SyncMaster 591s / 591v / 793s / 793v / 783DF / 793DF / 793MB / 795DF / 795MB / 797DF / 997DF Ins tall drivers Ins tall programs
Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock Power When not used for extended periods of time, set your computer to a screen saver. z If the same image is present for long periods of time, Phosphor Burnt can be occured, or the screen may be blurred.
z This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. z This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. z An improper ground may cause electric shock or equipment damage. Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. z This may cause an electric shock or fire.
Installation Put your monitor in a location with low humidity and a minimum of dust. z Failure to do so may cause an electric shock or fire inside the monitor. Do not drop the monitor when moving it. z This may cause damage to the product or human body. Install the monitor base in a showcase or shelf so that the end of the base does not project beyond the showcase or shelf. z Dropping the product may cause damage to the product or personal injury. Set down the monitor carefully.
Clean When cleaning the monitor case or the surface of the CDT, wipe with a slightly moistened, soft fabric. Do not clean Flat monitor with water. Use a water-diluted mild detergent. (Some detergents contain significant amounts of alcohol-based solvents, which can damage (color change) or crack the monitor case. The antiglare/anti-static surface coating on the CDT may also be affected.) Dilute the detergent (1:10 ratio) with water before using. Do not spray water or detergent directly on the monitor.
Do not cover the vents on the monitor cabinet. z Bad ventilation may cause a breakdown or fire. Do not set a glass of water, chemicals or any small metal objects on the monitor. z z This may cause damage, electric shock or fire. If a foreign substance gets into the monitor, disconnect the plug and then contact a service center. For each hour of looking at the monitor, you should let your eyes rest for 5 minutes. z This will reduce eye fatigue.
Keep the monitor away from any magnetic substances. z This may cause discoloring or distortion of the image. Do not install the product on an unstable, uneven surface or a location prone to vibrations. z Dropping the product may cause damage to the product or personal injury. Using the product in a location prone to vibrations may shorten the lifetime of the product or may catch fire.
Hoidke monitor eemal mistahes magnetilistest esemetest. z Need võivad põhjustada värvi muutumist või moonutada kujutist. Ärge paigaldage seadet kõikuvale, ebatasasele pinnale või kohtadesse, kus esineb vibratsiooni. z Seadme kukkumine võib põhjustada vigastusi nii seadmele kui ka kasutajale. Seadme kasutamine kohtades, kus esineb vibratsiooni, lühendab toote kasutusiga ja võib põhjustada tulekahju.
SyncMaster 591s / 591v / 793s / 793v / 997DF /793DF 793MB / 795DF / 795MB / 797DF Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Unpacking Monitor and Stand (Some models include a stand attached.
Power Cord Signal Cable (Option) Stand Stand For Multimedia model (Option) Manual User Guide Cable Sound Cables(2each) Stand Multimedia Speaker Stand Front DC Power Cord
Menu button [ Adjust buttons [ Opens the OSD menu. Also used to exit the OSD menu or return to the previous menu. ] ] These buttons allow you to highlight and adjust items in the menu. Enter button [ ] Used to select the OSD menu. Power button Use this button for turn the monitor on and off. Power indicator This light glows green during normal operation, and blinks green once as the monitor saves your adjustments.
SyncMaster 591s / 591v / 793s / 793v / 783DF / 793DF / /997DF / 793MB / 795DF / 795MB / 797DF (The configuration at the back of the monitor may vary from product to product.) Power port Connect the power cord for your monitor to the power port on the back of the monitor. Signal Cable Connect the signal cable to the video port on your computer, video board, video card, or graphics card.
Bottom Signal Cable Connect the signal cable to the video port on your computer, video board, video card, or graphics card. Power port Connect the power cord for your monitor to the power port on the back of the monitor. Tilt/Swivel Base You can separate the base from the monitor.
SyncMaster 783DF Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Unpacking Monitor and Stand (Some models include a stand attached.
Stand Stand For Multimedia model (Option) Manual User Guide Cable Sound Cables(2each) Stand Multimedia Speaker Stand Front DC Power Cord
Menu button [ Adjust buttons [ Opens the OSD menu. Also used to exit the OSD menu or return to the previous menu. ] ] These buttons allow you to highlight and adjust items in the menu. Enter button [ ] Used to select the OSD menu. Power button Use this button for turn the monitor on and off. Power indicator This light glows green during normal operation, and blinks green once as the monitor saves your adjustments.
Power port Connect the power cord for your monitor to the power port on the back of the monitor. Signal Cable Connect the signal cable to the video port on your computer, video board, video card, or graphics card. See Connecting the Monitor for further information regarding cable connections. Bottom Signal Cable Connect the signal cable to the video port on your computer, video board, video card, or graphics card.
SyncMaster 591s / 591v / 793s / 793v / 783DF / 793DF / 793MB / 795DF / 795MB / 797DF / 997DF Setup-For Multimedia model | Multimedia Speaker Stand General | BNC Connectors (Option) General 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Connecting to a computer Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 2-2.
SyncMaster 997DF 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Connecting to a computer Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 2-2. Connecting to a new Macintosh Connect the monitor to the Macintosh computer using the D-SUB connection cable. 2-3.
1. Turn off your computer and unplug the power cord. 2. Connect the end of the signal cable to your computer's video port(video board, video card or graphics card). 3. Connect one end of the other sound cable to the Mic Input jack on your sound card or computer.Connect the other end of this cable to the Mic By-pass jack on the back of the monitor stand. 4. Plug the DC power cord from the stand into a nearby outlet. 5.
The base is detachable. Attaching and Removing the Base If your monitor was supplied with the base detached, attach the base as follows. Remove the twist-tie before attaching the base to the monitor.
Attaching the Base 1. 2. 3. 4. Place the monitor upside-down on a flat work surface. Align the tabs on the base with the corresponding slots on the bottom of the monitor. Press the base onto the monitor until the tabs are fully engaged in the slots. Push the base toward the front of the monitor until the release latch clicks into the locked position. * Do not bend the snap. Removing the Base 5. Squeeze and pull up on the release latch on the base. 6.
1. Insert CD into the CD-ROM drive. 2. Click "Windows XP/2000 Driver" 3. Choose your monitor model in the model list, then click the "OK" button. 4. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certified MS logo and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/. 5. Monitor driver installation is completed.
3. Click "Display" icon and choose the "Settings" tab then click "Advanced..". 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk".
7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certified MS logo and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/. 9. Click the "Close" button, then click "OK" button continually.
10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Click "Start" , "Setting" , "Control Panel". Double click the "Display" Icon.
Linux Operating System To execute X-Window, you need to make the X86Config file, which is a type of system setting file. 1. 2. 3. 4. 5. 6. 7. Press Enter at the first and the second screen after executing the X86Config file. The third screen is for setting your mouse. Set a mouse for your computer. The next screen is for selecting a keyboard. Set a Keyboard for your computer. The next screen is for setting your monitor. First of all, set a horizontal frequency for your monitor.
SyncMaster 591s / 591v Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. These buttons allow you to highlight and adjust items in the menu. Use to select the OSD menu.
Menu Description When OSD is not on the screen, push the button to adjust brightness. Contrast Menu Description When OSD is not on the screen, push the button to adjust Contrast.
Menu Description You can use the on-screen menus to change the brightness according to personal preference. Direct Access Feature : When OSD is not on the screen, push the button to adjust brightness. You can use the on-screen menus to change the contrast according to personal preference. A "Moiré" pattern can appear on your screen, looking like a series of concentric circles or arcs. To eliminate this pattern, use the horizontal moire adjustments.
Menu Description Play/Stop Color temperature is a measure of the 'warmth' of the image colors. (6500K / 9300K) Use to adjust the monitor color setting.(Red) Use to adjust the monitor color setting.(Green) Use to adjust the monitor color setting.(Blue) When you adjust the Brightness and Contrast after sRGB mode is selected, sRGB mode exits. Menu Description Follow these instructions to change the horizontal position of the monitor's entire display.
Follow these instructions to change the vertical size of the monitor's entire display. Adjust the pincushion setting when the sides of the display are bowed in or bowed out. Adjust the pinbalance setting when the sides of the display are bowed towards the left or right. Adjust the trapezoid setting when the top or bottom of the display is too large or small. Adjust the parallelogram setting when the display is leaning left or right.
SyncMaster 783DF Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. These buttons allow you to highlight and adjust items in the menu. Use to select the OSD menu.
Menu Description When OSD is not on the screen, push the button to adjust brightness. Contrast Menu Description When OSD is not on the screen, push the button to adjust Contrast.
Menu Description You can use the on-screen menus to change the brightness according to personal preference. Direct Access Feature : When OSD is not on the screen, push the button to adjust brightness. You can use the on-screen menus to change the contrast according to personal preference. A "Moiré" pattern can appear on your screen, looking like a series of concentric circles or arcs. To eliminate this pattern, use the horizontal moire adjustments.
Menu Description Play/Stop Color temperature is a measure of the 'warmth' of the image colors. (6500K / 9300K) Use to adjust the monitor color setting.(Red) Use to adjust the monitor color setting.(Green) Use to adjust the monitor color setting.(Blue) When you adjust the Brightness and Contrast after sRGB mode is selected, sRGB mode exits. Menu Description Follow these instructions to change the horizontal position of the monitor's entire display.
Follow these instructions to change the vertical size of the monitor's entire display. Adjust the pincushion setting when the sides of the display are bowed in or bowed out. Adjust the pinbalance setting when the sides of the display are bowed towards the left or right. Adjust the trapezoid setting when the top or bottom of the display is too large or small. Adjust the parallelogram setting when the display is leaning left or right.
SyncMaster 797DF Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. These buttons allow you to highlight and adjust items in the menu. Use to select the OSD menu.
Menu Description When OSD is not on the screen, push the button to adjust brightness. Contrast Menu Description When OSD is not on the screen, push the button to adjust Contrast.
Menu Description You can use the on-screen menus to change the brightness according to personal preference. Direct Access Feature : When OSD is not on the screen, push the button to adjust brightness. You can use the on-screen menus to change the contrast according to personal preference. A "Moiré" pattern can appear on your screen, looking like a series of concentric circles or arcs. To eliminate this pattern, use the horizontal moire adjustments.
Menu Description Play/Stop Color temperature is a measure of the 'warmth' of the image colors. The available range is between 5000 to 9300K. Use to adjust the monitor color setting.(Red) Use to adjust the monitor color setting.(Green) Use to adjust the monitor color setting.(Blue) When you adjust the Brightness and Contrast after sRGB mode is selected, sRGB mode exits. Menu Description Follow these instructions to change the horizontal position of the monitor's entire display.
Follow these instructions to change the vertical size of the monitor's entire display. Adjust the pincushion setting when the sides of the display are bowed in or bowed out. Adjust the pinbalance setting when the sides of the display are bowed towards the left or right. Adjust the trapezoid setting when the top or bottom of the display is too large or small. Adjust the parallelogram setting when the display is leaning left or right.
SyncMaster 997DF Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. These buttons allow you to highlight and adjust items in the menu. Use to select the OSD menu.
Menu Description When OSD is not on the screen, push the button to adjust brightness. Contrast Menu Description When OSD is not on the screen, push the button to adjust Contrast.
Menu Description You can use the on-screen menus to change the brightness according to personal preference. Direct Access Feature : When OSD is not on the screen, push the button to adjust brightness. You can use the on-screen menus to change the contrast according to personal preference. A "Moiré" pattern can appear on your screen, looking like a series of concentric circles or arcs. To eliminate this pattern, use the horizontal moire adjustments.
Menu Description Play/Stop Color temperature is a measure of the 'warmth' of the image colors. The available range is between 5000 to 9300K. Use to adjust the monitor color setting.(Red) Use to adjust the monitor color setting.(Green) Use to adjust the monitor color setting.(Blue) When you adjust the Brightness and Contrast after sRGB mode is selected, sRGB mode exits. Menu Description Follow these instructions to change the horizontal position of the monitor's entire display.
Follow these instructions to change the vertical size of the monitor's entire display. Adjust the pincushion setting when the sides of the display are bowed in or bowed out. Adjust the pinbalance setting when the sides of the display are bowed towards the left or right. Adjust the trapezoid setting when the top or bottom of the display is too large or small. Adjust the parallelogram setting when the display is leaning left or right.
SyncMaster 793s / 793v / 793DF / 793MB / 795DF / 795MB Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. These buttons allow you to highlight and adjust items in the menu. Use to select the OSD menu. MagicBright2™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching.
Menu Description When OSD is not on the screen, push the button to adjust brightness. MagicBright2™ SyncMaster 793MB / 795MB Menu MagicBright2™ Description Then push the MagicBright2™ button again to circle through available preconfigured modes.
Menu Description You can use the on-screen menus to change the brightness according to personal preference. Direct Access Feature : When OSD is not on the screen, push the button to adjust brightness. You can use the on-screen menus to change the contrast according to personal preference. A "Moiré" pattern can appear on your screen, looking like a series of concentric circles or arcs. To eliminate this pattern, use the horizontal moire adjustments.
Menu Description Play/Stop Color temperature is a measure of the 'warmth' of the image colors. (6500K / 9300K) Use to adjust the monitor color setting.(Red) Use to adjust the monitor color setting.(Green) Use to adjust the monitor color setting.(Blue) When you adjust the Brightness and Contrast after sRGB mode is selected, sRGB mode exits. Menu Description Follow these instructions to change the horizontal position of the monitor's entire display.
Follow these instructions to change the vertical size of the monitor's entire display. Adjust the pincushion setting when the sides of the display are bowed in or bowed out. Adjust the pinbalance setting when the sides of the display are bowed towards the left or right. Adjust the trapezoid setting when the top or bottom of the display is too large or small. Adjust the parallelogram setting when the display is leaning left or right.
Overview | Installation | OSD Mode | Uninstall | Troubleshooting Overview What is MagicTune™ ? Monitor performance can v ary due to the graphics card, host c omputer lighting conditions and other environmental factors . In order to get the best image on a monitor requires you to adjust it for your unique setting. Unfortunately, the manual controls av ailable to tune the image often prove to be c hallenging.
Overview | Installation | OSD Mode | Uninstall | Troubleshooting Installation 1. Ins ert the installation CD into the CD-ROM drive. 2. Click the MagicTune™ installation file. 3. Select installation Language, Click "Next". 4. When the InstallationShield Wizard window appears, click "Next." 5. Select "I agree to the terms of the license agreement" to accept the terms of use.
6. Choose a folder to install the MagicTune program. 7. Click "Ins tall." 8. The "Installationation Status" window appears.
9. Click "Finish." 10. When the installation is complete, the MagicTune 2.5 executable icon appears on y our desktop. Double -click the ic on to start the program. Magic tune ex ecution icon may not appear depending on specification of computer sys tem or monitor. If that happens, pres s F5 Key. 11. The following window appears if the installation is successful.
12. The following error message indicates that the system is using a video card that is not supported by MagicT une. Installationation Problems The ins tallation of MagicTune™ 2.5 can be affected by such factors as the v ideo card, motherboard and the network environment. See "Troubleshooting" if you have trouble during installation.
Overview | Installation | OSD Mode | Uninstall | Troubleshooting MagicTune allows for quick accurate tuning of the display with the ability to easily save and use monitor configurations that are best suited for you. z OSD mode may appear inconsistent with the explanation in guidance book depending on specification of each monitor. OSD Mode The OSD mode makes the adjustment of settings on all monitors easy.
Cancel not made any changes in the control window, clicking "Cancel" does not cause any actions. Picture Tab Definition Allows the user to adjust the screen settings to the desired values. i Brightness n j k l m n j MagicBright k l m j Contrast n k l m Brightnes s Makes the entire screen brighter or darker. The detailed data of the images in the dark areas can be lost if the brightness is not adjusted to the proper level. Adjust the brightness for best viewing conditions.
and graphics. 3. Game: For watching motion pictures such as a Game. 4. Entertain: For watching motion pictures such as a DVD or VCD. MagicBright™ z Less than 19" 1. Text: For documentations or works involving heavy text. 2. Internet: For working with a mixture of images such as text and graphics. 3. Entertain: For watching motion pictures such as a DVD or VCD. Color Tab Definition Adjusts the "warmth" of the monitor background or image color.
Image Tab Definition Adjusts the Position, Size and Rotation values. Geometry 1 i Rotation n j k l m n j Size k l m Geometry 2 j Pincushion k l m n j Position k l m n j Pinbalance n k l m n j Trapezoid n k l m j Parallelogram k l m Other j Moire n k l m n j Degauss n k l m j Sidepin Corner Top k l m j Sidepin Corner Bottom n k l m n j Pinbalance Corner Top k l m j Pinbalance Corner Bottom k l m n Adjusts the Position, Size and Rotation values.
z z Pinbalance Corner Top Pinbalance Corner Bottom Option Tab Definition You can configure MagicTune using the following options. Loads the Preferences Dialog Box. Preferences in use will have an "V" in the check box. To turn on or o ff any Preference, position the cursor over the box and click. Preferences z z Enable task tray menu . - To access the MagicTune menus, click the icon on the [task tray menu].
Help Visit the MagicTune website or click to open the Help files (User Manual) if you need any help installing or running MagicTune. The User Manual opens within a basic browser window. Asset ID Opens a monitor info window showing the manufacturing date of the monitor. Version Displays the version number of MagicTune.
Overview | Installation | OSD Mode | Uninstall | Troubleshooting Uninstall The MagicTune program can be removed only by using the "Add or Remove Programs" option of the Windows Control Panel. Perform the following steps remove MagicTune. 1. Go to [Task Tray] ' [Start] ' [Settings] and selec t [Control Panel] in the menu. If the program runs on Windows XP, go to [Control Panel] in the [Start] menu. 2. Click the "Add or Remove Programs" icon in Control Panel. 3.
Overview | Installation | OSD Mode | Uninstall | Troubleshootin g Troubleshooting Magic Tune may not work in case monitor is replaced or driver of graphic c ard is updated while Magic Tune is operating. If so, please restart the system. Check when MagicTune does not function properly. * MagicTune feature is found only on PC (VGA) with Window OS that supports Plug and Play.
SyncMaster 591s,591v Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom No images on the screen. I cannot turn on the monitor. Check List Solutions Is the power cord connected properly? Check the power cord connection and supply. Can you see " screen? Check the signal cable connection.
voltage wire near by? Is the voltage stable? The screen image can appear to shake or vibrate at a particular time of day due to low supply voltage. The screen image can also appear to shake or vibrate if there is a problem with the video card or the computer's main board. The screen shows strange colors or just black and white. The screen suddenly has become unbalanced. Is the screen displaying only one color as if looking at the screen through a cellophane paper? Check the signal cable connection.
2. Check if the computer beeps more than 3 times when booting. (If it does, request an after-service for the main board of the computer.) 3. If you installed a new video card or if you assembled the PC, check if the installed adapter (video) driver and the monitor driver. 4. Check if the scanning ratio of the video screen is set at 50Hz or 120 Hz. (Do not exceed 60Hz when using the maximum resolution.) 5.
This box appears during normal operation if the video cable becomes disconnected or damaged. 4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor. If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly.
SyncMaster 793s,793v,783DF,793DF,793MB,797DF Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom No images on the screen. I cannot turn on the monitor. Check List Solutions Is the power cord connected properly? Check the power cord connection and supply. Can you see " screen? Check the signal cable connection.
voltage wire near by? Is the voltage stable? The screen image can appear to shake or vibrate at a particular time of day due to low supply voltage. The screen image can also appear to shake or vibrate if there is a problem with the video card or the computer's main board. The screen shows strange colors or just black and white. The screen suddenly has become unbalanced. Is the screen displaying only one color as if looking at the screen through a cellophane paper? Check the signal cable connection.
2. Check if the computer beeps more than 3 times when booting. (If it does, request an after-service for the main board of the computer.) 3. If you installed a new video card or if you assembled the PC, check if the installed adapter (video) driver and the monitor driver. 4. Check if the scanning ratio of the video screen is set at 50Hz or 160 Hz . (Do not exceed 60Hz when using the maximum resolution.) 5.
This box appears during normal operation if the video cable becomes disconnected or damaged. 4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor. If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly.
SyncMaster 795DF, 795MB Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom No images on the screen. I cannot turn on the monitor. Check List Solutions Is the power cord connected properly? Check the power cord connection and supply. Can you see " screen? Check the signal cable connection.
voltage wire near by? Is the voltage stable? The screen image can appear to shake or vibrate at a particular time of day due to low supply voltage. The screen image can also appear to shake or vibrate if there is a problem with the video card or the computer's main board. The screen shows strange colors or just black and white. The screen suddenly has become unbalanced. Is the screen displaying only one color as if looking at the screen through a cellophane paper? Check the signal cable connection.
2. Check if the computer beeps more than 3 times when booting. (If it does, request an after-service for the main board of the computer.) 3. If you installed a new video card or if you assembled the PC, check if the installed adapter (video) driver and the monitor driver. 4. Check if the scanning ratio of the video screen is set at 50Hz or 160 Hz . (Do not exceed 65 Hz when using the maximum resolution.) 5.
This box appears during normal operation if the video cable becomes disconnected or damaged. 4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor. If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly.
SyncMaster 997DF Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom No images on the screen. I cannot turn on the monitor. Check List Solutions Is the power cord connected properly? Check the power cord connection and supply. Can you see " screen? Check the signal cable connection.
voltage wire near by? Is the voltage stable? The screen image can appear to shake or vibrate at a particular time of day due to low supply voltage. The screen image can also appear to shake or vibrate if there is a problem with the video card or the computer's main board. The screen shows strange colors or just black and white. The screen suddenly has become unbalanced. Is the screen displaying only one color as if looking at the screen through a cellophane paper? Check the signal cable connection.
2. Check if the computer beeps more than 3 times when booting. (If it does, request an after-service for the main board of the computer.) 3. If you installed a new video card or if you assembled the PC, check if the installed adapter (video) driver and the monitor driver. 4. Check if the scanning ratio of the video screen is set at 50Hz or 160 Hz . (Do not exceed 60Hz when using the maximum resolution.) 5.
This box appears during normal operation if the video cable becomes disconnected or damaged. 4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor. If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly.
General General Model Name SyncMaster 591s / 591v Picture Tube Type 15" (38cm) Full square type (35cm viewable) Deflection angle 90 ° Dot Pitch 0.24mm (Horizontal) Screen type Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask. Multi-layer coated with anti-static/Glare.
90 ~ 264VAC rms, 60/50 Hz ± 3Hz Power Consumption Less than 55W (Maximum 65W) Dimensions (WxDxH) 361 x 379.2 x 347 mm / 14.2 x 14.9 x 13.7 inch (After installation of Stand) Weight 11.0 kg Environmental considerations Operating Temperature 32°F ~ 104°F(0°C ~ 40°C) Humidity 10% ~ 80%, non-condensing Storage Temperature -4°F ~113°F (-20°C ~ 45°C) Humidity 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system.
Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called Vertical Frequency or Refresh Rate.
General General Model Name SyncMaster 793s,793v Picture Tube Type 17"(43cm) Full square type (40.6cm viewable) Deflection angle 90 ° Dot Pitch 0.23mm (Horizontal) Screen type Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask. Multi-layer coated with anti-static.
100 ~ 240VAC rms ± 10%, 60/50 Hz ± 3Hz Power Consumption Less than 70W (Maximum 75W) Dimensions (WxDxH) 401 x 410 x 378 mm / 15.8 x 16.1 x 14.9 inch (After installation of Stand) Weight 14.3kg Environmental considerations Operating Temperature 32°F ~ 104°F(0°C ~ 40°C) Humidity 10% ~ 80%, non-condensing Storage Temperature -4°F ~113°F (-20°C ~ 45°C) Humidity 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system.
Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 800 x 600 53.700 85.100 56.250 +/+ VESA, 1024 x 768 68.700 85.000 94.500 +/+ Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency.
General General Model Name SyncMaster783DF,793DF,793MB Picture Tube Type 17"(43cm) DynaFlat (40.6cm viewable) Deflection angle 90 ° Dot Pitch 0.20mm (Horizontal) Screen type Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask. Multi-layer coated with anti-static.
100 ~ 240VAC rms ± 10%, 60/50 Hz ± 3Hz Power Consumption Less than 70W (Maximum 75W) Dimensions (WxDxH) 401 x 410 x 378 mm / 15.8 x 16.1 x 14.9 inch (After installation of Stand) Weight 14.3kg Environmental considerations Operating Temperature 32°F ~ 104°F(0°C ~ 40°C) Humidity 10% ~ 80%, non-condensing Storage Temperature -4°F ~113°F (-20°C ~ 45°C) Humidity 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system.
Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 800 x 600 53.700 85.100 56.250 +/+ VESA, 1024 x 768 68.700 85.000 94.500 +/+ Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency.
General General Model Name SyncMaster 795DF / 795MB Picture Tube Type 17"(43cm) DynaFlat (40.6cm viewable) Deflection angle 90 ° Dot Pitch 0.20mm (Horizontal) Screen type Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask. Multi-layer coated with anti-static.
90 ~ 264VAC rms, 60/50 Hz ± 3Hz Power Consumption Less than 75W Dimensions (WxDxH) 401 x 410 x 378 mm / 15.8 x 16.1 x 14.9 inch (After installation of Stand) Weight 14.3kg Environmental considerations Operating Temperature 32°F ~ 104°F(0°C ~ 40°C) Humidity 10% ~ 80%, non-condensing Storage Temperature -4°F ~113°F (-20°C ~ 45°C) Humidity 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system.
Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 1024 x 768 68.977 84.997 94.500 +/+ VESA, 1280 x 1024 79.976 75.025 135.00 +/+ Display Mode Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency.
General General Model Name SyncMaster 797DF Picture Tube Type 17"(43cm) DynaFlat (40.6cm viewable) Deflection angle 90 ° Dot Pitch 0.20mm (Horizontal) Screen type Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask. Multi-layer coated with anti-static.
90 ~ 264VAC rms, 60/50 Hz ± 3Hz Power Consumption Less than 90W Dimensions (WxDxH) 401 x 410 x 378 mm / 15.8 x 16.1 x 14.9 inch (After installation of Stand) Weight 14.3kg Environmental considerations Operating Temperature 32°F ~ 104°F(0°C ~ 40°C) Humidity 10% ~ 80%, non-condensing Storage Temperature -4°F ~113°F (-20°C ~ 45°C) Humidity 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system.
Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 1024 x 768 68.677 84.997 94.500 +/+ VESA, 1280 x 1024 91.146 85.024 157.50 +/+ Display Mode Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency.
General General Model Name SyncMaster 997DF Picture Tube Type 19"(48cm) DynaFlat (45.8cm viewable) Deflection angle 90 ° Dot Pitch 0.20mm (Horizontal) Screen type Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask. Multi-layer coated with anti-static.
Power Supply 90 ~ 264VAC rms, 60/50 Hz ± 3Hz Power Consumption Less than 110W Dimensions (WxDxH) 445 x 457.5 x 416 mm / 17.5 x 18.0 x 16.4 inch (After installation of Stand) Weight 18.2kg Environmental considerations Operating Temperature 32°F ~ 104°F(0°C ~ 40°C) Humidity 10% ~ 80%, non-condensing Storage Temperature -4°F ~113°F (-20°C ~ 45°C) Humidity 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system.
Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 1024 x 768 68.677 84.997 94.500 +/+ VESA, 1024 x 768 91.146 85.024 157.50 +/+ Display Mode Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency.
Contact SAMSUNG WORLD - WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America CANADA 1-800-SAMSUNG (7267864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG (7267864) http://www.samsung.com/mx U.S.A 1-800-SAMSUNG (7267864) http://www.samsung.com Latin America ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 0800-124-421 http://www.samsung.com/br CHILE 800-726-7864 (SAMSUNG) http://www.samsung.
CZECH REPUBLIC 844 000 844 http://www.samsung.com/cz DENMARK 38 322 887 http://www.samsung.com/dk FINLAND 09 693 79 554 http://www.samsung.com/fi FRANCE 08 25 08 65 65 (€ 0,15/min) http://www.samsung.com/fr GERMANY 01805 - 121213 (€ 0,12/Min) http://www.samsung.de HUNGARY 06 40 985 985 http://www.samsung.com/hu ITALIA 199 153 153 http://www.samsung.com/it LUXEMBURG 02 261 03 710 http://www.samsung.lu NETHERLANDS 0900 20 200 88 (€ 0.10/Min) http://www.samsung.
Terms Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called Vertical Frequency or Refresh Rate.
MÉXICO IMPORTADO POR: SAMSUNG ELECTRONICS MÉXICO. S.A. de C.V. Vía Lopez Portillo No. 6, Col. San Fco. Chilpan Tultitlán, Estado de México, C.P. 54940 Tel: 01-55-5747-5100 / 01-800-726-7864 EXPORTADO POR: Samsung Electronics CO.,LTD.
