NETWORK CAMERA Network Setup Guide
CONTENTS CHECKING NETWORK CONFIGURATION 3 Selecting the network type 11 Configure the network on the PC used for IP configuration Launching IP Installer Configuring IP installer values How to configure port forwarding Login Installing the program needed to launch the webviewer after connecting to network camera 3 NETWORK CONFIGURATION 11 SETUP SCREEN 37 12 19 22 27 31 37 web viewer-Network Setup
checking network configuration Configure the network after checking the following. 1. Check whether to use a DDNS server. - Check whether to use a DDNS for remote monitoring from outside, or to configure the system in the form of a local network for monitoring only inside the local network. 3. Before installation, check the number and locations of network cameras and the location of the monitoring PC. 4. Check the network devices to be connected to a network camera, such as IP router/hub. 5.
checking network configuration EX3) WAN Modem Router Hub Local monitoring PC Network camera 1 ... Network camera n EX4) WAN Modem Router Hub Network camera 1 Local monitoring PC 4_ Checking network configuration ...
As shown in the image below, if the monitoring PC and network camera are connected to different routers, the network camera cannot be configured, even if the IP installer is installed in the local monitoring PC. In this case, connect the configuration PC or notebook to the router (1) to set up the network camera. EX5) ● CHECKING NETWORK CONFIGURATION WAN Modem Configuration PC Router(1) Network camera 1 ...
checking network configuration If DDNS server is used: As shown in the image below, if the monitoring PC and network camera are connected to the same router, they will have the same IP range. Install the IP Installer on the local PC and use the PC for IP configuration. EX1) DDNS Server External remote monitoring PC Internet Modem Router Local monitoring PC Network camera1 ...
EX3) DDNS Server External remote monitoring PC Internet ● CHECKING NETWORK CONFIGURATION Modem Router Hub Local monitoring PC Network camera1 ... Network camera n EX4) DDNS Server Internet External remote monitoring PC Modem Router Hub Network camera1 ...
checking network configuration As shown in the image below, if the monitoring PC and network camera are connected to different routers, the network camera cannot be configured, even if the IP installer is installed in the local monitoring PC. Connect another PC or laptop for IP configuration to router (1) and configure the network camera. EX5) DDNS Server Internet External remote monitoring PC Modem Configuration PC Router(1) Network camera 1 ...
If the network environment makes it difficult to configure an IP for the network camera in a typical way: J It is difficult to change and configure the network, so it is recommended to ask the network administrator of the site to replace router (2) with a general hub, and connect the network camera. EX1) DDNS Server Internet External remote monitoring PC Modem Router(1) Router(2) Local monitoring PC Network camera 1 ...
checking network configuration EX3) WAN Modem Router(1) Router(2) Local monitoring PC Network camera 1 ... Network camera n ...
network configuration How to check the IP range of the router connected to the network camera. 1. Click Start Run Windows in the Windows screen and enter “cmd”. 2. Type “ipconfig” in the command window. Information about the IP of the PC for IP configuration connected to the router will be displayed. If the same gateway and subnet mask are used, the IP range is the same because the network camera is connected to the same router. Router Network camera 1 ...
network configuration How to configure the network environment of the PC used for IP configuration 1. Open the network environment configuration menu of the PC connected to the router. 2. Path : Control panel Network and Sharing Center Change adapter settings Local Area Connection Properties Internet Protocol Version (TCP/IPv4) Properties 3. Select "Obtain an IP address automatically" and "Obtain DNS server address automatically.
If DDNS server is not used: In the following case, launch the IP Installer on the local monitoring PC. EX1) ● NETWORK CONFIGURATION WAN Modem Router Local monitoring PC Network camera1 ... Network camera n ... Network camera n EX2) WAN Modem Router Local monitoring PC Network camera 1 Network camera 1 Hub ...
network configuration EX3) WAN Modem Router Hub Local monitoring PC Network camera 1 ... Network camera n EX4) WAN Modem Router Network camera 1 Hub ... Network camera n Local monitoring PC In the following case, connect another configuring PC to router (1) and launch the IP Installer. EX5) WAN Modem Configuration PC Router(1) Network camera 1 Router(2) Local monitoring PC 14_ network configuration ...
If DDNS server is used: In the following case, launch the IP Installer on the local monitoring PC. EX1) ● NETWORK CONFIGURATION DDNS Server External remote monitoring PC Internet Modem Router Local monitoring PC Network camera1 ... Network camera n EX2) DDNS Server External remote monitoring PC Internet Modem Router Local monitoring PC Network camera 1 ... Network camera n Network camera 5 Hub ...
network configuration EX3) DDNS Server External remote monitoring PC Internet Modem Router Hub Local monitoring PC Network camera1 ... Network camera n EX4) DDNS Server Internet External remote monitoring PC Modem Router Hub Local monitoring PC 16_ network configuration Network camera1 ...
In the following case, connect another configuring PC to router (1) and launch the IP Installer. EX5) DDNS Server Internet External remote monitoring PC ● NETWORK CONFIGURATION Modem Configuration PC Router(1) Network camera 1 ... Network camera n Router(2) Local monitoring PC In the following case, connect the configuring PC directly to the network camera and launch the IP Installer.
network configuration Buttons used in IP Installer b c Item m Description Device Name Model name of the connected camera. Click the column to sort the list by model name. However, search will be stopped if clicked during the search. b Alias This function is not currently implemented. c Mode Displays either , or for the current network connection status. MAC(Ethernet) Address Ethernet address for the connected camera.
Item Auto Set The IP Installer automatically configures the network settings. Manual Set You should configure the network settings manually. Exit Exits the IP Installer program.
network configuration How to configure an IP address automatically using [Auto Set]: 1. Launch the IP Installer on the PC for IP configuration. 2. Click the [Search] button. A list of network devices using IP addresses located at the same router is displayed. 3. Check the MAC address information and select a device to configure. 4. Click on the [Auto Set] button. [Auto Setting] window with IP Address, Subnet Mask and Gateway entered pops up. 5.
How to configure with a dynamic IP J If the network camera is set to use a dynamic IP, the monitoring PC program in the local network environment or in an external remote location may not detect the network camera. This is because IP and port may be changed when the router power is reset or recovered from a failure. To solve such problems, it is recommended to set up the port forwarding in the higher router layer.
network configuration HOW TO CONFIGURE PORT FORWARDING What is port forwarding? If using a dynamic IP through the DHCP configuration of a router, the port forwarding function allows the router to assign a static IP and camera for a specific network camera when a monitoring PC program connects to a specific network camera. In addition, when the router power is reset or recovered from a failure and its IP and port are changed, it prevents the monitoring PC program from not finding its network camera.
External remote monitoring PC ● NETWORK CONFIGURATION DDNS Server Internet Modem Router Network camera1 ... Network camera n Setting up Port Range Forward for several network cameras When several network cameras are connected to one Broadband Router device, you should forward the TCP 943 port of the router to the TCP 943 port of a connected camera.
network configuration How to configure the CISCO router 1. From the Setup menu of the Broadband Router, select - . For setting the port range forward for a third-party Broadband Router, refer to the user guide of that Broadband Router. 2. Select and for each connected camera to the Broadband Router. Each port number for the Broadband Router should match that specified in - - from the camera’s web viewer menu. 3.
Setting page addresses for each router manufacturer and how to log in to each router M The following information may be subject to change by the manufacturer. Router Manufacturer Setting page IP address ID / Password http://192.168.123.254 admin/admin Zio http://192.168.10.1 Wavecast http://192.168.200.254 http://192.168.25.1 admin/admin Linksys http://192.168.1.1 admin/1234 blank/admin Belkin http://192.168.2.1 Netgear http://192.168.0.1 admin/password admin/1234 Netop http://192.
network configuration How to enter the port forwarding menu of each router manufacturer M The following information may be subject to change by the manufacturer.
LOGIN Login by connecting to a network camera. ● NETWORK CONFIGURATION Camera connection (login) through the IP Installer 1. Launch the IP Installer. 2. Click the [Search] button to find connected cameras. 3. Select the network camera that you want to connect and double-click on it. An Internet browser is launched. 4. Enter the and to login when the login window appears. Camera connection (login) through the Internet browser) 1. Launch the Internet browser. 2.
network configuration Description of DDNS Server Operation 1. Main DDNS-related information - DDNS URL address: http://www.samsungipolis.com/Product ID 2. DDNS server operation ① To use the Samsung DDNS, visit the iPOLiS homepage (www.samsungipolis.com) and login with the product ID of camera 1/camera 2 installed in the site. ② Sign up for a membership and register your product on the DDNS server. ③ Connect the camera 1/camera 2 through the webview.
Log in the camera by using a remote PC through the DDNS server DDNS registration 1. Visit the Samsung DDNS Site http://www.samsungipolis. com to sign up for a membership. ● NETWORK CONFIGURATION 2. From the top menu bar, select - . 3. Click [PRODUCT REGISTRATION]. 4. Enter the product ID. You must perform the duplicate check for the ID that you entered. 5. Select a and specify the . 6. Specify the product location with a description if necessary.
network configuration Accessing the network camera connected to the local network. Since using the IP Installer on a remote computer that is not in the Broadband Router’s network cluster is not allowed, users can access cameras within a Broadband Router’s network by using the camera’s DDNS URL. 1. Before you can access a camera in the Broadband Router network, you should have set the port range forward for the Broadband Router. 2. Launch an Internet browser on an external remote monitoring PC. 3.
INSTALLING THE PROGRAM NEEDED TO LAUNCH THE WEBVIEWER AFTER CONNECTING TO NETWORK CAMERA Installing Silverlight Runtime To install on Windows OS 1. Click . 2. When the file download dialog pops up, click . 3. When the download is completed, click . 4. The Silverlight Runtime installation page will be displayed. to proceed with the installation. 5. When done, click .
network configuration To install on MAC OS 1. Run the file trailing with “.dmg”. 2. Run the install package file automatically created, ending with “.pkg”. 3. Click . 4. Select your language on the language selection screen, and click . 5. Click .
6. Click . ● NETWORK CONFIGURATION 7. Enter the password of the account currently logged in, and click and continue. 8. Once completed, click .
network configuration Installing STW WebViewer Plugin If connecting to a camera for the first time, you will see the installation message. Then, install the required WebViewer Plugin to access the camera and control the video from it in real time. 1. When the monitoring page is accessed for the very first time, the installation page is displayed. Click [Click Here] to begin installation.
6. Click [Install] to begin installation of the Web Viewer Plug-in. ● NETWORK CONFIGURATION 7. Click [Finish]. STW Web Viewer Plug-in installation is completed.
network configuration Using the Live Screen b c Item b c Description Monitoring Move to the monitoring screen. Playback Switch to the monitoring screen that plays recording data in the SD memory. Setup Move to the Setup screen. Viewer Screen You can use the mouse wheel to activate the digital zooming in Viewer screen. Profile type When the Web Viewer is connected, the profile information currently using is displayed.
setup screen WEB VIEWER-NETWORK SETUP Interface 1. From the Setup menu, select the tab. 네트워크 설정 ● SETUP SCREEN 2. Click . 3. Set the and as necessary. • IP type : Select an IP connection type. - Manual : Specify the IP address, Subnet mask, Gateway, DNS1, and DNS2. - DHCP : Specify the DNS1 and DNS2. - PPPoE : Specify the DNS1, DNS2, ID and Password. If you set it to , you should specify the IP, Subnet mask, Gateway, DNS 1 & 2 manually.
setup screen Port 1. From the Setup menu, select the tab. 2. Click . 3. Type in each item in the Port menu as necessary. Neither the port range between 0 and 1023 nor port 3702 is available. • HTTP port : HTTP port used to access the camera via the web browser. The default is 80(TCP). Setting the HTTP port for Safari and Google Chrome browsers to 65535 is not allowed by security policy. • • • • M Device port : Set a port used to transfer video signals with the Samsung protocols.
• Public DDNS : Select one of provided public DDNS servers when you use a public DDNS server. - Service : Select desired public DDNS service server. - Host name : Enter the name of the host that is registered with the DDNS server. - User name : Enter the user name for the DDNS service. 5. When done, click [Apply ( J 네트워크 설정 ● SETUP SCREEN - Password : Enter the password for the DDNS service. )]. If selected , be sure to select Samsung DDNS service.
setup screen IP filtering You can create a list of IPs that you want to grant or deny access to them. 1. From the Setup menu, select the tab. 2. Click . 3. Select . • Deny : If selecting this, access from those IPs that are added to the filtering will be restricted. • Allow : If selecting this, access from only those IPs that are added to the filtering will be accepted. )] button. 4. Click the [Add ( The IP list will be created. 5.
Installing the certificate 1. Enter the certificate name. 2. Select the certificate file to be installed and certificate key, and click [Install ( )] button. Deleting the certificate )] button. 2. To delete a public certificate, you should access the network video decoder in the mode of or 802.1x When connecting network, you can choose whether using 802.1x protocol, and then install the certification. 1.
setup screen QoS You can specify the priority to secure a stable transfer rate for a specific IP. 1. From the Setup menu, select the tab. 2. Click . )] button. 3. Click the [Add ( The IP list will be created. 4. Enter an IP address to which you will apply QoS. M The default prefix for IPv4 is 32; For DSCP, the default is set to 63. Only the IP addresses that are set to
Link-Local IPv4 address An additional IP address may be assigned to assess the camera from the Link-Local network. 1. From the Setup menu, select the tab. 2. Click . 네트워크 설정 ● SETUP SCREEN 3. Set the . • Auto configure : It specifies Able or Disable for the LinkLocal IPv4 address. • IP address : Display the assigned IP address. • Subnet mask : Display the subnet mask of the assigned IP. 4. When done, click [Apply ( )].
setup screen FTP / E-mail You can configure the FTP/E-mail server settings so that you can transfer the images taken with camera to your PC if an event occurs. 1. From the Setup menu, select the tab. 2. Click . 3. Select or and enter / select a desired value. • FTP configuration - Server address : Enter the IP address of the FTP server that you transfer the alarm or event images to.
SALES NETWORK SAMSUNG TECHWIN CO., LTD. Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400 TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. 100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660 Toll Free : +1-877-213-1222 Direct : +1-201-325-6920 Fax : +1-201-373-0124 www.samsungcctvusa.com www.samsungtechwin.com www.samsungsecurity.com www.samsungipolis.com SAMSUNG TECHWIN EUROPE LTD.