SAMSUNG SMARTCAM User Manual 0678 ! SNH-E6411BN
SPECIFY SERVICE INSTRUCTIONS AND WARRANTY TERMS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.
• Especially, the power cord should be installed carefully while keeping it out of children’s reach. • Never use the product near bath tub, sink, washing machine and in wet basement to avoid moisture. • The product is designed for indoor use. • The product is not designed for medical monitoring, and requires a grown-up’s protective supervision on its use.
01 Getting Started Features What’s Included 5 Part names and functions 6 Power Supply Network connection 4 · English 4 7 7 Features • Easy to install -- Simply visit the home page (www.samsungsmartcam.com) and download and install the program without a separate installer program. • Remote monitoring -- Whenever and wherever if you are in the Internet enabled environment, remote monitoring is ready for you. -- PC, laptop or smart phone can be used for monitoring.
What’s Included Check for components when opening the product package. 01 Power Adaptor Network Cable Quick Start Guide Warranty Card GPL Lisence Tapping screw Plastic anchor Getting Started Camera nn `` Please save the packaging. You will need the serial number later to register the camera.
Part names and functions Front Rear Speakers Luminance Sensor Generate audio output from your smart phone. Detects light levels where the camera is placed. Night vision mode changes according to detection result. Wi-Fi Direct button Built-in IR LEDs for night vision Built-in Mic Power / Network status LED micro SD TIGHTEN LOOSEN Camera lens Create a Wi-Fi connection for your camera and smart phone. Reset button Resets the camera settings to the default.
Power Supply Plug-in the camera power adapter to the wall outlet and connect the camera as shown. nn `` It will take about 1min for the camera to boot-up completely. When the camera has finished turning on, the LED lamp turns red and starts blinking. Connect the provided network cable with the network terminal of the camera. 01 For further details on network configuration, refer to “Network Connection and Settings”. (Page 11) LED status LED indicator shows operational status with colors.
02 Installation & Network Connection Installation Precautions Wall Mounting with Screws Adjusting the Angle Pulling out the network cable Network Connection and Settings Precautions Connecting via network cable Wi-Fi connection setting 8 · English 8 8 9 10 10 11 11 11 12 Installation Precautions 1. Install the camera in a place where the Wi-Fi signal can be reached and without interference. 2. Keep it away from humidity such as around the humidifier. 3.
Wall Mounting with Screws Assembling 1. Use drill bit of 5mm diameter and drill on the marked positions, drill to have 3 cm depth holes. Clean the holes after drilling. JJ `` Be careful not to get injured while drilling. Remove the two rubber packings on both sides of the camera installation board. Take out screws (M3xL20), and anchors (Φ5x25mm). 3. On a wooden wall, use screws to fix the wall-mount bracket as shown in the figure. Using a driver on the wall to attach, fix the screws in the two holes.
1. Place the camera installation board on flat ground. 2. Adjust the camera’s shooting angle as appropriate. Pulling out the network cable 1. Rotate the knob on the rear side of the camera in the [LOOSEN] direction to unfasten it. TIGHTEN Rotate the bracket forward if the camera angle is 90° or less to the front direction. Rotate the bracket backward if the camera angle is less than 90° to the rear side. LOOSEN LO O 10 · English TI GH N TE 3. micro SD nn `` Do not put excessive force.
Network Connection and Settings Precautions If you do not have a Wireless Access Point, you must connect the camera using LAN cable directly to your home router. 1. When you apply the power, the power status LED is lit red, and it will change to red blinking when the booting is completed. 2. Connect the network cable to the camera and to the home router as shown below. OR Internet Service 3. The status LED will become steady blue once the camera is connected to the router.
Wi-Fi connection setting If you want to connect a camera to Wi-Fi, first connect the network cable and try to make a connection to the Wi-Fi network. 1. When you apply the power, the power status LED is lit red, and it will change to red blinking when the booting is completed. 2. Use the network cable (LAN cable) to connect the LAN port of the unit to the LAN port of the Wireless Access Point. Internet Service 3.
Monitoring Web browser requirements Starting SmartCam Live Video Monitoring options Setup Basic Info Network Time Alarm & Notification Alarm Schedule SD card 13 13 13 18 19 21 Event Alarm 28 Playback 28 Information 29 My Account Support 29 30 Once you register the product with the site, you can monitor the camera video on the PC or laptop computer. Web browser requirements Windows Windows XP, 7 supported - Internet Explorer 9 or higher (The 64-bit is not supported.
❖❖ Plug in installation 3) Click to begin the installation. 4) Installation has completed. You need to install your plug in to automatically search for cameras connected to the network and view the video in your camera. login or click in a PC where the plug in is not installed, nn `` Iftheyouinstallation message window will pop up. `` 1) When you install the plug in, the web browser will be terminated and you need to launch it again.
For Mac 2) Click . 3) Click . 4) Enter MAC PC password and click . 5) Installation has completed.
5. Enter the requested information, and click . 6. According to the network connection and setting, click when the camera LED turns into green. • ID : Using alphabetical characters and numbers, make a combination using 8 to 14 letters. • Password : To strengthen security, create a password with a combination of special characters, numerals and English letters. 7. Select the serial number of the camera to be added from the camera search list.
9. Create and . 10. Click . 12. Select your Wireless Network from the list. 13. Enter the password of your Wireless Network and click . 03 nn `` The camera password is used to block the unauthorized access to your camera. Create camera password using alphanumeric characters between 1 to 8 without any space. 11. After adding the camera, click in the wireless network setup pop-up window.
15. Unplug the network cable from the camera and the router. 16. Click if the button is activated. Live Video 1. 17. Once the camera is successfully registered, you can check the camera in the camera list. Select a camera from the camera list at the upper left hand of the screen. nn `` The gray icon indicates the camera is inactive so you cannot monitor it right now. 2. Enter the camera password and click .
Monitoring options Item abc Description e Motion zone setting It detects motion within the range set by a user. f Flip You can flip over the video image. A user can directly save videos in their SD card. `` g d e n f g h i j k Item Description Network Speed i Capture Image Live video is saved as one image. j Sound `` k Full screen Brightness `` `` Set the default camera to monitor in the camera list. b Delete Camera Delete the registered camera.
❖❖ Network Speed Profile Name ❖❖ Motion detection area setting Resolution Frame rate Recommended bandwidth Low Speed Network VGA 20 fps 0.9Mbps Mid Speed Network HD(720P) 15 fps 1.2Mbps High Speed Network Full HD(1080P) 20 fps 3Mbps 1) Click the < > icon. 2) Drag it to the screen to set the detection area. 3) Click on . If you want to delete the set area, click on .
Item Setup Basic Info a Serial number You can confirm the serial number. b Camera password Click the , you can change the Camera password. Enter the current camera password, and type a new Camera password. c Camera Name Click the , you can change the camera name. d Firmware Version You can check the current version and the latest version of your camera S/W. e Status LED You can turn on/off the LED in your camera.
❖❖ Firmware update If the currently used S/W is not of the latest version, update it. If you are using the latest version, then the firmware will not be activated. 1) Click . 2) Click the < 3) When the firmware update is finished, the camera will reboot. Network > icon to update the firmware. a b you want to update the firmware, it is recommended to use a wired network nn `` Ifconnection.
nn `` If any of the manual settings is wrong, the network settings will not be applied. `` `` `` If you have both cable and wireless network connections simultaneously, the cable network connection is prioritized. If you switch from the current wireless connection to the cable connection, the network will switch to cable connection accordingly. For more information about the router or the wireless connection, refer to the documentation of the router or contact the router manufacturer.
time will synchronize with the NTP(Network Time Protocol) server automatically. nn `` The For this, Internet connection is required. Time `` `` a b c d e f Item Description a Time Confirm the camera's time. b Time Zone Select your region. c Display Time Select the time format displayed in time setting. d Automatic Time It sets camera's time automatically. e Daylight Saving Time Check this option if you live in a country or region where DST(Daylight Saving Time) is applied.
Notification Alarm & Notification The event alarm is sent through Gmail. Camera has ability to send event notifications when motion or audio is detected. a a Select the Google. 2. Enter your Gmail address and password. 3. Click . 4. Select
Push alarm Notification The push alarm is provided through the web viewer and mobile app in which the camera is registered. Alarm Schedule Alarms will only operate for the times selected by the user. a b • Push alert list shows the list of IDs of users who registered cameras. When an alarm occurs, the web site will send push alerts to each smart phone. Item 26 · English Description a Only Scheduled Time Alarm function will only operate for the time/day designated by the user.
off the camera power or set it to before removing the micro SD card. If you nn `` Turn fail to do this, the data in the micro SD camera may be damaged. SD card `` When an event occurs, it is saved in an SD card. `` `` `` Please note that the content of a micro SD card used for other purposes may be deleted when it is mounted in the camera. The following micro SD cards are recommended for this camera.
Event Alarm Playback You can play the video recorded in your SD card. You can check the event alarm that occurred. b c a d Item Description a Delete by dates Delete all the event alarms on the date. b Delete All Delete all the event alarms for thirty days. c Display Events Displays the number of events occurred in the 30 day list. d Arrange by types Arrange the event list by event types.
Information My Account 03 Monitoring you want to change the member information, click on . Select the item nn `` If(password, or email address) and enter your information.
Support You can download the Samsung SmartCam mobile app and user guide.
Appendix 04 Specifications Troubleshooting 31 33 34 Specifications OS Item Linux Description Resolution 1920x1080, 1280x720, 640x480 Max. Framerate 1080p@20fps Video Compression Format H.264, MJPEG Streaming Capability Multiple Streaming (Up to 5 Profiles) Angular Field of View (D/V/H) 128°/ 62°/ 111° Low Light Performance 0.
Item Description Audio Detection Support Audio I/O N/A Dimension (WxHxD) 63.0 x 92.1 x 41.6 Audio Compression Format G.711, G726 Weight 117g Audio Communication 2-Way Audio (Built-in Microphone & Speaker), Half Duplex Memory Slot microSD (FAT32), Up to 32GB Recording & Playback Event recording, Manual recording, Continuous recording, Remote playback Ethernet RJ-45 (10/100BASE-T) Wireless Wi-Fi 802.11 b/g/n (2.
Product Appearance 36 04 92 63 Appendix 33
Problem Troubleshooting If you encounter a problem with your system, see the table below to solve the problem as quickly and easily as possible. Please follow the instruction below: Problem Action I forgot my user ID/ password. -- Move to “Log-in page Forgot your ID/Password?”, and enter the registered e-mail address to which we will send you the user ID and/or a new password. It can be spammed out depending on the policy of the email server.
Samsung Techwin cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products. The Eco mark represents Samsung Techwin’s devotion to creating environmentally friendly products, and indicates that the product satisfies the EU RoHS Directive.
SALES NETWORK SAMSUNG TECHWIN CO., LTD. Samsung Techwin R&D Center, 6, Pangyo-ro 319beon-gil, Bundang-gu, Songnam-si, Gyeonggi-do 463-400, Korea TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. 100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660 Toll Free : 1-877-349-3149 www.samsungsv.com SAMSUNG TECHWIN EUROPE LTD.
