SCC-B5397 SCC-B5331 SCC-B5399 SCC-B5333 SCC-B5335 RUS user manual ENG ENG DIGITAL COLOR DOME CAMERA POL CZE Thank you for purchasing this Samsung product. To receive more complete service, please register your product at www.samsungsecurity.
Safety information 1. CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 2. 3. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.
S er 1. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fire or electric shock. 2. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair.) 3.
Safety information WARNING 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat. 9.
nd ve or Introduction Features Product & Accessories Part Names and Functions 6 7 8 Installation Before installation Installation procedure Adjusting the camera direction 11 11 12 ENG e Contents How to use OSD Menu Using Icons in the Menu Main Menu Profile Camera Setup Intelligence Privacy Zone Setup Other Set System Information Language 14 14 15 17 24 27 28 29 29 Specifications Specifications 30 English – 5
Introduction FEATURES ❖ High Resolution • This camera has realized high resolution of 600 lines using the top-notch full digital image processing and special algorithm technologies. ❖ VPS(Virtual Progressive Scan) • This is an advanced technology that reproduces a sharp progressive image. This is appropriate to high quality recording and file transfer via the Internet. ❖ Intelligent Motion Detection & Tracking • This is an intelligent function that automatically detects a motion of an object.
Introduction Components Checking components in the package Camera Test Monitor Cable User’s Guide f ENG e Image f s Part name Standard Quantity Usage Plastic anchor HUD 5 4 (EA) Attach each piece to screw connection holes for strengthening connection ASSY screw machine BH M5 X L6.
Introduction 1.Dome cover: Covers the inner cover, lens, and Components of your camera Your camera has the following components: main body to protect them. ❖ 2.Cover screw: Use it to assemble or disassemble both dome cover and case. 1 3.Inner cover: Covers the main body to protect it. 4.Wing locker: Push a long thin screwdriver into 3 2 4 5 7 6 6 7 8 its narrow spot and press it outward when you want to remove the inner cover. 5.
Introduction ❖ Setting switches ENG • SETUP Switch This switch is used to set the function or property. When this switch is pressed for at least 2 seconds, the MAIN MENU appears. ef (Left/Right) : By pressing this switch left or right, you can move left or right on the menu or change the displayed value. cd (Up/Down) : By pressing this switch up or down, you can move up or down on the menu. : When you press this switch in the menu, the selected function is confirmed. To enter a submenu, press this button.
Installation I Installing camera Before installation Before installing your camera, you have to read the following cautions: You have to check whether the location (ceiling or wall) can bear five times the weight of your camera. Don’t let the cable to be caught in improper place or the electric line cover to be damaged. Otherwise it may cause a breakdown or fire. You can use wall mount adaptor (SADT-102WM), and pole mount adaptor (SADT100PM) for installing the camera on the wall or pipeline.
n Installation Installing on a pipe Before installation, you have to be familiar with the above cautions and fill in the holes that are not used for installation. To install your camera bottom on a pipe 1. After connecting the power and video cables, throw them inside the pipeline and screw the male thread pipe into the female pipe thread in your camera tightly to fix the Main body. (In this case, be sure to tape with Teflon tape before assembly for waterproofing.
Installation H Adjusting the camera direction When the camera is fixed on the ceiling, you can adjust the camera viewing angle. You can rotate your camera leftward or rightward (Panning), and can change the slope of your camera upward or downward (Tilting). In case of panning, the rotation limit of your camera is set to 355 degree (100 degree clockwise and 255 degree counterclockwise). The rotation is stopped by the Stopper inside of the camera.
e. e 0 by ws to e. e g USING ICONS IN THE MENU • (EXIT) Exits the menu setting. Before you exits the menu setting, select SAVE to save your settings, or select QUIT to cancel. • (RET) Returns to the previous menu. MAIN MENU MAIN MENU PROFILE CAMERA SET INTELLIGENCE PRIVACY ZONE OTHER SET SYSTEM INFO LANGUAGE • (HOME) Returns to the main menu. • (SAVE) Used to save your settings of MASK AREA, PRIVACY ZONE and more.
How to use OSD Menu PROFILE ePROFILEf STANDARD ITS BACKLIGHT DAY/NIGHT GAMING CUSTOM D W In the PROFILE menu, you can configure the following camera settings at once. CAMERA SET Menu Previous Sub-menus Menu VPS IRIS ALC LENS LEVEL BACKLIGHT WDR WEIGHT WDR LEVEL WHITE BAL MOTION DNR STANDARD ITS BACKLIGHT DAY/NIGHT GAMING OFF ALC DC 0 OFF User setting allowed User setting allowed User setting allowed (F.
How to use OSD Menu BRIGHTNESS MODE RED BLUE DETAIL STANDARD ITS BACKLIGHT DAY/NIGHT GAMING OFF AUTOx4 MID AUTO OFF DAY ATW2 0 0 User setting allowed OFF User setting allowed User setting allowed 2 AUTO1/250 AUTOx2 MID AUTO ON DAY/NIGHT ATW1 0 0 - OFF AUTOx4 MID DAY OFF DAY ATW1 0 0 User setting allowed OFF User setting allowed User setting allowed 2 OFF AUTOx4 MID AUTO OFF DAY/NIGHT ATW1 0 0 - OFF AUTOx4 MID DAY OFF DAY ATW1 0 0 User setting allowed OFF User setting allowed User setting allowed
How to use OSD Menu Setup the general functions of zoom camera module. CAMERA SETUP Use the cdef switch to select a menu item. eCAMERA SETf CAMERA ID OFF VPS OFF IRIS ALC MOTION (F.FAST)--DNR MID SHUTTER OFF SENS-UP AUTO X4 FLICKERLESS (OFF)--XDR MID d ❖ CAMERA ID CAMERA ID ABCDEFGHIJKLMNOPQRSTUVWXYZ0 123456789 :?-+*()/ SPffeeSP LOCATION CAMERA-1.................. ...........................
e. • ALC (Automatic Light Control) ① If you press the SETUP switch with an ALCbased sub menu selected, you will see the appropriate screen. ALC LEVEL BACKLIGHT [00]----I---OFF If you use an ordinary camera in a scene with an intensive backlight, the object will be displayed dark on the monitor affected by the backlight. To solve this problem, you can use the BLC(Back Light Compensation) function to improve the sharpness of the image in such a high contrast scene.
How to use OSD Menu ❖ AGC [OFF, VERY LOW, LOW, MID, HIGH, VERY HIGH, USER, FIX] The AGC (Auto Gain Control) menu is used to set the AGC level of the camera. When the AGC is active, the camera automatically increases the sensitivity by amplifying the Video signal when the strength of the signal falls below the normal value. If OFF or FIX mode is selected in the SENS-UP menu, you can specify the AGC level. If you press the SETUP switch with a USER sub menu selected, you will see the appropriate screen.
n. d. ST] n. M, st Note : – If the DAY/NIGHT menu of the CAMERA SET is set to AUTO, the MOTION menu will be deactivated. ❖ DNR [OFF,LOW,MID,HIGH, USER(1~16)] You can configure the DNR (Digital Noise Reduction) related settings. Reduces the noise on the screen. This is especially useful for a severely distorted screen. You can set the level if you set DNR to USER.
How to use OSD Menu ❖ FLICKERLESS [OFF, ON] If set to ON, the shutter speed will be fixed to 1/100(PAL:1/120) second. This will prevent possible screen distortion due to a mismatch between the vertical sync frequency and the blinking frequency of the lighting. Note : – If the SHUTTER menu is set to AUTO or FIX mode, the FLICKERLESS menu will not be available. – If the SENS-UP function is set to FIX mode, the Flickerless menu will be deactivated.
es e. HIGH. As you adjust it from HIGH to LOW, the screen switches to black and white mode under the darker situation. DWELL TIME of DAYÆNIGHT sets the time to maintain switched black and white mode. The BRIGHTNESS of NIGHTÆDAY sets the brightness degree of BW to color switching, for which you can select from LOW, MID, and HIGH. As you adjust it from HIGH to LOW, the screen switches to color mode under the darker situation. DWELL TIME of NIGHTÆDAY sets the time to maintain switched color mode.
How to use OSD Menu • NIGHT Use the NIGHT mode if you want to set the white balance differently according to the ambient luminance. If the NIGHT mode is set to OFF, the white balance will always operate as set in DAY mode; if not to OFF, the camera will switch to as set in DAY/NIGHT mode according to the brightness. In NIGHT mode, you can set the values of RED, BLUE and BRIGHTNESS. The screen will be displayed in colors according to your settings.
How to use OSD Menu e Note : DIGITAL ZOOM – Use of DC 12V will fix V-SYNC to INT, which can not be RATIO [X1.0] < LOCATION > changed. ❖ AGC COLOR SUP ❖ REVERSE Note : – If the digital zoom factor is set to larger than 1x, the FENCE function will be deactivated. The DIGITAL ZOOM function enlarges the pixel itself, which can cause deterioration of the quality. ❖ DETAIL [0~3] Controls the horizontal or vertical distinction.
How to use OSD Menu • FENCE INTELLIGENCE eINTELLIGENCEf MOTION ADVANCED MASK AREA DISPLAY SENSITIVITY RESOLUTION 1 OFF OFF 2 3 4 ON [4] [5] This is to detect if a moving object passes through the specified LINE or AREA.
or How to use OSD Menu ① If you press the SETUP switch with the LINE option set to ON, you can specify the position and detection direction of the line. ② If you change the PIXEL LEVEL for setting the position, specify the pixel that moves by a single pressure of the cdef switch. ④ If you change the DIRECTION, you can specify the detection direction. The detection direction based on the defined two points will be displayed on the screen.
How to use OSD Menu - a fixed object moves in one position continuously - a second object screens the first moving object PRIVACY ZONE SETUP Us PR ePRIVACY ZONEf ❖ MASK AREA [1~4] Specify a detection exception area to mask. Select a mask number and specify the size and position. 1 7 2 8 3 9 4 10 PRIVACY SET STYLE 5 11 6 12 ON MOSAIC1 MASK AREA ❖ DISPLAY [1~7] Set the sensitivity of the motion detection.
How to use OSD Menu Use the cdef switch to select one from PRIVACY 1 through 12. Select one from PRIVACY 1~12 and press the SETUP switch to confirm your setting. You can specify a pixel that moves as you change the PIXEL LEVEL to set the position. ② Use the cdef switch to move the position and press the SETUP switch to confirm it. Note : – If more than one PRIVACY ZONE is specified and the PRIVACY SET is set to ON, the PIP function will be deactivated.
How to use OSD Menu ❖ SYSTEM INFORMATION EXTERNAL TRG STILL TIME DELAY TIME OFF FIX eSYSTEM INFOf TYPE 3_VAR_WDR_P SERIAL NO. 000000000000000 CAMERA VER. 0.50_090101 You can set the STILL TIME to 0~4 seconds. If DELAY TIME is set to FIX, the DELAY TIME will be set in sync with the STILL TIME; if set to USER, the DELAY TIME will be set to your setting. Note : – If VPS is set to OFF, the EXTERNAL TRG menu will be deactivated.
How to use OSD Menu ❖ Initial Configuration Table • Camera Configuration CAMERA ID OFF VPS OFF IRIS ALC AGC VERY HIGH MOTION DNR (F.
Specifications SPECIFICATIONS Items Camera Type Image Scanning Sub-items Horizontal Frequency Vertical Frequency Min. Scene Illumination Functions SCC-B5397N/SCC-5399N CCTV Camera (WDR & DAY/NIGHT) Device 1/3” Super-HAD PS CCD Total 811 x 508 Pixels Effective 768 x 494 System Interlace/Progressive Scanning Line 525 lines Frame 30frame/1sec Internal Mode 15,734 Hz Line-lock Mode Internal Mode Line-lock Mode 15,750 Hz 59.94 Hz 60 Hz Sens-up OFF OFF OFF 512 times 512 times 512 times Condition F No.
Specifications s Items SCC-B5397N/SCC-5399N Video Output S/N Ratio Sens-Up AGC Line Lock Camera ID White Balance Digital Noise Reduction(DNR) Digital Image Stabilization(DIS) Intelligent Video Etc. Function Horizontal Vertical S/N Ratio x2 ~ x512 Off/On (Max.Level Setting) Off/On (Phase Control) Off/On (Max.54ea/2Line) ATW1/ATW2/AWC/3200K/5600K Off/On (Adaptive 3D+2D) Off/On Fixed/Moved, Fence Detail, Reverse(H/V), Posi/Nega 600 TV Lines 350 TV Lines VBS 1.0Vp-p, 75 Ω Approx.
Specifications Items Camera Type Image Scanning Sub-items Horizontal Frequency Vertical Frequency Min. Scene Illumination Functions SCC-B5397P/SCC-5399P CCTV Camera (WDR & DAY/NIGHT) Device 1/3” Super-HAD PS CCD Total 795 x 596 Pixels Effective 752 x 582 System Interlace/Progressive Scanning Line 625 lines Frame 25frame/1sec Internal Mode 15,625 Hz Line-lock Mode Internal Mode Line-lock Mode 15,625 Hz 50 Hz 50 Hz Sens-up OFF OFF OFF 512 times 512 times 512 times Condition F No. 1.2 1.2 1.2 1.2 1.
Specifications Items SCC-B5397P/SCC-5399P Video Output S/N Ratio AGC Line Lock Camera ID White Balance Digital Noise Reduction(DNR) Digital Image Stabilization(DIS) Intelligent Video Etc. Function Horizontal Vertical S/N Ratio Off/On (Max.Level Setting) Off/On (Phase Control) Off/On (Max.54ea/2Line) ATW1/ATW2/AWC/3200K/5600K Off/On (Adaptive 3D+2D) Off/On Fixed/Moved, Fence Detail, Reverse(H/V), Posi/Nega 600 TV Lines 350 TV Lines VBS 1.0Vp-p, 75 Ω Approx.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.
