DJ68-00093J 6/17/02 12:59 PM Page 1 Operating Instructions VACUUM CLEANER ❈ Before operating this unit, please read the instructions carefully.
DJ68-00093J 6/17/02 12:59 PM Page 2 FEATURES Features include indicator and automatic cord rewind. NOTE : Not all models have the same features. IMPORTANT SAFEGUARDS 1. Read all instructions carefully. Before switching on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate on the bottom of the cleaner. 2. WARNING: Do not use the vacuum cleaner when rug or floor is wet. 3. Close supervision is necessary when any appliance is used by or near children.
DJ68-00093J 6/17/02 12:59 PM Page 3 IDENTIFICATIONS OF PARTS HOSE * REMOTE POWER CONTROL * (REMOTE CONTROL TYPE ONLY) HANDLE * SUCTION REGULATOR * TUBE * CYCLONIC FILTER * CORD REWIND BUTTON TRANSPARENT TUBE * ▼ FLOOR NOZZLE * Features marked with AUTO BUTTON POWER CONTROL SWITCH * ON/OFF BUTTON TOOL STORAGE COVER BUTTON FOR SUCTION HOSE REMOVAL DUST COVER CLAMPER FOR DUST BAG COMPARTMENT CARRYING HANDLE * may vary according to model.
DJ68-00093J 6/17/02 12:59 PM Page 4 ASSEMBLING THE VACUUM-CLEANER READY FOR USE 1) Connect the suction hose to the suction tube. 2) Adjust the suction tube(depending on model). ① EXTENDING : Holding the narrow part of the telescopic tube with one hand, push the handle in the opposite direction with your other hand. ➁ SHORTENING : Holding the narrow part of the telescopic tube with one hand, pull the handle towards it using the other hand.
DJ68-00093J 6/17/02 12:59 PM Page 5 POWER CORD 1) PULLING OUT : The power cord is long enough to drawn out for convenience. 2) REWINDING : When you have finished cleaning,disconnect the plug from the electrical outlet and simply press the cord rewind button lightly with your toe. NOTE : When removing the power cord from the electrical outlet,grasp the plug,not the cord. ON/OFF SWITCH You can start or stop your vacuum cleaner by pressing the on/off switch lightly with your toe.
DJ68-00093J 6/17/02 12:59 PM Page 6 AUTO MODE (BUTTON CONTROL TYPE ONLY) If you press AUTO MODE, the power is automatically set at 1200~1300 watt. This mode reduces the suction power fluctuation which is caused by the fluctuation of airflow quantity to the motor. For example, when dust bag is full, the quantity of air to the motor will be decreased and power will be down followingly. AUTO MODE, in this case, increases the power automatically for sufficient suction.
DJ68-00093J 6/17/02 12:59 PM Page 7 USING THE ACCESSORIES Open the tool storage cover upwards. CREVICE Crevice tool for radiators, crevices, corners, between cushions. DUSTING Dusting brush for furniture, shelves, books, etc. UPHOLSTERY Upholstery brush for cushions and drapery.
DJ68-00093J 6/17/02 12:59 PM Page 8 REPLACING THE DUST BAG 1) To open the dust cover of the dust bag compartment, press the clamper upwards(the clamper is located at the front of the dust cover). 2) Remove the dust bag from the cleaner 3) After removing the used dust bag, insert the cardboard bag collar of the new dust bag into its original position. 4) Press the dust cover down gently until the clamper relocks.
DJ68-00093J 6/17/02 12:59 PM Page 9 CYCLONIC FILTER (ONLY CYCLONIC FILTER TYPES) You can use a dust bag in your cleaner for a long time thanks to the Cyclonic Filter system and it maintain the maximum cleaning efficiency. The larger particle of dust filtered from Cyclonic Filter remain in Dust Barrel when suctioned air and dust revolves in the Cyclonic Filter. So the dust bag contains only smaller ones. When the Dust Barrel is filled with dust up to the indicating line, it needs disposing and cleaning.
DJ68-00093J 6/17/02 12:59 PM Page 10 MAINTENANCE OR REPLACEMENT OF THE FILTERS ▲ INLET FILTER The secondary filter, located behind the grille in the back of dust bag compartment, protects the motor from dirt particles. Do not allow the filter to become clogged. Suction power reduction or motor damage may result. If filter becomes dirty, pull off the grille and lift out filter. After cleaning the secondary filter attach it in place.
DJ68-00093J 6/17/02 12:59 PM Page 11 USAGE OF FLOOR NOZZLE FOR RUG / FLOOR SELECTOR Before use make sure that the position of the selector is in the right position for the type of surface to be cleaned. Select the carpet indicator ➀ when cleaning carpets. Select flat surface indicator ➁ when cleaning the floors, tiles, etc. NOTE: For optimum efficiency, clean floor brush with crevice tool.
DJ68-00093J 6/17/02 12:59 PM Page 12 TROUBLE SHOOTING PROBLEM CAUSE REMEDY Motor does not start. No power supply. Check cable, plug and socket. Suction force is gradually decreasing. Filter, nozzle, suction hose or tube is blocked. Remove the object. Cord does not rewind fully. Check that the cord is not twisted or wound unevenly. Pull the cord out 2~3m & push down the cord rewind button. DJ68-00093J REV(0.
