Contents • Table of Contents ……………………………………………………………… 2 • Safety caution…………………………………………………………………… 3 • Main Features and Characteristics… …………………………………… 5 1. Introduction… ……………………………………………………………………………… 5… 2. Characteristics……………………………………………………………………………… 5 • Controller Button Layout …………………………………………………… 6 • Package Contents……………………………………………………………… 6 • System Diagram ………………………………………………………………… 6 1. Wiring Diagram… …………………………………………………………………………… 7… 2.
Safety caution Caution • Use the appliance indoors only. - Do not place the appliance outdoors or expose it to rain or moisture. - If dropped in water, the appliance may be corroded and damaged. • Do not use the appliance where there is excessive dust, smoke, or moisture. - Using the appliance under such conditions may result in fire, electric shock or serious damage. • Do not operate the appliance in temperatures beyond those specified. - Excessive heat or cold may damage the appliance.
System Diagram Controller Button Layout Tx1+ Tx1Tx2+ Tx2Tx3+ Tx3TRx+ TRx- 1. Wiring Diagram RS-485/422 Signal Wire Package Contents 2. Connecting RS-485/422 Signal Wires · RS485 Communications Power Adapter (DC 12V) Terminal Block Camera Controller RXD+ RXD- Tx1+ Tx1- · RS485 Communications SPC-1010 User’s Manual PTZ CONTROLLER 6 User Guide Camera Controller RXD+ RXDTXD+ TXD- Tx1+ Tx1TRx+ TRx- • You may use the Tx2 or Tx3 terminal instead of Tx1.
Controlling PTZ Camera Names and Functions ① ② ⑤ 1. Power ① To turn on the power, press the PWR button. ② To turn off the power, hold down the PWR button. 2. Initial Screen Display SAMSUNG-T ③ ④ ⑥ ① ESC / POWER Cancels a command or turns power on/off. ② LCD DISPLAY 16 X 2 LCD ③ Number Pad Enables changing channels or opening and closing the camera OSD. ④ 1. LOCK 2. FN 3. AUX 4. SET 5. OPEN 6. CLOSE Locks out the system.
Controlling PTZ Camera Controlling PTZ Camera 4. Pan / Tilt / Zoom Using Joystick 5. Iris / Focus / Zoom Buttons ■ You can use the joystick to control the camera's Pan and Tilt operations. ■ The farther you move the joystick from the center, the faster the camera moves. ① Screen Brightness ■ To adjust the camera's screen brightness, use the OPEN and CLOSE buttons.
Controlling PTZ Camera Controlling PTZ Camera 7. SWING 10. OSD ■ The Swing function commands the camera to move between 2 selected locations, monitoring the route. ① Press the SWING button. ② Press Number 1 or 2 to activate the Swing mode. - Number 1 : Commands the camera to pan while moving between 2 locations. - Number 2 : Commands the camera to tilt while moving between 2 locations. • To pause Swing, move the joystick. 8.
Setting Up Controller Environment Setting Up Controller Environment 2. Controller Main Setup 1. PTZ Setup ① Press 2 on the number pad. ② Hold down the SET button to enter the controller’s ① Press 1 on the number pad. ② Hold down the SET button to enter the PTZ SETUP MAIN SETUP mode. mode. ③ Enter the 4-digit password. (Default Password: 0000) ④ A fter changing the settings, select in the ③ Enter the 4-digit password.
Setting Up Controller Environment 2-4. Sleep Setting Up Controller Environment 2-8. Password ■ If no joystick or button input is detected for a set duration, the LCD screen turns itself off and enters Sleep mode. ■ Enables changing the controller password. 2-9. Factory Set 2-5. Buzzer ■ Turns the sound of controller buttons on or off. ■ Resets the controller’s current settings to the factory release default values and optimizes the joystick calibration. 2-6.
Troubleshooting Setting Up Controller Environment ● If the power is not turned on 3. Joystick Calibration ▶ Please check if the controller is connected to the power adapter. ① Press 3 on the number pad. ② Hold down the SET button to enter the Joystick Calibration mode. ③ At each option, move the joystick as far as you can, and then press the ENT button to calibrate. ● If the joystick does not move, or the controller buttons are not pressed ▶ There may be a problem with the controller board.
Product Specifications Product MEMO SPC-1010 LCD Display 16 x 2 Character LCD Speed Control Joystick (3-axis Twist Zoom) Samsung Techwin PTZ Dome PTZ Dome Compatible Hardware Zoom Camera SCZ-3430/2430/3370/2370/3250 SDZ-375/370 Receiver SRX-100B Control Capacity Communications SAMSUNG-T, SAMSUNG-E, PELCO-D/P, Panasonic, Vicon, AD, Honeywell Up to 255 Cameras (Suitable for Mid-, Large-size System) Standards RS-485 / RS-422 (Remote Control: 1km Distance) Transfer Speed 2,400 ~ 57,600bps Vo
MEMO PTZ CONTROLLER 22 User Guide MEMO PTZ CONTROLLER 23 User Guide
SALES NETWORK • AMSUNG TECHWIN CO., LTD. S Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400 TEL: +82-70-7147-8740~60, FAX: +82-31-8018-3745 • AMSUNG TECHWIN AMERICA Inc. S 1480 Charles Willard St, Carson, CA 90746, UNITED STATES Tol Free : +1-877-213-1222 FAX : +1-310-632-2195 www.samsungcctvusa.com • AMSUNG TECHWIN EUROPE LTD.