User Manual

15
English
03 Basic Features
When Antenna Source is set to Satellite:
Channel Type (All / TV / Radio): Select the Channel
type to memorise.
Satellite: Selects the satellite to scan.
Scan Mode (All Channels / Free Channels Only):
Selects the scanning mode of the selected satellite.
Manual Store
Scans for a channel manually and stores in the TV.
If a channel is locked using the Child Lock function,
the PIN input window appears.
When Antenna Source is set to Air or Cable:
Digital Channel: When scanning has finished, channels
are updated in the channel list.
When selecting Antenna Air: Channel,
Frequency, Bandwidth
When selecting Antenna Cable: Frequency,
Modulation, Symbol Rate
Analogue Channel (Programme, Colour System,
Sound System, Channel, Search): If there is abnormal
sound or no sound, reselect the sound standard
required.
Channel mode
x
P (programme mode): When tuning is complete,
the broadcasting stations in your area have been
assigned to position numbers from P0 to P99. You
can select a channel by entering the position number
in this mode.
x
C (aerial channel mode) / S (cable channel mode):
These two modes allow you to select a channel
by entering the assigned number for each aerial
broadcasting station or cable channel.
When Antenna Source is set to Satellite:
Satellite: Selects the satellite using the up/down
buttons.
Transponder: Selects the transponder using the up/
down buttons.
Scan Mode (All Channels / Free Channels Only):
Selects either free or all channels to store.
Network Search (Disable / Enable): Enable / Disable
network search using the up/down buttons.
Signal Quality: Display the current status of
broadcasting signal.
Information on a satellite and its transponder is subject
to change depending on the broadcasting conditions.
When setting is completed, move to Search and press
the ENTER
button. Channel scan is started.
Satellite System Setup
The PIN input screen appears. Enter your 4 digit PIN number.
Satellite System Setup is available when Antenna is set to
Satellite. Before running Auto Store, set
Satellite System Setup. Then channel scan is run normally.
Satellite Selection: You can choose the satellites for
this TV.
LNB Power (Off / On): Enables or disables the power
supply for the LNB.
LNB Settings: Configures the outdoor equipment.
Satellite: Selects the satellite for receiving digital
broadcasts.
Transponder: Selects a transponder from the list or
adds a new transponder.
DiSEqC Mode: Selects DiSEqC mode for the selected
LNB.
Lower LNB Oscillators: Sets the LNB oscillators to a
lower frequency.
Upper LNB Oscillators: Sets the LNB oscillators to a
higher frequency.
Tone 22 kHz (Off / On / Auto): Selects the Tone 22
kHz depending on the LNB type. For a universal LNB it
should be Auto.
Signal Quality: Display the current status of
broadcasting signal.
Positioner Settings: Configures the antenna positioner.
Positioner (On / Off): Enables or disables the positioned
control.
Positioner Type (USALS / DiSEqC 1.2): Sets
the positioned type between DiSEqC 1.2 and
USALS(Universal Satellite Automatic Location System).
My Longitude: Sets the longitude for my location.
My Latitude: Sets the latitude for my location.
Satellite Longitude Settings: Sets the longitude of
user defined satellites.
User Mode: Sets the position of satellite antenna
according to each satellite. If you store the current
position of satellite antenna according to a certain
satellite, when the signal of that satellite is needed,
the satellite antenna can be moved to pre-populated
position.
Satellite: Selects the satellite to set the position for.
Transponder: Selects a transponder from the list for
signal reception.
Moving Mode: Selects the movement mode between
discrete and continuous movement.
Step Size: Adjusts the step size degrees for the
antenna rotation. Step Size is available when Moving
Mode is set to Step.
[UC6700]BN68-02841B-00L04.indb 15 2010-03-04 오전 11:29:55