POWERbot User manual SR1AM70****, SR2AM70**** Series • Before operating this unit, please read the instructions carefully. • For indoor use only.
Contents 03 Safety information 10 Installation Accessories / Installation note 12 Charging Automatic charging / Recharging / Low battery (Lo) POWERbot 14 Using Turning the power on/off / Selecting cleaning modes / Using special cleaning functions / About the boundary markers / Using Energy-saving mode 18 Using the remote controller 21 Name of each part Top / Bottom / Display panel 23 Setting time/schedule Setting the time / Setting the schedule 26 Cleaning and maintaining Cleaning the dustbin / Cleanin
Safety information SAFETY INFORMATION • Before operating the appliance, please read this manual thoroughly and retain it for your reference. • Because the following operating instructions cover various models, the characteristics of your vacuum cleaner may differ slightly from those described in this manual. WARNING WARNING CAUTION/WARNING SYMBOLS USED WARNING CAUTION Indicates that a danger of death or serious injury exists. Indicates that a risk of personal injury or material damage exists.
Safety information IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should be observed, including the following: READ ALL INSTRUCTIONS BEFORE USING YOUR POWERbot. Unplug from outlet when not in use and before conducting maintenance. WARNING: To reduce the risk of fire, electric shock, or injury: GENERAL • Use only as described in this manual. • Do not operate POWERbot or the battery charger / docking station if it has been damaged in any way.
• • • • Do not use extension cords or outlets with inadequate current carrying capacity. Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord. Do not mutilate or incinerate batteries as they will explode at high temperatures. Do not attempt to open the battery charger / docking station. Repairs should only be carried out by a qualified Samsung service center.
Safety information REGULATORY NOTICE 1. FCC Notice CAUTION FCC CAUTION: • Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device complies with Part 15 of FCC Rules. Operation is Subject to following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received including interference that cause undesired operation.
2. IC Notice • The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. • This Class B digital apparatus complies with Canadian ICES-003. • Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.
Safety information WARNING Power related f To prevent the risk of electric shock or fire: – Do not damage the power cord. – Do not pull the power cord too hard or touch the power plug with wet hands. – Use only power sources that provide between 100 and 240 volts. Do not plug the POWERbot into a multi-outlet power strip. Do not place the power cord where it can be stepped on, tripped over, or where the POWERbot can run over it. – Do not use a damaged power plug, power cord, or loose power outlet.
f Insert the dustbin before using the POWERbot. f For proper automatic recharging, do the following: – Always turn on the power of the docking station. – Install the docking station where the POWERbot can find it easily. – Do not leave any object in front of the docking station. f When installing the docking station, do not leave the cord on the floor where the POWERbot can run over it. f Do not use POWERbot on black colored floors. – The POWERbot may not be able to operate normally.
Installation The docking station must be plugged in and turned on at all times. Install the docking station in a place without obstacles and where there is no danger of falling. f .3 t3 u o Ab (1 m) t Abo 1.6 ut (0.5 ft m) Abo u 1.6 t ft (0.5 m) DC-I N 1 Connect the battery charger jack to the docking station 2 Connect the power cord to the battery charger The side with the sticker attached must face down.
Accessories or Remote controller (Optional) Batteries (AAA type) (Optional) User manual Spare filter (Optional) Docking station Power cord Battery charger Boundary markers (Optional) ✻ Accessories may differ depending on the models. ✻ Refer to page 17 for the installation of boundary markers. Installation note Note f Install the docking station in a place where the floor is level and the wall is straight. f It is best to install the docking station along the grain of wooden floors.
Charging After completely charging the POWERbot for the first time (after purchase), it can be used for 60 min. in Nomal ( ) mode. (Refer to the page 41 for the charging time.) Smart Charging If the POWERbot's charge runs low while it is in Auto clean mode, it will automatically return to the docking station to recharge, and then will return to the cleaning area after its battery is 2/3rds charged. (Maximum: 2 times.) WARNING • Rated input voltage of this product is 100240 V~.
Automatic charging 1. SR1AM7010U* Series If the battery indicator blinks at 0.4 sec. intervals, the POWERbot will automatically return to the docking station to recharge. 2. SR1AM7040W* / SR2AM70**** Series When the battery indicator blinks during cleaning, the POWERbot will return to the docking station to charge itself automatically. Recharging You can command the POWERbot to recharge at the docking station while it is cleaning.
Using POWERbot You must turn on the emergency switch on the bottom of the unit before using POWERbot. Turning the power on/off Press the WARNING button for more than 3 seconds • When POWERbot is not used for 30 min.; SR1AM70**U* / SR2AM70**U* series: Enters energy-saving mode. SR1AM70**W* / SR2AM70**W* series: Automatically returns to the docking station to be charged. Starting Auto clean mode Press and release this button. The POWERbot moves and automatically cleans the set areas only once.
Selecting cleaning modes Displayed icons Cleaning mode How to select SR1AM7040W* SR2AM70**** SR1AM7010U* Auto clean Spot clean Repeat clean ], ✻ Press the [A,B type [C type ] on the remote controller first, and then press the [Start/Stop ]. - Manual clean ✻ Manual clean mode can be selected by the direction control buttons of the remote controller. - ✻ If POWERbot fails to return to the docking station, it will enter energy-saving mode and the display panel will be turned off.
Using POWERbot Cleaning method for each mode About 4.9 ft (1.5 m) About 4.9 ft (1.5 m) Auto clean Spot clean Manual clean Repeat clean Automatically cleans the set areas only once. ✻ SR1AM7010U* series : Cleans repeatedly until the battery is depleted. Cleans a localized area intensely. It can be used to clean bread or cookie crumbs. You can move POWERbot with the remote controller to clean the desired spot. ✻ This function is not available on the SR1AM7010U* series.
About the boundary markers To prevent the POWERbot from entering the following areas, place the boundary markers on the floor in an shape at intervals of about 5.9 in (15 cm). About 5.9 in (15 cm) Boundary markers About 5.9 in (15 cm) About 1.9 in (5 cm) Boundary markers Where a raised spot exceeds 1.9 in (5 cm) Where there is a slide, swing, fireplace, or any flammable substance or moisture. Boundary markers Above 0.6 in (1.5 cm) boundary markers Where a threshold is higher than 0.6 in (1.
Using the remote controller [A Type] [B Type] 1 1 3 3 1, 2 5 1, 2 5 4 2 4 4 2 4 Refer to page 23 Refer to page 23 [C Type] 1 3 1, 2 5 6 2 4 4 Refer to page 24 ENGLISH-18
[A Type] / [B Type]/ [C Type] 1 Power / Recharging / Start/Stop Power Recharging Start/Stop Turn POWERbot's power on/off Select to recharge POWERbot at the docking station automatically Select to start or stop the cleaning process 2 Cleaning modes Auto clean Select to clean all set areas only once and then have the POWERbot automatically return to the docking station.
Using the remote controller 5 Manual clean mode & Direction control Move forward Select to move forward Turn left Select to turn left Turn right Select to turn right ✻ Moving backward is not available. 6 Point cleaning Available only with C type remote controllers. You can use the remote controller to point and clean the desired spot while the POWERbot is in cleaning process. Point the red light on the floor within 1.6 ft (0.5 m) of the POWERbot's location.
Name of each part ENGLISH-21 Top 1. 2. 3. 4. 5. 6. 7. 8. Display panel Remote control signal receiver Obstacle sensor Dustbin Camera Dustbin button Bumper sensor Auto shutter tool Bottom 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
Name of each part Display panel 1. 2. 3. 4. Daily schedule Normal/Turbo mode Battery indicator Spot cleaning button, daily schedule (3sec) 5. Start/Stop button, Turbo mode (3sec) 6. Recharging button ✻ SR1AM70**W* / SR2AM70**W* : Wi-Fi supported model ENGLISH-22 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16.
Setting time/schedule [A Type, B Type] Only Auto clean mode can be scheduled. Setting the time You must set the current time before using the One-time/daily schedule function. Start setting Select "Hour" Select "Minute" Setting complete Select "AM/PM" Skip to previous, next setting Setting the schedule You can set/cancel the schedule only when the POWERbot is docked in the docking station.
Setting time/schedule [C Type] Only Auto clean mode can be scheduled. Setting the time You must set the current time before using the One-time/daily schedule function. Start setting Select "Hour" Select "Minute" Setting complete Select "AM/PM" Skip to previous, next setting Setting the schedule You can set/cancel the schedule only when the POWERbot is docked in the docking station.
[SR1AM7010U* series] For the models which do not include a remote controller, you can set a daily schedule as described below. Setting the schedule You can set/cancel the schedule only when the POWERbot is docked in the docking station. Press for 3 seconds. When the schedule LED is turned on, the daily schedule is set. ✻ The time you pressed the button will be set as the time that the POWERbot is scheduled to begin cleaning.
Cleaning and maintaining You must turn off the emergency switch before cleaning the POWERbot. Cleaning the dustbin the button to 1 Press remove the dustbin the dustbin 2 Remove cover Remove dust in the 3 dustbin and cyclone unit 'Click' the cyclone Reassemble the 4 Detach 5 unit from the dustbin dustbin Reinsert the dustbin 6 into the main body cover, and then wash the dustbin and the filter until it clicks Cleaning the sensors and the camera Lightly wipe with a soft cloth.
Cleaning the brush and Auto shutter tool Brush design may differ depending on the model. Do not clean the brush with water. the 1 Remove brush cover 2 Remove the brush 5 Reassemble the brush the 3 Clean brush 6 4 Clean the auto shutter tool Reassemble the brush cover Cleaning the Driving wheel a soft cloth on the floor and place 1 Put POWERbot upside-down on the cloth. a blunt rod or tweezers to remove 2 Use foreign matter.
SmartThings App The SmartThings App is only compatible with models that have a Wi-Fi function. Setting up the wireless router f Please refer to the user manual of your wireless router if you have access problems. f Samsung POWERbot supports only Wi-Fi 2.4 Ghz. f Samsung POWERbot supports IEEE 802.11b/g/n and Soft-AP. – IEEE 802.11n is recommened. f Samsung POWERbot supports only DHCP (Dynamic Host Configuration Protocol). Please make sure that the DHCP server option is activated on your wireless router.
Downloading the SmartThings App f Download and install the SmartThings app from the markets (Google Play Store, Apple App Store, or Samsung Galaxy Apps). To find the app, use the keyword “SmartThings”. Note f SmartThings is incompatible with tablets and some mobile devices. – Android 6.0 or later (at least 2GB of RAM) is recommended. f iPad and some mobile devices may not be supported. – iOS 10.0 or later / iPhone 6 or later is supported.
SmartThings App Adding a device to the SmartThings APP 1. Connect your smartphone to your wireless router. – If the smartphone is not connected, turn on the Wi-Fi in the Settings App and select a wireless router you want to connect to. – Disable the "Mobile data" use option of a smartphone to use Wi-Fi only and connect a device. 2. Launch the SmartThings app on your smartphone. 3. If a pop-up saying that a new device has been found appears, tap ADD NOW.
Software Update f When the POWERbot is charging on the docking station, the POWERbot connects to the server and then checks if a software is available. If a new software is found, POWERbot will automatically download and update it. f If “UP” is displayed on the display panel while the POWERbot is charging, it means that an update is in progress. Please wait for completing the update before using the POWERbot.
Notes and cautions f The POWERbot cannot vacuum clumps of dirt, so some may remain on the floor after cleaning. Charging Notes f If the battery overheats during charging, it may take longer to charge. f If automatic charging is not working, do the following: – Turn the emergency switch (on the bottom of POWERbot) off and on again. – Unplug the docking station's power plug and then plug it back on. – Unplug the docking station, and then check whether there is any foreign matter on the charging pins.
f Since the brush removes dirt from the floor during cleaning, foreign matter such as thread, long hair, etc. may get caught in it. For the best cleaning results, check and clean it regularly. f If a brush or brush cover is not assembled correctly after the maintenance work, scratches may occur on the floor, or product malfunction may occur. Therefore, assemble them correctly by checking the maintenance method.
Information codes three 1 The indicators below 2 blink and an information codes alarm sounds. Turn off the emergency switch, check the instructions below, and then take appropriate action. information 3 The code will disappear when you turn on the emergency switch Information codes animation Information codes Information codes Checklist The POWERbot is caught, stuck or trapped while moving. fTurn off the emergency switch, and then move the POWERbot to another area.
information 1 The code below appears and an information codes alarm sounds. 2 Turn off the emergency switch, check the instructions below, and then take appropriate action. Information codes information 3 The code will disappear when you turn on the emergency switch Checklist The POWERbot is caught, stuck or trapped while moving. fTurn off the emergency switch, and then move the POWERbot to another area. Foreign matter is caught in the brush.
Troubleshooting Symptom Checklist The POWERbot is not working at all. fCheck if the emergency switch is on. fCheck if all the icons are displayed on the display panel. fCheck if the POWERbot's battery is depleted. – If "Lo" is displayed, place the POWERbot in the docking station to charge it. – If the battery indicator is blinking, manually place the POWERbot in the docking station to charge. (SR1AM7010U* series only) fReplace the batteries (AAA type) if the remote controller is not working.
Symptom Checklist I have installed the SmartThings app, but the POWERbot fails to connect. fYou can use the SmartThings app with the POWERbot only after connecting the wireless router and the POWERbot through the EasySetup procedure. See pages 28 through 31. I cannot log into my Samsung account. fCheck your ID and password on the screen of the Samsung account. A message appears saying there is a failure during Easy-Setup.
Troubleshooting Symptom Checklist SmartThings App cannot be installed. fSmartThings App operates on Android OS 6.0 or later, iOS 10 or later. fThe supporting OS version for SmartThings App may change later. fFor rooted smart devices, standard installation and use will not be guaranteed. fTry the product registration procedure again by referring to the popup messages. fPlease refer to the “Setting up the wireless router” in the user manual.
Symptom Checklist A connection cut between the SmartThings App and the POWERbot suddenly occurs during normal operation of the app. fIf the POWERbot is distant from a wireless router, connection cut may occur. fReset the POWERbot and the smartphone, and check the connection again. fIf the connection cut occurs repeatedly, try the product registration again. fWhen the SSID/password of a wireless router is changed, try the product registration again.
Open Source Announcement The software included in this product contains open source software. You may obtain the complete corresponding source code for a period of three years after the last shipment of this product by sending an email to mailto:oss.request@samsung.com. It is also possible to obtain the complete corresponding source code in a physical medium such as a CDROM; a minimal charge will be required. The following URL http://opensource.samsung.
Specifications Classification Item Size (D x H x L) Mechanical specifications (POWERbot) Power specifications Weight Sensor Button type of POWERbot Power voltage Power consumption Battery specifications Charging type Cleaning mode Cleaning Charging time Cleaning time Turbo mode (On the basis Normal mode of hard floor) Detail information SR1AM7010U* SR1AM7040W* 13.4 in x 3.8 in x 13.7 in (340 mm x 97 mm x 348 mm) 8.
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. Country Customer Care Center Web Site CANADA 1-800-SAMSUNG (726-7864) 1-844-SAM-PAYS (726-7297) www.samsung.com/ca/support (English) www.samsung.com/ca_fr/support (French) U.S.A 1-800-SAMSUNG (726-7864) 1-844-SAM-PAYS (726-7297) www.samsung.
POWERbot Manual del usuario Serie SR1AM70****, SR2AM70**** • Antes de poner en funcionamiento esta unidad, lea atentamente las instrucciones. • Para uso en interiores solamente.
Contenido 03 Información sobre seguridad 10 Instalación Accesorios / Nota sobre la instalación 12 Carga Carga automática / Recarga / Batería baja (Lo) del POWERbot 14 Uso Encendido y apagado / Selección de los modos de limpieza / Uso de las funciones de limpieza especiales / Acerca de los marcadores de límite / Uso del modo de ahorro de energía 18 Uso del control remoto 21 Nombre de cada pieza Parte superior / Parte inferior / Visor 23 Ajuste de la hora/programación Ajuste de la hora / Ajuste de la p
Información sobre seguridad INFORMACIÓN SOBRE SEGURIDAD • Antes de poner en funcionamiento la unidad, lea detenidamente este manual y consérvelo para su referencia. • Debido a que las siguientes instrucciones de funcionamiento corresponden a diversos modelos, es posible que las características de su aspiradora difieran ligeramente de las que se describen en este manual.
Información sobre seguridad INSTRUCCIONES IMPORTANTES DE SEGURIDAD Al utilizar un electrodoméstico deben seguirse unas precauciones básicas, incluidas las siguientes: LEA TODAS LAS INSTRUCCIONES ANTES DE USAR SU POWERbot Desenchúfelo del tomacorriente cuando no lo utilice y antes de realizar el mantenimiento. ADVERTENCIA: para reducir el riesgo de incendio, descargas eléctricas o lesiones: GENERAL • Utilícelo solo como se describe en el manual.
• No trate de abrir el cargador de la batería/estación de carga. Las reparaciones deben efectuarse únicamente en un centro de servicio calificado de Samsung. • No exponga el cargador de la batería/estación de carga a temperaturas altas ni permita que entren en contacto con ningún tipo de humedad. POWERbot • No aspire objetos duros o cortantes, tales como vidrio, clavos, tornillos, monedas, etc. • No lo utilice sin el filtro en su lugar.
Información sobre seguridad AVISO REGULATORIO 1. Aviso de la FCC (Federal Communications Commission) PRECAUCIÓN PRECAUCIÓN de la FCC: • Todos los cambios y modificaciones que no cuenten con la aprobación expresa de la parte responsable del cumplimiento pueden invalidar la autoridad del usuario para operar el equipo. • Este aparato cumple con la sección 15 de las Normas de la FCC. El funcionamiento se encuentra sujeto a las siguientes dos condiciones: 1.
DECLARACIÓN DE LA FCC SOBRE LA EXPOSICIÓN A LA RADIACIÓN: • Este equipo cumple con los límites de exposición a la radiación establecidos por la FCC para un entorno no controlado. Este equipo debe instalarse y utilizarse con una distancia mínima de 20 cm entre el radiador y su cuerpo. Este aparato y su/s antena/s no deben ubicarse ni utilizarse junto con ninguna otra antena o transmisor. 2.
Información sobre seguridad ADVERTENCIA Acerca de la alimentación eléctrica f Evite el riesgo de que se produzca una descarga eléctrica o un incendio. – No dañe el cable de alimentación. – No jale el cable de alimentación con excesiva fuerza ni toque el enchufe con las manos mojadas. – Utilice únicamente fuentes de alimentación de 100-240 V~ y no utilice enchufes múltiples para alimentar varios aparatos al mismo tiempo. (No deje el cable suelto por el piso.
f Antes de operar el POWERbot, retire los objetos que puedan romperse, como marcos, espejos y objetos de porcelana, a fin de que el POWERbot pueda funcionar sin interrupciones. f Inserte el contenedor de polvo antes de usar el POWERbot. f Para una recarga automática correcta, preste atención a lo siguiente. – Encienda siempre la alimentación de la estación de carga. – Instale la estación de carga donde el POWERbot pueda encontrarla fácilmente. – No deje ningún objeto delante de la estación de carga.
Instalación La estación de carga debe estar enchufada y encendida siempre. Instale la estación de carga en un lugar sin obstáculos ni riesgo de caída. ft .4 x o r Ap m) (1 Apr ox 2 ft (0.5 m) Apr ox 2 ft . (0.5 m) DC-I N 1 Conecte el terminal del cargador de la batería a la estación de carga 2 Enchufe el cable de alimentación al cargador de la batería Cuando utilice el cargador de la batería, el lado del adhesivo debe estar hacia abajo.
Accesorios o Control remoto (opcional) Pilas (tipo AAA) (opcional) Manual del usuario Filtro de repuesto (opcional) Estación de carga Cable de alimentación Cargador de la batería Marcadores de límite (opcional) ✻ Los accesorios pueden variar según los modelos. ✻ Consulte la página 17 para obtener información acerca de los marcadores de límite. Nota sobre la instalación Nota f Instale la estación de carga en un lugar donde el piso y la pared sean regulares.
Carga Una vez que el POWERbot está completamente cargado por primera vez (después de la compra), puede utilizarse durante 60 minutos en modo Normal ( ). (Consulte la página 41 para ver el tiempo de carga.) Carga inteligente Si el POWERbot se queda sin carga en el modo de limpieza automática, regresa automáticamente a la estación para cargarse y reinicia la operación para completar la limpieza de la zona cuando se han cargado dos tercios de la batería. (Máximo 2 veces).
Carga automática 1. Serie SR1AM7010U* Si el indicador de la batería parpadea en intervalos de 0.4 segundos, el POWERbot regresa automáticamente a la estación de carga para cargarse. 2. Serie SR1AM7040W* / SR2AM70**** Cuando el indicador de la batería parpadea durante la limpieza, el POWERbot regresa a la estación de carga para cargarse automáticamente. Recarga Puede ordenar al POWERbot que se recargue automáticamente en la estación de carga mientras está limpiando.
Uso del POWERbot Debe encender el interruptor de emergencia en la parte inferior de la unidad antes de usar el POWERbot. Encendido y apagado Presione el botón ADVERTENCIA durante más de 3 segundos • Cuando no se usa el POWERbot durante 30 minutos Serie SR1AM70**U* / SR2AM70**U*: Se pone en modo de ahorro de energía. Serie SR1AM70**W* / SR2AM70**W*: Regresa automáticamente a la estación de carga para cargarse. Inicio del modo de limpieza automática Presione y libere este botón.
Selección de los modos de limpieza Modo de limpieza Ícono mostrado Cómo seleccionarlo SR1AM7040W* SR2AM70**** SR1AM7010U* Limpieza automática Limpieza localizada Limpieza repetida ], ✻ Presione el [tipo A,B [tipo C ] del control remoto primero y luego presione el [Inicio/ Detención ]. - Limpieza manual ✻ El modo de limpieza manual puede seleccionarse con los botones del control de dirección del control remoto.
Uso del POWERbot Método de limpieza para cada modo Aprox. 6 ft (1.5 m) Aprox. 6 ft (1.5 m) Limpieza automática Limpieza localizada Limpieza manual Limpieza repetida Limpia automáticamente las zonas establecidas una única vez. ✻ Serie SR1AM7010U* : Limpia repetidamente hasta que se agota la batería. Puede desplazar el POWERbot con el control remotopara limpiar el punto deseado. ✻ Esta función no se aplica a la serie SR1AM7010U*. Limpia repetidamente hasta que se agota la batería.
Acerca de los marcadores de límite Para evitar que el POWERbot entre en las siguientes zonas, fije los marcadores de límite en forma de sobre el piso en intervalos de unos 5.9 in (15 cm). Aprox. 5.9 in (15 cm) Marcadores de límite Aprox. 5.9 in (15 cm) Aprox. 1.9 in (5 cm) Marcadores de límite lugares con una elevación inferior a 1.9 in (5 cm) lugares donde haya mecedoras, caminadores, chimeneas, sustancias inflamables o humedad Marcadores de límite Superior a 0.6 in (1.
Uso del control remoto [Tipo A] [Tipo B] 1 1 3 3 1, 2 5 1, 2 5 4 2 4 4 2 4 Consulte la página 23 Consulte la página 23 [Tipo C] 1 3 1, 2 5 6 2 4 4 Consulte la página 24 ESPAÑOL-18
[Tipo A] / [Tipo B]/ [Tipo C] 1 Encendido / Recarga / Inicio/Detención Encendido Enciende/apaga el POWERbot Recarga Seleccione para recargar automáticamente el POWERbot en la estación de carga Inicio/ Detención Seleccione para iniciar o detener el proceso de limpieza 2 Modos de limpieza Limpieza automática Limpieza localizada Limpieza repetida Seleccione para limpiar todas las zonas establecidas una única vez y después regresar automáticamente a la estación de carga.
Uso del control remoto 5 Modo de limpieza manual y Control de dirección Avance Seleccione para desplazarse hacia adelante Giro hacia la izquierda Seleccione para girar hacia la izquierda Giro hacia la derecha Seleccione para girar hacia la derecha ✻ El desplazamiento hacia atrás no está disponible. 6 Limpieza dirigida Disponible únicamente con controles remotos de tipo C. Puede utilizar el control remoto para apuntar y limpiar el punto deseado mientras el POWERbot está en el proceso de limpieza.
Nombre de cada pieza ESPAÑOL-21 Parte superior 1. Visor 2. Receptor de la señal del control remoto 3. Sensor de obstáculos 4. Contenedor de polvo 5. Cámara 6. Botón del contenedor de polvo 7. Sensor de choques 8. Herramienta de activación automática Parte inferior 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
Nombre de cada pieza Visor 1. 2. 3. 4. Programación diaria Modo Normal/Turbo Indicador de batería Botón de limpieza localizada, programación diaria (3 s) 5. Botón Inicio/Detención, modo Turbo (3 s) 6. Botón de recarga ✻ SR1AM70**W* / SR2AM70**W* : Modelo compatible con Wi-Fi ESPAÑOL-22 1. Silenciar 2. Indicador de información 3. *Indicador de encendido/apagado del comando remoto 4.
Ajuste de la hora/programación [Tipo A, Tipo B] solo se puede programar el modo de limpieza automática. Ajuste de la hora Antes de utilizar la programación Una vez/Diaria debe ajustar la hora actual. Inicio del ajuste Seleccione "Hora" Seleccione "Minuto" Ajuste completado Seleccione "AM/PM" Ir al ajuste anterior o siguiente Ajuste de la programación El ajuste o la cancelación de la programación solo puede efectuarse cuando el POWERbot está acoplado a la estación de carga.
Ajuste de la hora/programación [Tipo C] Solo se puede programar el modo de limpieza automática. Ajuste de la hora Antes de utilizar la programación Una vez/Diaria debe ajustar la hora actual. Inicio del ajuste Seleccione "Hora" Seleccione "Minuto" Ajuste completado Seleccione "AM/PM" Ir al ajuste anterior o siguiente Ajuste de la programación El ajuste o la cancelación de la programación solo puede efectuarse cuando el POWERbot está acoplado a la estación de carga.
[Serie SR1AM7010U*] Para los modelos que no incluyen un control remoto, el ajuste de programación es el siguiente. Ajuste de la programación El ajuste o la cancelación de la programación solo puede efectuarse cuando el POWERbot está acoplado a la estación de carga. Presione durante 3 segundos. Cuando se enciende el LED de la programación, se ha configurado la programación diaria. ✻ El tiempo que presiona el botón se establecerá como programación.
Limpieza y mantenimiento Debe apagar el interruptor de emergencia antes de limpiar el POWERbot.
Limpieza del cepillo y de la herramienta de activación automática El diseño del cepillo puede variar según el modelo. No limpie el cepillo con agua. 1 Retire la tapa del cepillo 5 Vuelva a ensamblar el cepillo 2 Retire el cepillo 3 Limpie el cepillo 6 Vuelva a ensamblar la tapa del cepillo 4 Limpie la herramienta de activación automática Limpieza de la rueda motriz 1 Ponga un paño suave en el piso y coloque el POWERbot boca abajo sobre el paño.
Aplicación SmartThings La aplicación SmartThings solo es compatible con modelos que disponen de función Wi-Fi Ajuste del enrutador inalámbrico f Consulte el manual de usuario de su enrutador inalámbrico si tiene problemas de acceso. f El Samsung POWERbot solo admite Wi-Fi 2.4 GHz. f El Samsung POWERbot admite IEEE 802.11b/g/n y Soft-AP. – Se recomienda IEEE 802.11n. f El Samsung POWERbot solo es compatible con el DHCP (Protocolo de configuración de host dinámico).
Descarga de la aplicación SmartThings f Descargue e instale la aplicación SmartThings desde una tienda (Google Play Store, Apple App Store o Samsung Galaxy Apps). Para encontrar la aplicación, use la palabra clave “SmartThings”. Nota f SmartThings es incompatible con tabletas y algunos dispositivos móviles. – Se recomienda Android 6.0 o posterior (al menos 2 GB de RAM). f Es posible que los iPad y algunos dispositivos móviles no se admitan. – iOS 10.0 o posterior / iPhone 6 o posterior se admiten.
Aplicación SmartThings Agregación de un dispositivo a la aplicación SmartThings 1. Conecte su teléfono inteligente al enrutador inalámbrico. – Si el teléfono inteligente no está conectado, active el Wi-Fi en la Settings App y seleccione el enrutador inalámbrico al que se desea conectar. – Desactive la opción de uso de datos móviles del teléfono inteligente para que solo se use el Wi-Fi y conecte un dispositivo. 2. Inicie la aplicación SmartThings en su teléfono inteligente. 3.
Actualización del software f Cuando el POWERbot está cargando en la estación de carga, se conecta al servidor y verifica si hay software disponible. Si encuentra nuevo software, el POWERbot lo descarga automáticamente y lo actualiza. f Si se muestra “UP" en el visor cuando el POWERbot se está cargando, significa que se está realizando una actualización. Espere hasta que se complete la actualización antes de utilizar el POWERbot.
Notas y precauciones f El POWERbot no puede aspirar acumulaciones de polvo y después de la limpieza pueden quedar restos en el piso. Carga Nota – Use otro sistema de limpieza para limpiarlos regularmente. f Si la batería se sobrecalienta durante la carga, puede demorar más en cargarse. f Si la carga automática no funciona, siga los siguientes pasos: – Apague el interruptor de emergencia (en la parte inferior del POWERbot) y vuelva a encenderlo.
f Puesto que el cepillo elimina la suciedad del piso durante la limpieza, pueden quedar atrapados materiales extraños como hilos, cabellos largos, etc. Para obtener los mejores resultados en la limpieza, revíselo y límpielo con regularidad. f Si después del trabajo de mantenimiento no se ensambla correctamente un cepillo o la tapa de un cepillo, puede rayarse el piso o puede causarse un mal funcionamiento del producto. Por lo tanto, instálelos correctamente consultando el método de mantenimiento.
Códigos de información 1 Los tres siguientes indicadores parpadean y suena una alarma de códigos de información.
1 El código de información siguiente se muestra con una alarma de códigos de información. Códigos de información 2 Apague el interruptor de emergencia, lea las siguientes instrucciones y efectúe la acción correspondiente 3 El código de información desaparecerá cuando encienda el interruptor de emergencia Lista de verificación El POWERbot ha quedado trabado, atascado o atrapado cuando se desplazaba.
Solución de problemas Síntoma Lista de verificación El POWERbot no funciona en absoluto. fRevise si el interruptor de emergencia está encendido. fRevise si en el visor aparecen todos los íconos. fRevise si la batería del POWERbot está agotada. – Si se muestra "Lo", coloque el POWERbot en la estación de carga para cargarlo. – Cuando el indicador de la batería parpadee, coloque manualmente el POWERbot en la estación de carga para cargarlo.
Síntoma Lista de verificación He instalado la aplicación SmartThings pero el POWERbot no se conecta. fPuede usar el producto después de conectar el enrutador inalámbrico y el POWERbot con la Configuración fácil de acuerdo con el procedimiento. No consigo iniciar sesión con la cuenta Samsung. fRevise el ID y la contraseña en la pantalla de la cuenta Samsung.
Solución de problemas Síntoma No se puede instalar la aplicación SmartThings. Se muestra un mensaje de error en el registro del producto. Lista de verificación fLa aplicación SmartThings funciona con Android OS 6.0 o posterior, iOS 10 o posterior. fLa versión del sistema operativo que soporta la aplicación SmartThings puede variar en el futuro. fEn el caso de dispositivos inteligentes con rooting, no se garantiza una instalación y un uso estándar.
Síntoma La conexión entre la aplicación SmartThings y el POWERbot se corta repentinamente durante el funcionamiento normal de la aplicación. El control mediante la aplicación SmartThings no funciona porque la función de comando remoto está desactivada. Lista de verificación fSi el POWERbot está alejado del enrutador inalámbrico, la conexión puede cortarse. fRestablezca el POWERbot y el teléfono inteligente y revise nuevamente la conexión.
Aviso de licencia de código abierto El software incluido en este producto contiene software de código abierto. Puede obtener el código fuente correspondiente completo por un período de tres años a partir de nuestro último envío de este producto enviando un correo electrónico a:oss.request@samsung.com. También es posible obtener el código fuente correspondiente completo en un medio físico, tal como un CDROM; se exigirá un cargo mínimo. El siguiente URL http://opensource.samsung.
Especificaciones Clasificación Artículo Tamaño (P x A x L) Peso Especificaciones mecánicas (POWERbot) Sensor Tipo de botones del POWERbot Voltaje Consumo de energía Especificaciones de la batería Tipo de carga Especificaciones de alimentación Modo de limpieza Limpieza Tiempo de carga Tiempo de limpieza Modo Turbo (considerando un Modo normal piso duro) Información detallada SR1AM7010U* SR1AM7040W* 340 mm x 97 mm x 348 mm 4 kg Reconocimiento de la forma del techo (Visio
DJ68-00763C-16