™ software MagicRotation software Cable Front MENU button [ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. MagicBright™™ [ ] MagicBright™™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching.
the pre-configured values may not be comfortable for your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu. 2) Text For documentations or work involving a lot of text. 3) Internet For working with a mixture of images such as text and graphics. 4) Game For watching motion pictures such as a game. 5) Sport For watching motion pictures such as a sport. 6) Movie For watching motion pictures such as a DVD or Video CD.
RGB IN port Kensington Lock of the monitor. Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. The Kensington lock is a device used to physically fix the system to something when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact the place of purchase. See Connecting the Monitor for further information regarding cable connections.
SyncMaster 940Fn Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.
Front MENU button [ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. MagicBright™™ [ ] MagicBright™™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently six different modes are available: Custom, Text, Internet, Game, Sport and Movie. Each mode has its own pre-configured brightness value. You can easily select one of six settings by simply pressing MagicBright™ control button.
Enter button [ ] / Source button Activates a highlighted menu item. / Push the ' ', then selects the video signal while the OSD is off. (When the source button is pressed to change the input mode, a message appears in the upper left of the screen displaying the current mode -- analog or digital input signal.) Note : If you select the digital mode, you must connect your monitor to the graphic card's DVI port using the DVI cable. AUTO button Use this button for auto adjustment.
SyncMaster 740T / 940T Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Type 1 Monitor & Simple stand Bottom MagicRotation program can not be provided as Simple Stand does not support Pivot function.
Monitor & Lowest HAS Stand Manual Quick Setup Guide Warranty Card (Not available in all locations) User's Guide, Monitor Driver, Natural Color software, MagicTune™ software MagicRotation software D-sub Cable Power Cord DVI Cable (option) Cable Front
MENU button [ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. MagicBright™™ [ ] MagicBright™™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently six different modes are available: Custom, Text, Internet, Game, Sport and Movie. Each mode has its own pre-configured brightness value. You can easily select one of six settings by simply pressing MagicBright™ control button.
AUTO button Use this button for auto adjustment. Power button [ ]/ Power indicator Use this button for turn the monitor on and off. / This light glows blue during normal operation, and blinking blue once as the monitor saves your adjustments. See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
SyncMaster 940Be Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Type 1 Monitor & Simple stand Bottom MagicRotation program can not be provided as Simple Stand does not support Pivot function.
Quick Setup Guide Warranty Card (Not available in all locations) User's Guide, Monitor Driver, Natural Color software, MagicTune™ software MagicRotation software D-sub Cable Power Cord DVI Cable (option) Cable Front MENU button [ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. MagicBright™™ [ ] MagicBright™™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching.
the pre-configured values may not be comfortable for your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu. 2) Text For documentations or work involving a lot of text. 3) Internet For working with a mixture of images such as text and graphics. 4) Game For watching motion pictures such as a game. 5) Sport For watching motion pictures such as a sport. 6) Movie For watching motion pictures such as a DVD or Video CD.
Simple stand Sliding Stand (The configuration at the back of the monitor may vary from product to product.) Connect the power cord for your monitor to the power port on the back of the monitor. Connect the DVI Cable to the DVI port on the back of your monitor. DVI IN port Connect the signal cable to the 15-pin, D-sub port on the back of your RGB IN port monitor. POWER on/off Switch Use this button for turn the monitor on and off.
SyncMaster 740B / 940B / 540B / 740T / 940T / 940Be Connecting the Monitor 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. [ RGB IN ] 2-2. Using the DVI (Digital) connector on the video card. Connect the DVI Cable to the DVI Port on the back of your Monitor.
Using the Stand Monitor Assembly Monitor and Bottom Pivot Stand / Sliding Stand A.Stand Stopper Attaching a Base This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad.
Simple stand Pivot stand Sliding Stand Lowest HAS Stand A. Monitor B. Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4.
SyncMaster 740N Connecting the Monitor 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. [ RGB IN ] 2-2. Connected to a Macintosh. Connect the monitor to the Macintosh computer using the D-sub connection cable. 2-3.
Monitor Assembly Monitor and Bottom Swivel stand Pivot Stand / Sliding Stand
A.Stand Stopper Attaching a Base This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad. Simple stand Pivot stand Sliding Stand Lowest HAS Stand A. Monitor B. Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4.
SyncMaster 940Fn Connecting the Monitor 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analog) connector on the video card. Connect the 'DVI-A to D-SUB' Cable to the RGB IN port on the back of your monitor. [ RGB IN ] 2-2. Using the DVI (Digital) connector on the video card. Connect the DVI Cable to the DVI IN port on the back of your monitor. [ DVI IN ] 2-3.
Using the Stand Pivot Stand A.Stand Stopper Attaching a Base This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad. A. Monitor B. Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4.
SyncMaster 540N / 940N Connecting the Monitor 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. [ RGB IN ] 2-2. Connected to a Macintosh. Connect the monitor to the Macintosh computer using the D-sub connection cable. 2-3.
Monitor Assembly Monitor and Bottom Pivot Stand A.Stand Stopper Attaching a Base This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad.
Simple stand A. Monitor Pivot stand B. Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4. Align the mounting interface pad with the holes in the rear cover mounting Pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.
4. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. (Microsoft® Windows® XP Operating System) This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/. 5. Monitor driver installation is completed.
3. Click "Display" icon and choose the "Settings" tab then click "Advanced..". 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk".
7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certified MS logo,and this installation doesn't damage your system.The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 9. Click the "Close" button then click "OK" button continually.
10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Click "Start" , "Setting" , "Control Panel". Double click the "Display" Icon.
not normal, change to a different mode (lower mode of resolution, colors or frequency). If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Timing Modes in the user guide. Linux Operating System To execute X-Window, you need to make the X86Config file, which is a type of system setting file. 1. 2. 3. 4. 5. 6. 7. Press Enter at the first and the second screen after executing the X86Config file.
ROM Drive, click the Windows [Start] button, select [Run...]. Enter D:\color\NCProsetup.exe and then press the key. (If the drive where the CD is inserted is not D:\, enter the applicable drive.) Uninstalling the Natural Color Software Program Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a program". Select Natural Color from the list and then click the "Add/Delete" button.
SyncMaster 740B / 940B 1. [ ]Opens the on-screen menu and exits from the menu or closes the adjustment menu. 2. [ ]This button allows you to adjust items in the menu. 3. [ ]Press this button to Activates a highlighted menu item. 4. [AUTO]Press to Self-Adjusts the incoming PC signal automatically. The values of fine,coarse and position are adjusted automatically.
Menu Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. (Available in analog mode only) AUTO To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.
Menu Locked Description After pushing the "MENU" button more than 5 seconds, OSD function is locked (unlocked). You can also adjust the brightness and contrast of the monitor with the OSD adjustment locking feature. MagicBright™ Menu MagicBright™ Description Push the MagicBright button to circle through available preconfigured modes.
Brightness Menu Brightness Description When OSD is not on the screen, push the button to adjust brightness. SOURCE Menu SOURCE Description Selects the video signal while the OSD is off.
Picture Brightness Contrast Color MagicColor Color Tone Color Control Gamma Image Coarse Fine Sharpness H-Position V-Position OSD Language H-Position V-Position Transparency Display Time Setup Auto Source Image Reset Color Reset Information Picture Menu Description You can use the on-screen menus to change the brightness according to personal preference. Brightness Direct Access Feature : When OSD is not on the screen, push the button to adjust brightness.
Menu Description Play/Stop MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality. 1) Off - Returns to the original mode. 2) Demo - The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left. 3) Full - Displays not only vivid natural color but also more realistic natural skin color with clearness.
: This function is to adjust the vertical size of the MagicZone. Color Tone The tone of the color can be changed and one of four modes can be selected - Cool, Normal, Warm and Custom. (Not available in MagicColor mode of Full and Intelligent.) Color Control Adjusts individual R,G,B color balance. (Not available in MagicColor mode of Full and Intelligent.) Gamma correction changes the luminance of the colors with intermediate luminance.
V-Position display. (Available in analog mode only) OSD Menu Description You can choose one of 9 languages. Language Note:The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. H-Position You can change the horizontal position where the OSD menu appears on your monitor. V-Position You can change the vertical position where the OSD menu appears on your monitor. Transparency Change the transparency of the background of the OSD.
Menu Description Auto Source Select Auto Source for the monitor to automatically select the signal source. Image Reset Image parameters are replaced with the factory default values. Color Reset Color parameters are replaced with the factory default values.
Menu Information Description Shows a video source, display mode on the OSD screen.
SyncMaster 740N / 940N 1. [ ]Opens the on-screen menu and exits from the menu or closes the adjustment menu. 2. [ ]This button allows you to adjust items in the menu. 3. [ ]Press this button to Activates a highlighted menu item. 4. [AUTO]Press to Self-Adjusts the incoming PC signal automatically. The values of fine,coarse and position are adjusted automatically.
Menu Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. (Available in analog mode only) AUTO To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.
Menu Locked Description After pushing the "MENU" button more than 5 seconds, OSD function is locked (unlocked). You can also adjust the brightness and contrast of the monitor with the OSD adjustment locking feature. MagicBright™ Menu MagicBright™ Description Push the MagicBright button to circle through available preconfigured modes.
Brightness Menu Description When OSD is not on the screen, push the button to adjust brightness.
Menu Description You can use the on-screen menus to change the brightness according to personal preference. Brightness Direct Access Feature : When OSD is not on the screen, push the button to adjust brightness. Contrast Color You can use the on-screen menus to change the contrast according to personal preference. (Not available in MagicColor mode of Full and Intelligent.
Menu Description Play/Stop MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality. 1) Off - Returns to the original mode. 2) Demo - The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left. 3) Full - Displays not only vivid natural color but also more realistic natural skin color with clearness.
Menu Description Coarse Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. (Available in analog mode only) Fine Removes noise such as horizontal stripes. If the noise persists even after fine tuning, repeat it after adjusting the frequency (clock speed). (Available in analog mode only) Sharpness Changes the clearance of image. (Not available in MagicColor mode of Full and Intelligent.
Menu Description You can choose one of 9 languages. Language Note:The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. H-Position You can change the horizontal position where the OSD menu appears on your monitor. V-Position You can change the vertical position where the OSD menu appears on your monitor. Transparency Change the transparency of the background of the OSD.
Menu Description Image Reset Image parameters are replaced with the factory default values. Color Reset Color parameters are replaced with the factory default values. Information Menu Information Description Shows a video source, display mode on the OSD screen.
SyncMaster 940Fn 1. [ ]Opens the on-screen menu and exits from the menu or closes the adjustment menu. 2. [ ]This button allows you to adjust items in the menu. 3. [ ]Press this button to Activates a highlighted menu item. 4. [AUTO]Press to Self-Adjusts the incoming PC signal automatically. The values of fine,coarse and position are adjusted automatically.
Menu Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. (Available in analog mode only) AUTO To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.
Menu Locked Description After pushing the "MENU" button more than 5 seconds, OSD function is locked (unlocked). You can also adjust the brightness and contrast of the monitor with the OSD adjustment locking feature. MagicBright™ Menu MagicBright™ Description Push the MagicBright button to circle through available preconfigured modes.
Brightness Menu Brightness Description When OSD is not on the screen, push the button to adjust brightness. SOURCE Menu SOURCE Description Selects the video signal while the OSD is off.
Picture Brightness Contrast Color MagicColor Color Tone Color Control Gamma Image Coarse Fine Sharpness H-Position V-Position OSD Language H-Position V-Position Transparency Display Time Setup Auto Source Image Reset Color Reset Priority Information Picture Menu Description You can use the on-screen menus to change the brightness according to personal preference. Brightness Direct Access Feature : When OSD is not on the screen, push the button to adjust brightness.
Menu Description Play/Stop MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality. 1) Off - Returns to the original mode. 2) Demo - The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left. 3) Full - Displays not only vivid natural color but also more realistic natural skin color with clearness.
: This function is to adjust the vertical size of the MagicZone. Color Tone The tone of the color can be changed and one of four modes can be selected - Cool, Normal, Warm and Custom. (Not available in MagicColor mode of Full and Intelligent.) Color Control Adjusts individual R,G,B color balance. (Not available in MagicColor mode of Full and Intelligent.) Gamma correction changes the luminance of the colors with intermediate luminance.
V-Position display. (Available in analog mode only) OSD Menu Description You can choose one of eight languages. Language Note:The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. H-Position You can change the horizontal position where the OSD menu appears on your monitor. V-Position You can change the vertical position where the OSD menu appears on your monitor. Transparency Change the transparency of the background of the OSD.
Menu Description Auto Source Select Auto Source for the monitor to automatically select the signal source. Image Reset Image parameters are replaced with the factory default values. Color Reset Color parameters are replaced with the factory default values. Priority This is a source-switch function according to the priority that the user has set for the source.
Menu Information Description Shows a video source, display mode on the OSD screen.
SyncMaster 540B / 740T / 940T / 940Be 1. [ ]Opens the on-screen menu and exits from the menu or closes the adjustment menu. 2. [ ]This button allows you to adjust items in the menu. 3. [ ]Press this button to Activates a highlighted menu item. 4. [AUTO]Press to Self-Adjusts the incoming PC signal automatically. The values of fine,coarse and position are adjusted automatically.
Menu Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. (Available in analog mode only) AUTO To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.
Menu Locked Description After pushing the "MENU" button more than 5 seconds, OSD function is locked (unlocked). You can also adjust the brightness and contrast of the monitor with the OSD adjustment locking feature. MagicBright™ Menu MagicBright™ Description Push the MagicBright button to circle through available preconfigured modes.
Brightness Menu Brightness Description When OSD is not on the screen, push the button to adjust brightness. SOURCE Menu SOURCE Description Selects the video signal while the OSD is off.
Picture Brightness Contrast Color MagicColor Color Tone Color Control Gamma Image Coarse Fine Sharpness H-Position V-Position OSD Language H-Position V-Position Transparency Display Time Setup Auto Source Image Reset Color Reset Information Picture Menu Description You can use the on-screen menus to change the brightness according to personal preference. Brightness Direct Access Feature : When OSD is not on the screen, push the button to adjust brightness.
Menu Description Play/Stop MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality. 1) Off - Returns to the original mode. 2) Demo - The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left. 3) Full - Displays not only vivid natural color but also more realistic natural skin color with clearness.
: This function is to adjust the vertical size of the MagicZone. Color Tone The tone of the color can be changed and one of four modes can be selected - Cool, Normal, Warm and Custom. (Not available in MagicColor mode of Full and Intelligent.) Color Control Adjusts individual R,G,B color balance. (Not available in MagicColor mode of Full and Intelligent.) Gamma correction changes the luminance of the colors with intermediate luminance.
V-Position display. (Available in analog mode only) OSD Menu Description You can choose one of eight languages. Language Note:The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. H-Position You can change the horizontal position where the OSD menu appears on your monitor. V-Position You can change the vertical position where the OSD menu appears on your monitor. Transparency Change the transparency of the background of the OSD.
Menu Description Auto Source Select Auto Source for the monitor to automatically select the signal source. Image Reset Image parameters are replaced with the factory default values. Color Reset Color parameters are replaced with the factory default values.
Menu Information Description Shows a video source, display mode on the OSD screen.
SyncMaster 540N 1. [ ]Opens the on-screen menu and exits from the menu or closes the adjustment menu. 2. [ ]This button allows you to adjust items in the menu. 3. [ ]Press this button to Activates a highlighted menu item. 4. [AUTO]Press to Self-Adjusts the incoming PC signal automatically. The values of fine,coarse and position are adjusted automatically.
Menu Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. (Available in analog mode only) AUTO To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.
Menu Locked Description After pushing the "MENU" button more than 5 seconds, OSD function is locked (unlocked). You can also adjust the brightness and contrast of the monitor with the OSD adjustment locking feature. MagicBright™ Menu MagicBright™ Description Push the MagicBright button to circle through available preconfigured modes.
Brightness Menu Description When OSD is not on the screen, push the button to adjust brightness.
Menu Description You can use the on-screen menus to change the brightness according to personal preference. Brightness Direct Access Feature : When OSD is not on the screen, push the button to adjust brightness. Contrast Color You can use the on-screen menus to change the contrast according to personal preference. (Not available in MagicColor mode of Full and Intelligent.
Menu Description Play/Stop MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality. 1) Off - Returns to the original mode. 2) Demo - The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left. 3) Full - Displays not only vivid natural color but also more realistic natural skin color with clearness.
Menu Description Coarse Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. (Available in analog mode only) Fine Removes noise such as horizontal stripes. If the noise persists even after fine tuning, repeat it after adjusting the frequency (clock speed). (Available in analog mode only) Sharpness Changes the clearance of image. (Not available in MagicColor mode of Full and Intelligent.
Menu Description You can choose one of 8 languages. Language Note:The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. H-Position You can change the horizontal position where the OSD menu appears on your monitor. V-Position You can change the vertical position where the OSD menu appears on your monitor. Transparency Change the transparency of the background of the OSD.
Menu Description Image Reset Image parameters are replaced with the factory default values. Color Reset Color parameters are replaced with the factory default values. Information Menu Information Description Shows a video source, display mode on the OSD screen.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Overview What is MagicTune™ ? Monitor performance can vary due to the graphics card, host computer lighting conditions and other environmental factors. In order to get the best image on a monitor requires you to adjust it for your unique setting. Unfortunately, the manual controls available to tune the image often prove to be challenging.
The OSD mode allows easy adjustment of monitor settings without taking pre-defined steps. You can access the desired menu item to set with ease.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Installation 1. Insert the installation CD into the CD-ROM drive. 2. Click the MagicTune™ installation file. 3. Select installation Language, Click "Next". 4. When the Installation Shield Wizard window appears, click "Next." 5. Select "I agree to the terms of the license agreement" to accept the terms of use. 6. Choose a folder to install the MagicTune™ program. 7. Click "Install." 8.
z z z Windows™ 2000 Windows™ XP Home Edition Windows™ XP Professional It is recommended using MagicTune™ in Windows™ 2000 or later. Hardware z z 32 MB Memory above 60 MB Hard disk space above * For more information, visit the MagicTune™ website.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting MagicTune™ allows for quick accurate tuning of the display with the ability to easily save and use monitor configurations that are best suited for you. z z z OSD mode may appear inconsistent with the explanation in guidance book depending on specification of each monitor. When Pivot is functioning, part of MagicTune™ Program may not operate normally.
Picture Tab Definition Allows the user to adjust the screen settings to the desired values. Brightness Makes the entire screen brighter or darker. The detailed data of the images in the dark areas can be lost if the brightness is not adjusted to the proper level. Adjust the brightness for best viewing conditions. Contrast Adjusts the difference in brightness between the bright and dark areas on screen. Determines the crispness of the images.
MagicColor and Gamma will be shown only in the monitor that supports these functions. The tone of the color can be changed. z z Warm2 - Warm1 - Cool 1 - Cool 2 - Cool 3 - Cool 4 - Cool 5 - Cool 6 - Cool 7 Off ColorTone ColorTone mode will be different according to monitor models. Some monitor will only support Four modes( Warm, Normal, Cool, Custom) Color Control Adjusts of the monitor image color. You can change the monitor color to your desired color.
{ players also can be highlighted but could have some problems. Tusk menu HUE Adjust the tint of the color. Saturation Adjusts the color saturation. Brightness Adjusts the Brightness. Sharpness Adjusts the difference between the lightest and darkest areas of the display. Zone Off Turn off the zone that you have captured. Reset Returns to the the default setting that vendor has set.
Hue - To adjust the color tone. Reset - To reset the monitor settings to the factory defaults. z z Image Tab Definition Adjusts the Fine , Coarse and Position values. z Image Setup z z Fine : Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). Coarse : Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the Horizontal Control menu.
z z Custom - Partial Color Blindness Test Reset - To reset the monitor settings to the factory defaults. When external A/V devices such as VCRs or DVDs are connected to the monitor, PIP allows you to watch video from those devices in a small window super-imposed on the PC Video signal. (Off / On) PIP Turn the PIP Screen on or off. Source Select the input source for the PIP. Size Change the Size of the PIP window. PIP Position Change the Position of the PIP window.
you can use the server to control the Client monitor. (Server program should be installed to use this program as Client) When selecting the Customize checkbox at the bottom you can enter your personal information. Asset ID Version User Name Shows the user name that is registered in PC. User ID Shows the user ID that is register in PC. Server IP Write down the server IP . Department Write down the department. Location Write down the location. Displays the version of MagicTune™ .
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Color Calibration 1. Color Calibration Color Calibration guides you to get optimal color condition for your monitor. Proceed following 5steps for getting optimal monitor color condition . 1. 2. 3. 4. 5.
The above picture will be shown. 1. 2. Press "View Calibrated" button to see the calibration effect which you adjusted. Press "View Uncalibrated" button to see the original image.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Uninstall The MagicTune™ program can be removed only by using the "Add or Remove Programs" option of the Windows™ Control Panel. Perform the following steps remove MagicTune™ . 1. 2. 3. 4. 5. 6. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on Windows™ XP, go to [Control Panel] in the [Start] menu. Click the "Add or Remove Programs" icon in Control Panel.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Troubleshooting The current computing system is not compatible with MagicTune™ . Please press OK and click on the "Shortcut to the MagicTune™ site" to view our home page for further reference. An error may occur when your video/graphic card is not in the 'Available' list. (The latest or oldest video cards may not be compatible.) Please visit our homepage to see the Troubleshooting section.
Hardware > Device Manager > Monitor is selected, the current "Plug-and-play monitor" is removed and new hardware is searched for but the system couldn't find any "Plug-and-play monitor". Please visit our homepage to see the Troubleshooting section. An error occurs when replacing the monitor with a new one when the system power is off but the system has not been restarted. Please restart the system each time the monitor is replaced before using MagicTune™ .
Adapter. Visit the video card manufacturer's homepage and download and install the latest driver. For more information about the video card, contact the card manufacturer. As the Highlight program uses the communication lines, please exit the Highlight program before you can access MagicTune™ . Some of Samsung CDT monitors support the Highlight feature. When using both the Highlight feature and MagicTune™ simultaneously, conflicts occur, which cause errors.
program is already installed, remove it, reboot the computer, and then install the program again. You need to reboot the computer for it to operate normally after installing or removing the program. z z Visit the MagicTune™ website for technical support for MagicTune™ , FAQs (questions and answers) and software upgrades. Visit the MagicTune™ website and download the installation software for MagicTune™ MAC.
Overview | Installation | Interface | Uninstall | Troubleshooting Overview What is MagicRotation? Traditionally, computer displays allowed the user to view only in landscape mode. In today's information age, more users need to view documents, web pages, emails, etc. in there day to day life. These types of applications can be better viewed in portrait mode where the entire contents are available on the screen.
Overview | Installation | Interface | Uninstall | Troubleshooting Installation 1. Insert the installation CD into the CD-ROM drive. 2. Click the MagicRotation installation file. 3. Select installation Language, Click "Next". 4. When the InstallShield Wizard window appears, click "Next." 5. Select "I accept the terms of the license agreement" to accept the terms of use.
6. Choose a folder to install the MagicRotation program. 7. Click "Install." 8. The "Setup Status" window appears.
9. Click "Finish." Have to reboot the system in order for the MagicRotation to work properly. 10. When the installation is complete, the MagicRotation executable icon appears on your desktop. Installation Problems The installation of MagicRotation can be affected by the factors such as video card, motherboard and the network environment. See "Troubleshooting" if you have trouble during installation. Limitation 1. The "Display Driver" should be properly loaded for the MagicRotation to work properly.
movie files properly in 90, 180 and 270 orientations then do the following : { Close the application. { Select the Orientation (90, 180, 270) you want to view the application. { Relaunch the application. In most cases this should fix the problem. 3. User Applications using OpenGL and DirectDraw (3D drawing) will not function as per the orientation mode selected (90, 180, 270). e.g. 3D games 4. DOS based applications in Full Screen Mode will not function as per the orientation mode selected (90, 180, 270).
Overview z z | Installation | Interface | Uninstall | Troubleshooting When Rotation is functioning, portion of MagicTune™ program may not operate normally. AutoRotation : The screens display will automatically rotate when the monitor is rotated. z z z z z To execute Auto Rotation, it should be done as below. Please install both MagicRotation and MagicTune™ 3.6 programs in your computer. Launch MagicTune 3.6 Option ¡ Preference ¡ Click the small box in the enable task tray menu.
Rotate to 90 : Display will be rotated 90 degrees from the current angle. Rotate to 180 : Display will be rotated 180 degrees from the current angle.
Rotate to 270 : Display will be rotated 270 degrees from the current angle. Hot key : Hot Keys are available by default and can be changed by user. It can be assigned by user directly with keyboard after changing the existing HotKey . User can create the hot key with the combination of Shift, Ctrl, Alt and general keys. In case only general key is pressed, it will be assigned in the form of Alt+general key. Help : Shows the HELP of MagicRotation program.
Overview | Installation | Interface | Uninstall | Troubleshooting Uninstall The MagicRotation program can be removed only by using the "Add/Remove Programs" option of the Windows Control Panel. Perform the following steps to remove MagicRotation. 1. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on Windows™ XP, go to [Control Panel] in the [Start] menu. 2. Click the "Add/Remove Programs" icon in Control Panel. 3.
Overview | Installation | Interface | Uninstall | Troubleshooting Troubleshooting Before You Call Technical Support z MagicRotation Software works with the installed "Display Driver" supplied by your Graphic Card Vendor to provide screen rotation capabilities. If the installed "Display Driver" is working incorrectly or has bugs in it, then these bugs would still exist even after MagicRotation Software is installed.
SyncMaster 740B / 940B / 540B / 740T / 940T / 940Be Check List Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom No images on the screen. I cannot turn on the monitor. Check List Solutions Is the power cord connected properly? Check the power cord connection and supply.
Mode","Recommended mode 1280 x 1024 60 Hz" message is displayed. If the display exceeds 85 Hz, the display will work properly but the "Not Optimum Mode","Recommended Mode 1280 x 1024 60 Hz" message appears for one minute and then disappears. Please change to the recommended mode during this one-minute period. (The message is displayed again if the system is rebooted.) There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? The monitor is in PowerSaver mode.
resolution may differ from product to product.) There are only 16 colors shown on the screen. The screen colors have changed after changing the video card. Have the Windows colors been set properly? Windows ME/2000/XP: Set the colors properly at the Control Panel ¡ Display ¡ Settings. Has the video card been set properly? Set the video card by referring to the video card manual. There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found".
Q&A Question How can I change the frequency? Answer The frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) How can I adjust the resolution? Windows ME/XP/2000 : Set the resolution at the Control Panel¡ Display¡ Settings. * Contact the video card manufacturer for details.
Environment The location and the position of the monitor may influence the quality and other features of the monitor. 1. if there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room. 2. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor. Useful Tips z A monitor recreates visual signals received from the computer.
SyncMaster 740N / 540N / 940N Check List Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom No images on the screen. I cannot turn on the monitor. Check List Solutions Is the power cord connected properly? Check the power cord connection and supply.
disappears. Please change to the recommended mode during this one-minute period. (The message is displayed again if the system is rebooted.) The screen shows strange colors or just black and white. There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? The monitor is in PowerSaver mode. Is the screen displaying only one color as if looking at the screen through a cellophane paper? Check the signal cable connection.
Control Panel -> Performance and Maintenance -> System -> Hardware -> Device Manager -> Monitors -> After deleting Plug and Play monitor, find 'Plug and Play monitor' by searching new Hardware. MagicTune™ is an additional software for the monitor. Some graphic cards may not support your monitor. When you have a problem with the graphic card, visit our website to check the compatible graphic card list provided. http://www.samsung.com/monitor/magictune MagicTune™ doesn't work properly.
Self-Test Feature Check Self-Test Feature Check | Warning Messages | Environment | Useful Tips Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Self-Test Feature Check 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor. If the monitor is functioning properly, you will see a box in the illustration below.
1024 60 Hz" message comes up, disconnect the cable from the computer while the monitor is still powered on. { If there is a message coming up on the screen or if the screen goes white, this means the monitor is in working condition. { In this case, check the computer for trouble.
SyncMaster 940Fn Check List Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom No images on the screen. I cannot turn on the monitor. Check List Solutions Is the power cord connected properly? Check the power cord connection and supply.
Hz, a "Not Optimum Mode","Recommended Mode 1280 x 1024 60 Hz" message is displayed. If the display exceeds 85 Hz, the display will work properly but the "Not Optimum Mode","Recommended Mode 1280 x 1024 60 Hz" message appears for one minute and then disappears. Please change to the recommended mode during this one-minute period. (The message is displayed again if the system is rebooted.) There is no image on the screen.
(The maximum frequency per resolution may differ from product to product.) There are only 16 colors shown on the screen. The screen colors have changed after changing the video card. Have the Windows colors been set properly? Windows ME/2000/XP: Set the colors properly at the Control Panel ¡ Display ¡ Settings. Has the video card been set properly? Set the video card by referring to the video card manual. There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found".
Q&A Question How can I change the frequency? Answer The frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) How can I adjust the resolution? Windows ME/XP/2000 : Set the resolution at the Control Panel¡ Display¡ Settings. * Contact the video card manufacturer for details.
Environment The location and the position of the monitor may influence the quality and other features of the monitor. 1. if there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room. 2. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor. Useful Tips z A monitor recreates visual signals received from the computer.
General General Model Name SyncMaster 740B LCD Panel Size 17 " Diagonal (43 cm) Display area 337.92 mm (H) x 270.336 mm (V) Pixel Pitch 0.264 mm (H) x 0.264 mm (V) Synchronization Horizontal 30 ~ 81 k Hz Vertical 56 ~ 75 Hz Display Color 16.2 M Colors Resolution Optimum resolution 1280 x 1024@60 Hz Maximum resolution 1280 x 1024@75 Hz Input Signal, Terminated RGB Analog , DVI(Digital Visual Interface) Compliant Digital RGB 0.
Dimensions (WxHxD)/ Weight (Pivot Stand) 366.0 x 391.2 x 200.0 mm / 14.4 x 15.4 x 7.9 inch (with Basic Stand) / 4.7 kg Dimensions (WxHxD)/ Weight (Sliding Stand) 366.0 x 391.2 x 200.0 mm / 14.4 x 15.4 x 7.9 inch (with Basic Stand) / 4.7 kg Dimensions (WxHxD)/ Weight (Lowest HAS Stand) 366.0 x 351.4 x 200.0 mm / 14.4 x 13.8 x 7.9 inch (with Basic Stand) / 4.8 kg VESA Mounting Interface 75 mm x 75 mm (for use with Specialty(Arm) Mounting hardware.
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPMS functionality. As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on.
many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate.
General General Model Name SyncMaster 940B LCD Panel Size 19 " Diagonal (48 cm) Display area 376.32 mm (H) x 301.056 mm (V) Pixel Pitch 0.294 mm (H) x 0.294 mm (V) Synchronization Horizontal 30 ~ 81 k Hz Vertical 56 ~ 75 Hz Display Color 16.7 M Colors Resolution Optimum resolution 1280 x 1024@60 Hz Maximum resolution 1280 x 1024@75 Hz Input Signal, Terminated RGB Analog , DVI(Digital Visual Interface) Compliant Digital RGB 0.
Dimensions (WxHxD)/ Weight (Pivot Stand) 407.6 x 408.0 x 200.0mm / 16.0 x 16.1 x 7.9 inch (with Basic Stand) / 5.55 kg Dimensions (WxHxD)/ Weight (Sliding Stand) 407.6 x 408.0 x 200.0mm / 16.0 x 16.1 x 7.9 inch (with Basic Stand) / 5.7 kg Dimensions (WxHxD)/ Weight (Lowest HAS Stand) 407.6 x 368.2 x 200.0 mm / 16.0 x 14.5 x 7.9 inch (with Basic Stand) / 5.8 kg VESA Mounting Interface 75 mm x 75 mm (for use with Specialty(Arm) Mounting hardware.
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPMS functionality. As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on.
many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate.
General General Model Name SyncMaster 740N LCD Panel Size 17 " Diagonal (43 cm) Display area 337.92 mm (H) x 270.336 mm (V) Pixel Pitch 0.264 mm (H) x 0.264 mm (V) Synchronization Horizontal 30 ~ 81 k Hz Vertical 56 ~ 75 Hz Display Color 16.2 M Colors Resolution Optimum resolution 1280 x 1024@60 Hz Maximum resolution 1280 x 1024@75 Hz Input Signal, Terminated RGB Analog 0.7Vp-p Positive at 75ȍ ±10% Separate H/V sync, Composite sync, TTL level positive or negative.
366.0 x 391.2 x 200.0 mm / 14.4 x 15.4 x 7.9 inch (with Basic Stand) / 4.7 kg Dimensions (WxHxD)/ Weight (Sliding Stand) 366.0 x 391.2 x 200.0 mm / 14.4 x 15.4 x 7.9 inch (with Basic Stand) / 4.7 kg Dimensions (WxHxD)/ Weight (Lowest HAS Stand) 366.0 x 351.4 x 200.0 mm / 14.4 x 13.8 x 7.9 inch (with Basic Stand) / 4.8 kg VESA Mounting Interface 75 mm x 75 mm (for use with Specialty(Arm) Mounting hardware.
functionality. As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1.
many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate.
General General Model Name SyncMaster 940Fn LCD Panel Size 19 " Diagonal (48 cm) Display area 376.32 mm (H) x 301.056 mm (V) Pixel Pitch 0.294 mm (H) x 0.294 mm (V) Synchronization Horizontal 30 ~ 81 k Hz Vertical 56 ~ 75 Hz Display Color 16.7 M Colors Resolution Optimum resolution 1280 x 1024@60 Hz Maximum resolution 1280 x 1024@75 Hz Input Signal, Terminated RGB Analog , DVI(Digital Visual Interface) Compliant Digital RGB 0.
VESA Mounting Interface 75 mm x 75 mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Temperature: 50 °F ~ 104 °F (10 °C ~ 40 °C) Humidity: 10% ~ 80%, non-condensing Storage Temperature: -4 °F ~113 °F (-20 °C ~ 45 °C) Humidity: 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings.
Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.175 -/- IBM, 720 x 400 31.469 70.087 28.322 -/+ MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.726 74.551 57.284 -/- MAC, 1152 x 870 68.681 75.062 100.00 -/- VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 640 x 480 37.861 72.809 31.500 -/- VESA, 800 x 600 35.
General General Model Name SyncMaster 540B LCD Panel Size 15 " Diagonal (38 cm) Display area 304.1 mm (H) x 228.1 mm (V) Pixel Pitch 0.297 mm (H) x 0.297 mm (V) Synchronization Horizontal 30 ~ 61 k Hz Vertical 56 ~ 75 Hz Display Color 16.2 M Colors Resolution Optimum resolution 1024 x 768@60 Hz Maximum resolution 1024 x 768@75 Hz Input Signal, Terminated RGB Analog , DVI(Digital Visual Interface) Compliant Digital RGB 0.
Dimensions (WxHxD)/ Weight (Pivot Stand) 337.5 x 333.8 x 180.0mm / 13.3 x 13.1 x 7.1 inch (with Basic Stand) / 3.65 kg VESA Mounting Interface 75 mm x 75 mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Temperature: 50 °F ~ 104 °F (10 °C ~ 40 °C) Humidity: 10% ~ 80%, non-condensing Storage Temperature: -4 °F ~113 °F (-20 °C ~ 45 °C) Humidity: 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system.
Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.
General General Model Name SyncMaster 540N LCD Panel Size 15 " Diagonal (38 cm) Display area 304.1 mm (H) x 228.1 mm (V) Pixel Pitch 0.297 mm (H) x 0.297 mm (V) Synchronization Horizontal 30 ~ 61 k Hz Vertical 56 ~ 75 Hz Display Color 16.2 M Colors Resolution Optimum resolution 1024 x 768@60 Hz Maximum resolution 1024 x 768@75 Hz Input Signal, Terminated RGB Analog 0.7Vp-p Positive at 75ȍ ±10% Separate H/V sync, Composite sync, SOG(Option), TTL level positive or negative.
337.5 x 333.8 x 180.0mm / 13.3 x 13.1 x 7.1 inch (with Basic Stand) / 3.65 kg VESA Mounting Interface 75 mm x 75 mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Temperature: 50 °F ~ 104 °F (10 °C ~ 40 °C) Humidity: 10% ~ 80%, non-condensing Storage Temperature: -4 °F ~113 °F (-20 °C ~ 45 °C) Humidity: 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system.
Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.
General General Model Name SyncMaster 740T LCD Panel Size 17 " Diagonal (43 cm) Display area 337.92 mm (H) x 270.336 mm (V) Pixel Pitch 0.264 mm (H) x 0.264 mm (V) Synchronization Horizontal 30 ~ 81 k Hz Vertical 56 ~ 75 Hz Display Color 16.2 M Colors Resolution Optimum resolution 1280 x 1024@60 Hz Maximum resolution 1280 x 1024@75 Hz Input Signal, Terminated RGB Analog , DVI(Digital Visual Interface) Compliant Digital RGB 0.
Dimensions (WxHxD)/ Weight (Sliding Stand) 362.1 x 389.6 x 200.0 mm / 14.4 x 15.3 x 7.9 inch (with Basic Stand) / 4.5 kg Dimensions (WxHxD)/ Weight (Lowest HAS Stand) 362.1 x 349.8 x 200.0 mm / 14.4 x 13.8 x 7.9 inch (with Basic Stand) / 4.6 kg VESA Mounting Interface 75 mm x 75 mm (for use with Specialty(Arm) Mounting hardware.
product meets the ENERGY STAR® guidelines for energy efficiency. Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1.
many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate.
General General Model Name SyncMaster 940T LCD Panel Size 19 " Diagonal (48 cm) Display area 376.32 mm (H) x 301.056 mm (V) Pixel Pitch 0.294 mm (H) x 0.294 mm (V) Synchronization Horizontal 30 ~ 81 k Hz Vertical 56 ~ 75 Hz Display Color 16.7 M Colors Resolution Optimum resolution 1280 x 1024@60 Hz Maximum resolution 1280 x 1024@75 Hz Input Signal, Terminated RGB Analog , DVI(Digital Visual Interface) Compliant Digital RGB 0.
Dimensions (WxHxD)/ Weight (Sliding Stand) 403.2 x 406.4 x 200.0 mm / 16.0 x 16.0 x 7.9 inch (with Basic Stand) / 5.3 kg Dimensions (WxHxD)/ Weight (Lowest HAS Stand) 403.6 x 366.3 x 200.0 mm / 16.0 X 14.4 X 7.9 inch (with Basic Stand) / 5.4 kg VESA Mounting Interface 75 mm x 75 mm (for use with Specialty(Arm) Mounting hardware.
product meets the ENERGY STAR® guidelines for energy efficiency. Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1.
many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate.
General General Model Name SyncMaster 940N LCD Panel Size 19 " Diagonal (48 cm) Display area 376.32 mm (H) x 301.056 mm (V) Pixel Pitch 0.294 mm (H) x 0.294 mm (V) Synchronization Horizontal 30 ~ 81 k Hz Vertical 56 ~ 75 Hz Display Color 16.7M Colors Resolution Optimum resolution 1280 x 1024@60 Hz Maximum resolution 1280 x 1024@75 Hz Input Signal, Terminated RGB Analog 0.7Vp-p Positive at 75ȍ ±10% Separate H/V sync, Composite sync, SOG, TTL level positive or negative.
407.6 x 408.0 x 200.0mm / 16.0 x 16.1 x 7.9 inch (with Basic Stand) / 5.55 kg Dimensions (WxHxD)/ Weight (Sliding Stand) 407.6 x 408.0 x 200.0mm / 16.0 x 16.1 x 7.9 inch (with Basic Stand) / 5.7 kg Dimensions (WxHxD)/ Weight (Lowest HAS Stand) 407.6 x 368.2 x 200.0 mm / 16.0 x 14.5 x 7.9 inch (with Basic Stand) / 5.8 kg VESA Mounting Interface 75 mm x 75 mm (for use with Specialty(Arm) Mounting hardware.
functionality. As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1.
many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate.
General General Model Name SyncMaster 940Be LCD Panel Size 19 " Diagonal (48 cm) Display area 376.32 mm (H) x 301.056 mm (V) Pixel Pitch 0.294 mm (H) x 0.294 mm (V) Synchronization Horizontal 30 ~ 81 k Hz Vertical 56 ~ 75 Hz Display Color 16.7 M Colors Resolution Optimum resolution 1280 x 1024@60 Hz Maximum resolution 1280 x 1024@75 Hz Input Signal, Terminated RGB Analog , DVI(Digital Visual Interface) Compliant Digital RGB 0.
Dimensions (WxHxD)/ Weight (Sliding Stand) 403.2 x 406.4 x 200.0 mm / 16.0 x 16.0 x 7.9 inch (with Basic Stand) / 5.3 kg VESA Mounting Interface 75 mm x 75 mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Temperature: 50 °F ~ 104 °F (10 °C ~ 40 °C) Humidity: 10% ~ 80%, non-condensing Storage Temperature: -4 °F ~113 °F (-20 °C ~ 45 °C) Humidity: 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system.
Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.
Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG (7267864) http://www.samsung.com CANADA 1-800-SAMSUNG (7267864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG (7267864) http://www.samsung.com/mx Latin America ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 4004-0000 http://www.samsung.com/br CHILE 800-726-7864 (SAMSUNG) http://www.samsung.
BELGIUM 02 201 2418 http://www.samsung.com/be CZECH REPUBLIC 844 000 844 http://www.samsung.com/cz DENMARK 38 322 887 http://www.samsung.com/dk FINLAND 09 693 79 554 http://www.samsung.com/fi FRANCE 08 25 3260 (€ 0,15/min) http://www.samsung.com/fr GERMANY 01805 - 121213 (€ 0,14/Min) http://www.samsung.de HUNGARY 06-80-SAMSUNG (7267864) http://www.samsung.com/hu ITALIA 800 SAMSUNG (7267864) http://www.samsung.com/it LUXEMBURG 02 261 03 710 http://www.samsung.
PHILIPPINES 1800-10-SAMSUNG (7267864) http://www.samsung.com/ph SINGAPORE 1800-SAMSUNG (7267864) http://www.samsung.com/sg THAILAND 1800-29-3232, 02-689-3232 http://www.samsung.com/th TAIWAN 0800-329-999 http://www.samsung.com/tw VIETNAM 1 800 588 889 http://www.samsung.com/vn Middle East & Africa SOUTH AFRICA 0860 7267864 (SAMSUNG) http://www.samsung.com/za U.A.E 800SAMSUNG (7267864) 8000-4726 http://www.samsung.
1. Adjust computer resolution and screen injection rate (refresh rate) oncomputer as described below to enjoy the best quality of picture. You can have an uneven quality of picture in the screen if the best quality of picture is not provided in TFT-LCD. { { Resolution: 1280 x 1024 Vertical frequency (refresh rate): 60 Hz 2. TFT LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product.
MÉXICO IMPORTADO POR: SAMSUNG ELECTRONICS MÉXICO. S.A. de C.V. Vía Lopez Portillo No. 6, Col. San Fco. Chilpan Tultitlán, Estado de México, C.P. 54940 Tel: 01-55-5747-5100 / 01-800-726-7864 EXPORTADO POR: Samsung Electronics CO.,LTD.
PRODUCT INFORMATION (Image Retention Free) LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention. Warranty Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty.
Ex) The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.
