NETWORK CAMERA User Manual SNB-6005
Network Camera User Manual Copyright ©2015 Hanwha Techwin Co., Ltd. All rights reserved. Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
overview Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. ● overview 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
overview WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT. Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance with the installation instructions.
Class construction An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection. Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. Disconnection Device Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location. When used outside of the U.S., it may be used HAR code with fittings of an approved agency is employed.
overview Please read the following recommended safety precautions carefully. yy Do not place this apparatus on an uneven surface. yy Do not install on a surface where it is exposed to direct sunlight, near heating equipment or heavy cold area. yy Do not place this apparatus near conductive material. yy Do not attempt to service this apparatus yourself. yy Do not place a glass of water on the product. yy Do not install near any magnetic sources. yy Do not block any ventilation openings.
CONTENTS overview 11 12 13 installation & connection 16 network connection and setup 27 16 18 19 20 27 28 29 30 31 32 36 37 39 39 Important Safety Instructions Product Features Recommended PC Specifications Recommended Micro SD/ SDHC/SDXC Memory Card Specifications NAS recommended specs What’s Included At a Glance Mounting the Lens Inserting/Removing a Micro SD Memory Card Memory Card Information (Not Included) Connecting with other Device Connecting the Camera Directly to Local Area Networking Conn
overview web viewer 40 42 42 43 45 49 Connecting to the Camera Password setting Login Installing STW WebViewer Plugin Using the Live Screen Playing the recorded video setup screen 56 56 67 84 93 99 117 123 Setup Basic Setup Video & Audio setup Network Setup Event Setup NAS (Network Attached Storage) guide System Setup Viewing profile information 124 129 130 132 Specification Product Overview Troubleshooting Open Source Announcement 40 56 appendix 124 8_ overview
Product Features English _9 ● overview •• Full HD Video Quality •• Multi-Streaming This network camera can display videos in different resolutions and qualities simultaneously using different CODECs. •• Web Browser-based Monitoring Using the Internet web browser to display the image in a local network environment.
overview Recommended PC Specifications •• CPU : Intel Core 2 Duo 2.4 GHz or higher (for using 1920x1080 30 fps) Intel Core i7 2.8 GHz or higher (for using 1920x1080 60 fps) `` Web Plug-in is optimized to SSE 4.1 Instruction Set. •• Resolution : 1280X1024 pixels or higher (32 bit color) •• RAM : 2GB or higher •• Supported OS : Windows XP / VISTA / 7 / 8 / 8.1, MAC OS X 10.7 •• Supported Browser : Microsoft Internet Explorer (Ver. 11 ~ 8) Mozilla Firefox (Ver. 19 ~ 9) ※ Windows Only Google Chrome (Ver.
Recommended Micro SD/SDHC/SDXC Memory Card Specifications NAS recommended specs •• Recommended capacity : 200GB or higher is recommended. •• Simultaneous access : One unit of NAS can accept a maximum of sixteen camera accesses. •• For this camera, you are recommended to use a NAS with the following manufacturer’s specs. Recommended products Netgear NAS Synology NAS Available sizes A maximum of 16 cameras can access simultaneously. A maximum of 16 cameras can access simultaneously.
overview What’s Included Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.
At a Glance Front Side ● overview a b Item Description a Mounting Bracket Screw Hole Used to fix the camera on a mounting bracket. `` The screw size : It is the specification for the screws used to fasten the camera to the support. 1/4" - 20 UNC L : 4.5mm±0.2mm (ISO Standard) or 0.197" (ASA Standard) b Auto Iris Lens Connector Used to supply power and output signal to control the iris of the lens.
overview Rear Side a b j i c d e h f g Item a Micro SD Memory Card Compartment b Audio terminal Description Compartment for the Micro SD memory card. AUDIO OUT Used to connect to speakers. AUDIO IN Used to connect to a microphone. The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.
Item Description Lightning protective grounding port Used to discharge the lightning current safely outside in order to protect the camera. f Power Port Used to plug the power cable. g Network Port Used to connect the PoE or Ethernet cable for network connection. h i Alarm I/O Port Test Monitor Out ALARM IN Used to connect the alarm input sensor or external day/ night sensor. ALARM OUT Used to connect the alarm output signal. GND Used for earth-grounding.
installation & connection Mounting the Lens Disconnect the power before proceeding. C/CS lens and C-mount adaptor are not included in the product package. MM `` The It is recommended that megapixel lens are use on this camera to optimise performance. Mounting the CS lens on a camera Turn the CS lens clockwise to attach it. CS Lens Mounting the C lens on a camera Turn the C mount adapter clockwise and turn the C lens clockwise.
Connecting the Auto Iris Lens connector Plug the iris connector of the lens in the camera connecting groove. Select a target to film, turn the zoom lever of the lens to adjust the magnification and then focus the lens so that target is clearly displayed. focusing with the zoom lever of the lens, press the [FOCUS] button on the rear of the camera MM `` After to adjust the lens even more clearly.
installation & connection Inserting/Removing a Micro SD Memory Card JJ `` Disconnect the power cable from the camera before inserting the Micro SD memory card. `` Do not insert the Micro SD memory card while it’s upside down by force. Otherwise, it may damage the Micro SD memory card. Inserting a Micro SD Memory Card Push the Micro SD memory card in the direction of the arrow shown in the diagram.
Memory Card Information (Not Included) What is a memory card? Selecting a memory card that’s suitable for you Your camera supports Micro SD/SDHC/SDXC memory cards. You may, however, experience compatibility issues depending on the model and make of the memory card. For your camera, we recommend you use a memory card from the following manufacturers: Micro SD/SDHC/SDXC Memory Card : Sandisk, Transcend Memory cards of 4GB ~ 64GB is recommended for using with this camera.
installation & connection Connecting with other Device Monitor to install Grounding cable Power Ethernet CVBS out terminal of the product is provided for easier installation, and is not recommended JJ `` The for monitoring purposes. Ethernet Connection Connect the Ethernet cable to the local network or to the Internet.
Power Supply Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the camera. -- You can also use a router featuring PoE to supply power to the camera. -- Use PoE that is compliant with the IEEE802.3af protocols. `` Be careful not to reverse the polarity when you connect the power cable. `` AC24 can be connected in non-polar union. `` If you want to connect an external device, you must turn off the external device before proceeding.
installation & connection Network Cable Specification Item Connector Ethernet Cable Max Distance PoE Support Contents RJ45 10/100Base-T UTP Category 5e 100M IEEE 802.3af Remark 10/100 Mbps Grounding the Product Connect the ground wire to the ground terminal which is located above the power input terminal by using a screwdriver. JJ `` Grounding protects the product from a surge or lightning. `` When grounding, make sure to turn the product’s power off.
Connecting to Audio Input/Output Speaker Amp Microphone Speaker ● installation & connection Microphone PC Microphone Network Amp Speaker 1. Connect the AUDIO IN port of the camera with the microphone or LINE OUT port of the amplifier that the microphone is connected to. MM `` As a microphone is built in, you can use the built-in microphone instead of an external one. 2. Connect the AUDIO OUT port of the camera with the speaker or LINE IN port of the amplifier that the speaker is connected to.
installation & connection 3. Check the specifications for audio input. •• Audio Codec -- Audio In : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz), G.726 ADPCM (Bit Rate: 16Kbps, 24Kbps, 32Kbps, 40Kbps / Sampling Frequency: 8kHz) -- Audio Out : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz) •• Full duplex Audio •• Audio in : Mono signal line input (Max.2.4 Vpp) •• Audio out : Mono signal line output (Max.2.
Connecting an external RS-485 device Connect the camera with an external device using the [RS-485 +, -] ports. You can control the pan/tilt operations of the camera via RS-485 communications. failure, connect the GND pin as appropriate to correct the GND level between camera and external device. To connect the external sensor Connect one strand of each signal line (2-strand) of the sensors to the [ALARM IN] port, and connect the other strand to the [GND] port.
installation & connection To connect the alarm out If devices (e.g., flashing light and siren) that exceed the voltage and current specifications are connected by using the open collector method, it may cause malfunction. Refer to the alarm out connection diagram below when connecting devices that exceed the voltage and current specifications. Alarm Out Wiring Diagram Inside of the camera DC 5V or 3.
network connection and setup You can set up the network settings according to your network configurations. Connecting to the camera from a local PC in the LAN 1. Launch an Internet browser on the local PC. 2. Enter the IP address of the camera in the address bar of the browser.
network connection and setup Connecting the Camera Directly to a DHCP Based DSL/Cable Modem Camera DSL/Cable Modem INTERNET External Remote PC DDNS Server (Data Center, KOREA) 1. Connect the user PC directly with the network camera. 2. Run the IP Installer and change the IP address of the camera so that you can use the web browser on your desktop to connect to the Internet. 3. Use the Internet browser to connect to the web viewer. 4. Move to [Setup] page. 5.
Connecting the Camera Directly to a PPPoE Modem PPPoE Modem INTERNET External Remote PC DDNS Server (Data Center, KOREA) 1. Connect the user PC directly with the network camera. 2. Run the IP Installer and change the IP address of the camera so that you can use the web browser on your desktop to connect to the Internet. 3. Use the Internet browser to connect to the web viewer. 4. Move to [Setup] page. 5. Move to [Network] – [DDNS] and configure the DDNS settings. 6.
network connection and setup Connecting the Camera to a Broadband Router with the PPPoE/Cable Modem This is for a small network environment such as homes, SOHO and ordinary shops.
Buttons used in IP Installer a b c d e f g ● network connection and setup hi Item j k l m Description a Device Name Model name of the connected camera. Click the column to sort the list by model name. However, search will be stopped if clicked during the search. b Alias This function is not currently implemented. c Mode Displays either , or for the current network connection status.
network connection and setup Item Description g URL DDNS URL address enabling access from the external Internet. However, this will be replaced with the of the camera if DDNS registration has failed. h IPv4 Scans for cameras with the IPv4 setting. i IPv6 Scans for cameras with the IPv6 setting. Activated in an IPv6 compliant environment only. j Search Scans for cameras that are currently connected to the network.
related parameters can be set only MM `` IPwhen DHCP is not checked. If not using a Broadband Router For setting , , and , contact your network administrator. 4. In the pane, provide necessary information. •• HTTP Port : Used to access the camera using the Internet browser, defaulted to 80. •• VNP Port : Used to control the video signal transfer, defaulted to 4520. 5. Enter the password. Enter the password of “admin” account, which was used to access the camera.
network connection and setup If using a Broadband Router •• IP Address : Enter an address falling in the IP range provided by the Broadband Router. ex) 192.168.1.2~254, 192.168.0.2~254, 192.168.XXX.2~254 •• Subnet Mask : The of the Broadband Router will be the of the camera. •• Gateway : The of the Broadband Router will be the of the camera. settings may differ depending on the connected Broadband Router model.
Auto Network Setup Run to display the camera search list. At the initial startup, both [Auto Set] and [Manual Set] will be grayed out. 1. Select a camera in the search list. Check the MAC address of the camera on the camera’s label. Both the [Auto Set] and [Manual Set] buttons will be activated. 2. Click [Auto Set]. The Auto Setting dialog appears. The , , and will be set automatically. 3. Enter the password.
network connection and setup Dynamic IP Setup Dynamic IP Environment Setup •• Example of the Dynamic IP environment -- If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server -- If connecting the camera directly to modem using the DHCP protocols -- If IPs are assigned by the internal DHCP server via the LAN Checking the Dynamic IP 1. Run the IP Installer on the user’s local computer. Cameras allocated with address are shown in the list. 2.
Port Range Forward (Port Mapping) Setup If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the Broadband Router so that a remote PC can access the camera in it. ● network connection and setup Manual Port Range Forwarding 1. From the Setup menu of the Broadband Router, select - . For setting the port range forward for a third-party Broadband Router, refer to the user guide of that Broadband Router. 2.
network connection and setup Setting up Port Range Forward for several network cameras •• You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page. •• A user can change each port using the camera setting screen. When Camera1 and Camera2 are connected to a router : User Internet Start 3000 3001 4520 4521 8080 8081 Broadband Router End Protocol 3000 TCP/UDP 3001 TCP/UDP 4520 TCP/UDP 4521 TCP/UDP 8080 TCP/UDP 8081 TCP/UDP IP Address 192.168.1.100 192.
Connecting to the Camera from a Shared Local PC 2. Double-click a camera to access. The Internet browser starts and connects to the camera. to the camera can also be gained by typing the camera's IP address in the address bar of MM `` Access the Internet browser.
web viewer Connecting to the Camera Normally, you would 1. Launch the Internet browser. 2. Type the IP address of the camera in the address bar. ex) • IP address (IPv4) : 192.168.1.100 http://192.168.1.100 - the Login dialog should appear. • IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111 http://[2001:230:abcd:ffff:0000 :0000:ffff:1111] - the Login dialog should appear. If the HTTP port is other than 80 1. Launch the Internet browser. 2.
Connecting via UPnP 1. Run the client or operating system in support of the UPnP protocol. Connecting via Bonjour 1. Run the client or operating system in support of the Bonjour protocol. 2. Click the camera name for search. In the Mac operating system, click the camera name searched from the Bonjour tab of Safari. -- The login window is displayed.
web viewer Password setting When you access the product for the first time, you must register the login password. When the “Password change” window appears, enter the new password. a new password with 8 to 9 digits, JJ `` For you must use at least 3 of the following: uppercase/lowercase letters, numbers and special characters. For a password with 10 to 15 digits, you must use at least 2 types of those mentioned. -- Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].
Installing STW WebViewer Plugin If connecting to a camera for the first time, you will see the installation message. Then, install the required WebViewer Plugin to access the camera and control the video from it in real time. the plug-in installation file download status is suspended at 99% in the Internet Explorer JJ `` Ifbrowser, retry it after selecting “Release SmartScreen filter” in “Tool SmartScreen filter”. 2. Click [Run] in the message window. 3.
web viewer 5. Click [OK]. The old version of Web Viewer Plug-in is deleted. 6. Click [Install] to begin installation of the Web Viewer Plug-in. 7. Click [Finish]. STW Web Viewer Plug-in installation is completed. internet explorer, if you need JJ `` Into your move to the installation screen after installing the STW webviewer plugin, check whether webviewer_ activexplugin_lib.control in the “Tool Additional Function Management” menu is “Activated”.
Using the Live Screen a b c d e ● web viewer f g h i j k l m n o Item Description a Monitoring Move to the monitoring screen. b Playback Move to the screen where you can search for the video recording saved in your Micro SD memory card or NAS. c Setup Move to the Setup screen. d Profile access information e Viewer Screen You can read the profile information. Displays the Live video on the screen. `` You can use the mouse wheel to activate the digital zooming in Viewer screen.
web viewer Item Description You can select a profile type in
To capture the snapshot 1. Click [Capture ( )] on the scene to capture. encounter an interrupted video when capturing the image with IE8 on a Windows 7-based MM `` IfPC,youdeselect “Turn On Protected Mode” from “Tools – Internet Options – Security”. `` If the screen is not captured by IE browser in Windows 7 or 8, run the IE Browser with the Admin privilege. How to record videos manually 1. Press [Manual recording ( )]. 2. To end the recording, press [Manual recording ( )] again.
web viewer To Use Audio 1. Click [Audio ( 2. Use [ )] icon to activate audio communication. ] bar to control the volume. there is no sound from pulling in and out the audio jack while it is in operation, click the MM `` If[Audio ( )] icon to enable it again. To Use Microphone Click [Mic ( )] icon to activate the microphone. To control the PTZ 1. Press the [PTZ ( )] tab. 2.
Playing the recorded video you can play the video, you must configure the record settings. For details on record settings, MM `` Before refer to “Storage”. (page 95) ● web viewer Name of event search screen and its function a b c Item Description a Set the search date and time range for data saved in your Micro SD memory Search range setting card or NAS. b Search event setting Set the event type to search within the search period. c Event search Run the event search.
web viewer To play the content after searching by event 1. Click the [Playback ( )] button. 2. Specify the start time and end time of your search. 3. Select an event type for your search within the specified period. 4. Click the [Event search] button. The search results will be displayed in the list. more than 800 events are recorded MM `` Ifwithin the search period, your search will be limited up to the date when the 800th event is recorded.
Name of time search screen and its function ● web viewer b c d e f g h i a Item Description a Time bar The section in the specific period is played by moving the time bar. b Search date setting `` If there is data saved in your Micro SD memory card or NAS on the c Speaker To listen to a voice signal (if present) in the recorded video, then activate the voice signal icon when you play it. d Screen optimization The camera image is converted to fit the Web browser window.
web viewer Item h Video information i Backup Description Time data of the replayed video is displayed on the screen. Set the desired date to make a backup copy of video data saved in your Micro SD memory card or NAS. `` It can be set as up to 5 minutes for Micro SD memory card or up to 30 minutes for NAS. To play after searching by time 1. Click [Time Search ( )]. 2. Click a desired date in the calendar. The video on the specified date will be played. 3.
6. Move [Time bar ( )] to a desired time point of the video before playing it. The time containing a normal recoding file will be highlighted in blue; the time with the event recording will be highlighted in red. ● web viewer To back up the searched video 1. During playback, click [ ] on the scene to back up. The scheduling window for backup start and end time appears. ] button. 2. Click [ The Save As window appears. 3. Confirm the save path and click [Save] button.
web viewer To Play an AVI File (1) Micro SD memory card 1. Separate the Micro SD memory card from the camera. separating the Micro SD memory card, set the to in the “Setup JJ `` Before Event Storage” menu. 2. Insert the Micro SD memory card into the PC. 3. Play the AVI file in the “\ch00\img\ YYYY_mm_DD\AVI” directory, using a media player. filename starts with the format “001_ MM `` AYYYYMMDD_HHMMSS.avi” and the file number is incremented by one.
(2) NAS (Network-Attached Storage) ● web viewer 1. In Windows browser, use \\\ to access. ex)\\192.168.20.31\defaultfolder\ch01\ img\2013_07_02\AVI 2. Go to Enter 1. 3. Connected to the NAS. The directory structure is same as the directory structure for a Micro SD memory card. filename starts with the format “001_ MM `` AYYYYMMDD_HHMMSS.avi” and the file number is incremented by one. YYYYMMDD_HHMMSS indicates the start time of data saving.
setup screen Setup On the network, you can set up basic information on the camera, video and audio, network events and system. 1. In the Live screen, click [Setup ( 2. The Setup screen appears. )]. setting page for preview video requires the STW web viewer plug-in to be installed on the PC. JJ `` The If it is not intalled properly, the installation page automatically apprears. Basic Setup Video profile 1. From the Setup menu, select the tab. 2. Click
4. Select each profile properties. For more details, refer to “To Add/Change the Video Profile”. (Page 59) 5. Click the input box of each item and enter / select a desired value. `` The context menu may differ depending on the selected codec type. •• Record profile : This is the profile that is applied to video recording. •• Audio-In : Sets whether to use audio for video recordings. 6. According to your situation, set ATC (Auto Transmit Control) mode.
setup screen •• ATC sensitivity : Affect the transfer rate according to the variance in the network bandwidth. The transfer rate will be adjusted to the fastest if the bandwidth is , and adjusted to the latest if the bandwidth is . •• ATC limit : If the quality or frame rate is adjusted, the property will be changed to the applied value (%) against the previous setting value (100%). Note that if you reduce the property value too much, you may encounter flickering on the screen.
To Add/Change the Video Profile The profile setup can be added or modified to accommodate various profiles depending on the recording conditions. 2. Provide the name and select a codec. 3. Specify the conditions under which the codec will be applied. 4. Specify the details of the selected codec including resolution and frame rate. Click to display the context menu. •• Resolution : Set the video size of the H.264 and MJPEG files. •• Framerate : Set the max number of video frames per sec.
setup screen •• Encoding priority : You can set the priority of video transmission to frame rate or compression. •• GOV length : It specifies the distance (in terms of number of frames) between two consecutive I-Frames in a video sequence when H.264 codec was selected. (One I-Frame + 0~Several P-Frames) •• Profile : You can select the H.264 profiling method. •• Entropy coding : Reduce the possible compression loss due to encoding. •• Smart codec : Specify the use of Smart codec.
To Use Crop Encoding 1. Select
setup screen User 1. From the Setup menu, select the tab. 2. Click . 3. Provide the necessary user information. •• Administrator password change : Change the password for the administrator. the security purposes, you are JJ `` For recommended to use a combination of numbers, alphabets uppercase and lowercase and special characters for your password. `` It is recommended to change your password once every three months. `` The password length and limits are shown as follows.
-- If the existing password is not matched, when you change the admin password, you cannot change the password. -- After changing your password, if there is a camera connected to a CMS or NVR client, `` When the password is changed while multiple connections are active from a PC, the browser may malfunction. In that case, reconnect to the server. •• Guest setup : If you select , the guest account can access the Web viewer screen but can only view the live Viewer screen.
setup screen Date & Time 1. From the Setup menu, select the tab. 2. Click . 3. Specify the time and date that will be applied to the camera. •• Current system time : Displays the current time settings of your system. •• Timezone : Specify the local time zone based on the GMT. •• Use daylight saving time : If checked, the time will be set one hour before the local time zone for the specified time period. This option will be displayed only in areas where DST is applied.
IP & Port 1. From the Setup menu, select the tab. 2. Click . ● setup screen 3. Set the . •• IP type : Select an IP connection type. -- Manual : Specify the IP address, Subnet mask, Gateway, DNS1, and DNS2. -- DHCP : Specify the DNS1 and DNS2. -- PPPoE : Specify the DNS1, DNS2, ID and Password. `` If you set it to , you should specify the IP, Subnet mask, Gateway, DNS 1 & 2 manually. •• MAC address : Shows the MAC address.
setup screen 5. Type in each item in the Port menu as necessary. `` Neither the port range between 0 and 1023 nor port 3702 is available. •• HTTP : HTTP port used to access the camera via the web browser. The default is 80(TCP). `` Setting the HTTP port for Safari and Google Chrome browsers to 65535 is not allowed by security policy. •• HTTPS : In this version, the security of the web communication protocol HTTP is strengthened. It can be used when you set HTTPS mode in SSL.
Video & Audio setup Video setup ● setup screen 1. From the Setup menu, select the
setup screen Audio setup You can configure the I/O settings of the audio source from the camera. 1. From the Setup menu, select the
Camera setup You can change the camera settings according to the environment where the camera is located. ● setup screen 1. From the Setup menu, select the
setup screen •• Reduced noise : Select this when you need a video with low noise in the low illumination environment. •• Bright video : This makes the dark area in a full video brighter. JJ `` Video contracts effects are reduced. •• Motion focus&Reduced noise : Use this when there are many moving objects, such as on a road or in a crowded place like a museum, or when you need a video with low noise in a low illumination environment.
Initial setting for each image preset mode SSDR SSNR3 Default (1/5) 1/12000 Default (High) Default (12) Default (12) Reduced noise 1/15 1/12000 Default (High) Default (1/5) Motion focus Bright video Motion focus&Reduced noise Motion focus&Bright video User preset 1/30 Default (12) 4 1/12000 Middle Default Default (12) Default (12) 1/30 1/12000 Middle Default (12) 4 1/30 1/12000 Manual 1/12000 Manual Default Manual 18 18 Manual Default (12) 4 Manual preset setup func
setup screen To Set the Sensor It specifies how many frames the camera CMOS sensor will capture per second. 1. Select . 2. Select . to “Video profile” for the framerate setup range of the
To Set White Balance You can correct the image colors based on white under any lighting conditions. 1. Select . AWC mode, click the [Set] button if you want to keep the white balance level of the current MM `` Inimage. white balancing may not work properly in the following conditions: JJ `` The If this is the case, switch to AWC mode.
setup screen To Set BLC You can specify a desired area on the video manually and set the area to be displayed more clearly. 1. Select . 2. Set to . 3. Set . You can change the level to adjust the brightness of the monitoring area. 4. Set the levels to specify the target area. JJ `` When BLC is set, the green box is displayed on the screen for 15 seconds.
To Set Exposure You can adjust the exposure level of the camera. 1. Select . `` The framerate may be reduced in the dark condition if Shutter has a lower value than specified in the Sensor mode. •• Maximum shutter : The limit of the shortest exposure time. •• Anti flicker : It prevents screen flickering incurring from the dissonance between the surrounding lighting and the frequency. •• SSNR3 : Select Able or Disable for the video noise elimination function.
setup screen To Set Day/Night 1. Select . 2. Select each item and set it properly. •• Mode : Mode is used to adjust the color of Color or Black and White. -- Color : The video is always output in color. -- B/W : The video is always output in black and white. -- Auto : Normally, it is set to Color but to B&W under low luminance at night. `` If AGC of the menu is set to , the day/night mode cannot be set to .
To Setup Special 1. Select . -- Auto : The image is automatically compensated according to the foggy level. Adjust to be more effective. -- Manual : The user manually sets the amount of compensation for each image. mode is set to , the performance is proportional to the fog level. To keep JJ `` Ifthethesetdefog defog level without regard to the fog level, set the defog mode to . `` If the manual defog level is high in a thin fog, the image may become too dark.
setup screen To Set OSD 1. Select . 2. Select each item and set it properly. •• Camera title : It specifies the name of the camera to be displayed on the screen. •• Camera title X, Y : It specifies the position of the camera name on the screen. •• Date & time : Set the time display and date formats on the screen. •• Date & Time X, Y : Specify the position of time display on the screen. •• Weekday overlay : Specify the use of date display date on the screen.
Smart codec Set a desired area of the video incoming from the camera as ROI area and specify the detection sensitivity for the area. ● setup screen 1. From the Setup menu, select the
setup screen Focus setup You can adjust the focus of video image. 1. From the Setup menu, select the
External PTZ setup Configure the connection settings to the external pan/tilt receiver so that you can control the PTZ operations via the receiver connected to the RS-485 port of the camera. )> tab 2. Click . 3. Click <▼ Show>. 4. Specify the serial port. You can set the RS-485 communication mode for pan/tilt-compliant receiver that is connected to the network camera.
setup screen Functions Supported for Each Protocol Protocol P T P control movement T control movement speed speed Zoom control Zoom movement speed Focus control Focus control speed Preset SAMSUNG-T O O (1~6) O O (1~6) O O (1~4) O O (1~4) O SAMSUNG-E O O (1~6) O O (1~6) O O (1~4) O X O PELCO-D O O (1~6) O O (1~6) O X O X O PELCO-P O O (1~6) O O (1~6) O X O X O SUNGJIN O X O X X X X X O PANASONIC O O (1~6) O O (1~6) O O (1~4) O O (1~4) O HONEY
7. Set the zoom and focus. •• [Zoom In ( )] : Zooms in the screen. •• [Zoom Out ( )] : Zooms out the screen. •• [Adjust Focus ( / )] : Adjusts the focus in the screen. •• [Zoom Speed Control ( )] : The bigger the number is, the faster the zoom speed becomes. 8. Set the preset. pan/tilt/zoom operations can be controlled only if the camera is connected to a pan/tilt MM `` The receiver with a proper . To add a preset 1. Select the preset number to add. 2. Set the name for the preset. 3.
setup screen Network Setup DDNS DDNS is an abbreviation of Dynamic Domain Name Service that converts the IP address of a camera into a general Host Name so that the user can easily remember it. JJ `` You can use the DDNS service only if the internet is connected. 1. From the Setup menu, select the )> tab. . 3. Select the connection type. 4. Type in the DDNS items according to the selected type.
Registering with DDNS To register your product with the Samsung DDNS ● setup screen 1. Visit the iPOLiS web site (www.samsungipolis.com) and sign in with a registered account. 2. From the top menu bar, select - . 3. Click [PRODUCT REGISTRATION]. 4. Enter the product ID. `` You must perform the duplicate check for the ID that you entered. 5. Select a and specify the . 6. Specify the product location with a description if necessary. 7.
setup screen To connect to the Samsung DDNS in camera setup 1. From the DDNS setup page, set to . 2. Provide the that you registered product ID with the DDNS site. )]. 3. Click [Apply ( When the connection is successfully made, you will see the message of <(Success)> on the screen. Configuring public DDNS in Camera Settings 1. Open the DDNS settings page and select for . 2. Enter the corresponding site’s host name, user name and password. )] button.
IP filtering You can create a list of IPs that you want to grant or deny access to them. 1. From the Setup menu, select the tab. ● setup screen 2. Click . 3. Select . •• Deny : If selecting this, access from those IPs that are added to the filtering will be restricted. •• Allow : If selecting this, access from only those IPs that are added to the filtering will be accepted. 4. Click the [Add ( )] button. The IP list will be created. 5.
setup screen SSL You can select a secure connection system or install the public certificate for this purpose. 1. From the Setup menu, select the tab. 2. Click . 3. Select a secure connection system. `` To access the camera using HTTPS mode, you have to type the IP address for the camera in the form of “https://”.
802.1x When connecting network, you can choose whether using 802.1x protocol, and then install the certification. 2. Click <802.1x>. 3. Set the . •• IEEE 802.1x : Specify the use of the 802.1x protocol. •• EAP type : Select EAP-TLS or LEAP. •• EAPOL version : Select version 1 or 2. •• ID : Enter the client certificate ID in EAP-TLS and the user ID in LEAP. •• Password : Enter the client private key password in EAP-TLS and the user password in LEAP.
setup screen QoS You can specify the priority to secure a stable transfer rate for a specific IP. 1. From the Setup menu, select the tab. 2. Click . )] button. 3. Click the [Add ( The IP list will be created. 4. Enter an IP address to which you will apply QoS. default prefix for IPv4 is 32; MM `` The For DSCP, the default is set to 63. `` Only the IP addresses that are set to
•• Enable SNMP Trap : SNMP trap is used to send important events and conditions to the Admin. -- Community : Enter the trap community name to receive messages. -- IP address : Enter the IP address to which messages will be sent. -- Network connection : It specifies whether an event shall be generated when the network disconnection is restored. •• Enable SNMP v3 : SNMP version 3 will be active. -- Password : Specify the default password for SNMP version 3. The default password is .
setup screen Auto IP configure You can set the IP available for access and camera searching automatically. 1. From the Setup menu, select the tab. 2. Click . 3. Set the . An additional IP address may be assigned to assess the camera from the Link-Local network. •• Auto configure : It specifies Able or Disable for the Link-Local IPv4 address. •• IP address : Display the assigned IP address.
Event Setup FTP / E-mail 1. From the Setup menu, select the tab. 2. Click . 3. Select or and enter / select a desired value. •• FTP configuration -- Server address : Enter the IP address of the FTP server that you transfer the alarm or event images to. -- ID : Enter the user ID with which you will log in to the FTP server. -- Password : Enter the user account password for logging into the FTP server.
setup screen •• E-mail configuration -- Server address : Enter the IP address of the SMTP server that you transfer the alarm or event images to. -- Use authentication : Select whether to use authorization. -- Use SSL : Specify the use of SSL. -- ID : Enter the user ID for logging into the email server. -- Password : Enter the user account password for logging into the email server.
Storage You can activate recording on your device, set the recording conditions, check the saved data capacity and format the device itself. ● setup screen 1. From the Setup menu, select the tab. 2. Click . 3. Select a device to save data in. device is properly recording data, it MM `` Ifwillyourdisplay “Recording”. `` If you see an “Error” message, check the following: -- Check the storage to see if it is connected to the device.
setup screen To make recording on the Micro SD memory 1. Set the SD card unit to . 2. Click the [Apply ( )] button. 3. Check the memory card’s and . You can format the Micro SD card by clicking the button. `` Some frames may be skipped if the Micro SD memory card operates at the lower speed than recommended. For more details, refer to “Recommended Micro SD/SDHC/SDXC Memory Card Specifications”.
5. Specify the . •• Always : Always save recorded video in the Micro SD memory card. `` If set to Always, the activation time cannot be changed. 6. When done, click [Apply ( )]. If you want to record in your NAS 1. Set the saving operation and basic recording. deletion is supported only if your NAS JJ `` Auto meets the recommended specifications. 2. Enter the information registered in your NAS. •• IP address : Unique IP address assigned to the NAS.
setup screen -- Confirm that the NAS IP address and the camera IP address are in the same format. ex) The NAS & camera subnet mask initial value is 255.255.255.0. If the IP address is 192.168.20.32 then the NAS IP address should be in the range of 192.168.20.1~192.168.20.255. -- Check whether you tried to access as another user without formatting the default folder saved or used. -- Confirm that you used recommended NAS equipment. 4. After the settings are completed, set the NAS unit to . 5.
NAS (Network Attached Storage) guide data may not be saved after a temporary network interruption when using NAS, it is JJ `` Since recommended that you use SD at the same time to prevent loss of recorded images. use, the higher priority for recording goes to the NAS. `` If you activate Overwrite to the NAS by setting it to and the available capacity is below 10%, it will be saved in the Micro SD card.
setup screen 2. If you access it as an admin, the following screen will be displayed. Click the [Control Panel]. 3. Click the in the file sharing and privilege menu. 4. Click the [Create] button. 5. After entering the shared folder name(ID), click the [OK] button to create a shared folder. In this example, the shared folder name is [testDirectory]. 6. In Windows, for NAS access, set the privilege for the shared folder as follows. Check the admin’s [Read/Write]. 7.
8. After clicking the [Create] button, enter name(ID) and password. In this example, name(ID) is set to [testID] and password is also set to [testID]. ● setup screen to the NAS recommendations, JJ `` According when you use Netgear’s NAS equipment, do not allocate the capacity for use. 9. In Windows, set the privilege for NAS access. For the shared folder created in step 4 called “testDirectory” check [Read/ Write]. 10. Basic setting in the NAS is completed. Connect your camera to the actual NAS.
setup screen Alarm output 1. From the Setup menu, select the tab. 2. Click . 3. Set the camera’s type of alarm output. `` If you change the alarm output type, the alarm out button on the monitoring page and alarm output type displayed on Event Setup page will be changed accordingly. •• Type -- Normal open : Considers “Open circuit” status of the sensor or alarm input device as normal, and triggers alarm event if becomes “Closed circuit” status.
Alarm input You can set the alarm input type, activation time, and operation mode. 1. From the Setup menu, select the tab. ● setup screen 2. Click . 3. Set whether or not to . 4. Select the type. •• Normal open : It is normally open, but if it is closed, an alarm will be triggered. •• Normal close : It is normally closed, but if it is open, an alarm will be triggered. 5. Specify the . •• Always : Always check if an alarm occurs.
setup screen 6. Specify an operation that will perform if an alarm occurs. •• FTP : Specify the use of FTP transfer in the alarm input setup. `` Refer to “FTP / E-mail” for more details. (page 93) •• E-mail : Specify the use of email transfer in the alarm input setup. `` Refer to “FTP / E-mail” for more details. (page 93) •• Record : You can set up the alarm to record to a Micro SD card or an NAS when operating. `` Set to in .
Time schedule You can set to save the video data at a certain interval as scheduled regardless of the actual occurrence of the event. ● setup screen 1. From the Setup menu, select the tab. 2. Click
setup screen Tampering detection You can set to detect tampering attempts and trigger events, such as sudden change of camera’s framing direction, blocked lens and other overall change of scenes from the video. 1. From the Setup menu, select the tab. 2. Click . 3. Set whether or not to . 4. Set the tampering detection sensitivity. The higher the sensitivity, detects the minutest tampering attempts. 5. Specify the activation time and activation condition.
MD / VA Events of motion detection and video analysis can be set to trigger event signal output. 1. From the Setup menu, select the tab. ● setup screen 2. Click . 3. Set whether or not to . 4. According to your purpose, select from motion detection and intelligent video analysis. 5. Set , and . When selected Intelligent Video Analysis, set too. 6. Select use of .
setup screen using, set the minimum and maximum motion sizes to suit desired motion range to be JJ `` Before detected. `` `` `` `` Detected size of an object may have difference with the actual size according to its shape. Up to 16 objects from the top side of the screen can be displayed. If camera is capturing a close object, the video analysis capability may degrade. In the following cases, motion detection and intelligent video analysis function may be degraded or cause improper detection.
To use Motion detection It detects a motion that meets all conditions specified by sensitivity, size and area. 1. Select a motion detection mode. ● setup screen 2. Select tab to set the sensitivity level. You can set the sensor’s sensitivity to detect a motion out of the background from the monitoring video. a situation that definitely distinguishes JJ `` Inobjects out of backgrounds, set this to a low sensitivity level.
setup screen 4. Select tab. You can specify an area on the screen to include or exclude the area to/from detection. You can specify up to 4 areas. •• Detection area : Sets the entire screen as excluded from detection, and adds specified area as motion detection area. Select 4 vertices in the image with your mouse to specify the detection area. •• Non detection area : Sets the entire screen as motion detection area, and excludes specified area as not to be detected.
To use Video analytics It detects event that meets all conditions specified by sensitivity, size and area and the event condition rules. 1. Select the video analysis mode. ● setup screen 2. Set , and . For further details on settings, refer to “To use Motion detection”. (Page 109~110) 3. Select tab. 4. Select the video analysis type. •• Passing : Detects an object passing by the line set by a user.
setup screen To set the video analysis rules `` Passing 1. Set the type to . 2. On the screen, click on preferred starting and ending point of the virtual line, then a popup window appears. 3. Select the desired rule: •• Right: Detects motions of moving from the left to the right, over the virtual line. •• Left: Detects motions of moving from the right to the left, over the virtual line. 4. Click [OK]. 5.
`` Appearing (Disappearing) 1. Set the analysis type to . ● setup screen 2. Select the desired event rule: •• Defined area based rules : It detects event of appearing object that appears in the area and remaining for a certain time period while not passing through the area borders, and opposite case of disappearing of objects existed in the area. On the screen, click four vertices to define detection area. Select the from the popup.
setup screen Face detection You can set to detect recognized face and trigger an event accordingly. 1. From the Setup menu, select the tab. 2. Click . 3. Set whether or not to . 4. Select tab to set the sensitivity level. `` As the sensitivity grows, face detection becomes more close and detailed. 5. Select the tab and select 4 vertices in the image with your mouse to specify the detection area.
Audio detection You can set to detect sound over the specified level and trigger an event accordingly. 1. From the Setup menu, select the tab. ● setup screen 2. Click
setup screen Network disconnection When the network is physically disconnected, it is considered as an event to be saved. 1. From the Setup menu, select the tab. 2. Click . 3. Set whether or not to . 4. Specify the activation time and activation condition. `` For more information about and , refer to “Alarm input”. (page 103) 5. When done, click [Apply ( )].
System Setup Product information 2. Click . 3. Check the camera information, or provide details according to your network environment. •• Model : Model name of the product. •• Serial number : Product serial number. •• Device name : Provide a device name that will be displayed on the Live screen. •• Location : Specify the location where the camera is installed. •• Description : Provide detailed information about the camera location.
setup screen Upgrade / Reboot 1. From the Setup menu, select the tab. 2. Click . 3. Select a desired item and set it appropriately. •• Upgrade : Performs upgrading the system. •• Factory default : Resets the system to the factory default. -- Except network parameter & Open SDK : Initialize all except for the network setting and lens settings as well as the open SDK installation files and internal settings. -- All : Resets all settings including the camera settings.
To perform the upgrade 1. Click [Upgrade]. 2. Click [Browse] and specify a file to upgrade. ● setup screen 3. Click [Send]. 4. The “Upgrade” dialog appears where the progression will be shown in the bottom. 5. Once completed upgrading, the browser exits and the camera restarts. may take a max of 10 minutes for the MM `` Itupgrade process. If you forcibly terminate the upgrade process, upgrade will not be completed properly. `` During restarting the system, accessing with web viewer will not be made.
setup screen To back up the current settings 1. Click [Backup]. The Save As dialog should appear. 2. Specify the backup path with a proper file name, and click [Save]. The backup file will be saved to the specified path in the format of “.bin”. To restore the backup settings 1. To restore the backup settings, click [Restore]. 2. Select a backup file and click [Open]. the backup or restoration, MM `` Iftheyouwebperform browser will be closed and the camera will reboots.
Log You can check the system log or event log. 1. From the Setup menu, select the tab. ● setup screen 2. Click . 3. Select a log type. •• System : You can check the system logs where any system changes are recorded including the time information. •• Event : You can check the event logs including the time information. 4. From the right log list, select an item to search for. •• If you select in the top left dropdown list, all logs for the applicable log type will be displayed.
setup screen Open SDK A user can install an application on their camera to execute additional functions. 1. From the Setup menu, select the tab. 2. Click . )] 3. Click the [Browse ( button to select the *.cap file from the user folder. 4. Click the [Install ( button to install your application. )] 5. The information of the installed application is displayed in the list. •• Uninstall : Deletes installed or operating applications.
Viewing profile information Profile access You can check the profile information. )] on the live screen. ● setup screen 1. Click [Status ( 2. The profile information screen is displayed. •• Profile access : Show the information of the newly added profile. -- Profile : Show the information of the newly added codec. -- Bitrate(kbps) : Show both the actual bit rate and the set bit rate. -- Framerate(fps) : Show both the actual frame rate and the set frame rate. -- ATC(%) : Show the ATC status.
appendix Specification Items Imaging Device 1/1.9” PS 2.42M CMOS Effective Pixels 1937(H) X 1097(V) approx 2.12M pixels Total Pixels Video Scanning System Min. Illumination S / N Ratio Video Out Lens Description Focus Control 1952(H) X 1241(V) approx 2.42M pixels Progressive Color : 0.015 Lux (1/30sec, F1.2, 30IRE) B/W : 0.0015 Lux (1/30sec, F1.2, 30IRE) 50dB CVBS : 1.
Items Defog Auto / Manual / Off Privacy Masking Off / On (32 zones with 4 points of polygon) Motion Detection White Balance Electronic Shutter Speed Off / On (4 zones with 4 points Polygon) Off / Low / Middle / High ATW / AWC / Manual / Indoor / Outdoor Minimum / Maximum / Anti flicker (1 ~ 1/12,000sec) Flip / Mirror Off / On Alarm I/O Input 1ea / Output 1ea Intelligent Video Analytics Audio In Audio out Serial Interface Alarm Triggers ● appendix Gain Control Operational Description Tamper
appendix Items Ethernet Video Compression Format Resolution RJ-45 (10/100BASE-T) Description H.264(MPEG-4 Part 10/AVC), Motion JPEG 1920x1080 / 1280x1024 /1280x960 / 1280x720 / 1024x768 / 800x600 / 800x450 / 720x576 / 640x480 / 640x360 / 320x240 / 320x180 H.264 : Max 60fps at all resolutions Max. Framerate Smart Codec Network Video Quality Adjustment Bitrate Control Method Motion JPEG : 1920x1080 / 1280x1024 /1280x960 / 1280x720 / 1024x768 : Max.
Items Streaming Method Max. User Access Edge Strorage Network Application Programming Interface Webpage Language Web Viewer Central Management Software Digest Login Authentication IP Address Filtering ● appendix Security Description HTTPS(SSL) Login Authentication User access Log 802.1x Authentication Unicast / Multicast 15 users at Unicast Mode SD/SDHC/SDXC - motion Images recorded in the SD/SDHC/SDXC memory card can be downloaded.
appendix Items Environmental Electrical Description Operating Temperature -30°C ~ +55°C (-22°F ~ +131°F) / Less than 90% RH / Humidity Storage Temperature -30°C ~ +60°C (-22°F ~ +140°F) / Less than 90% RH / Humidity Input Voltage / Current AC24V±10%, DC12V±10%, PoE (IEEE802.3af, Class3) Power Consumption Color / Material Mechanical Dimension (WxHxD) Weight 128_ appendix Max. 11.44W (AC 24V, 50~60Hz) Max. 10.1W (DC 12V) Max. 11.
Product Overview 147.8(5.82") Unit : mm (inch) ● appendix 66.6(2.62") 73.1(2.88") Ø 6.5 HOLE (Ø 0.26") Ø 1/4'-20 UNC-2B 14 (0.55") 67.7 (2.
appendix Troubleshooting PROBLEM I can’t access the camera from a web browser. SOLUTION yy Check to make sure that the camera’s Network settings are appropriate. yy Check to make sure that all network cables have been connected properly. yy If connected using DHCP, verify that the camera is able to acquire dynamic IP addresses without any problem. yy If the camera is connected to a Broadband Router, verify that port forwarding is properly configured. Viewer got disconnected during monitoring.
PROBLEM Can I define event rules even when I don’t use ? Cannot record into the Micro SD memory card. Micro SD memory card is inserted but the camera does not operate properly. Cannot record in the NAS. yy Yes, it can be. You can set rules for events despite of the intelligent video analysis setting. ● appendix No signal is found at the Alarm Output port even when an intelligent video analysis event is generated. SOLUTION yy Check alarm output port settings.
Open Source Announcement GPL/LGPL software license The software included in this product contains copyrighted software that is licensed under the GPL/LGPL. You may obtain the complete Corresponding Source code from us for a period of three years after our last shipment of this product by sending email to help.cctv@samsung.com If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source distribution might be charged.
GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C)1989, 1991 Free Software Foundation, Inc. 51 Franklin Street,Fifth Floor, Boston, MA 02110-1301, USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it.
3.
NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “ASIS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU.
Finally, every program is threatened constantly by software patents. States should not allow patents to restrict development and use of software on general-purpose omputers, but in those that do, we wish to avoid the special anger that patents applied to a free program could make it ffectively proprietary. To prevent this, the GPL assures that atents cannot be used to render the program non-free. he precise terms and conditions for copying, distribution and modification follow. TERMS AND CONDITIONS 0.
5. Conveying Modified Source Versions. You may convey a work based on the Program, or the modifications to produce it from the Program, in the form of source code under the terms of section 4, provided that you also meet all of these conditions: a) The work must carry prominent notices stating that you modified it, and giving a relevant date. b) T he work must carry prominent notices stating that it is released under this License and any conditions added under section 7.
7. Additional Terms. “Additional permissions” are terms that supplement the terms of this License by making exceptions from one or more of its conditions. Additional permissions that are applicable to the entire Program shall be treated as though they were included in this License, to the extent that they are valid under applicable law.
In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, not to enforce a patent (such as an express permission to practice a patent or covenant not to sue for patent infringement). To “grant” such a patent license to a party means to make such an agreement or commitment not to enforce a patent against the party.
OpenSSL Combined License The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit. See below for the actual license texts. Actually both licenses are BSD-style Open Source licenses. In case of any license issues related to OpenSSL please contact openssl-core@openssl.org. Component Name License URL openssl-1.0.1g OpenSSL Combined License http://www.openssl.org/source Copyright (c) 1998-2011 The OpenSSL Project.
BSD License Some software components of this product incorporate source code covered under the BSD license as follows. Component Name License URL net-snmp-5.7.1 pcre-8.20 openssh-5.9p1 libcap-1.2.1 lighttpd-1.4.35 Game-ws MiniUPnP Project Client pppd-2.4.5 BSD BSD BSD BSD 2.0 BSD 2.0 BSD 2.0 BSD 2.0 BSD 2.0 http://www.net-snmp.org/about/license.html http://www.kernel.org/pub/linux/libs/security/linux-privs/libcap2 http://www.opensource.org/licenses/bsd-license.html http://opensource.
3. Neither the name of the Regents of the University of California nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
The MIT License Some software components of this product incorporate source code covered under the MIT license as follows MIT License 2.0 - Acewidget, bettermeans, jquery-ui, libxml, libxml2, Mesa3D-MesaLib,mwEmbed,OpenGL Samples Pack, Wide Studio, xorg-server, dropbear-2012.55, ncurses-5.7 Copyright (c) 2011, The Dojo Foundation Copyright 2010, AUTHORS.txt (http://jqueryui.com/about) Dual licensed under the MIT or GPL Version 2 licenses. - http://jquery.org/license - http://docs.jquery.
1.11. "Source Code" means the preferred form of the Covered Code for making modifications to it, including all modules it contains, plus any associated interface definition files, scripts used to control compilation and installation of an Executable, or source code differential comparisons against either the Original Code or another well known, available Covered Code of the Contributor’s choice.
3.5. Required Notices. You must duplicate the notice in Exhibit A in each file of the Source Code. If it is not possible to put such notice in a particular Source Code file due to its structure, then You must include such notice in a location (such as a relevant directory) where a user would be likely to look for such a notice. If You created one or more Modification(s) You may add your name as a Contributor to the notice described in Exhibit A.
8.3. If You assert a patent infringement claim against Participant alleging that such Participant’s Contributor Version directly or indirectly infringes any patent where such claim is resolved (such as by license or settlement) prior to the initiation of patent infringement litigation, then the reasonable value of the licenses granted by such Participant under Sections 2.1 or 2.2 shall be taken into account in determining the amount or value of any payment or license. 8.4.
The Independent JPEG Group’s JPEG Software The software included in this product contains copyrighted software that is licensed under the JPEG license. •• JPEG license -- Code project . Generating Outline OpenGL, Libjpeg This distribution contains the sixth public release of the Independent JPEG Group’s free JPEG software. You are welcome to redistribute this software and to use it for any purpose, subject to the conditions under LEGAL ISSUES, below.
T-Kernel License - This Product uses the Source Code of T-Kernel under T-License granted by the T-Engine Forum(www.t-engine.org) T-License [License Agreement for Source Code of T-Kernel] established by T-Engine Forum on January 23, 2004 revised on June 17, 2004 revised on December 21, 2006 revised on March 24, 2009 Article 1. Scope of License Agreement 1.
Article 4. License of Source Code 1. As provided for in this Article, T-Engine Forum shall provide, and grant a license to use, the Source Code free of charge to any person who has taken the necessary procedure for registration as prescribed by T-Engine Forum and agreed to the T-License. 2. The Source Code shall be distributed exclusively by T-Engine Forum. Any person who obtains the Source Code under Article 4.1 above shall not make any re-Distribution of the Source Code. 3.
distribute the Ported Source Code as the Source Code for T-Kernel. Provided, however, that the Ported Source Code may be treated in the same way as the Modified Source Code until the time of registration hereunder. 5. The provision set forth in Article 3 shall apply to the Ported Source Code registered in accordance with this Article. Article 7. Use for Other Purpose 1.
any form of electronic, verbal, or written communication sent to the Licensor or its representatives, including but not limited to communication on electronic mailing lists, source code control systems, and issue tracking systems that are managed by, or on behalf of, the Licensor for the purpose of discussing and improving the Work, but excluding communication that is conspicuously marked or otherwise designated in writing by the copyright owner as "Not a Contribution.
BZip2 License This program, "bzip2", the associated library "libbzip2", and all documentation, are copyright (C) 1996-2007 Julian R Seward. All rights reserved. Component Name License URL bzip2-1.0.5 Bzip2 http://www.bzip.org/ Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
PHP 3.01 License The PHP License, version 3.01 Copyright (c) 1999 - 2010 The PHP Group. All rights reserved. Component Name License URL php-5.2.17 PHP 3.01 http://www.php.net/distributions Redistribution and use in source and binary forms, with or without modification, is permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
MEMO
SALES NETWORK Head Office 6, Pangyo-ro 319beon-gil, Bundang-gu, Seongnam-si, Gyeonggi-do, SEOUL 463-400 Rep. of KOREA Tel : +82-70-7147-8753, 8764 Fax : +82-31-8018-3740 www.samsungsecurity.com SAMSUNG TECHWIN AMERICA Inc. 100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660 Toll Free : +1-877-213-1222 Direct : +1-201-325-6920 Fax : +1-201-373-0124 www.samsung-security.com www.samsungsecurity.com www.samsungipolis.com SAMSUNG TECHWIN EUROPE LTD. 2nd Floor, No.
