SSC-1000 (gb) 2009.1.
SSC-1000 (gb) 2009.1.8 1:38 PM Page 1 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
SSC-1000 (gb) 2009.1.8 1:38 PM Page 2 User’s Guide IMPORTANT SAFEGUARDS 1. Read instructions: All the safety and operating instructions should be read before the appliance is operated. 2. Retain instructions: The safety and operating instructions should be retained for future reference. 3. Heed warnings: All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow instructions: All operating and use instructions should be followed. 5.
SSC-1000 (gb) 2009.1.8 1:38 PM Page 4 User’s Guide 10. Power sources : This video product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For video products intended to operate from battery power, or other sources, refer to the operating instructions. 11.
SSC-1000 (gb) 2009.1.8 1:38 PM Page 6 User’s Guide Contents 1. Special Characteristics 1. Special Characteristics ........................................................... 7 2. Names and Functions of Each Parts ..................................... 8 3. Installation and Connection ................................................ 12 4. Setting and Manipulating .................................................... 13 5. Confirmation Matter in TImes of Abnormality Occurrence .... 22 6. Specifications .
SSC-1000 (gb) 2009.1.8 1:38 PM Page 8 User’s Guide 2. Names and Functions of Each Parts 4) MON This is used when selecting the output channel of the Matrix Switcher. It is used to select an address number in the Multiplex control mode. 5) Joy Stick This is used when the actions of the Pan/Tilt connected to the Samsung Dome Camera or the Receiver Unit is moved UP, DOWN, LEFT, or RIGHT. It is equivalent to “MOVE ( , →, , )” button in the Multiplex control mode.
SSC-1000 (gb) 2009.1.8 1:38 PM Page 10 User’s Guide 11) AUTO PAN This is used when repeatedly moving the two spots of the Pan/Tilt connected to the Samsung Dome Camera or the receiver unit. When you select the AUTO PAN Mode, LED gets turned on and when you come out LED gets turned off. 18) HOLD(SEQUENCE) This is used when stopping the Switching mode of the SEQUENCE, TOUR, and SALVO of the Matrix Switcher. It is equivalent to “SEQUENCE” button in the Multiplex control mode.
SSC-1000 (gb) 2009.1.8 1:38 PM Page 12 User’s Guide 3. Installation and Connection 4. Setting and Manipulating 1) Setting MATRIX IN RX OUT ! In order to enter into the set-up mode in the initial state, press the MENU button. DC 9V 0.6A ADAPTOR MATRIX SWITCHER SAMSUNG DOME CAMERA /RECEIVER UNIT/MULTIPLEX MATRIX IN RX OUT DC 9V 0.6A CONTROLLER 1) Connect the RS-485 Cable.
SSC-1000 (gb) 2009.1.8 1:38 PM Page 14 User’s Guide $-1 PASSWORD SETUP – For password input, move CURSOR(→) to PASSWORD SET, press ENTER, and put in the 4-digit number. – For the selection regarding whether to use a password or not, move CURSOR(→) to disable (or enable), and press ENTER. Each time you press a button, enable and disable change. When you come out of the set-up mode press the MENU button. $-2 BAUD RATE SETUP Move CURSOR(→) to the Baud rate you want, and press the ENTER button.
SSC-1000 (gb) 2009.1.8 1:38 PM Page 16 User’s Guide * DATA BACK-UP In case changing the camera by downloading the set-up data of the Samsung Dome Camera, this is a function for applying the set-up value set up in the changed camera just the way it is. In order to perform this mode, move CURSOR(→) to the DATA BACK-UP in the CAMERA SET MENU, and press the ENTER button. If you want to go back to the main menu, press the MENU button.
SSC-1000 (gb) 2009.1.8 1:38 PM Page 18 User’s Guide 3) Manipulating the RECEIVER UNIT ! For receiver unit manipulation, as only those applying to the cam no. indicated in the LCD are possible, first select the camera you wan to manipulate. For camera selection, when you press CAM + NO. + ENTER, the concerned camera number gets indicated in the LCD. (The camera number is the address number of the receiver unit) @ In the third line of the LCD, the camera's action state gets indicated.
SSC-1000 (gb) 2009.1.8 1:38 PM Page 20 User’s Guide # TOUR action This is a function for putting out the Tour Switching program set up in the matrix switcher on the monitor of your discretion. First, select the monitor you intend to put out, and when you press TOUR+NO.+ENTER, the visuals corresponded to the pertinent Tour program get automatically converted, “TOUR [NO] RUN” get indicated in the LCD.
SSC-1000 (gb) 2009.1.8 1:38 PM Page 22 User’s Guide 5. Confirmation Matter in Times of Abnormality Occurrence 6. Specifications ITEM Symptom Confirmation and Management Matters Control of the camera part is not possible. 1. Check the polarity of the RS-485 indication line. 2. Check if the address of the camera part has been set up well. The input channel number of the Matrix Switcher and the number of the camera part appear differently.