DJ68-00342J(0.0)-EN 3/29/07 10:35 AM Page 1 Operating Instructions VACUUM CLEANER ❈ Before operating this unit, please read the instructions carefully. ❈ For indoor use only. Register your product at www.samsung.
DJ68-00342J(0.0)-EN 3/29/07 10:35 AM Page 2 IMPORTANT SAFEGUARDS 1. Read all instructions carefully. Before switching on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate on the bottom of the cleaner. 2. WARNING: Do not use the vacuum cleaner when rug or floor is wet. Do not use to suck up water. 3.
DJ68-00342J(0.0)-EN 3/29/07 10:35 AM Page 3 1 ASSEMBLING THE CLEANER OPTION ▼ OPTION Features may vary according to model. Parking floor nozzle for easier storage.
DJ68-00342J(0.0)-EN 3/29/07 10:35 AM Page 4 2 OPERATING THE CLEANER 2-1 POWER CORD 2-2 ON/OFF SWITCH (BODY CONTROL TYPE ONLY) NOTE Grasp the plug to disconnect cord from the electrical outlet. 2-3 POWER CONTROL 1) HANDLE CONTROL TYPE • SLIDE TO THE STOP POSITION Vacuum cleaner switches off. (stand by mode) • SLIDE FORWARD TO MAX Suction capacity increase smoothly up to HANDLE CONTROL TYPE ONLY maximum. 2) BODY CONTROL TYPE MIN = For delicate surface e. g. net curtains.
DJ68-00342J(0.0)-EN 3/29/07 10:35 AM Page 5 2-4 AIR CONTROL To reduce suction for cleaning draperies, small rugs, and other light fabrics, pull the tap air until the hole is open.
DJ68-00342J(0.0)-EN 3/29/07 10:35 AM Page 6 2-6 USING FLOOR TOOLS Carpets CREVICE Bare floors DUSTING OPTION Detach transparent drum cover for easy cleaning.
DJ68-00342J(0.0)-EN 3/29/07 10:35 AM Page 7 3 DUST FULL INDICATOR If the "Filter Check" indicator turns to red color while you are cleaning, the dust bag requires replacement NOTE : If the "Filter Check" indicator continues to display red color even after having changed bag into new one, turn the cleaner off and check if there is any clogging in the hose,tube,floor nozzle,or on the inlet/outlet filter.
DJ68-00342J(0.0)-EN 3/29/07 10:35 AM Page 8 5 CLEANING THE CYCLONE FILTER (Optional) 1 2 3 4 5 6 6 CLEANING THE INLET FILTER 1 2 3 NOTE : Regularly check if the filter gets clogged and if so, remove the dust particles from the filter as filter clogging may cause the damage on the motor or suction decrease.
DJ68-00342J(0.0)-EN 3/29/07 10:35 AM Page 9 7 OUTLET FILTER 1 2 HEPA FILTER(option) MICRO FILTER(option) - IF YOU HAVE A PROBLEM PROBLEM Motor does not start. CAUSE No power supply. Thermal cut-out. Suction force is gradually Nozzle, suction hose or tube decreasing. is blocked. Cord does not rewind fully. Check that the cord is not twisted or wound unevenly. Vacuum cleaner does not pick up dirt. Crack or hole in hose. 8 REMEDY Check cable, plug and socket. Leave to cool.
DJ68-00342J(0.
DJ68-00342J(0.
DJ68-00342J(0.
DJ68-00342J(0.
DJ68-00342J(0.
DJ68-00342J(0.
DJ68-00342J(0.0)-EN 3/29/07 10:35 AM Page 16 DJ68-00342J REV(0.
