Index Main Page Safety Precautions Features Safety Precautions Exterior During Installation System Requirements During Operating Features Others Regulatory Installing DVD±R/RW Drive and Connecting Cables Installing Software and Confirming The Installation Installing Drive Software Setup Connecting Cables Firmware Upgrade Confirming the Installation of DVD±R/RW Installing the MS-DOS device driver How To Use The DVD±R/RW Drive Deleting Utilities How to Use the Drive When the on/off Light Bli
Safety Precautions This symbol indicates explanations about extremely dangerous matters. If users ignore this symbol and handle the device the wrong way, serious injury or death could result. This symbol indicates explanations about dangerous matters. If users ignore this symbol and handle the device the wrong way, damage to home or property could result. Important to read and understand at all times Do not disassemble Always make sure that the disc does not have a crack before use.
During Installation Do not drop the drive, and protect it from severe shocks. - It can damage the drive or cause it to malfunction. Do not place the drive in direct sunlight. Avoid low or high temperature environments. Avoid high-humidity environments.
During Operating Handle with caution to prevent damage from external shock. Do not drop the drive, and protect it from severe shocks. - It can damage the drive or cause it to malfunction. Do not move the drive while in operation and do not attempt to open the disc tray by force. Make sure to close all working programs before attempting to open the tray and always use the open/close button. Do not insert a pin into the emergency opening while in operation.
Others Never allow food particles or foreign substances to enter the drive casing. To protect against the risk of fire, do not spill such liquids as alcohol and benzene on the drive. Do not disassemble, attempt to repair or modify the device without express approval as directed in the manual. - To reduce the risk of damage, electric shock, and fire.
Regulatory Safety Approval Regulation Name Country Remark UL USA UL1950 CSA Canada CSA950, CAN/CSA-C22.2, NO.950-95 TUV Germany EN60950+ALL, EN60825-1 : 1994+ALL CE EU IEC60825-1 : 1994+All, EN60950 : 1992+A4 CB Certificate World IEC60825, IEC60950 DHHS USA DHHS RULES 21 CFR CHAPTER 1, SUB CHAPTER J GOST Russia EMC Compliance Regulation Name Country Remark MIC Korea EMI Class B BSMI TAIWAN CNS 13438(6357), 86.05.
Exterior DVD±R/RW Drive, screw, I/F cable, and audio cable Blank discs: DVD-R, and DVD+R Software Programs: Nero Express 6.0, WinDVD Creator, WinDVD Recorder, DVD Copy, In CD, DirectX 9.0, Acrobat Recorder 5.0 We recommend that you use cable that comes with the purchase of the drive for stable performance.
System Requirements You need to have an IBM-compatible PC with the following specifications. Item OS Description Microsoft Windows 98/2000/Me/XP(SP 1.
Features Versatile Multimedia Features DVD-RW: Read/Write/Rewritable DVD+RW: Read/Write/Rewritable CD+RW: Read/Write/Rewritable DVD-R: Read/Write DVD+R: Read/Write CD+R: Read/Write Supports Read (playback) for various types of discs See table below for details Disc Type CD Writable Rewritable Read CD-Stamp × × O CD-R O × O (O) O O × × O 4.7GB (FOR GENERAL Ver 2.0) O × O 4.7GB (FOR AUTHORING : Disc-at Once mode) × × O 3.95GB (FOR AUTHORING : Disc-at Once mode) × × O 4.
Features Ultra Speed CD-RW DISC(24X higher) does not support Reading / Recording. We recommend using the 'Recommended Disc Types'. When you use the other disc, may affect Reading / Recording of the data.
Installing Drive 1. Turn the PC off. 2. Open the cover as shown in the picture. 3. If necessary, attach the support devices on both sides of the drive - The support devices are PC accessories. Purchase a pair if necessary. 4. Insert the DVD±R/RW Drive after removing the plate as below - If you cannot remove/insert the plate smoothly, use the floppy disc slot instead.
Connecting Cables Connecting the Power Cable Hold the power cable (with four pins) in the power box within the computer with the cutoff edges( facing up and connect it to the power port in the back of the DVD±R/RW Drive ) 1 +5V DC A - Cutoff edges 2 Ground 3 Ground 4 +12V DC Improperly connected power cable may cause malfunction. Check the direction of the power cable and the cutoff edges before connecting the cable.
a : Slave Drive (Select the SL jumper) b : HDD c : MotherBoard When you use two E-IDE cables Connect the cable to MA in the Master/Slave port in the back of the DVD±R/RW Drive.
c : HDD d : Motherboard e : Primary 1 f : Secondly 1 Connecting the Jumper to the Master/Slave Port Connect the jumper to the slot in the back of the DVD±R/RW Drive. When you connect the jumper to MA (Master), the drive runs as the master, and when you connect it to SL (Slave), the drive runs as the slave. When you connect it to CS (CSEL), you can control the device using the host interface signal CSEL. (Connection to MA is recommended.
Software Setup 1. Insert the CD provided with the DVD±R/RW Drive to install the device program. The program runs automatically. If the automatic start fails, find the setup.exe file in the CD-ROM drive folder using Windows Explorer and double-click it. 2. Click [Install All Softwares Driver ] Once the installation process begins, follow the instructions. 3. Check [Yes, I want to restart my computer now] and click [Finish]. Use the DVD±R/RW Drive after rebooting the system.
Fimware Upgrade 1. Go to http://samsung-ODD.com 2. Click Firmware on the menu bar (in the upper right-hand corner).
Confiming Confirming Using [Device Manager] Windows 98/Me 1. Click [Start] - [Settings] - [Control Panel] - [System] 2. Click on the [Device Manager] tab in the System Properties window. 3. Click Disc Drive and CD-ROM in the Device Manager window. 1 & 2 in the picture in the left appear if the driver is installed properly. Windows 2000 1. Click [Start] - [Settings] - [Control Panel] - [System] 2. Click on the [Hardware] tab in the System Properties window and then click on the [Device Manager] tab. 3.
Installing the MS-DOS device driver Automatic Setup The device driver is located in the 'Dos_driver' folder of the CD which is provided with the DVD±R/RW Drive 1. Insert the CD provided with the DVD±R/RW Drive and open the 'Dos_driver' folder. 2. Run the CDSETUP.EXE file in the 'Dos_driver' folder. 3. When Setup is successfully completed, click 'OK' button or press the 'Enter' key. 4. Reboot the computer.
How to Use the Drive When the On/Off light is Green, do not turn the PC off or remove the DVD±R/RW Disc as it may cause damage in the drive. How to Use the Drive DVD-R Disc and Other Discs You can use 8cm or 12cm discs. The drive cannot read the disc properly if any part of the disc is place outside the tray guiding line. How to Use a Vertically Installed Drive This drive can be installed vertically. DVD-R Disc and Other Discs You can use only the 12cm discs.
When the on/off Light Blinks This part of the manual is to prevent damages or data loss. Read carefully and use the device properly.
How2 to Use DVD-R and Other Discs With the DVD±R/RW Drive, you can write data on a DVD-RW disc using the Nero Express and overwrite data using the In CD. You can also write data on a DVD-R disc using the Nero Express. Unauthorized copying of DVD or software titles is illegal and the individuals that make illegal copies will be held responsible for any copyright infringement. Using low-quality discs may lengthen the recording time or not supporing due to reduction in double speed.
Deleting Utilities Click [Start] - [Setting] - [Control Panel] - [Add/Remove Programs] and a window as shown below appears. [ Windows 98 / Me ] Click [Add / Remove] button to remove Software. [ Windows 2000 ] Click [Add / Remove] button to remove Software. [ Windows XP ] Click [Add / Remove] button to remove Software.
Cleaning the Drive This part of the manual is to prevent damages or data loss. Read carefully and use the device properly. Turn the PC off and pull out the drive. Remove any foreign objects from the surface of the drive using soft cloth. Do not use benzene, paint thinner, or any other solvents.
Storing the Disc This part of the manual is to prevent damages or data loss. Read carefully and use the device properly. Storing the cartridge-less other discs: Do not place it under the direct sunlight. Place it so that it sits on its side on a flat surface. Do not scribble or place a label on the disc. Handle the disc with caution to prevent damage from external shock. Do not expose it to severe temperature fluctuations. (Exposure to such environment may cause congealing.
Cleaning the Other Discs This part of the manual is to prevent damages or data loss. Read carefully and use the device properly. Do not touch the surface of the disc. Place your fingers on the edge of the disc to hold. Clean the disc lightly with soft cotton cloth, starting from the center and move to the edge of the disc. Use only disc cleaning liquids. Do not use benzene, paint thinner, or any other solvents.
Troubleshooting Problem The tray won't open. Meaning / Solution See if the PC on. Make sure the power cable within the PC is connected properly. If the tray still won't open with the power on, turn the power off and insert a pin(paper clip) into the emergency hole to open. The tray won't close. Make sure the disc has been inserted properly. The PC is not working properly. See if the jumper(s) is properly connected to the Master/Slave Selection port. See if the drive is properly connected to the PC.
Product Specifications SR-W04B Category DVD±R/RW Drive DISC Interface Support Detection Time Data Transfer Speed Usable DiscsNote) DVD :DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-ROM, DVDVideo CD: CD-R, CD-RW, CD-ROM, CD-Audio, CD-ROM XA, Photo CD, CD-I(FMV), Video CD, CD Extra, CD-Text Disc Diameter 120mm or 80mm Interface Port ATA/ATAPI (E-IDE) PIO mode PIO Mode 4: 16.6MB/sec DMA mode Ultra DMA Mode 2: 33.
Software Software Programs Nero Express 6 (CD/DVD Recording Software) WinDVD Creator (Editing & Authoring Software) WinDVD Recorder (Media Player & Recoder Software) DVD Copy (Disk Copier Software) Acrobat Reader 5.0 : Acrobat Reade lets your read the online documentation in PDF format as included. DirectX 9.0 : Software program required to use Softwares. Installing The Software 1. In Windows98/ME/2000/XP, close all programs and insert the software CD into your CD-ROM drive or DVD±R/RW Drive. 2.
Nero Express 6 www.Nero.com Features Superb Operability Easy-to-use Wizard Using the Wizard that appears when you first start the program, even a beginner can make a CD or a DVD in a simple and easy way. Simply follow the step-by-step instructions the Wizard provides. User-Friendly Layout Because the program uses the familiar Microsoft Windows Explorer layout, allowing easy and intuitive use of the functions, the user can easily create a CD or a DVD.
Nero Express 6 HDD Backup Function : Follow the easy-to-follow instructions to quickly and easily backup even large-capacity hard disc drives. Creating a "My Favorites" CD : You can create an audio CD with your favorite songs from different audio CDs. This feature is equipped with the "regularization" function that standardizes the volume level of the songs on the CD.
WinDVD Creator www.Intervideo.com Features Captures Captures audio or video data from digital cameras, digital camcorders, TVs or VCRs. Editing & Authoring Allows adding different effects to the captured/stored video clips, still pictures or audio data by a simple process of pressing a few buttons. Also allows video editing and title creation.
WinDVD Recorder www.Intervideo.com Features Simple Operation & A Wide Variety Of Design Features Create A DVD Video Presentation With A Few Simple Mouse Clicks You can create a DVD video presentation by drag-and-dropping files into the B's DVD main window. This way, you can make even complex video presentations in a few easy and simple steps. Use A Variety Of Templates To Make Menu Layouts You can choose a background from different styles of templates, including "Metallic" and "Pastel.
DVD Copy www.Intervideo.com Features Simple Operation & A Wide Variety Of Design Features Create A DVD Video Presentation With A Few Simple Mouse Clicks You can create a DVD video presentation by drag-and-dropping files into the B's DVD main window. This way, you can make even complex video presentations in a few easy and simple steps. Use A Variety Of Templates To Make Menu Layouts You can choose a background from different styles of templates, including "Metallic" and "Pastel.
