SC20F70 Series SC07F80 Series Vacuum Cleaner user manual ✻ Please read the User Manual thoroughly before operating the vacuum. ✻ For indoor use only. English Thank you for purchasing a Samsung product. To receive a more complete service, please register your product at www.samsung.com/register DJ68-00701L-00.indb 01 2013. 12. 2.
Contents YOUR VACUUM CLEANER 07 BEFORE USING THE VACUUM CLEANER 08 OPERATING CLEANER 12 MAINTENANCE 15 08 09 09 10 Assembly Using the UV brush (Option) Installing the Dust Sensor (Option) Using accessory 12 12 12 13 14 Power cord Check filter ON/OFF Power control Dust Sensor (Option) 15 Cleaning the dust bin and grille 18 Cleaning the outlet filter 19 Maintain floor tools TROUBLESHOOTING 22 DJ68-00701L-00.indb 02 2013. 12. 2.
Safety information SAFETY INFORMATION WARNING WARNING • Before operating the appliance, please read this manual thoroughly and retain it for your reference. • Because the following operating instructions cover various models, the characteristics of your vacuum cleaner may differ slightly from those described in this manual. CAUTION/WARNING SYMBOLS USED WARNING CAUTION Indicates that a risk of death or serious injury exists. Indicates that a risk of personal injury or material damage exists.
IMPORTANT SAFEGUARDS GENERAL • Read all instructions carefully. Before switching on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate on the bottom of the cleaner. • WARNING : Do not use the vacuum cleaner when rug or floor is wet. Do not use to suck up water. • Close supervision is necessary when any appliance is used by or near children. Do not allow the vacuum cleaner to be used as a toy. Do not allow the vacuum cleaner to run unattended at any time.
• • • • • • • Children shall not play with the appliance. Cleaning and user maintenance shall not be done by children without supervision. Children should be supervised to ensure that they do not play with the appliance. The plug must be removed from the socket outlet before cleaning or maintaining the appliance. The use of an extension cord is not recommended. If your vacuum cleaner is not operating correctly, switch off the power supply and consult an authorized service agent.
• When the UV lamp is out of order, never disassemble or modify the product yourself. Please contact the manufacturer or service center for a replacement. • Since an internal discharge occurs within the UV Brush, never use the product near an inflammable spray or substance. • Take care not to touch the UV lamp window after using the UV Brush for an extended period of time as the surface of the window may be hot.
Your vacuum cleaner Handle Combination accessory Pipe 01 YOUR VACUUM CLEANER Hose 2-Step brush Cyclone OPTION (Depending on model) * SC20F70U / SC07F80U Series Power turbo plus * Parquet master * Cover battery * Dust sensor * Mini turbo * Pipe * Handle * Furniture brush * UV brush * 2-in-1 accessory * Your vacuum cleaner _07 DJ68-00701L-00.indb 07 2013. 12. 2.
Before using the vacuum cleaner ASSEMBLY Connecting the Hose Connecting the handle and pipe Connecting the brush 08_ Before using the vacuum cleaner DJ68-00701L-00.indb 08 2013. 12. 2.
USING THE UV BRUSH (OPTION) Connecting the brush into the hose handle 02 BEFORE USING THE VACUUM CLEANER There will be a “clicking” sound when the UV brush has been installed securely on the hose handle. For safety reasons, UV brushing only runs for 30 minutes and then stops operating. To resume the operation, press the [BRUSH ON/OFF] button again. CAUTION The UV brush, which is assembled into the hose handle (not directly connected to the pipe), is dedicated for bedclothes.
USING ACCESSORY Combination accessory (Option) 2 1 Dusting brush Crevice tool Accessories (Option) Install the accessory to the handle. Dusting brush Crevice tool Dusting brush - For cleaning moldings, carved articles. etc. Crevice tool - For cleaning in folds, crevices and corners. 10_ Before using the vacuum cleaner DJ68-00701L-00.indb 10 2013. 12. 2.
Pipe Adjust the length of the pipe by sliding the length control button located in the center of the telescopic pipe. 02 BEFORE USING THE VACUUM CLEANER For storage, park the floor nozzle CAUTION Do not pick up a machine while the floor nozzle parked. Before using the vacuum cleaner _11 DJ68-00701L-00.indb 11 2013. 12. 2.
Operating cleaner POWER CORD CAUTION When removing the plug from the electrical outlet, grasp the plug, not the cord. CHECK FILTER ON/OFF The filter light is illuminated when the dust pack requires checking or emptying. 12_ Operating cleaner DJ68-00701L-00.indb 12 2013. 12. 2.
POWER CONTROL Hose (controlled by radio frequency signals) ON/OFF SC20F70H / SC07F80H Series Transmitter 03 OPERATING CLEANER Select a lower power / higher power Select a quiet mode -/+ SC20F70U / SC07F80U Series Transmitter Select a lower power / higher power UV brush ON/OFF • UV sterilization cannot be activated by itself. • Press the [SUCTION (-/+)] and [BRUSH ON/OFF] for operation. • Don’t cover the handle transmitter when you use a handle control.
DUST SENSOR (OPTION) Dust Sensor Operations • Indicates the amount of dust being picked up and passing by the sensor which assist the user to clean more efficiently. • The dust sensor is activated au tomatically when the cleaner runs and is turned off when the cleaner is stopped. Green : Amount of dust passing sensor is small. Red : Amount of dust passing sensor is large. If the red light does not light up when cleaning a dusty location - Clean the sensors (2EA) with a dry cloth.
Maintenance CLEANING THE DUST BIN AND GRILLE Empty the dust bin, if dust reaches 'MAX' or Check filter ( ) light is illuminating. Push the button aside. Turn the grille and take out it. 04 MAINTENANCE Take the dust bin out by lifting the handle. 1 2 3 4 Maintenance _15 DJ68-00701L-00.indb 15 2013. 12. 2.
Push the button. Separate the dust bin from body. Clean the dust bin and body with water. Leave the dust bin and body in the shade until completely dry. CAUTION 5 6 7 Install the grille and turn to clockwise. 1 2 16_ Maintenance DJ68-00701L-00.indb 16 2013. 12. 2.
CLEANING THE DUST FILTER 1 3 Shake the filter to remove dust, then wash the filter. 04 MAINTENANCE Pull the dust bin cover to open. 2 Remove the filter from the dust bin. 4 Let the filter dry for more than 12 hours. 5 Put the filter into the dust bin. Make sure the filter is completely dry before putting it back into the vacuum cleaner. Allow 12 hours for it to dry. Do not use wet filter. Replace the dust filter if it becomes damaged or deformed.
CLEANING THE OUTLET FILTER 1 2 Take the dust bin out by lifting the handle. 3 Pull out the HEPA Filter. 4 Shake the HEPA Filter to clean. Install the filter and holder in main body. • The filter can be replaced and separated from holder by pulling. • Clean the outlet filter when suction is noticeably reduced continuously or the vacuum cleaner abnormal overheads. Note: HEPA Filters are not washable. Replace filter if cleaning does not resolve the problem.
MAINTAIN FLOOR TOOLS 2-Step Brush 04 MAINTENANCE • Adjust the inlet lever according to the floor surface. Carpet Floor • Remove waste matter completely if the inlet is blocked. Power Turbo Plus Brush (Optional Accessory) 1 2 3 4 1 2 Frequent vacuuming of hair or pet fur may reduce cleaning effectiveness over time due to matters tangled around the drum. In this case, clean the drum with care. Maintenance _19 DJ68-00701L-00.indb 19 2013. 12. 2.
To remove dust from the dust bin of the UV brush (Option) When the dust bin is filled, turn the [Dust Removal] switch to empty the dust bin. • While the cleaner is operating (suction), the vacuum will suck the material from the dust bin to the main unit. • While the [Dust Removal] switch is in the position, the suction power of the cleaner is reduced.
Mini turbo brush (Optional Accessory) - To check brushroll 04 MAINTENANCE Check brushroll, when a clog is present or debris is visible. - To check belt Inspect belt to ensure that it is in good condition. If belt is broken or cracked, replace belt according to instructions. Maintenance _21 DJ68-00701L-00.indb 21 2013. 12. 2.
Troubleshooting PROBLEM SOLUTION Motor does not start. • Check cable, pulg and socket. • Leave to cool. Suction force is gradually decreasing. • Check for blockage and remove. In operation, the vacuum cleaner stops • Please unclog the intake. after repeating runs and stops three times. Cord does not rewind fully. • Pull the cord out 2-3 m and push down the cord rewind button. Vacuum cleaner dows not pick up dirt. • Check hose and replace if required. Low or decreasing suction.
Memo DJ68-00701L-00.indb 23 2013. 12. 2.
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. Country Customer Care Center ☎ Web Site AUSTRIA 0810 - SAMSUNG (7267864, € 0.07/min) SWITZERLAND 0848 - SAMSUNG(7267864, CHF 0.08/ min) www.samsung.com www.samsung.com/ch www.samsung.com/ch_fr (French) DJ68-00701L-00.indb 24 2013. 12. 2.
Serie SC20F70 Serie SC07F80 Staubsauger Benutzerhandbuch ✻ Lesen Sie diese Bedienungsanleitung sorgfältig durch, bevor Sie das Gerät verwenden. ✻ Nur zum Einsatz in geschlossenen Räumen geeignet. Deutsch Vielen Dank, dass Sie sich für ein Gerät von Samsung entschieden haben. Wenn Sie umfassenderen Service wünschen, registrieren Sie Ihr Gerät unter www.samsung.com/register DJ68-00701L-00.indb 01 2013. 12. 2.
Inhalt GERÄTEKOMPONENTEN 07 VOR DER VERWENDUNG DES GERÄTS 08 VERWENDEN DES GERÄTS 12 PFLEGE 15 08 09 09 10 Befestigen der Gerätekomponenten Verwenden der UV-Bürste (optional) Einsetzen des Staubsensors (optional) Verwenden der Saugaufsätze 12 12 12 13 14 Netzkabel Filteranzeige Netztaste Leistungseinstellung Staubsensor (optional) 15 Reinigen von Staubbehälter und Filter 18 Reinigen des Raumluftfilters 19 Pflege der Bürstenaufsätze FEHLERBEHEBUNG 22 DJ68-00701L-00.indb 02 2013. 12. 2.
Sicherheitsinformationen SICHERHEITSINFORMATIONEN WARNUNG WARNUNG • Lesen Sie vor Verwendung des Geräts die Bedienungsanleitung gründlich durch, und bewahren Sie sie zum späteren Nachschlagen auf. • Da die folgenden Hinweise zum Betrieb für verschiedene Modelle gelten, können die Eigenschaften Ihres Geräts leicht von den in dieser Bedienungsanleitung beschriebenen Merkmalen abweichen.
WICHTIGE SICHERHEITSHINWEISE ALLGEMEIN • Lesen Sie alle Anweisungen sorgfältig durch. Vergewissern Sie sich vor dem Einschalten, dass die Spannung Ihrer Stromversorgung mit der auf dem Typenschild auf der Unterseite des Saugers übereinstimmt. • WARNUNG: Verwenden Sie das Gerät nicht, wenn der Teppich oder Boden nass ist. Verwenden Sie es nicht, um Wasser aufzusaugen. • Wenn Haushaltsgeräte in der Nähe von Kindern betrieben werden, ist eine sorgsame Aufsicht notwendig.
• • • • • • • mit verminderten körperlichen, sensorischen oder geistigen Fähigkeiten oder einem Mangel an Erfahrung und Wissen nur bedient werden, wenn sie unter Aufsicht stehen oder eine Unterweisung zum sicheren Umgang mit dem Gerät erhalten haben und die damit verbundenen Gefahren verstehen. Kinder dürfen nicht mit dem Gerät spielen. Kinder dürfen das Gerät nur unter Aufsicht reinigen oder warten. Kinder müssen beaufsichtigt werden, um zu verhindern, dass sie mit dem Gerät spielen.
• • • • • • Gegenständen. Der Hersteller haftet für keinerlei Verluste aufgrund von Unfällen, die durch die Verwendung der UV-Bürste für andere als die oben genannten Zwecke entstehen. Setzen Sie sich nicht auf die UV-Bürste, lassen Sie sie nicht fallen, und vermeiden Sie Krafteinwirkung. Andernfalls können Schäden am Gerät oder Verletzungen die Folgen sein. Berühren Sie die Kontakte auf der Rückseite der UV-Bürste niemals mit metallischen Gegenständen.
Gerätekomponenten Handgriff Kombi-Aufsatz Rohr 01 GERÄTEKOMPONENTEN Schlauch Zweistufenbürste Zyklonfilter OPTIONAL (je nach Modell) * Serien SC20F70U / SC07F80U Turbo-Kraftbürste * Parkettbürste * Mini-Turbobürste * Rohr * Handgriff * Batterien und Abdeckung * Staubsensor * Polsterbürste * UV-Bürste * 2-in-1Saugaufsätze * Gerätekomponenten _07 DJ68-00701L-00.indb 07 2013. 12. 2.
Vor der Verwendung des Geräts BEFESTIGEN DER GERÄTEKOMPONENTEN Befestigen des Schlauchs Befestigen von Handgriff und Rohr Befestigen der Bürste 08_ Vor der Verwendung des Geräts DJ68-00701L-00.indb 08 2013. 12. 2.
VERWENDEN DER UV-BÜRSTE (OPTIONAL) Schieben Sie die Bürste auf den Saugstutzen am Schlauchgriff. 02 VOR DER VERWENDUNG DES GERÄTS Wenn die UV-Bürste muss hörbar am Saugstutzen des Schlauchgriffs einrasten, damit sie sicher befestigt ist. Aus Sicherheitsgründen läuft die UV-Bürste nur 30 Minuten lang. Dann wird sie ausgeschaltet. Wenn Sie sie weiterhin verwenden möchten, drücken Sie erneut die Taste „Brush ON/OFF (Bürste EIN/AUS)“.
VERWENDEN DER SAUGAUFSÄTZE Kombi-Aufsatz (optional) 2 1 Staubbürste Flachdüse Saugaufsätze (optional) Die Saugaufsätze werden in Saugstutzen am Schlauchgriff geschoben. Staubbürste Flachdüse Staubbürste - Zum Reinigen von Zierleisten und Einrichtungsgegenständen mit Schnitzereien. Flachdüse - Zum Reinigen von Zwischenräumen, Spalten und Ecken. 10_ Vor der Verwendung des Geräts DJ68-00701L-00.indb 10 2013. 12. 2.
Rohr Mit Hilfe der Längeneinstellung in der Mitte des Teleskoprohrs können Sie die Länge des Rohrs anpassen. 02 VOR DER VERWENDUNG DES GERÄTS Wenn Sie das Gerät wegstellen, bringen Sie die Bodendüse an der entsprechenden Halterung an. VORSICHT Heben Sie das Gerät nicht an, solange die Bodendüse an der Halterung angebracht ist. Vor der Verwendung des Geräts _11 DJ68-00701L-00.indb 11 2013. 12. 2.
Verwenden des Geräts NETZKABEL VORSICHT Fassen Sie den Stecker selbst und nicht das Kabel an, wenn Sie den Stecker aus der Steckdose ziehen. FILTERANZEIGE NETZTASTE Die Filteranzeige leuchtet, wenn die Filtereinheit überprüft oder geleert werden muss. 12_ Verwenden des Geräts DJ68-00701L-00.indb 12 2013. 12. 2.
LEISTUNGSEINSTELLUNG Handgriffsteuerung (Steuerung über Funksignale) Netztaste Serien SC20F70H / SC07F80H Sender 03 VERWENDEN DES GERÄTS Auswählen einer niedrigeren/höheren Leistungsstufe Auswählen des Flüsterbetriebs -/+ Serien SC20F70U / SC07F80U Auswählen einer niedrigeren/höheren Leistungsstufe Sender UV-Bürste EIN/AUS (ON/OFF) • Die UV-Funktion zum Desinfizieren wird nicht automatisch eingeschaltet.
STAUBSENSOR (OPTIONAL) Funktion des Staubsensors • Gibt die Staubmenge an, die vom Gerät aufgenommen und am Sensor vorbei geleitet wird, um eine effizientere Reinigung zu ermöglichen. • Der Staubsensor wird automatisch aktiviert, wenn das Gerät eingeschaltet wird und deaktiviert sich, wenn das Gerät ausgeschaltet wird. Grün: Die am Sensor vorbei geleitete Staubmenge ist gering. Rot: Die am Sensor vorbei geleitete Staubmenge ist hoch.
Pflege REINIGEN VON STAUBBEHÄLTER UND FILTER Fassen Sie den Staubbehälter am Griff, und ziehen Sie ihn nach oben heraus. Schieben Sie die Verriegelung zur Seite. Drehen Sie den Filter aus dem Staubbehälter heraus. 1 04 PFLEGE Leeren Sie den Staubbehälter, wenn der sich darin befindende Staub die MAX-Markierung ) erreicht hat oder wenn die Filteranzeige ( leuchtet. 2 3 4 Pflege _15 DJ68-00701L-00.indb 15 2013. 12. 2.
Drücken Sie die abgebildete Taste. Trennen Sie den Staubbehälter vom Gehäuse. 5 Reinigen Sie den Staubbehälter und das Gehäuse mit Wasser. 6 Lassen Sie Staubbehälter und Gehäuse im Schatten vollständig trocknen. 7 VORSICHT Setzen Sie den Filter durch drehen im Uhrzeigersinn wieder ein. 1 2 16_ Pflege DJ68-00701L-00.indb 16 2013. 12. 2.
REINIGEN DER FILTEREINHEIT 1 2 04 PFLEGE Entfernen Sie die Abdeckung des Staubbehälters. 3 Beseitigen Sie losen Staub durch Schütteln des Filters, und waschen Sie ihn anschließend aus. Entnehmen Sie den Filter aus dem Staubbehälter. 4 Lassen Sie den Filter mehr als 12 Stunden lang trocknen. 5 Setzen Sie den Filter in den Staubbehälter ein. Achten Sie darauf, dass der Filter vollständig getrocknet ist, bevor Sie ihn wieder in das Gerät einsetzen. Lassen Sie ihn mindestens 12 Stunden lang trocknen.
REINIGEN DES RAUMLUFTFILTERS 1 2 Fassen Sie den Staubbehälter am Griff, und ziehen Sie ihn nach oben heraus. 3 Ziehen Sie die HEPA-Filtereinheit heraus. 4 Schütteln Sie die HEPA-Filtereinheit zum Reinigen aus. Setzen Sie die Filtereinheit mit der Halterung wieder in das Gehäuse des Geräts ein. • Die Filtereinheit kann von der Halterung abgezogen und ausgetauscht werden. • Reinigen Sie den Raumluftfilter, wenn die Saugkraft deutlich immer weiter abnimmt oder das Gerät sich stärker als normal erhitzt.
PFLEGE DER BÜRSTENAUFSÄTZE Zweistufenbürste 04 PFLEGE • Stellen Sie den Saughöhenhebel entsprechend der Bodenbeschaffenheit ein. Teppich Glatte Böden • Entfernen Sie Rückstände am Aufsatz vollständig, wenn der Einlass verstopft ist. Turbo-Kraftbürste (optional) 1 2 3 4 1 2 Durch häufiges Saugen von Haaren und Tierfell kann es passieren, dass die Reinigungsleistung wegen der in der Lauftrommel eingefangenen Rückstände im Laufe der Zeit zurückgeht. Reinigen Sie in diesem Fall vorsichtig die Lauftrommel.
Entleeren des Staubbehälters der UV-Bürste (optional) Wenn der Staubbehälter voll ist, können Sie ihn mit Hilfe des Drehknaufs zum Entleeren des Staubbehälters leeren. • Im Betrieb wird das im Staubbehälter befindliche Material zum Saugschlitten gesaugt. • Wenn der Drehknauf zum Entleeren in steht, verringert sich die der Position Saugleistung des Geräts.
Mini-Turbobürste (optional) - Überprüfen der Bürstenrolle 04 PFLEGE Überprüfen Sie die Bürstenrolle, wenn die Bürste mit Material verstopft ist oder sich Schmutz angesammelt hat. - Überprüfen des Riemens Kontrollieren Sie den Riemen, um sicherzustellen, dass er sich in gutem Zustand befindet. Wenn der Riemen gebrochen oder rissig ist, ersetzen Sie ihn entsprechend den Anweisungen zum Austauschen des Riemens. Pflege _21 DJ68-00701L-00.indb 21 2013. 12. 2.
Fehlerbehebung PROBLEM LÖSUNG Der Motor startet nicht. • Überprüfen Sie Kabel, Stecker und Steckdose. • Lassen Sie das Gerät abkühlen. Die Saugkraft nimmt allmählich ab. • Suchen Sie nach Verstopfungen, und entfernen Sie sie ggf. Das Gerät bricht den • Überprüfen Sie den Einlass auf Verstopfungen, und entfernen Betrieb nach mehreren Sie diese ggf. Saugvorgängen immer wieder ab.
Notizen DJ68-00701L-00.indb 23 2013. 12. 2.
DJ68-00701L-00.indb 24 2013. 12. 2.
Série SC20F70 Série SC07F80 Aspirateur manuel d'utilisation ✻ Avant d’utiliser l'aspirateur, lisez attentivement le manuel d'utilisation. ✻ Utilisation intérieure uniquement. Français Merci d'avoir choisi un produit Samsung. Afin de bénéficier d'un service plus complet, veuillez enregistrer votre produit à l'adresse www.samsung.com/register DJ68-00701L-00.indb 01 2013. 12. 2.
Sommaire VOTRE ASPIRATEUR 07 AVANT D'UTILISER L'ASPIRATEUR 08 UTILISATION DE L'ASPIRATEUR 12 MAINTENANCE 15 08 Montage 09 Utilisation de la brosse UV (en option) 09 Installation du capteur de poussière (en option) 10 Utilisation des accessoires 12 12 12 13 14 Cordon d'alimentation Vérification du filtre MARCHE/ARRÊT Contrôle de la puissance Capteur de poussière (en option) 15 Nettoyage du réservoir à poussière et du support de grille 18 Nettoyage du filtre de sortie 19 Entretien des brosses DÉPANNAGE
Consignes de sécurité CONSIGNES DE SÉCURITÉ AVERTISSEMENT AVERTISSEMENT • Avant d'utiliser cet appareil, veuillez lire attentivement ce manuel et le conserver pour toute référence ultérieure. • Les instructions d'utilisation suivantes concernent plusieurs modèles ; il est donc possible que les caractéristiques de votre aspirateur soient légèrement différentes de celles spécifiées dans ce manuel.
CONSIGNES DE SÉCURITÉ IMPORTANTES GÉNÉRALITÉS • Lisez attentivement toutes les instructions. Avant d'allumer l'appareil, assurez-vous que la tension de votre alimentation électrique correspond à celle indiquée sur la plaque signalétique située sous l'aspirateur. • DANGER : N'utilisez pas l'aspirateur si le tapis ou le sol à nettoyer est mouillé. N'utilisez pas l'aspirateur pour aspirer de l'eau. • En cas d'utilisation par un enfant ou à proximité d'un enfant, soyez extrêmement vigilant.
• • • • • • • physiques, sensorielles ou mentales réduites, ou un manque d’expérience et de connaissances, à moins qu’elles ne soient surveillées ou qu’elles aient reçu les instructions nécessaires concernant l’utilisation de cet appareil de la part d’une personne responsable, et ce, pour leur propre sécurité. Les enfants ne doivent pas jouer avec l’appareil. Le nettoyage et la maintenance de l’appareil ne doivent pas être effectués par des enfants sans surveillance.
• • • • • • La société ne sera pas tenue pour responsable d'aucune perte due à des accidents suite à l'utilisation de la brosse UV à des fins autres que son but original comme indiqué ci-dessus. Ne vous asseyez pas sur la brosse UV ni ne la laissez pas tomber, et évitez les chocs sur l'appareil. Le non-respect de cette consigne risquerait de provoquer une blessure ou d'endommager l'appareil. Ne touchez pas les bornes d'alimentation situées au dos de la brosse UV avec une pointe ou une tige en métal.
Votre aspirateur Poignée Accessoire combiné Tube 01 VOTRE ASPIRATEUR Flexible Brosse 2 positions Cyclone OPTION (selon modèle) * Séries SC20F70U/SC07F80U Puissance Turbo Plus * Brosse pour parquet * Mini turbo * Tube * Poignée * Cache de la batterie * Capteur de poussière * Brosse pour meubles * Brosse UV * Accessoire 2 en 1* Votre aspirateur _07 DJ68-00701L-00.indb 07 2013. 12. 2.
Avant d'utiliser l'aspirateur MONTAGE Connexion du flexible Connexion de la poignée et du tube Connexion de la brosse 08_ Avant d'utiliser l'aspirateur DJ68-00701L-00.indb 08 2013. 12. 2.
UTILISATION DE LA BROSSE UV (EN OPTION) Connexion de la brosse dans la poignée du flexible 02 AVANT D'UTILISER L'ASPIRATEUR Vous entendrez un « clic » lorsque la brosse UV est correctement insérée dans la poignée du flexible. Pour des raisons de sécurité, le brossage UV fonctionne pendant 30 minutes uniquement puis il s'arrête. Pour relancer le fonctionnement, appuyez à nouveau sur le bouton [Brush ON/OFF] (MARCHE/ARRÊT Brosse).
UTILISATION DES ACCESSOIRES Accessoire combiné (en option) 2 1 Brosse à épousseter Suceur plat Accessoires (en option) Installez l'accessoire au niveau de la poignée. Brosse à épousseter Suceur plat Brosse à épousseter - Pour nettoyer des articles moulés ou sculptés, etc. Suceur plat - Pour nettoyer dans des plis, interstices et recoins. 10_ Avant d'utiliser l'aspirateur DJ68-00701L-00.indb 10 2013. 12. 2.
Tube Réglez la longueur du tube en faisant glisser le bouton de contrôle de la longueur situé au centre du tube télescopique. ATTENTION 02 AVANT D'UTILISER L'ASPIRATEUR Avant d'entreposer l'aspirateur, fixez le suceur à parquets sur sa position de rangement. Ne soulevez pas l'aspirateur lorsque le suceur à parquets est fixé sur sa position de rangement. Avant d'utiliser l'aspirateur _11 DJ68-00701L-00.indb 11 2013. 12. 2.
Utilisation de l'aspirateur CORDON D'ALIMENTATION ATTENTION Lorsque vous débranchez la fiche d'une prise électrique, tenez la fiche, non le cordon. VÉRIFICATION DU FILTRE MARCHE/ARRÊT Le témoin du filtre s'allume lorsque le groupe filtrant doit être vérifié ou vidé. 12_ Utilisation de l'aspirateur DJ68-00701L-00.indb 12 2013. 12. 2.
CONTRÔLE DE LA PUISSANCE Flexible (commandé par signaux radioélectriques) MARCHE/ARRÊT Séries SC20F70H/SC07F80H Émetteur 03 UTILISATION DE L'ASPIRATEUR Pour augmenter/réduire la puissance Pour sélectionner un mode silencieux -/+ Séries SC20F70U/SC07F80U Émetteur Pour augmenter/réduire la puissance MARCHE/ARRÊT de la brosse UV • La stérilisation UV ne peut pas être activée par elle-même.
CAPTEUR DE POUSSIÈRE (EN OPTION) Fonctionnement du capteur de poussière • Indique la quantité de poussière qui est aspirée et passe devant le capteur, ce qui permet à l'utilisateur de nettoyer de manière plus efficace. • Le capteur de poussière s'active automatiquement à l'allumage de l'aspirateur et s'éteint avec l'arrêt de ce dernier. Vert : la quantité de poussière qui passe devant le capteur est faible. Rouge : la quantité de poussière qui passe devant le capteur est importante.
Maintenance NETTOYAGE DU RÉSERVOIR À POUSSIÈRE ET DU SUPPORT DE GRILLE Pour extraire le réservoir à poussière, soulevez la poignée. Faites glisser le bouton sur le côté. Faites tourner le support de la grille pour l'extraire. 1 04 MAINTENANCE Videz le réservoir de poussière lorsque la poussière atteint le repère « MAX » ou lorsque ) le symbole de vérification du filtre ( s'allume. 2 3 4 Maintenance _15 DJ68-00701L-00.indb 15 2013. 12. 2.
Appuyez sur le bouton. Retirez le réservoir à poussière du corps. 5 Nettoyez le réservoir à poussière et le corps de l'aspirateur à l'eau claire. 6 Laissez-les entièrement sécher à l'abri du soleil. 7 ATTENTION Insérez le support de grille et faites-le tourner en sens horaire. 1 2 16_ Maintenance DJ68-00701L-00.indb 16 2013. 12. 2.
NETTOYAGE DU FILTRE À POUSSIÈRE 1 3 Secouez le filtre pour éliminer la poussière, puis lavez le filtre à l'eau claire. Retirez le filtre du réservoir à poussière. 4 04 MAINTENANCE Tirez le couvercle du réservoir à poussière pour l'ouvrir. 2 Laissez-le sécher pendant 12 heures minimum. 5 Replacez le filtre dans le réservoir à poussière. Veillez à ce que le filtre soit totalement sec avant de le replacer dans l'aspirateur. Laissez-le sécher pendant 12 heures. N'utilisez pas un filtre mouillé.
NETTOYAGE DU FILTRE DE SORTIE 1 2 Pour extraire le réservoir à poussière, soulevez la poignée. 3 Tirez sur le filtre HEPA pour le retirer. 4 Secouez le filtre HEPA pour le nettoyer. Remettez en place le filtre et son support dans le corps de l'aspirateur. • Pour séparer le filtre de son support afin de le remplacer, tirez sur chacun des deux éléments. • Lorsque la puissance d'aspiration est constamment réduite ou l'aspirateur surchauffe anormalement, nettoyez le filtre de sortie.
ENTRETIEN DES BROSSES Brosse 2 positions 04 MAINTENANCE • Réglez la manette d'aspiration en fonction de la surface à nettoyer. Moquette Sol dur • Retirez les saletés entièrement si l'orifice d'aspiration est bouché. Brosse Puissance Turbo Plus (accessoire proposé en option) 1 2 3 4 1 2 Une aspiration fréquente de cheveux ou de poils d’animaux peut affecter l'efficacité du nettoyage dans le temps en raison d’un enchevêtrement de ces éléments autour du tambour.
Retirer la poussière du réservoir à poussière de la brosse UV (accessoire proposé en option) Lorsque le réservoir à poussière est plein, utilisez le bouton de « Retrait de la poussière » pour vider la poussière. • Pendant le fonctionnement (l'aspiration) de l'appareil, le vide aspire la poussière du réservoir vers l'unité principale. • Lorsque le bouton de « Retrait de la , la poussière » est sur la position puissance d'aspiration de l'aspirateur est réduite.
Mini turbo brosse (accessoire proposé en option) - Vérifier la brosse rouleau 04 MAINTENANCE Vérifiez la brosse rouleau lorsque vous constatez un colmatage ou la présence de débris. - Vérifier la courroie Contrôlez l’état de la courroie pour vous assurer qu'elle est en bon état. Si celle-ci présente des fissures ou des cassures, remplacez-la en suivant les instructions. Maintenance _21 DJ68-00701L-00.indb 21 2013. 12. 2.
Dépannage PROBLÈME SOLUTION Le moteur ne démarre pas. • Vérifiez le câble, la fiche et la prise. • Laissez-le refroidir. La puissance d'aspiration diminue progressivement. Pendant l'utilisation, l'aspirateur s'arrête après s'être éteint et rallumé trois fois. Le cordon ne se rembobine pas entièrement. • Vérifiez que rien n'obstrue l'appareil et débouchez-le si nécessaire. • Nettoyez l'entrée obstruée. • Tirez environ 2 à 3 m de cordon et appuyez sur le bouton de rembobinage. L'aspirateur n'aspire plus.
Mémo DJ68-00701L-00.indb 23 2013. 12. 2.
DJ68-00701L-00.indb 24 2013. 12. 2.
Serie SC20F70 Serie SC07F80 Aspirapolvere manuale dell'utente ✻ Leggere il Manuale dell'utente prima di utilizzare l'aspirapolvere. ✻ Solo per uso interno. Italiano Grazie per avere acquistato un prodotto Samsung. Per ricevere un servizio più completo, si prega di registrare il prodotto all'indirizzo www.samsung.com/register DJ68-00701L-00.indb 01 2013. 12. 2.
Indice L'ASPIRAPOLVERE 07 PRIMA DI UTILIZZARE L'ASPIRAPOLVERE 08 USO DELL'ASPIRAPOLVERE 12 MANUTENZIONE 15 08 Montaggio 09 Uso della spazzola UV (opzionale) 09 Installazione del Sensore polvere (opzionale) 10 Uso degli accessori 12 12 12 13 14 Cavo di alimentazione Controllare il filtro ON/OFF Regolazione potenza Sensore polvere (opzionale) 15 Pulizia della vaschetta di raccolta polvere e della griglia 18 Pulizia del filtro esterno 19 Manutenzione strumenti per pavimenti RISOLUZIONE DEI PROBLEMI 22
Informazioni sulla sicurezza INFORMAZIONI SULLA SICUREZZA ATTENZIONE ATTENZIONE • Prima di utilizzare il prodotto, leggere attentamente questo manuale e conservarlo per future consultazioni. • Poiché queste istruzioni coprono diversi modelli di prodotto, le caratteristiche dell’aspirapolvere acquistato potrebbero differire leggermente da quanto descritto in questo manuale. SIMBOLI DI AVVERTENZA/ATTENZIONE UTILIZZATI ATTENZIONE AVVERTENZA Indica il rischio di lesioni gravi perfino mortali.
PRECAUZIONI IMPORTANTI GENERALE • Leggere attentamente tutte le istruzioni. Prima di accendere il prodotto, accertarsi che le specifiche elettriche dell'abitazione siano uguali a quelle indicate sull'etichetta posta sul fondo dell'aspirapolvere. • ATTENZIONE: Non utilizzare l'aspirapolvere per pulire pavimenti o tappeti bagnati. Non aspirare acqua. • Quando si utilizzano elettrodomestici in presenza di bambini, è necessario prestare la massima attenzione. Non consentire l'uso del prodotto come giocattolo.
• • • • • • • sotto la supervisione di una persona responsabile o nel caso in cui abbiano ricevuto informazioni specifiche sull'uso sicuro dell'apparecchio e ne abbiano compreso i rischi ad esso associati. I bambini non devono giocare con l'apparecchio. La pulizia e la manutenzione dell'apparecchio non devono essere eseguite da bambini senza la supervisione di un adulto responsabile. Controllare i bambini affinché non giochino con l’apparecchio.
• • • • • il prodotto. La mancata osservanza di questa precauzione può causare lesioni o danni al prodotto. Non toccare i terminali elettrici sul retro della spazzola UV con una graffetta o una bacchetta metallica. La mancata osservanza di questa precauzione può causare scariche elettriche o incendio. Se la lampada UV non funziona, non disassemblare o modificare il prodotto autonomamente. Contattare il produttore o il centro di assistenza per richiederne la sostituzione.
L'aspirapolvere Manico Accessorio combi 01 L'ASPIRAPOLVERE Tubo flessibile Tubo telescopico Spazzola a due vie Ciclone OPZIONALE (in base al modello) * Serie SC20F70U / SC07F80U Turbo plus * Parquet * Mini turbospazzola * Tubo telescopico * Manico * Copribatteria * Sensore polvere * Spazzola per mobili * Spazzola UV * Accessorio 2 in 1 * L'aspirapolvere _07 DJ68-00701L-00.indb 07 2013. 12. 2.
Prima di utilizzare l'aspirapolvere MONTAGGIO Connessione del tubo flessibile Connessione del manico e del tubo telescopico Connessione della spazzola 08_ Prima di utilizzare l'aspirapolvere DJ68-00701L-00.indb 08 2013. 12. 2.
USO DELLA SPAZZOLA UV (OPZIONALE) Inserire la spazzola nel manico del tubo flessibile. 02 PRIMA DI UTILIZZARE L'ASPIRAPOLVERE Quando si innesta la spazzola UV nel manico del tubo flessibile si avverte un “clic”. Per motivi di sicurezza, la spazzola UV funziona solo per 30 minuti dopodiché si arresta. Per riattivarla, premere nuovamente il pulsante [BRUSH (SPAZZOLA) ON/ OFF].
USO DEGLI ACCESSORI Accessorio combi (opzionale) 2 1 Spazzola per la polvere Spazzola a spatola per caloriferi Accessori (opzionali) Innestare l'accessorio sul manico. Spazzola per la polvere Spazzola a spatola per caloriferi Spazzola per la polvere - Per la pulizia di articoli aperti o con incavi, ecc. Spazzola a spatola per caloriferi - Per la pulizia di cavità, termosifoni e angoli. 10_ Prima di utilizzare l'aspirapolvere DJ68-00701L-00.indb 10 2013. 12. 2.
Tubo telescopico Regolare la lunghezza del tubo telescopico facendo scorrere avanti e indietro il pulsante di controllo al centro. 02 PRIMA DI UTILIZZARE L'ASPIRAPOLVERE Riporre il prodotto agganciando il tubo all'unità. AVVERTENZA Non sollevare la macchina con il tubo agganciato all'unità. Prima di utilizzare l'aspirapolvere _11 DJ68-00701L-00.indb 11 2013. 12. 2.
Uso dell'aspirapolvere CAVO DI ALIMENTAZIONE AVVERTENZA Nell'estrarre il cavo di alimentazione, afferrare il cavo per la presa e non per il cavo. CONTROLLARE IL FILTRO ON/OFF La luce del filtro si illumina per segnalare la necessità effettuare un controllo o lo svuotamento dell'unità. 12_ Uso dell'aspirapolvere DJ68-00701L-00.indb 12 2013. 12. 2.
REGOLAZIONE POTENZA Tubo flessibile (controllato da segnali in radiofrequenza) ON/OFF Serie SC20F70H / SC07F80H 03 USO DELL'ASPIRAPOLVERE Trasmettitore Selezionare una potenza inferiore / superiore Selezionare una modalità silenziosa -/+ Serie SC20F70U / SC07F80U Selezionare una potenza inferiore / superiore Trasmettitore Spazzola UV ON/OFF • La sterilizzazione UV non si attiva autonomamente. • Per l’uso premere [SUCTION (ASPIRAZIONE) (-/+)] e [BRUSH (SPAZZOLA) ON/OFF].
SENSORE POLVERE (OPZIONALE) Funzionamento del Sensore polvere • Indica la quantità di polvere raccolta e passata attraverso il sensore che aiuta l'utente a pulire con maggiore efficienza. • Il sensore polvere si attiva automaticamente all'accensione dell'aspirapolvere e si disattiva al suo spegnimento. Verde: La quantità di polvere passata attraverso il sensore è ridotta. Rosso: La quantità di polvere passata attraverso il sensore è notevole.
Manutenzione PULIZIA DELLA VASCHETTA DI RACCOLTA POLVERE E DELLA GRIGLIA Svuotare la vaschetta di raccolta polvere se la polvere raggiunge il livello 'MAX' oppure, controllare se la luce del filtro ( ) è accesa. Premere il pulsante laterale. Ruotare la griglia ed estrarla. 04 MANUTENZIONE Estrarre la vaschetta di raccolta polvere sollevandone l'impugnatura. 1 2 3 4 Manutenzione _15 DJ68-00701L-00.indb 15 2013. 12. 2.
Premere il pulsante. Separare la vaschetta di raccolta polvere dal corpo dell'aspirapolvere. Pulire la vaschetta di raccolta polvere con acqua. Lasciare asciugare all'ombra la vaschetta di raccolta polvere e l'unità finché saranno completamente asciutte. AVVERTENZA 5 6 7 Inserire la griglia e ruotarla in senso orario. 1 2 16_ Manutenzione DJ68-00701L-00.indb 16 2013. 12. 2.
PULIZIA DEL FILTRO 1 3 Scuotere il filtro per rimuoverne la polvere, quindi lavarlo. Rimuovere il filtro dalla vaschetta di raccolta polvere. 4 04 MANUTENZIONE Tirare il coperchio della vaschetta di raccolta polvere per aprirla. 2 Lasciare asciugare il filtro per almeno 12 ore. 5 Rimontare il filtro nella vaschetta di raccolta polvere. Lasciare asciugare il filtro completamente prima di rimontarlo nel corpo dell'aspirapolvere. Lasciarlo asciugare per 12 ore.
PULIZIA DEL FILTRO ESTERNO 1 2 Estrarre la vaschetta di raccolta polvere sollevandone l'impugnatura. 3 Estrarre il filtro HEPA. 4 Scuotere il filtro HEPA per pulirlo. Inserire filtro e alloggiamento nell'unità. • Estrarre il filtro per sostituirlo o rimuoverlo dal suo alloggiamento. • Quando la potenza di aspirazione risulta notevolmente ridotta o l'aspirapolvere si surriscalda in modo anomalo, pulire il filtro di uscita. Nota: I filtri HEPA non sono lavabili.
MANUTENZIONE STRUMENTI PER PAVIMENTI Spazzola a due vie 04 MANUTENZIONE • Regolare la leva di ingresso in base al tipo di pavimento. Tappeti/Moquette Pavimento • Se l'ingresso è ostruito, rimuovere la sporcizia accumulata. Spazzola Turbo Plus (opzionale) 1 2 3 4 1 2 L'aspirazione frequente di capelli o peli animali, che possono arrotolarsi intorno al tamburo, può ridurre nel tempo l'efficacia della pulizia. In questo caso, pulire accuratamente il tamburo. Manutenzione _19 DJ68-00701L-00.
Per rimuovere la polvere dalla vaschetta di raccolta della spazzola UV (opzionale) Quando la vaschetta di raccolta polvere è piena, agire sul pulsante [Dust Removal (Rimozione polvere)] per svuotarla. • Quando l'aspirapolvere è in funzione (aspirazione) aspira il materiale dalla vaschetta di raccolta polvere all'unità principale. • Quando il pulsante [Dust Removal , la (Rimozione polvere)] è in posizione potenza di aspirazione dell'aspirapolvere risulta ridotta.
Mini turbospazzola (opzionale) - Verifica del rullo 04 MANUTENZIONE Verificare il rullo in caso di ostruzione o detriti evidenti. - Verifica della cinghia Ispezionare la cinghia per verificare che sia in buone condizioni. Se la cinghia presenta rotture o crepe, sostituirla con una nuova seguendo le istruzioni. Manutenzione _21 DJ68-00701L-00.indb 21 2013. 12. 2.
Risoluzione dei problemi PROBLEMA SOLUZIONE Il motore non si avvia. • Controllare il cavo, la spina e la presa elettrica. • Lasciare raffreddare l'aspirapolvere. La potenza di aspirazione diminuisce gradualmente. L'aspirapolvere si • Controllare eventuali ostruzioni e nel caso rimuoverle. arresta se, durante • Eliminare eventuali ostruzioni presenti all'ingresso il funzionamento, dell'aspirazione. vengono premuti i pulsanti di avvio e arresto per tre volte consecutive.
Memo DJ68-00701L-00.indb 23 2013. 12. 2.
DJ68-00701L-00 DJ68-00701L-00.indb 24 2013. 12. 2.