Quick Start Guide

ManualsBrandsSamsung ManualsNetworkIndustrially Hardened 11 Port Managed Ethernet Switch

QSG_SWT-F0803MG 08/12/19 PAGE 1

QUICK START GUIDE SWT-F0803MG SERIES

QUICK START GUIDE

SWT-F0803MG Series

Environmentally Hardened Managed Ethernet Switch

3 SFP + 8 Electrical Ports with 60 Watt PoE

The SWT-F11MGHP is composed of the SWT-F0803MGHP240 Switch and

PWR-DR48480 Power Supply.

The SWT-F0803MG series has three 100/1000Base-FX SFP ports and eight

10/100Base-TX ports. Two of the SFP ports support 2.5 Gbps SFPs for high-speed

communication in bandwidth-intensive applications. All SFP ports utilize SFP

modules for fiber and connector type and distance. The IEEE802.3-compliant unit

offers multiple Ethernet redundancy protocols (MSTP/RSTP/STP/ERPS (G.8032))

which protect your applications from network interruptions or temporary

malfunctions by redirecting transmission within the network. The switch provides

advanced IP-based management that can limit the maximum bandwidth for each

connected IP device, allowing the user to adjust usage. The switch provides

eight electrical ports supplying Power over Ethernet (PoE). Four of the eight PoE

ports can support up to 60 watts of PoE power per port, while the other four ports

support up to 30 watts of power per port. All PoE ports are IEEE802.3af/IEEE802.3at

compliant.

This guide serves the following

Model Names:

SWT-F0803MGHP240

Summary of content (16 pages)

PAGE 1
QUICK START GUIDE SWT-F0803MG Series QUICK START GUIDE SWT-F0803MG Series Environmentally Hardened Managed Ethernet Switch 3 SFP + 8 Electrical Ports with 60 Watt PoE This guide serves the following Model Names: SWT-F0803MGHP240 The SWT-F11MGHP is composed of the SWT-F0803MGHP240 Switch and PWR-DR48480 Power Supply. The SWT-F0803MG series has three 100/1000Base-FX SFP ports and eight 10/100Base-TX ports. Two of the SFP ports support 2.
PAGE 2
QUICK START GUIDE SWT-F0803MG Series Contents Regulatory Compliance Statement 3 Warranty 3 Disclaimer 3 Safety Information 4 Hardware Installation 5 Installing the Switch on DIN-Rail 5 Wall Mounting Installation 7 Hardware Overview 8 9 9 9 Software Configuration 10 Configuration by Web Browser 10 Setting an Initial Password 11 Using Switch CLI 12 Factory Default Procedure 16 QSG_SWT-F0803MG 08/12/19 PAGE 2
PAGE 3
QUICK START GUIDE SWT-F0803MG Series Regulatory Compliance Statement Product(s) associated with this publication complies/comply with all applicable regulations. Please refer to the Technical Specifications section for more details. Warranty Hanwha Techwin warrants that all products are free from defects in material and workmanship for a specified warranty period of 3 years from the invoice date. Hanwha Techwin will repair or replace products found by to be defective within this warranty period.
PAGE 4
QUICK START GUIDE SWT-F0803MG Series Safety Information »» Only service personnel can service the equipment. Please contact Technical Support. »» The equipment should be installed in locations with controlled access, or other means of security, and controlled by persons of authority. When operating at temperatures above 51º C, the equipment surfaces will be hot to the touch. Installation in restricted access location is required for this case.
PAGE 5
QUICK START GUIDE SWT-F0803MG Series Hardware Installation Installing the Switch on DIN-Rail Each switch has a DIN-Rail kit on the rear panel. The DIN-Rail kit affixes the switch to the DIN-Rail.
PAGE 6
QUICK START GUIDE SWT-F0803MG Series It is easy to install the switch on the Din-Rail: Mount Series on DIN-Rail Step 1: Tilt the switch and mount the metal spring to DIN-Rail. Step 2: Push the switch toward the DIN-Rail until you hear the spring snap into place .
PAGE 7
QUICK START GUIDE SWT-F0803MG Series Wall Mounting Installation Each switch has another installation method for users to fix the switch. A wall mount panel can be found in the package. The following steps show how to mount the switch on the wall: Mounting the switch on a wall Note: For drywall applications where no studs are available, use drywall anchors rated for 50 lbs or more. In order to prevent switches from being damaged, use appropriate hardware (not supplied) for securing the unit to the wall.
PAGE 8
QUICK START GUIDE SWT-F0803MG Series Hardware Overview 1 5 2 6 7 3 8 4 9 SWT-F0803MGHP240 Front Panel Call-out Description 1 1 × 100/1000Base-FX SFP Port 2 2 × 100/1000/2500Base-FX SFP Ports 3 Link/Activity LED Indicators for SFP Ports 4 8 × 10/100Base-TX RJ45 Ports 5 PoE LED Indicators 6 Alarm and Power LED Indicators 7 USB Console Port 8 Fault Relay 3-Pin Terminal Block Connector 9 Redundant Power 2-Pin Terminal Block Connectors QSG_SWT-F0803MG 08/12/19 PAGE 8
PAGE 9
QUICK START GUIDE SWT-F0803MG Series Power Supply For SWT-F0803MGHP240 Model, Power Supply must be 44 to 57 VDC @ 250W max. IMPORTANT SAFEGUARDS: A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.
PAGE 10
QUICK START GUIDE eries Software Configuration Attention: W hile installing and upgrading firmware, please remove physical loop connection first. DO NOT power off equipment while the firmware is upgrading! Configuration by Web Browser About Web-based Management An embedded HTML web site resides in the flash memory on the CPU board. It contains advanced management features and allows you to manage the switch from anywhere on the network through a standard web browser such as Microsoft Internet Explorer.
PAGE 11
SWT-F0803MG Series Setting an Initial Password Wisenet switches require a password to be set upon initial login using the CLI. Before you can sign in to the web GUI, a password must be set using the CLI. The CLI can be accessed using the USB port and terminal software or with an ethernet cable and telnet. If the password is lost, the unit must be restored to the factory default settings, following the procedure on page 315. Connect to the switch using the USB port or by ethernet.
PAGE 12
SWT-F0803MG Series Using Switch CLI About CLI Management Besides Web-based management, the switch also supports CLI management. You can use console or telnet to manage switch by CLI. CLI Management by Serial Console (115200, 8, none, 1, none) Before configuring the serial console, use a USB Male-A to USB Male-B cable to connect the Switches’ USB Console port to your PC’s USB port. Follow the steps below to access the console via USB cable using Windows Hyper Terminal.
PAGE 13
SWT-F0803MG Series Step 2. Input a name for new connection Step 3.
PAGE 14
SWT-F0803MG Series Step 4. The COM port properties setting, 115200 for Bits per second, 8 for Data bits, None for Parity, 1 for Stop bits and none for Flow control. Step 5. The Console login screen will appear. Use the keyboard to enter the Username and Password (use the same password as the Web Browser), then press “Enter”. If a password has not been set, a new password must be set before proceeding or logging in to the web GUI. Please refer to p.11.
PAGE 15
SWT-F0803MG Series CLI Management by Telnet You can use “telnet” or similar virtual terminal software to configure the switch via a network connection. Note that you may need to install the Telnet client in certain versions of Windows (Settings > Turn Windows Features on or off > Telnet Client). You can also use a 3rd party Telnet client, such as PuTTY. The default value is as below: IP Address: 192.168.1.1 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.1.
PAGE 16
SWT-F0803MG Series Factory Default Procedure Wisenet switches have a procedure to return the unit to factory default configuration, deleting the running & startup configuration. This is useful in cases where the configured password cannot be remembered and the "reload defaults" command can not be used. 1. Start with switch in the powered-off state. Locate the reset button on the left hand side of the unit. The reset button is located inside the 3rd hole from the bottom, as shown in the image below.