SR8850 SR8855 Robotic Vacuum Cleaner User Manual ✻ Before operating this unit, please read the instructions carefully. ✻ For indoor use only. imagine the possibilities Thank you for purchasing a Samsung product. To receive a more complete service, please register your product at www.samsung.
Safety information SAFETY INFORMATION WARNING WARNING • Before operating the appliance, please read this manual thoroughly and retain it for your reference. • Because these following operating instructions cover various models, the characteristics of your vacuum cleaner may differ slightly from those described in this manual. CAUTION/WARNING SYMBOLS USED WARNING CAUTION Indicates that a danger of death or serious injury exists. Indicates that a risk of personal injury or material damage exists.
Safety information IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should be observed, including the following: READ ALL INSTRUCTIONS BEFORE USING YOUR ROBOTIC VACUUM CLEANER. Unplug from outlet when not in use and before conducting maintenance. WARNING: to reduce the risk of fire, electric shock, or injury: GENERAL • Use only as described in this manual. • Do not operate the robotic vacuum cleaner or charger if it has been damaged in any way.
Safety information ROBOTIC VACUUM CLEANER • Do not pick up hard or sharp objects such as glass, nails, screws, coins, and etc. • D o not use without a filter in place. When servicing the unit, never put fingers or other objects into the fan chamber in case the unit accidentally turns on. • Do not put any objects into openings. Do not use with any openings blocked; keep openings free of dust, lint, hair, and anything that may reduce air flow.
Contents Safety information 02 Product Features 06 07 10 11 Power related Before use In use Cleaning and maintenance 13 Product Features 13 assembling the cleaner 15 OPERATING THE CLEANER 20 maintain tools and filter 36 troubleshooting 43 Product specification 46 15 Components 16 Name of each part 20 20 20 21 22 23 24 25 27 27 28 29 30 31 32 33 34 35 Installing robotic vacuum cleaner Installation order Turning the power switch on or off Installing the charger Charging About the battery Se
Safety information Power Related WARNING Do not bend the power cord forcefully or place a heavy object on it that could break it. - This may result in fire or electric shock. WARNING Make sure to remove any dust or water from the power plug. - Failing to do so may result in a malfunction or electric shock. WARNING Do not pull the power plug by the cord or touch the plug with wet hands. - This may result in fire or electric shock. WARNING Do not use multiple plugs in a single socket.
Safety information Before Use CAUTION CAUTION CAUTION CAUTION CAUTION 01 Safety information CAUTION Before activating the robotic vacuum cleaner, make sure that the dust bin is assembled. - If the dust bin is not inserted, robotic vacuum cleaner will not operate. Never use robotic vacuum cleaner in locations with combustible material such as: - Locations with candles or desk lamps on the floor. - Locations with unattended fires (fire or embers).
Safety information Before use CAUTION CAUTION CAUTION CAUTION CAUTION CAUTION CAUTION Remove small objects or brittle items from the area to be cleaned in advance. - Make sure to clear any objects before cleaning. - Make sure to remove fragile items such as china, glass objects, flowerpots, etc. - Robotic vacuum cleaner does not recognize coins, rings or other valuable items such as jewelry. Remove objects scattered on the floor before cleaning.
Safety information Before use CAUTION 01 Safety information CAUTION Install the charger in a location that can be easily accessed by the robotic vacuum cleaner. - If the charger is installed in a corner, this may cause extra movements and may disturb the automatic recharging process. Objects in front of the charger will prevent the robotic vacuum cleaner from auto-charging itself. - Clear the area. There should be no obstacles 0.5 m to the left and and within 1 m of the front.
Safety information In use CAUTION CAUTION CAUTION CAUTION CAUTION WARNING NOTE You cannot use the robotic vacuum cleaner on thick carpets. - This may result in problems with the robotic vacuum cleaner. - This may result in damage to carpets. Do not use the robotic vacuum cleaner on a table or other high locations. - This may result in damage when the unit accidentally drops. Robotic vacuum cleaner may bump into furniture such as chair legs, table legs, thin and long furniture, etc.
Safety information In use Robotic vacuum cleaner cannot completely clean locations that it cannot reach, such as corners, and spaces between sofas and walls. - Please clean these locations occasionally. NOTE Dust clusters may remain after cleaning, when the robotic vacuum cleaner fails to pick up dust clusters that were formed while cleaning. - In this case, sweep up the dust with another cleaning tool.
Safety information Cleaning and Maintenance WARNING When removing foreign substances, always use the cleaning brush after turning the Power Switch off. - Failing to do so may result in sudden operation of the unit and cause an injury or critical damage to the product. WARNING If the power cord is damaged, have it replaced by a qualified service engineer from the customer care center. - Failing to do so may result in fire or electric shock.
Product Features Convenient VIRTUAL GUARD Function You can confine the robotic vacuum cleaner to a particular section by using the Fence (virtual wall) mode or by cleaning several sections one by one using the Guard (virtual door) mode. • What is ceiling shape recognition (Visionary mappingTM)? This function recognizes the shape of the ceiling using the camera on top to identify the area to be cleaned and determines the best way to pass over and clean every section of the floor.
Product Features Auto Charging When the battery is low, the robotic vacuum cleaner is automatically guided to the charger to enable it to perform a quick auto charge. Edge-Cleaning Side ROTATING Brush The edge-cleaning side rotating brush cleans dust from the edges. Doorsill Crossing About 1.5cm Stair type Vertical type The robotic vacuum cleaner’s innovative driving system makes it possible for it to cross over doorsills with a height of about 1.5cm and clean all rooms.
Assembling the cleaner COMPONENTS Main Body ■ Remote Control ■ Charger (Station) 02 Assembling the cleaner ■ ■ Others Components (AAA-Type Batteries) User Manual / 2 Battery VIRTUALGUARD Spare Filter Remote Control Cradle Spare Edge-Cleaning Side Brush (2) Spare Power Brush Cleaning Brush Assembling the cleaner _15
Assembling the cleaner Name of each part [ Main unit ] Dust Outlet Operating Button Display Panel Camera VIRTUAL GUARD Sensor Obstacle Sensor Remote Control Sensor Obstacle Sensor VIRTUAL GUARD Sensor Bumper Sensor Front Dust Bin Eject Button Dust Bin Remote Control Sensor Dust Outlet Side Cliff Sensor Side Brush Driving Wheel Charge Pin Battery Cover Cliff Sensor Power Brush Power Brush Cover Power Switch Charge Pin Roller Driving Wheel Cliff Sensor Bottom 16_ Assembling the cleaner
Assembling the cleaner Name of each part [ Charger (Station) ] Charging Lamp Remote Control Holder Charge Pin Vents Catching Sill [ VIRTUAL GUARD ] Mode Lamp Distance Detection Sensor Main Body Detection Sensor Mode/Power Button Distance Control Switch ■ Installing the batteries Batteries are not supplied with the product. You have to purchase the batteries separately. Install the alkaline batteries (type D) before use. 1 2 3 Lift the cover of the VIRTUAL GUARD while pressing the locking tab.
Assembling the cleaner Name of each part [ Remote Control ] Power Recharging Auto Max Spot Directional Buttons Start/Stop (moving backwards is not supported.) ■ Manual Timer/Daily Edge Clock Installing the batteries Batteries are not installed in the remote control when purchasing the product. Install the batteries (type AAA) before use. 1 2 3 Lift the battery compartment cover at the back of the remote control, while pressing the locking tab.
Assembling the cleaner Name of each part [ Status Display Window] 7 4 3 6 ⓐ 8 ⓑ ⓒ 9 2 5 ⓓ 10 Display Part 1. Number Display - Shows the timer display, progress status, and error codes using numbers, letters and graphics. 2. Battery Level Indicator - Charging : Shows the charging progress in 3 steps. - In Use : Shows the battery charge level. The battery charge level is reduced by each level from FULL while operating. (When the battery is fully discharged, one level will flash to display “LO”.
Operating the cleaner Installing the robotic vacuum cleaner Instalation order 1. Turning the Power Switch on or off To use the robotic vacuum cleaner, you must turn on the Power Switch at the bottom of the main unit. 2. Installing the Charger To charge the robotic vacuum cleaner, you must first install the charger. Since the battery is discharged when the product is purchased, you must fully charge the battery before use. 3.
Operating the cleaner Installing the robotic vacuum cleaner Installing the charger Power Lamp Charging Lamp 03 operating the cleaner 1. Install the charger on a flat surface. 2. T here should be no obstacles 0.5m to the left and right and within 1 m of the front. 3. I nstall the charger in a location where it can be easily accessed by the robotic vacuum cleaner. 4. A rrange the power cord along the wall. 5.
Operating the cleaner Installing the robotic vacuum cleaner Charging When the product is initially purchased, the battery is fully discharged, and you must charge the robotic vacuum cleaner manually. Power Lamp Charging Lamp Turn on the Power Switch at the bottom of the product. 1. A fter aligning the charge pins of the main unit with the charge pin of the charger station, press the main unit until you hear a “Recharging power” sound from the charger. - The Charging Lamp turns green. 2.
Operating the cleaner Installing the robotic vacuum cleaner About the Battery he robotic vacuum cleaner is powered by an environment-friendly Nickel Metal Hydride T (NiMH) rechargeable battery, and an over-charge prevention function guarantees an extended life time. ■ The battery warranty period is 6 months from the date of purchase. ■ When purchasing a battery, ask the customer care center for the genuine part symbol ( ) and model number before purchasing it.
Operating the cleaner Installing the robotic vacuum cleaner Setting the Time To use the Scheduled Cleaning and Daily Cleaning functions properly, setting the time is necessary. You can only set the time using the remote control. ■ You can only set the time using the remote control. Remote Control Suppose current time is 07:00 1 Enter the current “hour”. Blinks Blinks Decrease Increase 2 Enter setup mode. 3 Set the “hour”.
Operating the cleaner Installing the robotic vacuum cleaner Installing the VIRTUAL GUARD Mode Lamp Distance Detection Sensor Main Unit Detection Sensor Mode/Power Button Distance Control Switch 2 3 Distance Detection Sensor Button operations 1. Mode lamp operations - Fence (virtual wall) Mode: The red lamp flashes. - Guard (virtual door) Mode: The green lamp flashes. - Off : The lamp is turned off. 2.
Operating the cleaner Using Guard (virtual door) mode The VIRTUAL GUARD forms an invisible door that the robotic vacuum cleaner cannot cross until current room is completly cleaned. The VIRTUAL GUARD opens the invisible door when cleaning the of room is complete. Room 1 1. Select Guard (virtual door) mode using the Mode/ Power button. - The mode lamp flashes green. 2. Set the fence length using the distance control switch. 3. Install the VIRTUAL GUARD at the entrance of the room to be cleaned.
Operating the cleaner Using the robotic vacuum cleaner Starting/Stopping Cleaning You can run or stop all robotic vacuum functions. ach robotic vacuum function only runs when the Power E Switch is turned on. ■ hen the robotic vacuum is operating, press the ( ) W button to cancel the operation and select a function. 03 operating the cleaner ■ Turning the power on or off Turning the power on - Remote control : Press the [Power] button. - Main unit: Press the ( ) button.
Operating the cleaner Using the robotic vacuum cleaner Recharging You can have the robotic vacuum cleaner return to the charger to charge the battery by using the Recharging button. ■ hen the robotic vacuum cleaner is operating, press W the ( ) button to cancel the operation and press the Recharging button. 1. Press the Recharging button. - The main unit icon ( ) is turned on and the robotic vacuum cleaner will return to the charger. 2.
Operating the cleaner Using the robotic vacuum cleaner Auto Cleaning ■ I f cleaning begins when the robotic vacuum cleaner is docked with the charger station, the time to return to the charger is decreased since the robotic vacuum cleaner remembers its original position while moving. ■ I f the battery level becomes too low while cleaning, the robotic vacuum cleaner will automatically return to the charger station and resume cleaning after charging its battery.
Operating the cleaner Using the robotic vacuum cleaner Spot Cleaning You can conveniently clean a specific area that has a a lot of cookie crumbs, dust, and etc. ove the robotic vacuum cleaner to the location where you M want to perform a spot clean. Main unit button About 1.5m ■ About 1.5m Remote control button Configuration Sequence 1 Set the mode. ▶ 2time 2 Cancel the mode. While cleaning - In Spot cleaning mode, the robotic vacuum cleaner cleans an area with a length of 1.
Operating the cleaner Using the robotic vacuum cleaner Max Cleaning ■ I f cleaning begins when the robotic vacuum cleaner is docked with the charger station, the time to return to the charger is decreased since the robotic vacuum cleaner remembers its original position while moving. ■ I f the battery level becomes low while cleaning, the robotic vacuum cleaner automatically returns to the charger station and resumes cleaning after charging the battery.
Operating the cleaner Using the robotic vacuum cleaner Manual Cleaning You can move the robotic vacuum cleaner to clean a particular location directly by using the remote control. ■ ove the robotic vacuum cleaner to the location where you M want to perform manual cleaning. ■ You can manually clean using the remote control only. Main unit button Remote control button Configuration Sequence 1 Set the mode. ▶ 4time 2 Cancel the mode.
Operating the cleaner Using the robotic vacuum cleaner EDGE CLEANING The robotic vacuum cleaner will move by itself and automatically clean the house until cleaning is completed once. ■ I f cleaning begins when the robotic vacuum cleaner is docked with the charger station, the time to return to the charger is decreased since the robotic vacuum cleaner remembers its original position while moving.
Operating the cleaner Using the robotic vacuum cleaner Scheduled Cleaning You can schedule robotic vacuum cleaner to start cleaning from a particular time. ■ cheduled cleaning is only performed when robotic S vacuum cleaner is docked with the charger station. Main unit button Remote control button Configuration Sequence 1 Enter Scheduled Cleaning mode and confirm that the configured time is correct. (Example) The current time: 07:00 a.m. The desired cleaning start time: 09:30 a.m.
Operating the cleaner Using the robotic vacuum cleaner Setting Daily Cleaning You can schedule the cleaning robot to start cleaning everyday from a particular time. aily cleaning is only performed when the cleaning robot D is docked with the charger station. Main unit button Remote control button Configuration Sequence (Example) The current time: 07:00 a.m. 1 Enter Daily Cleaning mode and confirm that The desired cleaning start time: 09:30 a.m. the configured time is correct.
Maintain tools and filter Cleaning the robotic vacuum cleaner Please keep the cleaning and maintenance methods in mind hen the Power Switch is damaged, please contact W the service agent so that it does not cause any accidents. ■ Do not use any means or mechanical devices not installed by the manufacturer that could accelerate the deformation of the robotic vacuum cleaner. ■ ■ lways turn off the power switch A at the bottom of the main unit before cleaning the robotic vacuum.
Maintain tools and filter Cleaning the robotic vacuum cleaner Emptying Dust Quickly ■ ou can easily empty the dust bin using a normal vacuum Y cleaner, without separating the dust bin. 2. I f you hold the air inlet of the vacuum cleaner to the dust outlet, it will vacuum the dust directly from the dust bin. Cleaning the Dust Bin and the Filter First, empty the dust bin before cleaning it. hen separating the dust bin, take care not to spill the W dust out of the dust bin.
Maintain tools and filter Cleaning the robotic vacuum cleaner 4. Wipe the dust from the filter and the dust bin. ✽ You can wash them with water. 5. Install the filter into the dust bin. - Make sure that the grid pattern of the filter is facing downwards. It cannot be installed in the wrong direction. 6. Close the dust bin cover and install it into the main unit.
Maintain tools and filter Cleaning the robotic vacuum cleaner Cleaning the Power Brush You must turn off the Power Switch at the bottom of the main unit before cleaning the robotic vacuum. 04 Maintain tools and filter ●B ecause the dust in the dust bin may come out, CAUTION separate the dust bin first before cleaning the power brush. 1. S eparate the dust bin by pressing the Dust Bin Eject (PUSH) button. 2.
Maintain tools and filter Cleaning the robotic vacuum cleaner 6. A fter inserting the 3 tips at the top of the cover, push the other end in until it “clicks” into place. ●T o prevent the robotic vacuum cleaner from becoming clogged, be careful not to CAUTION vacuum tooth picks or cotton swabs. ● When removing foreign substances becomes difficult, contact a customer care center. ●B ecause the power brush vacuums the dust on the floor, long strings or hair can become wrapped around the brush.
Maintain tools and filter Cleaning the robotic vacuum cleaner Cleaning the Edge-Cleaning Side rotating Brush You must turn off the Power Switch at the bottom of the main unit before cleaning the robotic vacuum. 04 Maintain tools and filter 1. Check whether the side rotating brush is bent or whether there are any foreign substances stuck on the brush. 2. W earing rubber gloves, wrap the side rotating brush with a cloth using hot water for about 10 seconds and wipe it on the cloth. 3.
Maintain tools and filter Cleaning the robotic vacuum cleaner Cleaning the Driving Wheel You must turn off the Power Switch at the bottom of the main unit before cleaning the robotic. ■ I f the robotic vacuum cleaner suddenly starts to zigzag, there may be foreign substances stuck on the driving wheel. 1. W hen cleaning the driving wheel, place a soft cloth on the floor and flip the main unit, placing it down carefully. 2.
Troubleshooting Checklist before SVC Calls Symptom • Is the Power Switch • Turn on the Power Switch. turned on? • Is cleaning mode ( ) in the display panel turned on? • Is the battery level flashing only one level and is ‘LO’ displayed in the display panel? • Robotic vacuum cleaner will not Robotic vacuum cleaner stopped operating while cleaning. The suction power is weak while cleaning. Measure to Take • Install the dust bin. • Press the ( ) button.
Troubleshooting Checklist before SVC Calls Symptom Robotic vacuum cleaner cannot find the charger. Checklist plug of the charger is plugged correctly into the outlet. • If there are any obstacles within a range of about 1m in front of the charger and about 0.5m range to the left and right of the charger, you should remove the obstacles. • If there are any foreign substances on the change pin, wipe them off with a dry towel.
Troubleshooting Troubleshooting for Error Codes Cause SOLUTION • Robotic vacuum cleaner is • Turn off the Power Switch at the bottom • • • • • caught, stuck or trapped while navigating. A foreign substance (string, paper, toy etc.) is caught in the power brush. A foreign substance (string, paper, toy etc.) is caught in the left driving wheel. A foreign substance (string, paper, toy etc.) is caught in the right driving wheel. Check bumper sensor.
Product specification 93 mm (Height) 355 mm (Length) 355 mm (Width) Main Body 122 mm (Height) 161 mm (Length) Charger(Station) 46_ Product specification 275 mm (Width)
Product specification Classification Electrical Specifications Detail Diameter 355mm Height 93mm Weight 4.0kg Power voltage AC220-240V~, 50-60Hz Charge power consumption 50 W Main unit power consumption 40 W Battery specifications 14.4V / 2,000 mA Dust bin capacity About 0.
Contact SAMSUNG WORLD WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. Country AUSTRALIA Customer Care Center ☎ Web Site 1300 362 603 www.samsung.com HONG KONG (852) 3698-4698 www.samsung.com/hk www.samsung.com/hk_en/ MALAYSIA 1800-88-9999 www.samsung.com SINGAPORE 1800-SAMSUNG (7267864) www.samsung.com Code No. DJ68-00518X REV(0.
