EN FR Operating instructions Manuel d’instructions For household use only Pour utilisation domestique seulement VACUUM CLEANER ASPIRATEUR ❈ Before operating this unit, please read the instructions carefully. ❈ Avant d’utiliser l’appareil, lisez attentivement ce mode d’emploi. EN FR Register your product at www.samsung.com/global/register Enregistrez vos produits Samsung en vous connectant sur : www.samsung.
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following : READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING To reduce the risk of fire, electric shock, or injury. 1. Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing. 2. Do not use outdoors or on wet surfaces. 3. Do not allow to be used as a toy. Close attention is necessary when used by or near children. 4.
17. Do not use extension cords or an outlet with inadequate current carrying capacity. 18. Hold plug when rewinding onto cord reel. Do not allow plug to whip when rewinding. 19. Unplug electrical appliances before vacuuming them. 20. The hose contains electrical wires. Do not use if damaged, cut, or punctured. Avoid picking up sharp objects. 21. Always turn off this appliance before connecting or disconnecting either hose or motorized nozzle.
PARTS IDENTIFICATION HANDLE ON/OFF SWITCH SUCTION CONTROL HOSE DUST-FULL INDICATOR CORD REWIND BUTTON EXTENSION WANDS HEIGHT ADJUSTMENT KNOB POWER CONTROL BUTTON ON/OFF SWITCH HEAD LIGHT TOOL STORAGE COVER POWER BRUSH EN-3 BUTTON FOR SUCTION HOSE REMOVAL
ASSEMBLING THE VACUUM CLEANER FOR USE Attaching the Hose to the Canister Slide the Hose Clamper into the canister Inlet until it “Clicks” into place.(Fig. A-A) Attaching the Extension Wand to the Hose Slide the handle end of hose over the end of the wand until it “Clicks” into place. (Fig. A-B) They can be removed by pressing the button on the Hose. Attaching the Power Brush Slide the end of the Extension Wand onto the Power Brush Wand unitl it “Clicks” into place. (Fig.
POWER CORD 1) PULLING OUT The power cord is long enough to drawn out for convenience. 2) REWINDING When you have finished cleaning,disconnect the plug from the electrical outlet and simply press the cord rewind button lightly with your toe. NOTE : When removing the power cord from the electrical outlet, grasp the plug, not the cord. ON/OFF SWITCH You can start or stop your vacuum cleaner by pressing the on/off switch lightly with your toe.
AUTO MODE If you press AUTO MODE, the power is automatically set at 800watt. For example, when dust bag is full, the quantity of air to the motor will be decreased and power will be down followingly. AUTO MODE, in this case, increases the power automatically for sufficient suction. eh If you want to go back to the normal control type, just press "+" or "-" buttons. OPERATING THE BRUSH HEAD Push the ON/OFF switch(A) down.
PARK POSITION Located in the top rear side of the vacuum cleaner, there is a support for a convenient park position during pauses when using the nozzle. TRANSPORTING AND STORING THE VACUUM CLEANER For easy storage and transportation, this vacuum cleaner has a clip system built onto the body, which will keep the tube, hose and nozzle in a vertical position.
3) After removing the used dust bag, insert the cardboard bag collar of the new dust bag into its original position. 4) Press the dust cover down gently until the clamper relocks. DUST-FULL INDICATOR If the “Dust-Full” indicator switches to “RED” while you are cleaning, the dust bag is full and must be replaced. NOTE : If the “Dust-Full” indicator continues to display “RED” even after changing the dust bag, turn the cleaner off and check whether the hose, tube or nozzle is clogged.
MAINTENANCE OR REPLACEMENT OF THE FILTERS 1) INLET-FILTER. • Open the dust cover. • After detaching the filter, wash it lightly with water, dry it in the shade, and then insert it in its original position. • Close the dust cover. 2) OUTLET-FILTER. • The outlet-filter which the air comes out from the vacuum-cleaner. • Open the dust cover, and then pull the hook upward located at the front of the hepa filter. • Remove and replace the exhausted outlet-filter.
CAUTION: Do not invert the power brush while it is running 3. Checking the Performance of the Power Brush You may check whether the power brush is operating correctly by lifting up the extension tube slightly to view the back of the brush. The Power Brush will not operate when it is jammed or the unit is turned off. If the Power Brush is jammed, Unplug the power cord from the electrical outlet. Turn power brush over and remove the jammed object.
1) Remove the brush cover, Grasp the brushroller firmly, and pull it out. BELT 2) Remove the flat belt from the motor shaft and the brushroller, Loop the new belt around the motor shaft and then loop it around the brushroller. BRUSHROLLER MOTOR SHAFT 3) Reinsert the brushroller, making sure that both ends of the brushroller are fitted into the grooves of the nozzle head. 4) Be sure that the is not twisted.
TROUBLESHOOTING PROBLEM CAUSE REMEDY Motor does not start No voltage Check cable, plug and socket. Suction force is gradually reduced Filter,nozzle,suction hose tube blocked, or bag full. Remove the obstruction or replace bag.
DIRECTIVES DE SURETÉ IMPORTANTES Lorsque vous utilisez un appareil électrique, certaines précautions doivent être exercées, incluant les suivantes : LIRE TOUTES LES INSTRUCTIONS AVANT D’UTILISER L’APPAREIL.CONSERVER CES DIRECTIVES. ATTENTION Pour réduire le risque d’un feu, décharge électrique ou blessure: 1. Utiliser cet appareil tel que décrit dans le manuel. 2. Ne pas laisser votre aspirateur sans supervision lorsqu’il est branché ou en fonction.
16. Ne pas utiliser l’appareil sans sac et filtres. 17. Soyez prudent lors du nettoyage des escaliers. Pour éviter des blessures ou dommages, l’appareil doit demeurer au pied des escaliers. 18. Utiliser seulement que les accessoires recommandés par le manufacturier. 19. Assurez-vous que l’aspirateur n’est pas en fonction avant de débrancher. 20. Le flexible contient des fils électriques. Ne pas utiliser s’il est endommagé, coupé ou perforé. Éviter d’aspirer des objets pointus. 21.
IDENTIFICATION DES PIÈCES POIGNÉE INTERRUPTEUR ARRÊT/ DÉPART RÉGULATEUR D’AIR BOYAU INDICATEUR DE SAC PLEIN TUBE TÉLESCOPIQUE BOUTON D’ENROULEUR AUTOMATIQUE BOUTON DE VARIABILITÉ DE SUCCION BOUTON D’ÉLÉVATION DU ROULEAU INTERRUPTEUR ARRÊT/DÉPART LUMIÈRE COUVERCLE DE BOITE A OUTILS BALAI ÉLECTRIQUE BOUTON POUR DETACHEMENT DU TUYAU DE SUCCION FR-3
ASSEMBLEMENT DE L’ASPIRATEUR L’embout de machine du boyau Insérer l’embout de machine du boyau dans l’entrée de l’aspirateur jusqu’à ce que vous entendiez un ‘click’. (Fig. A-A) La poignée du boyau et le tube télescopique Insérer la poignée du boyau dans le tube télescopique jusqu’à ce que vous entendiez un ‘click’. (Fig A-B) Ce tube peut-être retirer en appuyant sur le bouton barrure situé à la poignée.
CORDE D’ALIMENTATION 1) DÉROULER La corde d’alimentation est d’une bonne longueur pour que vous puissiez la dérouler à une longueur confortable. 2) ENROULER Après le nettoyage, déconnectez la fiche de la prise de courant puis appuyez légèrement avec votre doigt sur le bouton de rembobinage du câble. NOTE : Pour débrancher la corde d’alimentation, assurez-vous de tenir la fiche et non pas la corde seule..
MODE AUTO Lorsque vous appuyez sur MODE AUTO, la puissance est réglée sur 800watts. Par exemple, lorsque le sac à poussière est plein, la quantité d’air dirigé vers le moteur diminue en provoquant la diminution de puissance. Dans ce cas, la fonction MODE AUTO augmente la puissance automatiquement en vue d’aspiration suffisante. eh Pour revenir au contrôle normal, appuyez simplement sur le bouton "+" ou "-". FONCTIONNEMENT DU BALAI ÉLECTRIQUE Appuyez sur l’interrupteur Arrêt/Départ vers l’avant.
STATIONNEMENT DU BALAI ÉLECTRIQUE Grâce au support situé à l’arrière de l’aspirateur, vous pouvez insérer l’attache au coude du balai électrique pour stationner celui-ci. TRANSPORT ET RANGEMENT DE VOTRE ASPIRATEUR Pour un rangement et transport facile, l’aspirateur est muni d’une attache au tube qui peut être inséré dans le support trouvé sous l’aspirateur. De cette façon, votre aspirateur, boyau, tube et balai électrique demeureront en position verticale.
3)Après avoir enlevé le sac à poussière plein, insérez le col de la boîte en carton du nouveau sac à poussière dans sa position originale. 4) Fermer la porte du compartiment INDICATEUR DE SAC PLEIN Si l’indicateur "Sac plein" bascule sur "ROUGE" pendant le nettoyage, vous devez remplacer le sac à poussière par un nouveau car il est plein.
ENTRETIEN OU REMPLACEMENT DES FILTRES 1) FILTRE D’ENTREE. • Ouvrez le couvercle du compartiment à poussière. • Après avoir retiré le filtre, lavez-le légèrement, séchez-le dans l’ombre puis insérez-le dans sa position originale. • Fermez le couvercle du compartiment à poussière. 2) FILTRE DE SORTIE. • Le filtre de sortie par lequel l’air sort de l’aspirateur. • Ouvrez le couvercle du compartiment à poussière et poussez vers le haut l’agrafe située sur le filtre HEPA.
AVERTISSEMENT:Ne pas renverser le balai électrique lorsqu’il est en fonction. 3. Vérification de la performance du balai électrique. Vous pouvez lever le balai électrique du plancher légèrement pour vérifier la performance du rouleau. Le balai électrique ne fonctionnera pas si il y a une obstruction. Si le balai électrique est obstrué, débrancher la corde d’alimentation de la prise. Renverser le balai et retirer l’objet obstruant l’entrée du balai. L’ENTRETIEN DU BALAI ÉLECTRIQUE 1.
1) Enlever le dessus en plastique du balai. Tenir le rouleau fermement et le retirer de son compartiment. BELT 2) Enlever la courroie usée du rouleau et de la tige du moteur. Réinsérer une courroie neuve autour de la tige du moteur et du rouleau. BRUSHROLLER MOTOR SHAFT 3) Replacer le rouleau dans son com partiment. Assurez-vous que chaque bout du rouleau soit bien ancré dans le compartiment. 4) Assurez-vous que la courroie ne soit pas tordue.
DÉPANNAGE Problème Cause Solution Moteur ne démarre pas No voltage Vérifier la corde d’alimentation, prise, fiche Le niveau de succion est Réduit Filtre, balai électrique, boyau, Sac plein Enlever l’obstruction Le niveau de succion est Réduit Vérifier que la corde d’alimentation ne soit pas tordue Tirer la longueur de 6-10’ et appuyer sur le bouton d’enrouleur FR-12
DJ68-00093V REV(0.