SMARTCAM D1 User Manual SNH-V6435DN 0678 !
SPECIFY SERVICE INSTRUCTIONS AND WARRANTY TERMS FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Smartcam D1 User Manual Copyright ©2017 Hanwha Techwin Co., Ltd. All rights reserved. Trademark Each of trademarks herein is registered.
Instructions & Warranty The manufacturer is not responsible for any loss or radio/TV interference caused by unauthorized modification of the product. Such modification will void the warranty of the product as well as the user’s right of use. WARNING • The product must be assembled and installed by an adult. • Before using, read all instructions on this manual thoroughly and follow operational instructions, warnings on this manual and printed on the product.
Contents Getting Started Features………………………………………………………… 5 What’s Included………………………………………………… 6 Part Names and Functions……………………………………… 7 Installation & Network Connection Installation……………………………………………………… 9 Network Connection and Settings……………………………… 15 Appendix Specifications…………………………………………………… 17 Troubleshooting………………………………………………… 21
Features 01 • Remote monitoring -- You can monitor your SmartCam D1 remotely, at any time and from any location, using your smartphone. • Real-time alarm -- When the bell rings, a push alarm is sent to the smartphone. • Face recognition -- You can set the person who wants to receive the alarm. • Downloading a recorded video -- You can download motion detection/audio detection/manually recorded video to the user's smartphone (Android).
What’s Included Check for components when opening the product package.
Part Names and Functions Front 01 Rear Faceplate Getting Started It can be replaced with a cover, which is additionally provided. Microphone LED Status Indicator Bell Button Power Input Connect it to an AC power cable.
Side Components Illumination Sensor WiFi Direct Button Wi-Fi is used for wireless communication between product and smartphone. RESET Reset Button Resets the product settings to the factory default. The system restarts if you press the button for 10 seconds using a pointed object such as a needle. JJ `` Speaker Hole 8 · English If you press too strongly, the button can break.
Installation Precautions Items to check before installation Cautions before installation Installing Power Stabilizer Mounting the SmartCam D1 Web Install RESET Network Connection and Settings Precautions Connection using the Wi-Fi Direct function 9 9 10 10 10 12 14 Precautions 1. As this product works on a Wi-Fi network, video receiving may be unstable if there is an obstacle (metal, wall, door) in the use environment, or if the product is receiving interference from another Wi-Fi device nearby.
Items to check before installation -- The Power Stabilizer is an electrical accessory installed with a Home-Chime. It helps ensure the camera with SmartCam D1 is receiving enough power in normal conditions. -- Please see page 12 for details regarding the connection. -- When using the chime, be sure to also install the Power Stabilizer. -- If you do not install the Power Stabilizer, the product may not operate properly. -- Check the compatibility list before installation.
Use a screwdriver to loosen the screws on the [FRONT] and [TRANS] terminals and then remove the cables. 6. FRONT Repeat Step 5 for the [Trans] cable. REAR sure to label the terminal cables nn `` Make before disconnecting them. You will need TRANS 4. to connect them to the terminal blocks later. R N S 02 RE A FR O N T A Connect Power Stabilizer to Chime TR 5. 5-1 Pull up the orange levers on the terminal block.
Mounting the SmartCam D1 3. doesn't matter which cable you use on which side of the nn `` Itterminal back. Disassembling 1. Unscrew one of the power terminals on the back of your SmartCam D1, and wrap the existing wiring from your doorbell around the terminal, and then tighten the screw. Use a screwdriver to remove your existing doorbell. Disconnect the wires from behind the doorbell carefully. 4.
Check the Diagrams below to make sure the Power Stabilizer and SmartCam D1 are properly installed. -- In the existing installation structure, a power stabilizer is removed from the figure. -- Connect two cables (black/white) with two terminals of the Chime Bell, as shown in the figure. -- If not connected, the camera and/or some features of Chime Bell may not work normally.
Network connection web Install With the Wisenet SmartCam+ app, users can monitor the SmartCam D1 from a mobile device. 1. 2. Go to Google Play/App Store and search for “Wisenet SmartCam+”. Download the application and install it on your mobile device. 3. Run the downloaded application. 4. After completing member registration, register the SmartCam D1 as instructed on the screen. nn `` For more details, refer to Wisenet SmartCam+ mobile guide.
❖❖ Bell LED Status Bell LED indicator shows operational status with blinks. Refer to table below for detailed meaning of the LED indicator. Status ON Normal Status Dim Slowly dims up & down repeatedly for 10-sec when a person is detected. Blink Blink 1. Once you are finished with the in-app setup for the SmartCam D1, attached the faceplate back on. RESET Bell LED Assemble Blinks 3-4 times with the chime when pressed 02 Blinks every 10 seconds to notify users of power supply issue.
Network Connection and Settings Precautions What is Wi-Fi Direct? If you use Wi-Fi Direct, the product can be connected to the router without using wires. 1. Connect the power adapter to the product. 2. When the power is connected, the power status LED lights up in red and starts blinking when boot-up is complete. 3. If you press and hold the Wi-Fi Direct button for 5 seconds, the LED will illuminate in yellow.
Appendix Specifications Specifications Product Appearance Home Chime Compatibility List Troubleshooting 17 17 19 20 21 Specifications Video Item Description Imaging Device 1/2.8" CMOS Min. Illumination B/W : 0 Lux with IR Angular Field of View(H / V / D) H : 125˚ / V : 94.
Digital Zoom Item 4x(Mobile) Description Item Environmental Description Flip / Mirror Off / On Operating Temperature / Humidity -20°C ~ 40°C / Less than 90% RH Intelligent Video Analytics Face Recognition, Human Detection, Motion Zone Selection Storage Temperature / Humidity -30°C ~ +50°C / Less than 90% RH Abnormal sound detection Siren, Glass breaking, Screaming Ingress Protection Weather Resistant Alarm Events Push Alert (Mobile Device) Notification via e-mail Input Voltage / Current
Product Appearance unit: mm (inch) 03 Appendix 19
Home Chime Compatibility List ❖❖ Incompatible chime ❖❖ Compatible chime Chime type Manufacturer Heath-Zenith Carlon Craftmade Edwards Mechanical Honeywell Model SL-2796 Mechanical C102X2L Electrical DH120 C212W-2L RCW100N RCW110N LA14WH BK125LWH-1 BK115LWH BK131LPB Atlantic Heath-Zenith Electrical Honeywell IQ America 20 · English Nutone Chime type DH506 LA11WH NuTone Description LA70MA (for RCW110N) Common : AC16(1), Smartcam D1(1) Transformer : AC16(3), Power stabilizer(3) Front
Problem Troubleshooting If you encounter a problem with your system, see the table below to solve the problem as quickly and easily as possible. Please follow the instruction below: Problem Action Product is not connected to the wireless hub. -- If the green light on the product state LED turns off frequently, it may be because the product is installed in an environment with a poor wireless Internet connection. -- Check the password for the wireless hub and try again.
Hanwha Techwin cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products. The Eco mark represents Hanwha Techwin's devotion to creating environmentally friendly products, and indicates that the product satisfies the EU RoHS Directive.
Head Office 6, Pangyo-ro 319 beon-gil, Bundang-gu, Seongnam-si, Gyeonggi-do, 463-400 Rep. of KOREA Tel : +82.70.7147.8753 Fax : +82.31.8018.3740 www.wisenetlife.com Hanwha Techwin America 500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666 Tel +1.877.349.3149 www.wisenetlife.com Hanwha Techwin Europe Heriot House, Heriot Road, Chertsey, Surrey, KT16 9DT, United Kingdom Tel#1 00800.801.08022 Tel#2 +31.77.326.1580 www.wisenetlife.
