DV405* DV395* DV393* DV398* Gas and Electric Dryer user manual This manual is made with 100% recycled paper. imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service or accessory parts, please register your product at or contact www.samsung.com/register 1-800-SAMSUNG (726-7864) DV405ETPAWR_03021F-08_EN_130820.
features 1. Extra Large Capacity Ultra drying capabilities are at your fingertips! Now you can dry extra-large loads. Our ultra large 7.4 cu.ft. capacity dryer circulates more air through your clothes, drying them faster for a wrinkle-free result. 2. Smart Care (DV405* Only) Samsung’s Smart Care, an automatic error-monitoring system, detects and diagnoses problems at an early stage and provides quick and easy solutions. 3.
safety instructions Congratulations on your new Samsung Dryer. This manual contains valuable information on the installation, use, and care of your appliance. Please take the time to read this manual to take full advantage of your dryer’s many benefits and features. WARNING - Risk of Fire • • • • Clothes dryer installation must be performed by a qualified installer. Install the clothes dryer according to the manufacturer’s instructions and local codes.
safety instructions IMPORTANT SAFTY INSTRUCTION WARNING WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: 1. Read all instructions before using this appliance. 2. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode. 3.
WHAT TO DO IF YOU SMELL GAS: • • • • • • Do not try to light any appliance. Do not turn on the appliance. Do not touch any electrical switch. Do not use any phone in your building. Clear the room, building or area of all occupants. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
safety instructions The interior of the dryer and exhaust duct should be cleaned periodically by qualified service personnel. This appliance must be properly grounded. Never plug the power cord into a receptacle that is not grounded adequately and in accordance with local and national codes. See installation instructions for grounding this appliance. Do not sit on top of the dryer. Because of continuing product improvements, Samsung reserves the right to change specifications without notice.
contents 8 8 9 10 10 11 13 14 15 15 16 17 17 18 20 21 22 23 installation requirements The dryer exterior Ducting requirements Important to installer Location considerations Alcove or closet installation Exhausting Gas requirements Electrical requirements Grounding Electrical connections Replacement parts and accessories Tools Needed For Installation Installation - General procedure Final installation checklist Dryer Exhaust Tips Door Reversal Connecting the inlet hose 24 26 27 27 27 28 29 30 31 31 31 Ove
installing your dryer INSTALLATION REQUIREMENTS Hire a professional to install this dryer properly. If there is a service call performed as a result of poor setup, adjustment, and connection, it is considered the responsibility of the installer. If you install the dryer, you are responsible. Make sure you have everything necessary for proper installation. 1. A GROUNDED ELECTRICAL OUTLET is required. See Electrical Requirements. 2. A POWER CORD for electric dryers (except Canada). 3.
DUCTING REQUIREMENTS • • • • • • • • • • • • • • • • • • 01 installing your dryer • Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct. Do not use a smaller duct. Ducts larger than 4 inches (10.2 cm) in diameter can result in increased lint accumulation. Lint accumulation should be cleaned regularly. If a flexible metal duct must be used, use the type with a stiff sheet metal wall. Do not use a flexible duct with a thin foil wall.
installing your dryer If the new dryer is installed into an existing exhaust system you must make sure: • The exhaust system meets all local, state, and national codes. • That a flexible plastic duct is not used. • To Inspect and clean all lint buildup from inside the existing duct. • The duct is not kinked or crushed. • The exhaust hood damper opens and closes freely. The static pressure in any exhaust system must not exceed 0.83 inches of water column, or be less than 0.
ALCOVE OR CLOSET INSTALLATION MINIMUM CLEARANCES FOR CLOSET AND ALCOVE INSTALLATIONS: A B 1 in. (2.5 cm) 1 in. (2.5 cm) 27 in. (68.6 cm) 17 in. (43.2 cm) 27 in. (68.6 cm) 1 in. (2.5 cm) 2 in. (5 cm) 31.9 in. (81.1 cm) 01 installing your dryer Sides – 1 in / 25 mm Top – 17 in / 432 mm Rear – 5 in / 127 mm Closet Front – 2 in / 51 mm If the washer and dryer are installed together, the closet front must have at least a 72 in² (465 cm²) unobstructed air opening. 5 in. (12.7cm) A. Recessed area B.
installing your dryer With optional pedestal base or stacking kit Required Dimensions for Installation With Pedestal 51.7 in. (131.4 cm) to clear open door 39 in. (99.1 cm) 53.6 in. (136.2 cm) 341.1 in. (86.5 cm) 5 in. (12.7 cm) 27 in. (68.6 cm) 5 in. (12.7 cm) 3 in. (7.6 cm) 48 in.² * (310 cm²) 24 in.² * (155 cm²) 3 in. (7.6 cm) Closet or Door 1 in. (2.5 cm) 31.9 in. (81.1 cm) 8 in.** (20.3 cm) Required Dimensions for Installation With Stacking Kit 6 in. * (15.2 cm) 78 in. (198.1 cm) 1 in.
EXHAUSTING The dryer shall not be exhausted into a chimney, a wall, a ceiling, an attic, a crawl space, or a concealed space of a building. Exhausting the dryer to the outside will prevent large amount of lint and moisture from being blown into the room. • • • • • • All dryer must be exhausted to the outside. The required exhaust duct is 4 inches(10.2 cm ) in diameter.
installing your dryer GAS REQUIREMENTS Use only natural or LP (liquid propane) gases. THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE UNITED STATES), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA). Gas dryers are equipped with a burner vent for use with natural gas.
ELECTRICAL REQUIREMENTS The wiring diagram is located on the back of the dryer. • • • Improperly connecting the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is properly grounded. Do not modify the plug provided with your dryer – if it doesn’t fit the outlet, have a proper outlet installed by a qualified electrician.
installing your dryer ELECTRICAL CONNECTIONS Before operating or testing, follow all grounding instructions in the Grounding section. An individual branch (or separate) circuit serving only your dryer is recommended. DO NOT USE AN EXTENSION CORD. Gas models – U.S. and Canada A 120 volt, 60 Hz AC approved electrical service, with a 15-ampere fuse or circuit breaker is required. Electric models – U.S. only Most U.S. dryers require a 120/240 volt, 60 Hz AC approved electrical service.
REPLACEMENT PARTS AND ACCESSORIES If your dryer requires replacement parts or accessories, contact the dealer from whom you purchased your dryer or the SAMSUNG customer care center at 1-800-SAMSUNG (726-7864). 01 installing your dryer TOOLS NEEDED FOR INSTALLATION Gather the required tools and parts before starting the installation. Read and follow the instructions provided with any tools listed here.
installing your dryer INSTALLATION - GENERAL PROCEDURE For proper installation, we recommend that you hire a qualified installer. Read these instructions completely before you begin the installation. To install the dryer, follow these steps: 1. Move your dryer to an appropriate location for installation. Consider installing the dryer and washer sideby-side so you have easy access to both appliances. To move the dryer easily, lay two of the carton cushion-tops on the floor.
WARNING 01 installing your dryer 6. Review the Electrical Requirements section, then follow the 3 Wire system connection instructions (Step 7) or 4 Wire system instructions (Step 8) below. 7. Three Wire system instructions: A. External ground connector B. Neutral grounding wire (green/yellow) C. Center silver-colored terminal block screw D. Neutral wire (white or center wire) E. ¾” (1.9 cm) UL-listed strain relief 1. Loosen or remove the center terminal block screw. 2.
installing your dryer U.S. MODELS: Risk of Electric Shock: WARNING All U.S. models are produced for a 3-WIRE SYSTEM CONNECTION. The dryer frame is grounded to the neutral conductor at the terminal block. A 4-WIRE SYSTEM CONNECTION is required for new or remodeled construction, mobile homes, or if local codes do not permit grounding through neutral. If the 4-wire system is used, the dryer frame cannot be grounded to the neutral conductor at the terminal block.
DRYER EXHAUST TIPS Plastic or non-metal flexible duct presents a potential fire hazard. WARNING 01 installing your dryer 1. Make sure your dryer is installed properly so it exhausts air easily. 2. Use a 4” diameter rigid metal duct. Tape all joints, including at the dryer. Never use lint-trapping screws. 3. Keep ducts as straight as possible. 4. Clean all old ducts before installing your new dryer. Be sure the vent flap opens and closes freely. Inspect and clean the exhaust system annually.
installing your dryer DOOR REVERSAL 1. Unplug the power cord. 2. Remove two door hinge screws. 3. Lift the door and remove it. 8. Reinsert the screw in the other hole. 4. Remove a screw on the Frame Front 9. Reinsert the screw (Step 4) on the Frame Front 5. Remove the two screws on the opposite side of the door hinge. 10. Place the door on the other side and reattach it to the dryer. 6. Remove two screws from the holder lever. 11. Reattach the holder lever. 7. Remove a screw from the door hinge.
CONNECTING THE INLET HOSE Method1 - Using the Y Connector and Long Hose Do not overtighten. You can damage the coupling. Frame (back) 6. Attach the angled end of the long hose to the fill valve at the bottom of the dryer’s rear frame. Screw on the coupling by hand until it is tight. 7. Using pliers, tighten the hose coupling with an additional two thirds turn. Do not overtighten. You can damage the coupling.
operating Instructions, tips WARNING To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFTY INSTRUCTION before operating this appliance. OVERVIEW OF THE CONTROL PANEL DV405* 1 2 3 4 5 6 7 8 9 DV398* DV395* DV393* 1 Cycle Selector To select a cycle, rotate the Cycle Selector dial to the desired cycle. The indicator light by the cycle name will illuminate.
Load should be under 3 pounds. The Wool cycle of this machine has been approved by Woolmark company for Total-Easy-Care Wool products, M0913 (DV405). The DV393,DV395 and DV398 models are not endorsed by The Woolmark Company. 02 operating Instructions, tips Sanitize - Sanitizes garments by infusing high temperature heat deep into the fabric during the drying cycle. Use this course to keep your bedding and curtains clean through sanitization.
operating Instructions, tips Dry Level Selection Button To select the dry level in the Normal, Heavy Duty, or other Sensor Dry cycles, press the Dry Level button. An indicator light will illuminate next to the desired dryness level. Press the button repeatedly to scroll through the settings. Larger or bulkier loads may require the Very Dry or More Dry setting for complete dryness.
DRUM LIGHT Lights the dryer drum while the dryer is running. Turning On and Off You can turn the Drum Light on and off while your dryer is running and when it is stopped. If you do not turn the Drum Light off within 5 minutes of turning it on, it is automatically turned off. DELAY START You can set the dryer to start your course automatically at a later time, choosing a delay time. The hour displayed indicates the time at which the course will be started. 1. Set your drying course. 2.
operating Instructions, tips VENT SENSOR Your Samsung dryer is equipped with a Vent Sensor, which detects and notifies you when it is time to clean the ductwork. Keep your dryer safe and efficient by cleaning the ducts when prompted. The Vent Sensor detects any duct blockages You can figure out whether there is a duct blockage from the “Vent Sensor digital display. Level Message Status ” lamp of the Solution 0 The “Vent Sensor lamp is turned off. ” The ductwork is free from blockages.
SMART CARE This function enables you to check the status of the dryer using a smartphone. 02 operating Instructions, tips 1. Press and hold the Smart Care button for 3 seconds to use the Smart Care function when an error occurs or if you do not press any buttons since you turn on the dryer. • The error code history is deleted after using the function. 2.
operating Instructions, tips RACK DRY Installing the drying rack 1. Open the dryer door. 2. Position the drying rack in tumbler, placing the front lip of the drying rack on the top of the lint filter. 3. Place the rear legs in the two recessed areas of the dryer’s back wall then push down the middle of the drying rack to fix it in place. 4. Place the items to be dried on the rack, leaving space between them so air can circulate. 5. Close the dryer door. 6.
CLEAN THE LINT FILTER • • • After each load. To shorten drying time. To operate more energy efficiently. Frame Front Filter Door LOAD THE DRYER PROPERLY • • • • Place only one washload in your dryer at a time. Mixed loads of heavy and lightweight fabrics will dry differently, which may result in lightweight fabrics being dry while heavy fabrics remain damp at the end of a drying cycle. Add one or more similar items to your dryer when only one or two articles of clothing need drying.
care and cleaning CONTROL PANEL Clean with a soft, damp cloth. Do not use abrasive substances. Do not spray cleaners directly on the panel. The control panel finish may be damaged by some laundry pre-treatment soil and stain remover products. Apply such products away from your dryer and wipe up any spills or overspray immediately. TUMBLER Remove any stains caused by crayon, ink, fabric dye (from new items such as towels or jeans), and so on with an allpurpose cleaner.
special laundry tips SPECIAL LAUNDRY TIPS Bedspreads & Comforters • • • Blankets • • Curtains & Draperies • • Follow the care label instructions or dry on the Normal cycle and High temperature. Make sure the item is thoroughly dry before using or storing. May require repositioning to ensure even drying. Use Normal cycle and dry only one blanket at a time for best tumbling action. Make sure the item is thoroughly dry before using or storing.
troubleshooting CHECK THESE POINTS IF YOUR DRYER… PROBLEM SOLUTION Doesn’t run. • • • • Make sure the door is latched shut. Be sure the power cord is plugged into a live electrical outlet. Check the home’s circuit breaker and fuses. Press the Start/Pause button again if the door is opened during the cycle. Doesn’t heat. • • • • Check the home’s circuit breaker and fuses. On a gas dryer, check that the gas supply is on. Clean the lint filter and exhaust duct.
PROBLEM SOLUTION Shuts off before load is dry • Dryer load is too small. Add more items or a few towels and restart the cycle. Dryer load is too large. Remove some items and restart the dryer. • • Make sure the lint filter is cleaned before every load. With some loads that produce high amounts of lint, it may be necessary to clean the filter during the cycle.
appendix FABRIC CARE CHART The following symbols provide garment care direction. The Clothing care labels include symbols for washing, bleaching, drying, and ironing, or dry cleaning when necessary. The use of symbols ensures consistency among garment manufacturers of domestic and imported items. Follow care label directions to maximize garment life and reduce laundering problems.
PROTECTING THE ENVIRONMENT DECLARATION OF CONFORMITY This appliance complies with UL2158. 06 appendix This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance, please observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be connected to a power source. Remove the door so that animals and small children cannot get trapped inside the appliance.
appendix CYCLE CHART ( : factory setting, : selectable) Cycle Sensor Dry Functions Max Load Size Recommended Item Sensor Dry Level Normal Cottons, Work clothes, Linen, Mixed loads Normal dry Heavy Duty Heavy fabrics such as jean, Corduroys, Heavywork clothes Normal dry Perm Press Shirts, Synthetic fabrics, Knits, Wrinkle-free cottons, Permanent Normal dry Bedding PLUS / Bedding Bulky items such asblankets, Sheets, Comforters, Pillows Normal dry Towels Bath towels and similar items Nor
warranty (U.S.A) SAMSUNG DRYER LIMITED WARRANTY TO ORIGINAL PURCHASER This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC.
EXCEPT AS SET FORTH HEREIN, THERE ARE NO WARRANTIES ON THIS PRODUCT EITHER EXPRESS OR IMPLIED, AND SAMSUNG DISCLAIMS ALL WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. NO WARRANTY OR GUARANTEE GIVEN BY ANY PERSON, FIRM, OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG.
warranty(CANADA) SAMSUNG DRYER LIMITED WARRANTY TO ORIGINAL PURCHASER This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS CANADA, INC.
EXCEPT AS SET FORTH HEREIN, THERE ARE NO WARRANTIES ON THIS PRODUCT EITHER EXPRESS OR IMPLIED, AND SAMSUNG DISCLAIMS ALL WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. NO WARRANTY OR GUARANTEE GIVEN BY ANY PERSON, FIRM, OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG.
note DV405ETPAWR_03021F-08_EN_130820.
bit.ly/samsungwashers QUESTIONS OR COMMENTS? Country CALL OR VISIT US ONLINE AT U.S.A 1-800-SAMSUNG (726-7864) www.samsung.com MEXICO 01-800-SAMSUNG (726-7864) www.samsung.com CANADA 1-800-SAMSUNG (726-7864) www.samsung.com/ca (English) www.samsung.com/ca_fr (French) Visits by a Service Engineer to explain functions, maintenance or installation is not covered by warranty. Please contact your Samsung call agent for help with any of these issues. Code No.
DV405* DV395* DV393* DV398* Secadora a gas y eléctrica manual del usuario Este manual está impreso en papel 100% reciclado imagine las posibilidades Gracias por adquirir este producto Samsung. Para recibir un servicio más completo o los accesorios, registre su producto en o contacte con www.samsung.com/register 1-800-SAMSUNG(726-7864) DV405ETPAWR_03021F-08_MES_130820.
características 1. Capacidad extra grande ¡Las capacidades de secado ultra al alcance de la mano! Ahora puede secar cargas extra grandes. Nuestra secadora ultra grande de 7.4 pies cúbicos de capacidad hace circular más aire entre su ropa, secándola más rápido, para obtener un resultado sin arrugas. 2. Smart Care (DV405* Solamente) El sistema automático de supervisión de fallas Smart Care de Samsung detecta y diagnóstica problemas tempranamente y proporciona una solución fácil y rápida. 3.
instrucciones de seguridad Felicitaciones por la compra de la nueva secadora Samsung. Este manual contiene información importante acerca de la instalación, el uso y el cuidado del electrodoméstico. Lea detenidamente estas instrucciones a fin de aprovechar al máximo los múltiples beneficios y funciones de la secadora. ADVERTENCIA - Riesgo de incendio • • • • La instalación de la secadora de ropa debe estar a cargo de un instalador calificado.
instrucciones de seguridad INSTRUCCIONES DE SEGURIDAD IMPORTANTES ADVERTENCIA ADVERTENCIA: Para reducir el riesgo de incendio, descargas eléctricas o lesiones físicas cuando usa este electrodoméstico, siga las instrucciones de seguridad básicas que figuran a continuación: 1. Lea todas las instrucciones antes de usar este electrodoméstico. 2.
QUÉ HACER SI PERCIBE OLOR A GAS: • • • • • • No intente encender ningún electrodoméstico. No encienda este electrodoméstico. No toque ningún interruptor eléctrico. No utilice ningún teléfono de su edificio. Haga que todos los ocupantes se retiren de la habitación, edificio o área. Comuníquese inmediatamente con el proveedor de gas desde el teléfono de un vecino. Siga las instrucciones del proveedor de gas. • Si no puede comunicarse con el proveedor de gas, llame al departamento de bomberos.
instrucciones de seguridad El personal técnico calificado debe efectuar una limpieza periódica del interior de la secadora y del conducto de drenaje. Este electrodoméstico debe conectarse a tierra correctamente. Nunca enchufe el cable de alimentación a un receptáculo que no esté conectado a tierra correctamente ni guarde conformidad con los códigos locales y nacionales. Consulte las instrucciones de instalación para conectar este electrodoméstico a tierra. No se siente encima de la secadora.
contenido INSTALACIÓN DE LA SECADORA 22 23 Requisitos de instalación Exterior de la secadora Requisitos para el tendido de conductos Importante para el instalador Consideraciones acerca de la ubicación Instalación del electrodoméstico en un gabinete o en un hueco Drenaje Requisitos en cuanto al gas Requisitos eléctricos Conexión a tierra Conexiones eléctricas Reemplazo de las piezas y los accesorios Herramientas necesarias para la instalación Instalación - procedimiento general Lista de verificación final d
instalación de la secadora REQUISITOS DE INSTALACIÓN Contrate a un profesional para instalar la secadora adecuadamente. En caso de que sea necesaria una visita del servicio técnico como consecuencia de una mala configuración, ajuste y conexión, se considerará responsabilidad del instalador. Si usted mismo instala la secadora, usted es el responsable. Asegúrese de tener todo lo necesario para realizar una instalación adecuada. 1. Se requiere un TOMACORRIENTE CON CONEXIÓN A TIERRA.
REQUISITOS PARA EL TENDIDO DE CONDUCTOS • • • • • • • • • • • • • • 01 instalación de la secadora • • • • • Utilice un conducto de acero galvanizado rígido o de aluminio rígido, de 4 pulgadas (10,2 cm) de diámetro. No utilice un conducto de menor tamaño. Los conductos de más de 4 pulgadas (10,2 cm) de diámetro pueden ocasionar una mayor acumulación de pelusa. Periódicamente, debe retirar la pelusa acumulada.
instalación de la secadora Si la nueva secadora se instala dentro de un sistema de drenaje existente, debe asegurarse de que: • el sistema de drenaje cumpla con todos los códigos locales, estaduales y nacionales; • no se utilice un conducto flexible de plástico; • se controle y limpie toda la pelusa acumulada del interior del conducto existente; • Compruebe que el conducto no esté enroscado o aplastado; • el regulador de tiro de la tapa de drenaje se abra y se cierre sin inconvenientes.
INSTALACIÓN DEL ELECTRODOMÉSTICO EN UN GABINETE O EN UN HUECO Laterales: 1 pulg. / 25 mm Parte superior: 17 pulg. / 432 mm Parte posterior: 5 pulg. / 127 mm Frente del gabinete: 2 pulg. / 51 mm Si la lavadora y la secadora se instalan una junto a la otra, el frente del gabinete debe contar por lo menos con una abertura de aire sin obstrucciones de 72 pulg² (465 cm²). A B 1 pulg. (2,5 cm) 1 pulg. (2,5 cm) 27 pulg. (68,6 cm) 17 pulg. (43,2 cm) 27 pulg. (68,6 cm) 1 pulg. (2,5 cm) 2 pulg.
instalación de la secadora Con pedestal opcional o kit de apilamiento Dimensiones requeridas de la instalación con pedestal 51,7 pulg. (131,4 cm) para poder abrir la puerta 39 pulg. (99,1 cm) 53,6 pulg. (136,2 cm) 341,1 pulg. (86,5 cm) 5 pulg. (12,7 cm) 27 pulg. (68,6 cm) 5 pulg. (12,7 cm) 3 pulg. (7,6 cm) 48 pulg.² * (310 cm²) 24 pulg.² * (155 cm²) 3 pulg. (7,6 cm) Gabinete o puerta 1 pulg. (2.5 cm) 31,9 pulg. (81,1 cm) 8 pulg.
DRENAJE En los Estados Unidos: • • • • • • Todas las secadoras deben tener un drenaje con salida hacia el exterior. El conducto de drenaje requerido tiene 4 pulgadas (10,2 cm) de diámetro. Utilice solamente los conductos flexibles tipo lámina metálica, si los hubiera, identificados específicamente para su utilización con la máquina por el fabricante y que cumplan con el Esquema para conductos de transición de secadora de ropa, Tema 2158A.
instalación de la secadora REQUISITOS EN CUANTO AL GAS Utilice únicamente gas natural o gas LP (gas licuado de propano). LA INSTALACIÓN DEBE REALIZARSE EN CONFORMIDAD CON LOS CÓDIGOS LOCALES, O EN AUSENCIA DE ELLOS, CON EL CÓDIGO NACIONAL PARA GAS Y COMBUSTIBLES ANSI/Z223.1, LA REVISIÓN MÁS RECIENTE (PARA LOS ESTADOS UNIDOS), O CON LOS CÓDIGOS DE INSTALACIÓN CAN/CGA-B149 (PARA CANADÁ). Las secadoras a gas están equipadas con un orificio para el quemador de modo que puedan ser utilizadas con gas natural.
REQUISITOS ELÉCTRICOS El diagrama del cableado se encuentra en la parte posterior de la secadora. • • • La conexión inadecuada del conductor de conexión a tierra del equipo puede generar una descarga eléctrica. Consulte a un electricista o técnico calificado si le surgen dudas acerca de si la conexión a tierra de su secadora es correcta. No modifique el enchufe provisto con la secadora; si no entra en el tomacorriente, solicite a un electricista calificado que instale el tomacorriente adecuado.
instalación de la secadora CONEXIONES ELÉCTRICAS Antes de poner al electrodoméstico en funcionamiento o realizar pruebas, siga las instrucciones de conexión a tierra de la sección Conexión a tierra. Se recomienda que se destine un circuito derivado individual (o separado) sólo para la secadora. NO UTILICE UN CABLE PROLONGADOR. Modelos a gas – EE.UU. y Canadá Se requiere un servicio eléctrico aprobado de CA de 120 voltios, 60 Hz, con un fusible o disyuntor de 15 A. Modelos eléctricos – Sólo EE.UU.
REEMPLAZO DE LAS PIEZAS Y LOS ACCESORIOS Si es preciso reemplazar piezas o accesorios de la secadora, comuníquese con el distribuidor al que le compró la secadora o con el centro de atención al cliente de SAMSUNG al 1-800-SAMSUNG (726-7864). 01 instalación de la secadora HERRAMIENTAS NECESARIAS PARA LA INSTALACIÓN Reúna las herramientas y piezas necesarias antes de comenzar la instalación. Lea y siga las instrucciones provistas con cualquier herramienta enumerada aquí.
instalación de la secadora INSTALACIÓN - PROCEDIMIENTO GENERAL Para realizar una instalación adecuada, recomendamos contratar a un instalador calificado. Lea estas instrucciones en su totalidad antes de iniciar la instalación. Para instalar la secadora, siga estos pasos: 1. Mueva la secadora al lugar adecuado para la instalación. Considere instalar la secadora y la lavadora una al lado de la otra para tener fácil acceso a ambos electrodomésticos.
ADVERTENCIA 01 instalación de la secadora 6. Consulte la sección Requisitos Eléctricos, luego siga las instrucciones para conexión de sistemas de 3 cables (Paso 7) o las instrucciones para el sistema de 4 cables (Paso 8) a continuación. 7. Instrucciones para el sistema de tres cables: A. Conector a tierra externo B. Cable a tierra neutro (verde/amarillo) C. Tornillo central de color plateado del bloque de terminales D. Cable neutro (cable blanco o central) E.
instalación de la secadora MODELOS ESTADOUNIDENSES: ADVERTENCIA Riesgo de descarga eléctrica: Todos los modelos estadounidenses están fabricados para una CONEXIÓN DE SISTEMAS DE 3 CABLES. El armazón de la secadora está conectado a tierra al conductor neutro del bloque de terminales. Se requiere una CONEXIÓN DE SISTEMAS DE 4 CABLES para las construcciones nuevas o remodeladas, las casas rodantes o si los códigos locales no permiten la conexión a tierra a través del neutro.
LISTA DE VERIFICACIÓN FINAL DE LA INSTALACIÓN La secadora está enchufada a un tomacorriente y está conectada a tierra correctamente. Los conductos de drenaje están conectados y se ha colocado cinta a las uniones. Usted usó conducto rígido o flexible con un recubrimiento de metal resistente, no conducto flexible de plástico. La secadora está nivelada y apoyada firmemente sobre el piso. Para modelos a gas: El gas está abierto y no hay pérdidas de gas.
instalación de la secadora INVERSIÓN DE LA PUERTA 1. Desconecte el cable de alimentación. 2. Retire los dos tornillos de la bisagra de la puerta. 3. Levante la puerta y retírela. 8. Vuelva a colocar el tornillo en el otro orificio. 4. Retire un tornillo del frente delantero. 9. Vuelva a colocar el tornillo (paso 4) en el marco delantero. 5. Retire los dos tornillos del lado opuesto de la bisagra de la puerta. 10. Coloque la puerta sobre el lado contrario y vuelva a fijar a la secadora. 6.
CONEXIÓN DE LA MANGUERA DE ENTRADA Método1 - Uso del conector en forma de "Y" y manguera larga 01 instalación de la secadora La secadora debe conectarse a la llave de agua fría mediante las nuevas mangueras de entrada. No utilice mangueras viejas. 1. Cierre la llave de agua fría. 2. Si tiene una manguera de agua de la lavadora conectada a Conector Y la llave de agua fría, desatornille y quite la manguera. 3.
instalación de la secadora Método2 - Uso de la manguera corta, la manguera larga y el conector en forma de "Y" La secadora debe conectarse a la llave de agua fría mediante las nuevas mangueras de entrada. No utilice mangueras viejas. Si el conector en forma de "Y" no puede conectarse directamente a la llave de agua fría, debe utilizar la manguera corta. 1. Cierre la llave de agua fría. Manguera corta 2.
manual de instrucciones, sugerencias ADVERTENCIA Para reducir el riesgo de incendio, descarga eléctrica o lesiones personales, lea las INSTRUCCIONES DE SEGURIDAD IMPORTANTES antes de poner en funcionamiento el aparato. DESCRIPCIÓN GENERAL DEL PANEL DE CONTROL DV405* 2 3 4 5 6 7 8 9 02 manual de instrucciones, sugerencias 1 DV398* DV395* DV393* 1 Selector de ciclos Para seleccionar un ciclo, gire el disco Selector de ciclos hasta llegar al ciclo deseado.
manual de instrucciones, sugerencias Las cargas deben tener un peso inferior a las 3 lb. El ciclo de Lana de esta máquina ha sido aprobado por Woolmark Company para productos de lana Total-Easy-Care M0913 (DV405). Los modelos DV393, DV395 y DV398 no están avalados por The Woolmark Company. Sanitize (Desinfección): desinfecta las prendas impregnando la tela con calor a alta temperatura durante el ciclo de secado.
Botón de selección Dry Level (Nivel de secado) Para seleccionar el nivel de secado en los ciclos Normal (Normal), Heavy Duty (Servicio pesado), u otros ciclos Sensor Dry (Secado con sensor), presione el botón Dry Level (Nivel de secado). Se iluminará una luz en el indicador junto al nivel de secado deseado. Presione el botón repetidamente para desplazarse por las opciones.
manual de instrucciones, sugerencias SEGURO PARA NIÑOS Evita que los niños jueguen con la secadora. Configuración/Liberación Si desea activar o desactivar esta función, presione simultáneamente los botones Time (Tiempo) y Signal (Señal) durante 3 segundos. Detalles del Seguro para niños - Puede activar el Seguro para niños mientras su secadora está en funcionamiento.
MI CICLO Le permite seleccionar, guardar y activar un ciclo a medida que incluye las opciones Dry Level (Nivel de secado), Temp (Temperatura) opción de tiempo, etc. en otro momento. Para utilizar My Cycle (Mi ciclo) siga estos pasos: 1. Presione el botón My Cycle (Mi ciclo). El indicador de My Cycle (Mi ciclo) se iluminará. 2. Seleccione el ciclo que desea incluir utilizando el disco Selector de ciclos. 3. Seleccione y configure las opciones (Dry Level (nivel de secado), Temp (Temperatura), etc.) 4.
manual de instrucciones, sugerencias SMART CARE Esta función permite comprobar el estado de la secadora con un teléfono inteligente. 1. Mantenga presionado el botón Smart Care durante 3 segundos para usar la función Smart Care cuando se produce un error o si no presiona ningún botón cuando la alimentación está encendida. • El historial de los códigos de error se borra luego de usar la función. 2.
SECADO EN ESTANTE Instalación del estante de secado Estante de secado Puerta PRENDAS SUGERIDAS OPCIONES DE TEMP.
manual de instrucciones, sugerencias LIMPIE EL FILTRO PARA PELUSAS • • • Después de cada carga. Para reducir el tiempo de secado. Para hacer uso de la energía con mayor eficacia. No haga funcionar la secadora sin el filtro para pelusas colocado. Marco delantero Filtro Puerta CARGUE LA SECADORA DE MANERA ADECUADA • • • • Coloque sólo una carga de ropa en la secadora por vez.
cuidado y limpieza PANEL DE CONTROL TAMBOR Elimine todas las manchas causadas por crayón, tinta o tintura de la tela (proveniente de artículos nuevos, tales como toallas o jeans) etc, con un limpiador común. Posteriormente, seque las toallas o prendas viejas para eliminar restos de manchas o solución de limpieza. Una vez que se hayan seguido estos pasos, es posible que las manchas aún sean visibles, pero no se transferirán a las cargas subsiguientes.
sugerencias para prendas especiales SUGERENCIAS PARA PRENDAS ESPECIALES Siga las instrucciones del fabricante o de la etiqueta de indicaciones para secar prendas especiales. Si no se dispone de etiquetas con indicaciones, use la siguiente información como guía. Cubrecamas y edredones • • • Ropa de cama • • Cortinas y paños de tela • • Siga las instrucciones de la etiqueta o seque en el ciclo Normal (Normal) y con temperatura High (Alta).
guía de solución de problemas CONTROLE ESTOS PUNTOS SI SU SECADORA… SOLUCIÓN No funciona. • • • • No calienta. • • • • No seca. • • • • • • • • • Hace ruido. • • • • No seca de manera uniforme. • • Asegúrese de que la puerta esté cerrada con traba. Asegúrese de que el cable de alimentación esté enchufado a un tomacorriente que funcione. Controle los disyuntores y fusibles de la casa. Presione el botón Start/Pause (Inicio/Pausa) nuevamente si la puerta se abre durante el ciclo.
guía de solución de problemas PROBLEMA SOLUCIÓN Tiene olor. • • Se apaga antes de que la carga esté seca • • Pelusa en las prendas • • • • Los olores del hogar, ya sea que provengan de pintura, barniz, limpiadores potentes, etc., pueden ingresar en la secadora con el aire del ambiente. Esto es normal puesto que la secadora extrae el aire de la habitación, lo calienta y lo hace circular por el tambor y lo expulsa a través del drenaje hacia el exterior.
CÓDIGOS DE INFORMACIÓN Pueden aparecer códigos de información para ayudarle a comprender mejor qué ocurre con la secadora. SIGNIFICADO SOLUCIÓN tE Filtro para pelusas obstruido La ventilación está obstruida Limpie el filtro o el conducto de ventilación. Si el problema continúa, llame al servicio técnico. HE Temperatura de calentamiento cuando la secadora está funcionando. Comuníquese con el servicio técnico. dE La secadora funciona con la puerta abierta Cierre la puerta y luego reinicie.
apéndice TABLA DE INDICACIONES SOBRE LA TELA Los siguientes símbolos ofrecen indicaciones acerca de las prendas. La etiqueta de indicaciones de la prenda incluye símbolos para lavado, blanqueado, secado y planchado, o limpieza a seco cuando sea necesaria. El uso de símbolos garantiza la consistencia entre los fabricantes textiles de artículos nacionales e importados. Siga las indicaciones de la etiqueta para prolongar la vida útil de la prenda y reducir los problemas del lavado.
PROTECCIÓN DEL MEDIO AMBIENTE DECLARACIÓN DE CONFORMIDAD Este electrodoméstico cumple con la norma UL2158. 06 apéndice Este electrodoméstico se fabrica con materiales reciclables. Si decide desechar este electrodoméstico, siga la normativa local relacionada con la eliminación de desechos. Corte el cable de alimentación para que el electrodoméstico no pueda conectarse a una fuente de alimentación.
apéndice TABLA DE CICLOS ( : configurado en fábrica, : seleccionable) Ciclo Funciones Tamaño de carga máxima Prendas recomendadas Nivel de secado con sensor Normal Algodón, ropa de trabajo, ropa de cama, cargas mezcladas Normal dry (Secado normal) Potencia extra Telas resistentes, tales como jeans, corderoy y ropa de trabajo pesado Normal dry (Secado normal) Camisas, telas sintéticas, tejidos, prendas de algodón sin arrugas y telas que requieren planchado permanente Ropa de cama PLUS / Prendas
garantía (U.S.A) SECADORA SAMSUNG GARANTÍA LIMITADA PARA EL COMPRADOR ORIGINAL El presente producto de la marca SAMSUNG, tal como lo provee y distribuye SAMSUNG ELECTRONICS AMERICA, INC.
SALVO LO ESTABLECIDO EN LA PRESENTE GARANTÍA, NO EXISTEN GARANTÍAS SOBRE EL PRESENTE PRODUCTO, YA SEAN EXPRESAS O TÁCITAS, Y SAMSUNG DESCONOCE TODAS LAS GARANTÍAS QUE INCLUYEN, AUNQUE NO EN CARÁCTER TAXATIVO, CUALQUIER GARANTÍA TÁCITA DE QUE EL PRODUCTO SE ENCUENTRA EN CONDICIONES APTAS PARA LA VENTA, DE DEFRAUDACIÓN DE DERECHOS O DE QUE EL PRODUCTO SE ADECUA A LOS FINES ESPECÍFICOS PARA LOS CUALES SE ADQUIERE.
garantía (CANADA) SECADORA SAMSUNG GARANTÍA LIMITADA PARA EL COMPRADOR ORIGINAL El presente producto de la marca SAMSUNG, tal como lo provee y distribuye SAMSUNG ELECTRONICS CANADA, INC.
SALVO LO ESTABLECIDO EN LA PRESENTE GARANTÍA, NO EXISTEN GARANTÍAS SOBRE EL PRESENTE PRODUCTO, YA SEAN EXPRESAS O TÁCITAS, Y SAMSUNG DESCONOCE TODAS LAS GARANTÍAS QUE INCLUYEN, AUNQUE NO EN CARÁCTER TAXATIVO, CUALQUIER GARANTÍA TÁCITA DE QUE EL PRODUCTO SE ENCUENTRA EN CONDICIONES APTAS PARA LA VENTA, DE DEFRAUDACIÓN DE DERECHOS O DE QUE EL PRODUCTO SE ADECUA A LOS FINES ESPECÍFICOS PARA LOS CUALES SE ADQUIERE.
memo DV405ETPAWR_03021F-08_MES_130820.
¿TIENE PREGUNTAS O COMENTARIOS? País LLAME AL O VISÍTENOS EN LÍNEA EN U.S.A 1-800-SAMSUNG (726-7864) www.samsung.com MEXICO 01-800-SAMSUNG (726-7864) www.samsung.com CANADA 1-800-SAMSUNG (726-7864) www.samsung.com/ca (English) www.samsung.com/ca_fr (French) Las visitas del personal de servicio técnico para explicar funciones, mantenimiento o instalación no están cubiertas por la garantía. Póngase en contacto con su agente del centro de llamadas Samsung para que le asesore.
DV405* DV395* DV393* DV398* Sèche-linge à gaz et électrique manuel d'utilisation Ce manuel a été imprimé sur du papier 100% recyclé. un monde de possibilités Nous vous remercions d'avoir choisi ce produit Samsung. Si vous souhaitez recevoir un service plus complet ou des accessoires, enregistrez votre produit à l'adresse ci-dessous ou contactez www.samsung.com/register 1-800-SAMSUNG (726-7864) DV405ETPAWR_03021F-08_CFR_130820.
caractéristiques 1. Très grande capacité La très grande capacité de séchage est désormais accessible à tous ! Vous pouvez désormais faire sécher d'importants volumes de linge en une seule fois. D'une capacité plus qu'exceptionnelle de 7,4 pieds cubes, ce sèche-linge fait circuler plus d'air à travers vos vêtements les séchant plus vite et en réduisant le froissement. 2.
consignes de sécurité Félicitations pour l’achat de votre nouveau sèche-linge Samsung. Ce manuel contient de précieuses informations sur l’installation, l’utilisation et l’entretien de votre appareil. Prenez le temps de le lire pour tirer pleinement profit de tous les avantages et de toutes les fonctionnalités de votre sèche-linge. AVERTISSEMENT - Risque d'incendie • • • • L'installation du sèche-linge doit être effectuée par un technicien qualifié.
consignes de sécurité CONSIGNES IMPORTANTES DE SÉCURITÉ AVERTISSEMENT AVERTISSEMENT : afin de réduire les risques d'incendie, d'électrocution ou de blessures physiques lors de l'utilisation de l'appareil, des précautions de base doivent être prises : 1. Lisez toutes les consignes de sécurité avant d'utiliser l’appareil. 2.
QUE FAIRE EN CAS D’ÉMANATION DE GAZ : • • • • • • Ne tentez pas d'allumer un appareil électrique. Ne mettez pas l’appareil sous tension. Ne touchez à aucun interrupteur électrique. N’utilisez aucun téléphone dans le bâtiment. Faites évacuer tous les occupants de la pièce, du bâtiment ou du secteur. Appelez immédiatement votre fournisseur de gaz depuis le téléphone d'un voisin. Suivez les consignes que vous recevrez. • Si vous ne pouvez pas joindre votre fournisseur de gaz, appelez les pompiers.
consignes de sécurité L’intérieur du sèche-linge et du conduit d’évacuation doit être nettoyé régulièrement, par un technicien de maintenance qualifié. Cet appareil doit être correctement mis à la terre. Ne branchez jamais le cordon d’alimentation sur une prise qui n’est pas correctement reliée à la terre et qui n’est pas conforme aux réglementations locales et nationales en vigueur. Consultez les consignes d’installation pour relier cet appareil à la terre. Ne vous asseyez pas sur le sèche-linge.
table des matières INSTALLATION DU SÈCHE-LINGE 13 14 15 15 16 17 17 18 21 22 23 24 Conditions d'installation Extérieur du sèche-linge Conditions requises en matière de conduits Remarque importante pour l’installateur Choix de l’emplacement d’installation Encastrement dans une niche ou installation dans un placard Évacuation Systèmes fonctionnant au gaz Normes électriques Mise à la terre Raccordement électrique Pièces de rechange et accessoires Outils requis pour l'installation Installation : procédure gén
installation du sèche-linge CONDITIONS D'INSTALLATION Laissez un professionnel installer correctement votre sèche-linge. Si vous contactez le service aprèsvente suite à une installation, des réglages ou un branchement mal exécutés, la responsabilité relève de l'installateur. Si c'est vous qui avez installé le sèche-linge, la responsabilité vous incombe. Vérifiez que vous disposez de tous les éléments requis pour installer correctement l’appareil, comme suit. 1. Une PRISE ÉLECTRIQUE AVEC MISE A LA TERRE.
CONDITIONS REQUISES EN MATIÈRE DE CONDUITS • • • • • • • • • • • • • • • • • • 01 installation du sèche-linge • Utilisez un conduit en aluminium ou en acier galvanisé rigide d’un diamètre de 4 pouces (10,2 cm). N’utilisez pas de conduit plus petit. Les conduits dont le diamètre est supérieur à 4 pouces (10,2 cm) peuvent favoriser l'accumulation de peluches. Retirez régulièrement les peluches accumulées. Si vous devez utiliser un conduit métallique flexible, optez pour un conduit aux parois rigides.
installation du sèche-linge Si un nouveau sèche-linge est relié à un système d’évacuation existant, vous devez veiller à ce que : • Le système d’évacuation soit conforme aux réglementations locales, régionales et nationales. • Aucun conduit flexible en plastique ne soit utilisé. • Le conduit existant soit contrôlé et les peluches accumulées à l’intérieur retirées. • Le conduit ne doit être ni entortillé ni écrasé. • Le registre de la hotte s’ouvre et se ferme sans problème.
ENCASTREMENT DANS UNE NICHE OU INSTALLATION DANS UN PLACARD DÉGAGEMENTS MINIMAUX POUR INSTALLATION ENCASTRÉE : Sur le dessus – 17 po / 432 mm À l'avant – 2 po / 51 mm Si le lave-linge et le sèche-linge sont installés ensemble, prévoyez un dégagement d'au moins 72 po² (465 cm²) à l'avant du placard.
installation du sèche-linge Avec un socle ou un kit de superposition facultatif Dimensions requises pour l’installation avec socle 51,7 po (131,4 cm) pour permettre l’ouverture du hublot 39 po (99,1 cm) 53,6 po (136,2 cm) 341,1 po (86,5 cm) 5 po (12,7 cm) 27 po (68,6 cm) 5 po (12,7 cm) 3 po (7,6 cm) 48 po² * (310 cm²) 24 po² * (155 cm²) 3 po (7,6 cm) Placard ou hublot 1 po (2,5 cm) 31,9 po (81,1 cm) 8 po** (20,3 cm) Dimensions requises pour l’installation avec kit de superposition 6 po * (15,2 cm
ÉVACUATION L'évacuation du sèche-linge ne doit pas être reliée à un conduit de cheminée, un mur, un plafond, un grenier, un espace mansardé ou exigu d'un bâtiment. L’évacuation du sèche-linge vers l’extérieur évite le refoulement d’air humide et de peluches dans la pièce. • • • • • • Tous les sèche-linge doivent être dotés d’une évacuation vers l’extérieur. Le diamètre du conduit d’évacuation doit être de 4 po (10,16 cm).
installation du sèche-linge SYSTÈMES FONCTIONNANT AU GAZ Utilisez uniquement du gaz naturel ou du propane liquide (PL). L’INSTALLATION DOIT ÊTRE CONFORME AUX RÉGLEMENTATIONS LOCALES EN VIGUEUR OU, EN L’ABSENCE DE DISPOSITIONS SPÉCIFIQUES, À LA RÉGLEMENTATION NATIONALE SUR LE GAZ COMBUSTIBLE ANSI/Z223,1 (NATIONAL FUEL GAS CODE), DERNIÈRE RÉVISION (POUR LES ÉTATS-UNIS) OU AUX DISPOSITIONS D’INSTALLATION CAN/CGA-B149 (POUR LE CANADA).
NORMES ÉLECTRIQUES Le schéma de câblage est situé à l'arrière du sèche-linge. • • • Un branchement incorrect du conducteur de mise à la terre peut représenter un risque de surtension électrique. Demandez conseil à un électricien ou un réparateur agréé si vous avez des doutes quant à la mise à la terre de l’appareil. Ne modifiez pas la prise fournie avec le sèche-linge. Si celle-ci ne correspond pas à la prise secteur, demandez à un électricien qualifié d’installer une prise adéquate.
installation du sèche-linge RACCORDEMENT ÉLECTRIQUE Avant toute mise en marche ou test, observez les consignes de mise à la terre présentées dans la section Mise à la terre. Nous vous recommandons de relier votre sèche-linge à une dérivation individuelle ou à un circuit distinct. N’UTILISEZ PAS DE RALLONGE AVEC CET APPAREIL. Modèles au gaz : États-Unis et Canada Vous devez utiliser une alimentation électrique de 120 V c.a., 60 Hz et un disjoncteur ou fusible de 15 A.
PIÈCES DE RECHANGE ET ACCESSOIRES Si vous avez besoin de pièces de rechange ou d’accessoires pour votre sèche-linge, contactez votre revendeur ou le centre d’assistance clientèle de SAMSUNG au 1-800-SAMSUNG (726-7864). 01 installation du sèche-linge OUTILS REQUIS POUR L'INSTALLATION Regroupez et vérifiez les pièces et outils requis avant de commencer l’installation. Lisez et respectez les instructions fournies avec les outils répertoriés ici.
installation du sèche-linge INSTALLATION : PROCÉDURE GÉNÉRALE Pour une installation optimale, nous vous recommandons de faire appel à un installateur qualifié. Lisez intégralement les consignes avant de commencer l'installation. Pour installer le sèche-linge, suivez les étapes ci-dessous : 1. Installez votre sèche-linge à l’emplacement approprié. Vous pouvez par exemple installer le sèche-linge et le lave-linge côte à côte.
AVERTISSEMENT 01 installation du sèche-linge 6. Consultez la section Normes électriques, puis suivez les consignes sur les branchements à 3 fils (Étape 7) ou à 4 fils (Étape 8) ci-dessous. 7. Consignes sur les branchements à trois fils : A. Connecteur de terre externe B. Fil de terre neutre (vert/jaune) C. Vis centrale argentée du bornier D. Fil neutre (blanc ou central) E Réducteur de tension ¾” (1,9 cm) homologué UL 1. Desserrez ou retirez la vis centrale du bornier. 2.
installation du sèche-linge MODÈLES POUR LES ÉTATS-UNIS : AVERTISSEMENT Risque d'électrocution : Tous les modèles destinés aux États-Unis sont conçus pour un BRANCHEMENT À 3 FILS. Le châssis du sèche-linge est relié à la terre par un conducteur neutre au niveau du bornier. Un BRANCHEMENT À 4 FILS est requis dans les cas suivants : nouvelles constructions, habitations rénovées, mobil homes, réglementations locales n’autorisant pas la mise à la terre via le conducteur neutre.
LISTE DE CONTRÔLE FINAL POUR L’INSTALLATION Le sèche-linge est branché sur une prise électrique et correctement relié à la terre. Les conduites d'évacuation sont installées et les joints maintenus par du ruban adhésif. Nous avons choisi un système d'évacuation en métal rigide ou flexible et non des flexibles plastique. Le sèche-linge est de niveau et ses pieds sont posés au sol de manière stable. Pour les modèles à gaz : l'arrivée de gaz est ouverte et aucune fuite de gaz n'est détectée.
installation du sèche-linge CONSEILS POUR L’ÉVACUATION DU SÈCHE-LINGE Les conduits en plastique ou non métalliques représentent un danger potentiel d’incendie. AVERTISSEMENT 1. Assurez-vous que le sèche-linge a été installé de manière à ce que l’évacuation de l’air se fasse sans problème. 2. Utilisez un conduit d’évacuation métallique rigide de 4”. Scellez tous les joints à l’aide d’un ruban adhésif, y compris au niveau du sèche-linge. N’utilisez jamais de vis, qui entraînent l’accumulation de peluches.
INVERSION DU HUBLOT 8. Réengagez les vis dans les autres trous. 4. Retirez une vis de l’avant du cadre 9. Réengagez la vis (étape 4) à l'avant du cadre 5. Retirez les deux vis sur le côté opposé de la charnière du hublot. 10. Placez le hublot de l’autre côté et refixez-le sur le sèche-linge. 6. Retirez les deux vis du dispositif de fermeture. 11. Remontez le dispositif de fermeture. 7. Retirez une vis de la charnière du hublot. 12. Replacez les vis dans les trous restants.
installation du sèche-linge RACCORDEMENT DU TUYAU D’ARRIVÉE D'EAU Méthode 1 : avec un raccord en Y et un tuyau long Le sèche-linge doit être connecté au robinet d’eau froide à l’aide d’un tuyau d’arrivée neuf. N’utilisez jamais de tuyaux usagés. 1. Fermez le robinet. 2. Si le tuyau d'eau du lave-linge est raccordé au robinet d'eau froide, débranchez-le. 3. Si l'espace libre est suffisant, branchez l'extrémité femelle en laiton du raccord en Y au robinet d'eau froide. Serrez fermement à la main. 4.
Méthode 2 : avec un tuyau court, un tuyau long et un raccord en Y Tuyau long Ne serrez pas à l'excès ; vous risqueriez d'endommager le raccord. 01 installation du sèche-linge 02 Le sèche-linge doit être connecté au robinet d’eau froide à l’aide d’un tuyau d’arrivée neuf. N’utilisez jamais de tuyaux usagés. Si vous ne pouvez brancher directement le raccord en Y sur le robinet d'eau froide, vous devez utiliser le tuyau court fourni avec le sèche-linge. 1. Fermez le robinet. Tuyau court 2.
instructions et conseils d’utilisation AVERTISSEMENT Afin de limiter les risques d'incendie, d'électrocution ou de blessures, consultez la section CONSIGNES IMPORTANTES DE SÉCURITÉ avant d'utiliser cet appareil. PRÉSENTATION DU PANNEAU DE COMMANDES DV405* 1 2 3 4 5 6 7 8 9 DV398* DV395* DV393* 1 Sélecteur de programme Pour choisir un cycle, positionnez le sélecteur sur le programme de votre choix. Le témoin lumineux s’allume en regard du programme.
Charge inférieure à 3 livres. Le programme Wool (Laine) de ce sèche-linge a été approuvé par Woolmark pour les lainages Total-Easy-Care, M0913 (DV405). Les modèles DV393, DV395 et DV398 ne sont pas approuvés par la société Woolmark. 2 3 Affichage numérique La fenêtre d’affichage indique la durée restante estimée pour le programme, après activation du bouton Start/Pause (Démarrer/Pause). La durée estimée restante peut varier au fur et à mesure de la progression du programme.
instructions et conseils d’utilisation Bouton Niveau de séchage Pour sélectionner le niveau de séchage en mode Normal (Normal), Heavy Duty (Grand rendement) ou d’autres programmes avec capteur de séchage, appuyez sur le bouton Appuyez plusieurs fois sur le bouton pour faire défiler les différents paramètres. Pour obtenir un séchage parfait sur des volumes de linge plus importants, vous pouvez utiliser les paramètres Very Dry (Séchage très fort) ou More Dry (Séchage fort). Dry Level (Niveau de séchage).
ÉCLAIRAGE DU TAMBOUR Cette fonction permet d'éclairer le tambour lorsque le sèche-linge est en marche. Activation/Désactivation L’éclairage du tambour peut être activé ou désactivé lorsque le sèche-linge fonctionne ou non. Si vous ne désactivez pas la fonction Drum Light (Éclairage du tambour) dans les 5 minutes suivant son activation, celle-ci s’éteindra automatiquement.
instructions et conseils d’utilisation CAPTEUR DE VENTILATION Votre sèche-linge Samsung est équipé d’un capteur de ventilation qui détecte et vous prévient lorsque les conduits doivent être nettoyés. Conservez votre sèche-linge propre et efficace en nettoyant les conduits lorsque vous y êtes invité. Le capteur de ventilation détecte tous les colmatages de conduit Vous pouvez voir s’il y a un colmatage de conduit à partir du voyant du capteur de ventilation « Vent Sensor » de l’affichage numérique.
ENTRETIEN INTELLIGENT Cette fonction vous permet de vérifier l'état du sèche-linge à l'aide d'un téléphone intelligent. 02 instructions et conseils d’utilisation 1. Appuyez sur le bouton Smart Care (Entretien intelligent) en le maintenant enfoncé pendant 3 secondes pour utiliser la fonction si une erreur se produit ou si vous n'avez actionné aucun bouton depuis la mise en marche du seche-linge. • L'historique du code d'erreur est supprimé après l'utilisation de la fonction. 2.
instructions et conseils d’utilisation SUPPORT DE SÉCHAGE Installation du support de séchage 1. Ouvrez le hublot du sèche-linge. 2. Placez la grille de séchage dans le tambour, en positionnant son bord avant sur le dessus du filtre à peluches. 3. Encastrez les deux pieds arrière dans les orifices prévus à cet effet sur la paroi arrière du sèche-linge, puis appuyez au centre du support de séchage pour la mettre en place. 4.
NETTOYAGE DU FILTRE À PELUCHES • • • Après chaque séchage. Pour réduire la durée de séchage. Pour un meilleur rendement énergétique. Panneau avant Filtre Hublot CHARGEMENT DU SÈCHE-LINGE • • • • N'introduisez qu'une seule charge de linge lavé à la fois dans votre sèche-linge. Un mélange de textiles épais et légers séchera différemment ; ainsi, à la fin du programme de séchage, les textiles légers risquent d'être secs alors que les textiles épais seront encore humides.
entretien et nettoyage PANNEAU DE COMMANDES nettoyez-le avec un chiffon doux et humide. N’utilisez pas de produits abrasifs. Ne vaporisez aucun produit d'entretien directement sur le panneau de commande. Certains détachants pour tissu peuvent endommager le revêtement du panneau de commandes. Appliquez donc ces produits à l'écart de votre sèche-linge et essuyez immédiatement toute projection ou tout excès.
conseils d'entretien du linge CONSEILS D'ENTRETIEN DU LINGE Couvre-lits et couettes • • • Couvertures • • Rideaux et tentures • • Observez les symboles de l’étiquette ou sélectionnez le programme de séchage Normal (Normal) et la température High (Élevée) Assurez-vous que l'article est complètement sec avant de l'utiliser ou de le ranger. Il est parfois nécessaire de repositionner l'article dans le sèche-linge pour assurer un séchage homogène.
dépannage VÉRIFIEZ LES POINTS SUIVANTS SI VOTRE SÈCHE-LINGE... PROBLÈME SOLUTION Ne se met pas en route. • • • • Assurez-vous que le hublot est bien fermé. Vérifiez que le cordon d'alimentation est branché sur une prise électrique opérationnelle. Vérifiez le disjoncteur et les fusibles de votre domicile. Appuyez de nouveau sur le bouton Start/Pause (Démarrer/Pause) en cas d'ouverture du hublot en cours de programme. Ne chauffe pas. • • • • Vérifiez le disjoncteur et les fusibles de votre domicile.
PROBLÈME SOLUTION S'arrête avant que le linge ne soit sec. • • • • Assurez-vous que le filtre est propre avant chaque cycle. Sur les charges produisant beaucoup de peluches, il peut être nécessaire de nettoyer le filtre en cours de cycle. Certains textiles produisent une grande quantité de peluches (ex. : serviettes en coton). C’est pourquoi ces articles doivent être séchés séparément des textiles qui attirent les peluches (ex. : pantalon en velours).
annexe TABLEAU DES SYMBOLES TEXTILES Les symboles suivants fournissent des conseils d'entretien des vêtements. Les étiquettes d'entretien des vêtements incluent des symboles relatifs au lavage, au blanchiment, au séchage, au repassage et au nettoyage à sec, le cas échéant. L'utilisation de ces symboles garantit la cohérence des informations entre les fabricants de vêtements (articles domestiques ou importés).
PROTECTION DE L’ENVIRONNEMENT DÉCLARATION DE CONFORMITÉ Cet appareil est conforme à la norme UL2158. 06 annexe Cet appareil a été fabriqué à partir de matériaux recyclables. Si vous décidez de le jeter, veuillez respecter les normes locales en matière d’évacuation des déchets. Coupez le cordon d’alimentation de façon à ce que l’appareil ne puisse pas être raccordé à une source électrique. Enlevez le hublot pour que des animaux et des jeunes enfants ne se retrouvent pas piégés à l’intérieur de l’appareil.
annexe TABLEAU DES PROGRAMMES ( : réglage usine, : sélectionnable) Programme Séchage normal Serviettes Stérilisation Literie, rideaux, vêtements d'enfant Très fort (aucun changement) Repassage facile Literie PLUS/Literie Séchage manuel Cycles vapeur Fonctions Niveau du capteur de séchage Coton, vêtements de travail, lin, charges mixtes Pièces au tissu épais, tels que les jeans, les velours côtelés ou les vêtements de travail Chemises, tissus synthétiques, lainages, tissus infroissables en coton,
garantie (U.S.A) SÈCHE-LINGE SAMSUNG GARANTIE LIMITÉE À L'ACHETEUR INITIAL Ce produit de la marque SAMSUNG, fourni, distribué par SAMSUNG ELECTRONICS AMERICA, INC.
Cette garantie limitée ne couvre pas les problèmes résultant d'un courant, d'une tension ou d'une alimentation électrique incorrects, ainsi que d'ampoules électriques, de fusibles ou de câblage inappropriés. Elle ne couvre pas non plus le coût des appels au service d'assistance pour obtenir des instructions ou la réparation des erreurs d'installation. SAMSUNG ne garantit pas que l'appareil sera exempt de tout problème ou qu'il fonctionnera sans interruption.
garantie (CANADA) SÈCHE-LINGE SAMSUNG GARANTIE LIMITÉE À L'ACHETEUR INITIAL Ce produit de la marque SAMSUNG, fourni, distribué par SAMSUNG ELECTRONICS CANADA, INC.
Cette garantie limitée ne couvre pas les problèmes résultant d'un courant, d'une tension ou d'une alimentation électrique incorrects, ainsi que d'ampoules électriques, de fusibles ou de câblage inappropriés. Elle ne couvre pas non plus le coût des appels au service d'assistance pour obtenir des instructions ou la réparation des erreurs d'installation. SAMSUNG ne garantit pas que l'appareil sera exempt de tout problème ou qu'il fonctionnera sans interruption.
mémo DV405ETPAWR_03021F-08_CFR_130820.
DES QUESTIONS OU DES COMMENTAIRES ? Pays APPELEZ LE OU RENDEZ-VOUS SUR LE SITE U.S.A 1-800-SAMSUNG (726-7864) www.samsung.com MEXICO 01-800-SAMSUNG (726-7864) www.samsung.com CANADA 1-800-SAMSUNG (726-7864) www.samsung.com/ca (English) www.samsung.com/ca_fr (French) Les visites des techniciens de maintenance destinées à expliquer les fonctions, la maintenance ou l’installation n’est pas couverte par la garantie.