제품을 올바르게 사용하여 위험이나 재산상의 피해를 미리 막기 위한 내용이므로 반드시 지켜주시기 바랍니다. 지시사항을 위반할 경우 사람이 사망하거나 중상을 입을 가능성이 예상되는 내용입니다. 지시사항을 위반할 경우 사람이 부상을 입거나 물적 손해 발생이 예상되는 내용입니다. | 전원 관련 | 설치 관련 | 청소 및 사용 관련 [여기에 있는 이미지들은 단지 참고용이며, 모든 경우(또는 국가)에 적용되지는 않습니다.] 전원플러그가 흔들리지 않도록 안쪽 끝까지 정확히 꽂아 주세요. z 접속이 불완전한 경우는 화재의 원인이 됩니다. 손상된 전원선이나 플러그, 헐거운 콘센트는 사용하지 마세요. z 감전, 화재의 원인이 됩니다. 젖은 손으로 절대 전원플러그를 만지지 마세요. z 감전의 원인이 됩니다. 반드시 접지가 된 콘센트에 전원 플러그를 연결하세요. z 전기적 쇼크(감전) 및 상해를 입을 수 있습니다. (절연1종기기에 한함) 하나의 콘센트에 여러 기기를 동시에 사용하지 마세요.
옮겨 주세요. z 전원선을 빼지 않은 상태로 옮길 경우 선이 손상되어 화재, 감전의 원인이 됩니다. 전원 플러그를 콘센트에서 분리할 때에는 반드시 플러그를 잡고 분리해주세요. z 감전, 화재가 발생할 수 있습니다. 전원플러그를 뺄 때에는 플러그를 잡고 빼 주세요. 전원선을 잡아 당겨 빼면 내부선 일부가 끊어집니다. z 전원이 켜지지 않거나 화재의 원인이 됩니다. 청소를 할 때에는 반드시 전원플러그를 빼 주세요. z 감전, 화재의 원인이 됩니다. 전원 플러그는 조작하기 쉬운 곳에 두세요. z 제품의 문제가 발생했을 경우 완전한 전원차단을 위해서는 전원플러그를 뽑아야 합니다. 본체의 전원 버튼만으로는 전원이 완전히 차단되지 않습니다. | 전원 관련 | 설치 관련 | 청소 및 사용 관련 촛불, 모기향, 담뱃불 등을 제품 위에 올려놓거나 열기구와 가까운 곳에 설치하지 마세요. z 화재의 위험이 있습니다.
기름, 연기, 습기가 많은 곳, 물(빗물)이 튀는 곳, 차량에 설치하지 마세요. z 내부로 들어가면 감전, 화재의 위험이 있습니다. 책장이나 벽장 등 통풍이 나쁜 협소한 장소에 제품을 설치하지 마세요. z 내부 온도 상승으로 인한 화재의 원인이 될 수 있습니다. 불완전한 곳이나 제품보다 작은 받침대 위에 설치하지 마세요. z 어린이가 놀다가 건드리면 제품이 떨어져 어린이가 다칠 수 있습니다. 앞부분이 무거우므로 평평하고 안정된 곳에 설치하세요. 천둥, 번개가 칠 때에는 전원선을 빼세요. z 감전, 화재의 원인이 됩니다. 테이블보나 커텐 등으로 통풍구가 막히지 않도록 하세요. z 내부 온도 상승으로 인한 화재의 원인이 될 수 있습니다. 제품을 놓을 때 살며시 놓으세요. z 고장 및 상해를 입을 수 있습니다. 제품을 이동시 떨어뜨리지 마세요. z 고장 및 상해를 입을 수 있습니다. 아이의 손이 닿는 낮은곳에 설치하지 마세요.
제품 통풍구, PC/VIDEO 단자, 전원 단자 및 배터리 단자에 젓가락, 철사, 송곳 등의 금속체나 종이, 성냥 등 불에 타기 쉬운 물건을 집어넣지 마세요. z 감전, 화재의 위험이 있습니다. 제품내부에 물 또는 이물질이 들어갔을 경우 반드시 기기 본체의 전원스위치를 끄고 전원플러그를 콘센트에서 뺀 후 서비스센터로 연락하세요. 사용자 임의로 절대 분리, 수리, 개조하지 마세요. z 수리할 필요가 있을 때에는 서비스센터로 연락하세요. 화재, 감전 사고의 원인이 됩니다. 가연성 스프레이, 인화성 물질 등을 제품과 가까운 곳에서 사용하거나 보관하지 마세요. z 폭발, 화재의 위험이 있습니다. 제품 위에 물이 담긴 그릇, 꽃병, 음료수, 약품, 작은 금속류와 무거운 물건을 올려 놓지 마세요. z 물이 제품 내부로 들어가면 감전, 화재의 원인이 되며 무거운 물건 등이 놓여져 떨어졌을 경우 다칠 수 있습니다. 제품 위에 어린아이가 좋아하는 장난감, 과자 등 물건을 올리지 마세요.
제품을 청소할 때에는 전원선을 빼고 부드러운 마른 헝겊으로 닦아주세요. z 왁스, 벤젠, 알코올, 신나, 모기약, 방향제, 윤활제, 세정제 등의 화학약품을 사용하지 마세요. 제품을 오랜 시간 사용하지 않을 때에는 전원플러그를 빼 주세요. z 먼지가 쌓여 발열, 발화 및 절연 열화에 의한 감전, 누전 화재의 원인이 될 수 있습니다. 일반 사용 조건이 아닌 특수한 장소에 설치된 제품은 주변 환경의 영향으로 심각한 품질 문제가 발생할 수 있으므로 설치 전, 반드시 당사 서비스 엔지니어에게 확인 후, 설치하세요. z 미세먼지가 많이 발생하는 곳, 화학물질을 사용하는 곳, 온도가 너무 높거나 낮 은 곳, 습기가 많은 곳, 장시간 연속적으로 사용하는 공항, 역 등의 장소 등 제품을 떨어뜨리거나 제품의 케이스가 파손된 경우에는, 제품의 전원을 끄고 전원플러그 를 뽑으세요. z 그대로 사용하면 화재, 감전의 원인이 됩니다. 서비스센터로 연락하세요.
| 제품의 특장점 | 제품의 구성 | 리모컨 | 제품 사양 | | 제품 사양 | 최신의 LCD 기술을 적용한 광학엔진 - 1024x768 패널을 채용합니다. - 3P-LCD panel 적용 합니다. - SP-L330 : 3300 lumen급 밝은 화면을 제공합니다. SP-L350 : 3500 lumen급 밝은 화면을 제공합니다. - 이동성(portable)이 좋은 작고 가벼운 외관 디자인 팬 소음 최소화 - 내부 공기 흐름과 팬 장착구조를 최적화하여 제품으로 부터 발생하는 팬 소음을 최소화 합니다. 풍부한 입력단자 - HDMI(DVI PC 신호지원), 2 D-Sub 15p, S-Video, Video 등 주변기기와의 연결성을 높였습니다. 음향 출력 - 2 개의 좌우(Stereo) 스피커를 장착하고 있으며 5밴드 Equalizer를 지원합니다. 사용자 조정의 편의성 - 사용자 조정 항목을 입력 단자별로 유지할 수 있도록 사용자 편의성을 부여합니다.
1. 표시등 5. POWER 버튼( - STAND BY (청색) ) 전원을 켜거나 끌 때 사용합니다. - LAMP (청색) 6. 렌즈 - TEMP (적색) ※ 표시등의 동작상태를 참고하세요. 7. 리모컨 수신부 2. VOL - / + 및 선택 및 이동 버튼 음량을 조절할 때 사용합니다. 8. 초점링 메뉴의 각 항목으로 이동하거나, 선택할때 초점을 맞출 때 사용합니다. 사용합니다. 9. 줌(ZOOM) 손잡이 3. MENU 버튼 화상을 확대 또는 축소할 때 사용하세요. 메뉴를 열거나 메뉴에서 나올 때, 메뉴에서 10.렌즈덮개 한 단계 앞으로 이동할 때 사용합니다. 4. SOURCE 버튼 외부기기의 신호를 선택할 때 사용합니다.
표시등의 동작상태 ●:켜져있음 STAND ◐:깜박거림 ○:꺼져있음 LAMP TEMP ● ○ ○ ● ● ○ ● ◐ ○ ○ ◐ ○ ◐ ○ ◐ ○ ◐ ◐ ● ◐ ◐ ● ● ◐ ○ ○ ◐ ◐ ◐ ◐ 램프 동작에 문제가 발생하였습니다. 아래의 조치 6을 참조하세요. ● ◐ ● 램프 수명이 다한 상태로 아래의 조치 7을 참조하세요. ◐ ◐ ● 제품 내부의 전원이 정상적으로 동작하지 않습니다. 서비스센터로 문의하세요. BY 내용 전원 공급 정상 상태로 프로젝터 동작을 위해서 리모컨이나 프로젝터의 전원 버튼을 누르면 약 30초 후 화면이 나타납니다. 프로젝터가 정상적으로 동작되고 있는 상태입니다. 프로젝터를 켜기 위해서 리모컨이나 프로젝터의 전원 버튼을 누른 후, 프로젝터가 준비 중인 상태입니다. 프로젝터를 끄기 위해서 리모컨이나 프로젝터의 전원 버튼을 누른 후, 프로젝터 내부를 냉각 시키기 위해서 냉각 시스템이 동작되고 있는 상태입니다.
동작 에러가 발생한 경우 조치 7 정보표시 화면에서 램프 사용시간을 확인 후 램프 교체를 위해 판매점이 화면 밝기가 어두워진 경우 나 서비스센터로 문의하세요. 제품 특성상 내부 온도를 낮추기 위하여 냉각팬을 사용하고 있습니다. 냉각팬 동작으로 일정 수준의 소음이 발생하지만 제품의 성능과는 관계가 없으므로 교환이나 환불의 대상이 되지 않으니 양해 바랍니다. 뒷면 1. PC OUT 출력단자 7. [AV IN] VIDEO 입력단자 2. AUDIO OUT 출력단자 8. [AV IN] S-VIDEO 입력단자 3. HDMI/DVI IN 입력단자 9. PC IN 1,2 입력단자 4. PC 1/DVI AUDIO IN 입력단자 10. [PC IN2] AUDIO 입력단자 5. RS-232C포트(서비스 입력 단자용) 11 .리모컨 수신부 6. [AV IN] R-AUDIO-L 입력단자 12. 전원입력 단자 | 제품의 특장점 | 제품의 구성 | 1. POWER ( 2.
5. V.KEYSTONE(+/-) 버튼 6. INSTALL 버튼 7. BLANK 버튼 8. P.SIZE 버튼 9. QUICK 버튼 10. MUTE ( ) 버튼 11. RETURN ( 12. EXIT ( ) 버튼 ) 버튼 13. VOL 버튼 14. INFO 버튼 15. SOURCE 버튼 16. P.MODE 버튼 17. STILL 버튼 1. POWER ( ) 버튼 전원을 켤 때 사용합니다. 2. AUTO 버튼 자동으로 화면을 조정합니다. (PC 모드에서만 동작합니다.) 3. MENU ( ) 버튼 메뉴화면을 나타낼 때 사용합니다. 4. 이동(▲ ▼ ◀ ▶)/( ) 버튼 메뉴의 각 항목으로 이동하거나 선택할 때 사용합니다. 5. V.KEYSTONE(+/-) 버튼 화상이 찌그러지거나 기울어지는 현상이 발생할 때 사용합니다. 6. INSTALL 버튼 투사 이미지를 반전 또는 역상시킬 때 사용합니다. 7. BLANK 버튼 일시적으로 영상과 음성을 차단할 때 사용합니다.
14. INFO 버튼 외부입력 신호, 화면설정, PC화면조정, 램프수명 등의 상태를 볼 때 사용합니다. 15. SOURCE 버튼 TV/외부입력 신호를 전환하는 버튼입니다. 16. P.MODE 버튼 화면모드를 선택할 때 사용합니다. 17. STILL 버튼 정지화면으로 볼 때 사용합니다. | 제품의 특장점 | 제품의 구성 | 리모컨 외부 디자인과 제품 규격은 제품의 성능 향상을 위하여 사전 통지 없이 변경될 수 있습니다. 제품 규격 모델명 SP-L330 / SP-L350 패널 타입 0.63" 3LCD w/MLA 해상도 XGA (1024 x 768) 화면비 4:3 SP-L330 : 최대 3,300 ANSI 루멘 (절약모드 2200 루멘) 밝기 SP-L350 : 최대 3,500 ANSI 루멘 (절약모드 2200 루멘) 명암비 최대 400:1 대각 화면 크기 40 ~ 300" 투사 거리 1 m ~ 10 m Zoom 조정 수동 Focus 조정 수동 Lens F=1.
LCD 프로젝터에서 사용하는 LCD 패널은 수십만개의 미세한 화소로 이루어져 있습니다. 다른 많은 영상표현소자와 마 찬가지로, LCD 패널은 동작하지 않는 불량화소를 포함할 수 있습니다. 불량화소를 판별하는 조건과 LCD 패널이 포함 할 수 있는 불량화소의 수량은 규격상 정해진 기준에 의해 LCD 패널 생산업체와 당사의 제품 출하시에 엄격하게 관리 되고 있습니다. 일부 화면상 표시되지 않는 화소가 나타날 수 있으나, 이는 전반적인 화질 및 제품의 수명에 영향을 미 치지 않습니다. 지원하는 디스플레이 모드 PC Timing (D-Sub/HDMI) Format 해상도 수평 주파수 (kHz) 수직 주파수 (Hz) 클럭주파수 (MHz) IBM 640 x 350 70Hz 31.469 70.086 25.175 IBM 640 x 480 60Hz 31.469 59.940 25.175 IBM 720 x 400 70Hz 31.469 70.087 28.
Format 해상도 Scan BT.601 SMPTE 267M 480i 59.94Hz Interlaced BT.1358 SMPTE 293M 480p 59.94Hz Progressive BT.601 576i 50Hz Interlaced BT.1358 576p 50Hz Progressive 720p 59.94Hz/60Hz Progressive 720p 50Hz Progressive 1080i 59.94Hz/60Hz Interlaced 1080i 50Hz Interlaced SMPTE 296M BT.709 SMPTE 274M AV Timing (HDMI) Format 해상도 Scan 수평 주파수 (kHz) 수직 주파수 (Hz) 클럭주파수 (MHz) EIA-861 Format1 640 x 480 Progressive 59.940 31.469 25.
| 기본 설정 | 전원 연결 프로젝터 설치 스크린과 투사광이 수직이 될 수 있도록 설치해 주세요. 렌즈는 화면의 중앙에 맞추어 주세요. 화면과 수직으로 설치되어 있지 않을 경우 화면이 직사각형이 되지 않을 수도 있습니다. 스크린을 밝은 곳에 설치하지 마세요. 화면이 밝게 되어 잘 보이지 않습니다. 스크린을 밝은 장소에 설치할 때는 커튼을 쳐 주세요. 전면 바닥 / 전면 천장 / 후면 바닥 / 후면 천장으로 설정이 가능합니다. (설치위치 설정 보기) 화면 뒤쪽에 설치하여 보려면 시청자와 화면의 뒤쪽에 프로젝터를 설치할 경우 반투명 스크린을 설치하세요. 메뉴 > 설정 > 설치 > 후면 바닥 을 선택하세요. 화면 앞쪽에 설치하여 보려면 일반적으로 시청자가 보는 쪽에 설치하세요. 메뉴 > 설정 > 설치 > 전면 바닥 을 선택하세요. 줌과 초점 조정하기 줌 손잡이 초점링 줌 손잡이를 돌려 줌 범위 안에서 이미지를 원하는 크기로 조정할 수 있습니다.
지정된 투사거리(스크린 크기와 투사거리 참조)를 벗어난 위치에 제품을 설치 하게 되면 초점 조절이 안될 수 있습니다. 높이 조정용 다리 조정하기 프로젝터의 높이 조정용 다리를 돌려 프로젝터가 수평이 되도록 조정하세요. 프로젝터는 기준 위치에서 30mm (약 12도)까지 높이 조절이 가능합니다. 프로젝터의 설치 상태에 따라 화상이 찌그러지는(키스톤) 현상이 발생 할 수도 있습니다. 키스톤 현상이 발생하면 수직 키스톤 으로 조정하세요. 스크린 크기와 투사거리 최적의 화면을 실현하기 위해 프로젝터의 다리를 평평하고 높이를 같게 설치하세요. 만약 화면이 선명하지 않으면 줌 손잡이 및 초점링을 조정하거나 프로젝터를 앞, 뒤로 움직이세요. 화면 크기 가로 세로 최대 최소 Offset (M:인치) (X:mm) (Y:mm) (Z:mm) (Z:mm) (Y':mm) 40 812.8 609.6 1376 1140 102 50 1016.0 762.
80 ~ 120 형의 스크린 크기가 최적의 화면을 구현하도록 설정되어 있습니다. A. 스크린 Z: 투사거리 Y': 렌즈 중심에서부터 이미지의 아래쪽 끝부분까지의 거리 수평 키스톤 조정 방법 1. 화면 크기에 따른 투사거리를 확인한 다음, 프로젝터를 설치하세요. (아래표 참조) 화면크기(m) 투사거리 대각선 가로 세로 (m) 1 0.8 0.6 1.4 1.3 1 0.8 1.7 1.5 1.2 0.9 2.1 1.8 1.4 1.1 2.4 2 1.6 1.2 2.8 2.3 1.8 1.4 3.1 2.5 2 1.5 3.4 2.8 2.2 1.7 3.8 3 2.4 1.8 4.1 3.3 2.6 2 4.5 3.6 2.8 2.1 4.8 3.8 3 2.3 5.1 4.1 3.3 2.4 5.5 4.3 3.5 2.6 5.8 4.6 3.7 2.7 6.2 4.8 3.9 2.9 6.5 5.1 4.
4. MENU 버튼을 눌러 테스트 패턴의 Crosshatch 화면을 띄웁니다. 설정 → 테스트 패턴 → Crosshatch 5. 아래 그림에서 ①번과 ②번이 서로 평행 상태가 되도록 프로젝터의 위치를 조정합니다. 스크린 Crosshatch 테스트 패턴 ① 실 등을 이용하여 만든 스크린 상의 가상의 수직라인 ② 테스트 패턴 정중앙의 수직라인 6. 투사 화면의 모서리(프로젝터와 가장 가까운 쪽)와 스크린의 모서리가 맞도록 프로젝터의 각도를 조정합니다. A : 프로젝터 B : 스크린 C : 투사화면 D : 프로젝터와 가장 가까운 쪽의 화면 모서리 → 투사화면이 스크린의 전영역을 포함하도록 조정 (프로젝터의 설치 높이에 따라 투사화면이 스크린의 전 영역을 포함하지 못할 수도 있습니다. 이 경우에는 스크린의 전 영역을 포함 할 수 있도록 프로젝터의 각도를 조정하세요.) 7. 리모컨의 V.KEY-STONE 버튼을 누르세요. 수직 키스톤 메뉴가 나타납니다.
8. ▲ 또는 ▼ 버튼을 눌러 수평 키스톤을 선택합니다. 리모컨의 + 또는 - 버튼을 이용하여 수평 키스톤을 조정합니다. - A : 프로젝터 - B : 스크린 - C : 투사화면 테스트 패턴의 수평라인이 스크린 외곽 수평라인과 평행 이 되도록 조정합니다. → 9. 줌 손잡이로 이용하여 화면 크기를 조정합니다. 10. 스크린보다 더 크게 투사되는 부분이 발생하면 화면 크기의 사용자 조정 메뉴를 이용하여 투사화면의 크기를 조정하세요. 조정 방법 : 1. MENU 버튼을 누르세요. 2. 화면의 화면 크기 메뉴를 선택합니다. 3. 사용자 조정 메뉴를 선택한 다음, 조정할 위치를 선택합니다. 4. ▲ 또는 ▼ 버튼을 이용하여 화면 크기를 조정합니다. - A : 프로젝터 - B : 스크린 - C : 투사화면 → 키스톤은 화상의 기울어짐 현상을 보정하는 기능으로 키스톤이 동작하면 밝기 및 해상도가 다소 떨어질 수 있습니 다.
3. [고급] 버튼을 클릭하세요. 새로운 설정 관련창이 나타납니다. 4. [모니터] 탭을 클릭한 다음 프로젝터에서 지원하는 디스플레이모드 표의 <수직 주파수(Vertical Frequency)>를 참고하여 <화면 재생 빈 도>를 설정하세요. <화면 재생 빈도> 대신 수직 주파수와 수평 주파수를 설정할 수 있는 경우 둘 다 설정하세요. 5. [확인] 버튼을 클릭하여 창을 닫고 <디스플레이 등록 정보>창의 [확 인] 버튼을 클릭하여 닫으세요. 이때 자동으로 재부팅이 될 수도 있습니다. 6. PC를 종료하고 프로젝터와 연결하세요. PC종류나 사용하고 있는 윈도의 버전에 따라 위의 설명과 약간 다를 수 있습니다. (예:1번의 [속성(R)] 대신 [등록정보]로 나타남) 이 제품은 PC 모니터로 사용할 경우 <색 품질>의 24비트까지 지원합니다. 제조사나 윈도의 버전에 따라 프로젝터로 봤을 때 기존 모니터와 약간 다르게 나타날 수 있습니다.
| 기본 설정 | 전원 연결 | 외부기기 연결 D-Sub 케이블로 PC 연결하기 먼저 PC와 프로젝터가 꺼져 있는지 확인하세요 프로젝터 뒷면의 [PC IN (1 또는 2)] 단자와 PC의 D-Sub 단자를 D-Sub 케이블로 연결하세요. - 지원하는 입력신호는 "PC Timing(D-Sub/HDMI)"를 참조하세요. 프로젝터 뒷면의 [PC 1/DVI AUDIO IN] 단자 또는 [AUDIO IN 2] 단자와 PC의 Audio out 단자를 오디오 케이블(미제공)로 연결 하세요.
먼저 PC와 프로젝터가 꺼져 있는지 확인하세요 프로젝터의 [HDMI/DVI IN] 단자와 PC의 DVI 단자를 HDMI/DVI 케이블(미제공)로 연결하세요. - PC의 HDMI 단자와 연결할 때에는 HDMI 케이블(미제공)로 연결하세요. - 지원하는 입력신호는 "PC Timing(D-Sub/HDMI)"를 참조하세요. 프로젝터의 [PC 1/DVI AUDIO IN] 단자와 PC의 Audio out 단자를 오디오 케이블(미제공)로 연결하세요. - HDMI 케이블로 연결한 경우에는 오디오 케이블(미제공)을 연결할 필요가 없습니다. 외부 모니터 연결하기 프로젝터와 동시에 별도의 모니터로 영상을 볼 수 있습니다. 먼저 PC와 프로젝터가 꺼져 있는지 확인하세요. 프로젝터 뒷면의 [PC IN 1] 단자와 PC의 D-Sub 단자를 D-Sub 케이블로 연결하세요. 프로젝터의 [PC OUT] 단자와 모니터의 D-Sub 단자를 D-Sub 케이블로 연결하세요.
- [PC OUT] 기능을 이용하여 모니터를 연결할 경우 반드시 [PC IN 1]에 PC를 연결해야 합니다. - 리모컨의 [Blank] 버튼을 눌러 프로젝터의 화면이 보이지 않아도 [PC OUT]으로 연결된 모니터의 화면은 정상적으로 출력됩니다. - 대기모드에서도 [PC OUT] 기능은 동작합니다. HDMI 호환 기기 연결하기 먼저 AV 기기와 프로젝터가 꺼져 있는지 확인하세요. 프로젝터 뒷면의 [HDMI/DVI IN] 단자와 디지털 출력 기기의 DVI 출력 단자를 HDMI/DVI케이블로 연결하세요. - 디지털 출력 기기의 HDMI 출력 단자와 연결할 때에는 HDMI케이블로 연결하세요. - 지원하는 입력신호는 "AV Timing(HDMI)"를 참조하세요. 프로젝터의 [PC 1/DVI AUDIO IN] 단자와 디지털 출력 기기의 Audio out 단자를 오디오 케이블(미제공)로 연결하세요. - HDMI 케이블로 연결한 경우에는 오디오 케이블(미제공)을 연결할 필요가 없습니다.
프로젝터 뒷면의 [PC IN (1 또는 2)] 단자와 AV 기기의 D-Sub 단자를 D-Sub 케이블로 연결하세요. - 지원하는 입력신호는 "AV Timing (D-Sub)"를 참조하세요. 프로젝터 뒷면의 [PC 1/DVI AUDIO IN] 단자 또는 [AUDIO IN 2] 단자와 AV 기기의 Audio out 단자를 오디오 케이블(미제공)로 연 결하세요. Component 출력 AV 기기 연결하기 먼저 AV 기기와 프로젝터가 꺼져 있는지 확인하세요. 프로젝터 뒷면의 [PC IN (1 또는 2)] 단자와 AV 기기의 COMPONENT 단자를 D-Sub/Componet 케이블(미제공)로 연결하세요. - 지원하는 입력신호는 "AV Timing(D-Sub)"를 참조하세요 프로젝터 뒷면의 [PC 1/DVI AUDIO IN] 단자 또는 [AUDIO IN 2] 단자와 AV 기기의 Audio out 단자를 오디오 케이블(미제공)로 연결하세요.
먼저 AV 기기와 프로젝터가 꺼져 있는지 확인하세요. [VIDEO] 또는 [S-VIDEO] 단자와 AV 기기를 VIDEO 케이블(미제공) 또는 S-VIDEO(미제공)케이블로 연결하세요. - 지원하는 입력신호는"AV Timing(VIDEO/S-VIDEO)"를 참조하세요. 프로젝터 뒷면의 [AV IN R-AUDIO-L] 단자와 AV 기기의 AUDIO OUT 단자를 오디오 케이블(미제공)로 연결하세요. 외부 스피커 연결하기 프로젝터 내부 스피커 대신 내장된 외부 스피커로 음향을 들을 수 있습니다. 외부 스피커에 적합한 오디오 케이블(미제공)을 준비하세요. 프로젝터의 [AUDIO OUT] 단자와 외부 스피커를 오디오 케이블로 연결하세요. - 외부 스피커를 연결하여 사용할 경우 프로젝터의 내부 스피커는 동작하지 않으나 프로젝터(리모컨 포함)의 VOL 버튼으로 외부 스피커의 음량 조절은 가능합니다. - [AUDIO OUT] 단자는 입력된 음성신호 모두를 출력할 수 있습니다.
| 기본 기능 | 입력 | 화면 | 설정 | 부가기능 | 부가기능 | 프로젝터 켜기 렌즈 덮개가 완전히 열려 있는지 확인하세요. 전원을 연결하세요. 청색 STAND BY LED 표시등이 켜졌는지 확인하세요. 전원 버튼을 누르세요. (리모컨 또는 상단의 전원버튼) 켜지는 동안 청색 LAMP LED 표시등이 깜빡거립니다. 다 켜지면 LAMP LED 표시등이 청색을 유지합니다. 램프가 충분히 식지 않은 상태에서 프로젝터를 켜면 램프를 일시적으로 식히기 위해서 팬의 회전속도가 높아지게 되는데 이럴 경우 소음이 크게 들릴 수 있습니다. 프로젝터 끄기 전원 버튼을 누르세요. (리모컨 또는 상단) 확인 또는 취소가 나타납니다. 방향키(리모컨 또는 상단)로 '확인'을 선택하세요. Enter 버튼 누르거나 전원 버튼을 한번 더 누르세요. STAND BY LED 표시등은 꺼지고 LAMP LED 표시등이 깜빡거립니다. 램프를 빠르게 식히기 위해 냉각 팬의 속도가 올라갑니다.
1) PC 1 5) HDMI 2) PC 2 3) AV 4) S-영상 외부입력 편집 프로젝터에 연결된 기기들의 명칭을 편집할 수 있습니다. 1) VCR 7) DVD 리시버 2) DVD 8) 게임 3) 케이블 셋톱박스 9) 캠코더 4) HD 셋톱박스 10) DVD 콤보 5) 위성 셋톱박스 11) PC 6) AV 리시버 | 기본 기능 | 입력 | 화면 | 설정 * 조정 방법을 동영상으로 보려면 아래의 아이콘( 화면조정 모드 설명 / | 부가기능 ) 을 클릭하세요. 동작 / 정지 프로젝터에 맞추어 둔 화면상태를 선택하거나, 사용자가 원하는 대로 화면의 분위기를 바꿉니 다. 1) 모드 - 표준 화면 다양한 경우에 가장 일반적으로 사용할 수 있는 화면모드입니다. - 프리젠테이션 프리젠테이션을 할 때 적합한 화면모드입니다. - 텍스트 문서 작업을 할 때 적합한 화면모드입니다. - 영화 화면 영화를 볼 때 적합한 화면모드입니다.
4) 선명도 : 사물의 윤곽을 선명하게 또는 흐리게 조정합니다. ▶ 입력신호가 PC Timing(D-Sub/HDMI)에서는 선명도를 조정할 수 없습니다. 5) 색농도 : 사물을 연하게 또는 진하게 조정합니다. ▶ 입력신호가 PC Timing(D-Sub/HDMI)에서는 색농도를 조정할 수 없습니다. 6) 색상 : 사물의 색을 녹색/적색으로 바꿔 자연스럽게 조정합니다. 명암 밝기 선명도 색농도 색상 ▶ 입력신호가 PC Timing(D-Sub/HDMI)과 [S-영상],[AV] 모드의 PAL,SECAM 방식에는 색상을 조정할 수 없습니다. 7) 색온도 조정 : 사용자의 기호에 따라 색온도를 선택할 수 있습니다. - 제품 출하 시 조정된 색온도 : 5500K, 6500K, 8000K, 9300K - 사용자의 기호에 따라 아래 항목으로 추가 조정할 수 있습니다. 색온도 조정 R-Gain, G-Gain, B-Gain : White level의 색온도를 조절합니다.
보일 수 있습니다. 이 경우에는 오버스캔을 동작(오버스캔 동작)시키세요. 필름모드 영화를 감상할 때 최적의 화면상태로 시청하기 위해 화면상태를 설정하는 것입니다. 필름모드 가 동작된 상태에서 영화로 제작된 화면을 자연스럽게 볼 수 있습니다. 1) 끄기 2) 동작 ▶ 필름모드는 [AV], [S-영상], 480i, 576i 신호에서만 지원합니다. PC 화면 떨림과 반짝거림 같은 불안정한 화면을 발생시키는 노이즈(잡음) 현상을 제거, 감소시킵니다. 미세조정으로 노이즈(잡음) 현상이 제거되지 않으면 주파수 조정을 최대한으로 조정한 후 다시 미세조정을 하세요. 자동 조정 ▶ D-Sub 단자의 PC Timing 입력에서만 활성화됩니다. 주파수 조정 ▶ " PC Timing (D-Sub/HDMI) "의 내용을 참조하세요. 미세 조정 1) 자동 조정 : PC 화면의 주파수와 위상을 자동으로 조정할 수 있습니다. 2) 주파수 조정 : PC 화면에 수직 줄무늬가 나타날 경우 주파수를 조정하세요.
수 있습니다. 수직 키스톤 프로젝터의 화상이 상하 방향으로 스크린에 수직으로 나타나지 않을 경우 수직 키스톤 기능을 사용하여 화상을 보정할 수 있습니다. 수평 키스톤 프로젝터의 화상이 좌우 방향으로 스크린에 수평으로 나타나지 않을 경우 수평 키스톤 기능을 사용하여 화상을 보정할 수 있습니다. '수평 키스톤 조정 방법' 참조 ▶ 키스톤은 화상의 기울어짐 현상을 보정하는 기능으로 키스톤이 동작하면 화질이 다소 떨어 질 수 있습니다. 바탕 화면 프로젝터에 연결되어 있는 외부기기에서 신호가 없을 때 나타나는 바탕 화면을 지정할 수 있 습니다. 신호가 있으면 설정한 바탕 화면은 사라지고 정상적인 화면이 나타납니다. 1) 로고 2) 파란색 3) 검정색 테스트 내부에서 생성하는 패턴으로 프로젝터 설치 시 기준 화면으로 활용할 수 있습니다. 패턴 Crosshatch 1) Crosshatch : 화면의 전체적인 화상 왜곡 여부를 확인할 수 있습니다. 2) 화면 크기 : 1.33:1, 1.
* 조정 방법을 동영상으로 보려면 아래의 아이콘( 화면조정 메뉴 언어 설명 / ) 을 클릭하세요. 동작 / 정지 메뉴화면의 언어를 선택합니다. 메뉴 부가기능 1) 위치 선택 메뉴의 위치를 상/하/좌/우 원하는 위치로 이동할 수 있습니다. 2) 투명도 위치 선택 메뉴화면의 투명도를 선택합니다. - 매우 투명하게 - 투명하게 투명도 - 약간 투명하게 - 불투명하게 표시시간 3) 표시시간 메뉴화면의 표시시간을 설정 할 수 있습니다. - 5 초 / 10 초 / 30 초 / 60 초 / 90 초 / 120 초 / 계속 켜짐 음향 필터 점검 주기 프로젝터 내부의 3W stereo speaker의 좌우 음균형과 Equalizer를 조정합니다. 1) 음균형 4) 1kHz 2) 100Hz 5) 3kHz 3) 300Hz 6) 10kHz 필터의 점검 주기를 설정합니다.
3) 20 분 4) 30 분 정보 표시 외부입력 신호, 화면설정, PC화면조정, 램프 사용시간 등의 상태를 볼 수있습니다.
| 고장신고 전 확인사항 | 설치 및 연결 문제 해결 전원이 들어오지 않아요. z 전원선의 연결 상태를 확인하세요. 프로젝터를 천장에 설치하고 싶어요. z 천장 걸이용 지지대는 별매품 이므로 판매점에 문의하세요. 외부기기가 선택되지 않아요. z 외부기기 연결선(영상선)이 신호 단자에 맞게 연결되었는지 확인하고, 연결 상태를 점검하세요. 제대로 연결되지 않은 상태에서는 기기가 선택되지 않습니다. 메뉴와 리모컨 문제 리모컨이 동작하지 않아요. 해결 z 리모컨 각도와 거리가 적당한지 제품과 리모컨 사이에 장애물이 없는지 확인하세요. z 삼파장류의 형광등 같은 조명 기구가 직접적으로 리모컨 센서부위에 영향을 줄 경우 오동작이나 리모컨 감도에 영향을 줄 수 있습니다. 메뉴가 선택되지 않아요. z 리모컨 건전지가 다 소모되었는지 확인하세요. z 프로젝터 윗면의 표시등에 불이 들어와 있는지 확인하세요. z 메뉴가 회색으로 나와 있는지 확인하세요.
| 보관 및 관리 | 서비스센터 안내 | 기타 | 외관 및 렌즈 손질을 하려면 부드러운 마른 헝겊으로 닦으세요. 벤젠, 신나 등의 인화물질이나 젖은 헝겊으로 닦지 마세요. 고장의 원인이 됩니다. 손톱이나 날카로운 물건으로 제품을 닦지 마세요. 긁혀서 자국이 남을 수 있습니다. 내부청소를 하려면 내부청소는 구입한 대리점이나 서비스센터에 문의하세요. (유료) 먼지나 이물질 등이 내부에 끼어있다면 연락하세요. 램프 교환 방법 프로젝터 램프 교환시 주의 사항 프로젝터의 램프는 소모성 부품임으로 최적의 작동을 위해서는 램프 사용 시간에 따라 교환하세요. 램프 사용 시간은 정보표시(INFO 버튼)에서 확인할 수 있습니다. 램프를 교체할 때 제품규격에 맞는 램프를 사용해야 합니다. 아래에서 명시되어 있는 동일 모델의 램프로 교체하세 요. - 램프 모델명 : 220W UHP E19.5 - 램프 제조사 : Philips 램프를 교체 하기 전에 항상 전원선이 분리 되어 있는지 확인 하세요.
프로젝터 램프 교환 순서 램프는 고온, 고압 제품이므로 전원선 분리 후 최소 1시간이 지난 후에 작업을 진행하세요. 램프는 제품의 측면(전면기준 좌측면)에 위치해 있습니다. 사진에 표시된 부분의 나사를 분리한 사진에 표시된 2개의 나사를 분리하 사진과 같이 램프 손잡이를 잡고 당기 다음 덮개를 열어 주세요. 세요. 세요. 새로운 램프의 결합 순서는 분해순서의 반대로 진행해 주세요. 램프 불량 서비스 안내 제품 무상 서비스 기간 ▷ 소모성 램프 불량 : 구입일로부터 6개월 이내 ▷ 유무상 서비스 접수처 : 삼성전자서비스 (1588-3366) 부품 구입처 안내 ▷ 제품구입처 ▷ 삼성전자서비스 (1588-3366) 필터 교환 및 청소 프로젝터 필터 교환시 주의 사항 필터는 제품의 밑면에 위치해 있습니다. 프로젝터의 전원을 끄고 제품의 열이 충분히 식은 다음 전원플러그를 뽑으세요. 그렇지않을 경우 내부의 열로 인하여 부품이 손상될 수 있습니다. 필터를 교환할 때에는 먼지가 발생할 수 있습니다.
필터를 청소 또는 교환 후에는 필터 사용시간 초기화를 실행시키세요. 부품 구입처 안내 ▷ 제품구입처 ▷ 삼성전자서비스 (1588-3366) 통풍구 프로젝터 통풍구 위치 통풍구는 좌우와 밑면에 위치해 있습니다. | 보관 및 관리 | 서비스센터 안내 | 기타 | 제품의 모델명, 고장상태, 연락처를 정확히 알려 주시면 고객 여러분의 궁금점에 대하여 신속한 서비스를 제공하겠습니다. 전화 번호와 주소는 예고 없이 변경 될 수 있습니다.
| 보관 및 관리 | 서비스센터 안내 | 기타 | 저작권 재활용 센터환경보호 및 자원 재활용을 위해 폐 전자제품은 다음과 같이 처리하셔야 합니다. 무료처리 삼성전자 대리점으로 부터 제품을 새로 구입하고 기존 제품을 버리고자 하는 경우, 신제품 배달시 무료로 처리해 드립니다. 유료처리 신규 제품 구입 없이 기존에 사용하던 제품을 버리고자 하는 경우, 관할 동사무소에 연락하시어 처리하시면 됩니다.
삼성전자의 [녹색경영] 삼성전자는 1992년 6월 환경 경영 체제 구축을 통해 환경오염 사고를 예방하고, 지속적인 개선을 위한 '환경방침'을 발표한 데 이어 1996년 5월 [녹색경영]을 선언하였습니다. 삼성전자의 녹색경영은 환경, 안전, 보건을 기업 경영 활동의 핵심요소로 인식하고 이를 적극 추진 함으로써 인류의 풍요로운 삶의 구현과 지구환경 보전에 동참하겠다는 의지의 표현입니다. | 보관 및 관리 | 서비스센터 안내 | 기타 | 본 설명서에 있는 내용은 성능 개선을 위해 사전 예고 없이 변경될 수 있습니다. ©2009 삼성전자주식회사 본 설명서의 저작권은 삼성전자(주)에 있습니다. 삼성전자(주)의 사전 허가 없이 설명서 내용의 일부 또는 전부를 무단 사용하거나 복제하는 것은 금지되어 있습니다.