The expert for robots in your home With one click to the online shop myRobotcenter.eu myRobotcenter myRobotcenter.co.
Robot vacuum cleaner User manual SR10J50✴✴✴ Series • Before operating this unit, please read the instructions carefully. • For indoor use only.
Installation Installation Power of the charger must be on at all times. Power lamp (Red) Install it in a place without obstacles and danger of falling. About 0.5 m Installation About 0.5 m About 1 m NOTE • Install the charger in a place where the floor and wall are level. • Install the charger along the grain of wooden floors. • If the power switch is off, the robot vacuum cleaner will not charge even if it is docked on the charger. • Always turn on the power of the charger.
Accessories Batteries [AAA type (Option)] User manual Spare filter (Option) Cleaning brush Virtual guard (Option) Installation Remote control (Option) 13
Charging It takes approximately 120 minutes to completely charge when charging for the first time after purchase and can be used for approximately 90 minutes. Charging lamp during charging (green) Installation WARNING Rated input voltage of this product is 220 - 240 V~. 1 Turn on the power switch on the bottom. You must turn on the power switch to turn on the robot vacuum cleaner. 2 Manually charge the robot vacuum cleaner by placing it on the charger.
Automatic charging When the battery indicator blinks during cleaning, the robot vacuum cleaner will return to the charger to charge itself automatically. Installation Recharge You can command the robot vacuum cleaner to recharge at the charger while it is in cleaning process. Low battery (Lo) Manually charge the robot vacuum cleaner by placing it on the charger. Steps to take if recharging is not being executed.
Installing the virtual guard (Optional) Infrared ray from the Virtual guard will restrict the robot vacuum cleaner from approaching certain areas. Virtual guard Installation .5 m m2 u im Min The distance of virtual wall is 2.5 m at minimum and may differ depending on surroundings and movement status of the robot vacuum cleaner. Power lamp (Red) will blink. 1 Press the Power button to turn it on. 2 Install the Virtual guard where you want to restrict the robot vacuum cleaner’s entrance.
Part name of the virtual guard Power button Robot vacuum cleaner detection sensor Power lamp Power on: Red lamp blinks Power off: Lamp is off Installation Distance detection sensor (Infrared ray sensor) Battery cover Inserting batteries Batteries for the Virtual guard must be purchased separately. 1 Open the battery cover of the Virtual guard by pressing the locking tab and lift it up. 2 Insert the batteries (D type) as shown in the illustration (check the +, - polarity).
Operations Using the robot vacuum cleaner You must turn on the power switch before using the robot vacuum cleaner. Turning the power on/off Turn on/off the power switch on the bottom of the robot vacuum cleaner. WARNING • When the robot vacuum cleaner is not used for 10 minutes, power will turn off automatically. Operations Using auto clean mode The robot vacuum cleaner moves and cleans automatically until it cleans an entire space once.
Selecting cleaning mode Cleaning mode How to select Displayed icon Press once Auto clean Press twice Spot clean Press 3 times Max clean Operations Press 4 times Manual clean ❇ Direction control can be done only by the remote control. Press 5 times Edge clean ❇ When the robot vacuum cleaner is being charged, you can only select the Auto clean, Max clean or Edge clean mode.
Cleaning method for each mode Auto clean Spot clean Cleans a localized area intensely. It can be used to clean bread or cookie crumbs. Max clean Manual clean Cleans until the battery is depleted. You can move the robot vacuum cleaner with the remote control to clean the desired spot. Operations Edge clean Cleans the corners by reaching to them as close as possible. 20 About 1.5 m Cleans automatically until an entire space is cleaned once. About 1.
05 Point cleaning Only available with A type remote control 40 cm You can use the remote control to point and clean the desired spot while the robot vacuum cleaner is in cleaning process. • Point the red light on the floor within 40 cm around the robot vacuum cleaner’s location. • Press and hold the Point cleaning button to move the red light to the desired spot. The the robot vacuum cleaner will follow the light while cleaning.
Name of each part 01 04 Top 05 01 02 03 04 05 06 07 08 02 03 05 06 06 07 08 01 04 02 02 01 01 03 06 09 07 08 Bottom 01 02 03 04 05 06 07 08 09 Cliff sensor Side brush Charge pin Roller Driving wheel Battery cover Power brush Power brush cover Power switch Operations 05 Quick Empty cover (Option) Dustbin button Dustbin Display panel Remote control sensor Obstacle sensor Virtual guard sensor (Option) Bumper sensor Display panel 01 03 02 04 09 05 06 07 08 11 12 10 13 01 02 03 04 05 0
Maintenance Cleaning and maintaining You must turn off the power switch before cleaning the robot vacuum cleaner. Cleaning the dustbin Clean the dustbin if there’s too much dust in the dustbin.
Emptying the dustbin (Quick Empty) Use the Quick Empty cover for emptying the dustbin easily.
Cleaning the power brush 1 Remove the dustbin 2 Remove the power brush cover 3 Remove the power brush 4 Clean the power brush 5 Reassemble the power brush 6 Reassemble the power brush cover Maintenance 29
Cleaning the side brush Clean the side brush if there’s foreign matter on the brush. 1 Dip soft cloth into warm water R R R 2 Wrap the side brushes with the cloth for about 10 seconds and then wipe it If hair or string is caught between the main unit and the side brush, follow the below steps.