Heat Pump Dryer User manual DV9*M52****/DV8*M52****/DV7*M52****/DV9*M50****/ DV8*M50****/DV7*M50**** Untitled-2 1 2017-03-20 6:23:08
Contents Safety information 4 Contents What you need to know about the safety instructions Important safety symbols Important safety precautions To minimize the risk of fire in a tumble dryer, the following should be observed Critical installation warnings Critical usage warnings Usage cautions Critical cleaning warnings 4 4 5 8 9 11 12 13 Installation 15 What’s included Installation requirements Dryer Drain hose (if necessary) Installation checklist Before using the dryer Door reversal Environment
44 Checkpoints Information codes 44 45 Appendix 46 Fabric care chart Protecting the environment Specification Consumption data 46 47 48 49 Contents Troubleshooting English 3 Untitled-2 3 2017-03-20 6:23:08
Safety information Congratulations on your new Samsung dryer. This manual contains important information on the installation, use, and care of your appliance. Please take the time to read this manual to take full advantage of your dryer’s many benefits and features. What you need to know about the safety instructions Safety information Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur.
Important safety precautions WARNING Safety information To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: 1. This appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. 2.
Safety information 7. For use in Europe: Children of less than 3 years should be kept away unless continuously supervised. Safety information 8. CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility. 9. The tumble dryer is not to be used if industrial chemicals have been used for cleaning. 10.
17. The final part of a tumble dryer cycle occurs without heat (cool down cycle) to ensure that the items are left at a temperature that ensures that the items will not be damaged. 18. Remove all objects from pockets such as lighters and matches. Safety information 19. WARNING: Never stop a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated. 20.
Safety information To minimize the risk of fire in a tumble dryer, the following should be observed CAUTION Safety information Items that have been spotted or soaked with vegetable or cooking oil constitute a fire hazard and should not be placed in a tumble dryer. Oil-affected items can ignite spontaneously, especially when exposed to heat sources such as in a tumble dryer. The items become warm, causing an oxidation reaction in the oil. Oxidation creates heat.
Items such as foam rubber(latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the tumble dryer. Fabric softeners, or similar products, should be used as specified by the fabric softener instructions. Safety information The final part of a tumble dryer cycle occurs without heat(cool down cycle) to ensure that the items are left at a temperature that ensures that the items will not be damaged.
Safety information Remove all foreign substances such as dust or water from the power plug terminals and contact points using a dry cloth on a regular basis. • • Unplug the power plug and clean it with a dry cloth. Failure to do so may result in electric shock or fire. Keep all packaging materials well out of the reach of children, as packaging materials can be dangerous to children. Safety information • If a child places a bag over its head, it may result in suffocation.
This appliance should be positioned so that the power plug, the water supply taps, and the drain pipes are accessible. Critical usage warnings WARNING • • Safety information Do not let children or pets on or into the product. In addition, when disposing of this product, disassemble the door lock (lever). This may result in children falling and injuring themselves. If children become locked in the product, there is a danger of suffocation.
Safety information Do not attempt to repair, disassemble, or modify the appliance yourself. • • • Do not use any fuse(such as cooper, steel wire, etc.) other than the standard fuse. When repairing or reinstalling the appliance is required, contact your nearest service center. Failure to do so may result in electric shock, fire, problems with the product, or injury. The product you have purchased is designed for domestic use only.
Do not dry clothing with large buckles, buttons, or other heavy metal (zippers, hooks and eyelets, button-up covers). If necessary, use the laundry net for small and lightweight laundry such as fabric tie belt , apron strings, and underwire bras which can dissolve or break during a cycle. Recommend against using drying sheets to reduce static electricity as this could lead to damage to your laundry and also potential damage to the appliance. This may result in damage to the laundry.
Safety information Clean the Heat Exchanger with a soft brush or vacuum cleaner once a month, Do not touch the heat exchanger with your hand. Otherwise, it may cause an injury. The interior of the dryer should be cleaned periodically by qualified service personnel.
Installation What’s included Carefully unpack the dryer. Keep all packaging materials away from children. The parts and location of parts shown below may differ from your dryer. Before installation, make sure the dryer has all the parts listed here. If the dryer and/or parts are damaged or missing, contact the nearest Samsung customer service center.
Installation Accessories (supplied) Installation Hose guide Cable tie Hose connector Long drain hose (2 m) User manual Rack Dry (applicable models only) Accessories (not supplied) Bracket-Stacking kit (Part # SK-DH; SK-DA; SKKDF) Stacking kit (SKK-DD, SKK-DDX) NOTE • • • The stacking kit allows the dryer to be stacked on top of a washer. Please note that the stacking kit can only be used with Samsung washers and dryers.
Installation requirements NOTE This dryer must be installed by a qualified installer. If service is required due to poor or faulty installation, it is considered the owner’s responsibility and may void the warranty. Keep these instructions for future reference. WARNING • • • • • • • • Installation • • Do not plug the power cord into a wall outlet before the dryer is completely installed. Have two or more persons help move the dryer. Do not let children or pets play in, on, or around the dryer.
Installation Location requirements Select a level, well-constructed surface that will withstand vibrations. Select a location where a grounded, 3-prong outlet is easily accessible. WARNING • • • • • Install the dryer indoors only. Do not install the dryer in areas exposed to the weather. Do not install the dryer where the temperature may fall below 5 °C or rise above 35 °C. Do not install the dryer where gas may leak. Do not block the cooling grill’s air inlet located at the dryer front.
Dryer Before you install the dryer, make sure you have read Installation requirements on page 17. Please note that the following instructions are for installation without using a drain hose. For instructions for using a drain hose, see the next section, Drain hose. For convenience, consider installing the dryer next to your washer. 1. Gently slide the dryer into the desired location. A 2. Use a level (A) and check the levelness of the dryer from side to side and front to back. Installation 3.
Installation Drain hose (if necessary) The dryer comes with a built-in water tank. However, if you do not want to use the water tank, you may install the drain hose. The provided accessory hose (long drain hose) can be used as an extension to the drain hose. Installation 1. Remove the drain hose from hole (A), and insert it into hole (B).
2. Insert one end of the accessory hose (long drain hose) into hole (A). 3. Insert the other end (outlet) of the accessory hose to the drainage system in one of the following ways: A Over a wash basin: Installation 1. Make sure to place the end of the accessory hose lower than 90 cm (*) from the bottom of dryer. 2. To bend some point of the accessory hose, use the supplied plastic hose guide (B) and secure the guide to the wall with a hook or to the tap with a piece of string.
Installation By using the drain pipe of the wash basin: 1. Assemble the hose connector (A), and attach it to the end of the accessory hose as shown. A CAUTION To prevent water leak, make sure to connect the hose and the connector firmly. Installation 2. Connect the hose adapter directly to the drain pipe of the wash basin.
Installation checklist • • • • • • The dryer is plugged into a properly grounded outlet. All packaging material is completely removed and properly disposed. The dryer is level and standing firmly on the floor. Start the dryer to make sure that it runs, heats, and shuts off. Run a TIME DRY cycle for 20 minutes to see if the HC information code is displayed. If this is the case, contact a local service center. After installation, we recommend that you wait at least 1 hour before using the dryer.
Installation Door reversal You might want to reverse the direction of the door, depending on your site conditions or to your needs. WARNING Make sure door reversal is performed by a qualified technician. 1. Open the door, and then loosen the two screws on the door hinge. While holding the door with both hands, slightly lift to remove it. Installation 2. Use a thin object to remove the door sealing. 3.
4. When complete, rotate the door cover by 180 degrees. Installation 5. Insert the glass holder into the new position of the door cover. Make sure the door hinge is in the same position as in the figure. 6. Tighten the upper 3 screws and the lower 3 screws on the glass holder. NOTE The screw shapes differ by dimension. Make sure you tighten the correct screw.
Installation 7. Insert the door sealing in the correct position. Installation 8. Remove the 2 screws that remain after removing the door hinge. 9. Loosen the 4 screws on the lever holder. Remove the lever holder, and then reinsert it to the opposite side.
10.On the opposite hinge frame, tighten the removed 2 screws in step 7 above. Note that you must tighten them on the right (top-right and bottom-right) of the frame. Installation 11.Put the door hinge on the opposite side, and then tighten the 2 screws to fix the door to the dryer. NOTE To return the door to the initial position, follow the steps again. Please note that the door, hinges, and other parts would be in the opposite orientation as listed in these steps.
Operations Control panel DV9*M5*****/DV8*M5***** 12 01 10 11 02 09 03 04 05 06 07 DV7*M5***** 12 Operations 01 10 11 02 09 03 04 05 06 08 28 English Untitled-2 28 2017-03-20 6:23:12
Displays all cycle information, including cycle time, information codes, and dryer status. See the table below for status details. 01 Digital Graphic Display Drying in progress Child Lock activated/ deactivated Cooling in progress Wrinkle Prevent Stop Heat-exchanger clean alarm Wrinkle Prevent in progress Sound on/off Check filter Mixed Load Bell Delay End Smart Check Empty the water tank Turn the dial to select a cycle. See the Cycle overview on page 31 for available cycles.
Operations Operations 06 Mixed Load Bell This alarm is available only with SHIRTS, COTTON, MIXED LOAD, and SYNTHETICS cycle. If a load contains mixed fabrics, the Mixed Load Bell indicator ( ) blinks when the average dryness of the item is 80 % dry. This lets you take items that you don’t want fully dried or that dry quickly out of the dryer early while letting others continue to dry. 07 Lamp (DV9*M5*****/ DV8*M5*****) Press to turn on or off the interior lamp.
Cycle overview Cycle Description Max load (kg) SHIRTS Use to quickly dry one item such as a shirt. 4 IRON DRY This cycle finishes the drying process in a moist state, which facilitates ironing. 4 DELICATES For items to be handled with care such as lingerie. 2 WOOL For machine washable and tumble dryable wool only. For best results, turn laundry inside out before drying. 2 Use to dry loads such as bath towels. 6 BEDDING For bulky items such as blankets, sheets, comforters, and light duvets.
Operations Cycle Description Max load (kg) Use to set a desired dry time. 1. Turn the Cycle Selector to select TIME DRY. TIME DRY 2. Press Time to set the drying time between 30 minutes and 150 minutes. Keep pressing Time cycles through the available time options in 30-minute increments. - NOTE The actual cycle time may differ depending on the dryness of items. Operations QUICK DRY 35' For drying light cotton synthetics or items that needs quick drying. The default dry time is 35 minutes.
Cycle chart NOTE For best results, follow the load size recommendations for each dry cycle. • • • Large load: Fill the drum to about ¾ full. Do not add items over this level as they need to tumble freely. Medium load : Fill the drum to about ½ full. Small load : Fill the drum with 3-5 items, not more than ¼ full. Cycle Recommended items SHIRTS Non-iron shirts or blouses made of cotton, linen, synthetic fibres or blended fabrics.
Operations Getting started Simple steps to start 1. Press Power to turn the dryer on. 2. Load the dryer and close the door. 3. Turn the Cycle Selector to select a cycle. 4. Change the cycle settings (Dry Level, and Time) as necessary. 5. Select necessary settings and options to your preference. (Wrinkle Prevent, Lamp, Mixed Load Bell, and/or Delay End). 6. Press Start/Pause. The dryer indicator lights up, and the estimated cycle time appears on the display.
Rack Dry (applicable models only) Set the drying time up to 150 minutes according to the moisture and weight of the items to dry. When drying laundry using the drying rack, the TIME DRY cycle is recommended. 1. Position the drying rack in the drum, inserting the front lips of the rack into the holes of the door diaphram. Operations A 2. Place items on the rack, leaving enough space where air can circulate. For clothing items, fold and place flat on the rack.
Operations Drying suggestions Items (max 1.5 kg) Washable sweaters (block to shape and lay flat on rack) Stuffed toys (cotton or polyester fiber filled) Description When drying the laundry using the rack, fold and place the clothes on the rack to prevent the clothing from becoming wrinkled. Stuffed toys (foam or rubber-filled) Foam rubber pillows Sneakers To dry sports shoes, place the shoes on the rack so that the soles of the shoes are facing downwards.
Cycle guide Always follow the care label when drying. If care label instructions are not available, refer to the following table. • Use the High temperature settings. Blankets • For best results, dry only one blanket at a time. Cloth diapers • Use the High temperature settings. Down-filled items • Do not dry on a heat setting. Doing so may cause a fire hazard. Only use the COOL AIR cycle. Foam rubber (rug backs, stuffed toys, etc.) • Do not dry on a heat setting.
Operations Special features Delay End Smart Check You can set the dryer to complete a selected cycle at your set time. If the dryer has detected an issue, Smart Check allows you to check the status of the dryer using a smartphone. Please note that Smart Check can only be used for Galaxy and iPhone series smartphones. 1. Select a cycle with necessary options. 2. Press Delay End repeatedly to set a time between 1 hours and 24 hours in 1-hour increments. 3. Press Start/Pause.
Maintenance WARNING • • • Do not clean the dryer by directly spraying water onto the dryer. Do not clean the dryer with benzene, thinner, alcohol, or acetone. This may cause discoloration, deformation, damage, electric shock, or fire. Before cleaning the dryer, be sure to unplug the power cord. Control panel Clean with a soft, damp cloth. Do not use abrasive cleaners. Do not spray cleaners directly on the panel. Immediately wipe up any spills or liquids from the control panel.
Maintenance 2. Open the outer filter and remove the inner filter (A). A 3. Unfold both the inner filter and the outer filter. 4. Remove the lint from both filters, and then clean them in running water. When complete, dry them thoroughly. Maintenance 5. Put the inner filter into the outer filter, and then reinsert the lint filter into the original position. CAUTION • • • Clean the lint filter after each load. Otherwise, the drying performance may decrease.
Water tank To avoid leaks, empty the water tank after every load. 1. Using both hands, pull the water tank (A) forward to remove. A 2. Empty the water through the drain hole (B) and place the water tank back into place. NOTE B If you empty the water tank and press Start/Pause, the corresponding indicator turns off.
Maintenance Heat exchanger Clean the heat exchanger at least once a month. As a reminder, the heat exchanger indicator lights up on the display when the heat exchanger needs to be cleaned. 1. Gently press the top part of the outer cover (A) to open. A 2. Unlock the fixers (B). B Maintenance 3. Remove the inner cover (C).
4. Clean the heat exchanger with a soft brush or vacuum cleaner. CAUTION • • • To avoid physical injury and burns, do not touch or clean the heat exchanger with bare hands. Do not use water to clean the heat exchanger. Do not exert force to the heat exchanger. You may damage the heat exchanger which may lead to a decrease in drying performance. 5. Clean the inner cover with a smooth, damp cloth. Maintenance 6. Reinsert the inner cover to its original position, and then lock the fixers. 7.
Troubleshooting Checkpoints If you encounter an issue with the dryer, first check the table below and try the suggestions. Symptom Dryer does not run Dryer does not heat Action • • • • • Make sure the door is completely closed. Make sure the power cord is plugged in. Check the home’s circuit breaker and fuses. Empty the water tank. Clean the lint filter. • • • Check the home’s circuit breaker and fuses. Select a heat setting other than COOL AIR. Check the lint filter and heat exchanger filter.
Symptom Action • • • Make sure the lint filter is clean before every load. Dry lint-producing items (fuzzy towels) separate from lint trappers, such as black linen pants. Divide larger loads into smaller loads. Items still wrinkled after Wrinkle Prevent • • Small loads of 1-4 items work best. Load fewer items. Load similar type items. Odors remain in items after Cool Air • Make sure to thoroughly wash items with strong odors.
Appendix Fabric care chart The following symbols provide garment care direction. The Clothing care labels include symbols for drying, bleaching, drying and ironing, or dry cleaning when necessary. The use of symbols ensures consistency among garment manufacturers of domestic and imported items. Follow care label directions to maximize garment life and reduce laundering problems.
Iron dry or steam temperatures Dry-clean High Dry-clean Medium Do Not dry-clean Low Line Dry/ Hang to Dry Warning symbols for laundering Do Not Wash Drip Dry Dry Flat Do Not Wring Do Not Bleach Do Not Tumble Dry No Steam (added to iron) Do Not Iron Protecting the environment This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance, please observe local waste disposal regulations.
Appendix Specification E D A C B DV9*M52****, DV8*M52****, DV7*M52**** TYPE DIMENSIONS FRONT LOADING DRYER A 600 mm B 850 mm C 600 mm D 640 mm E 1095 mm 50 kg WEIGHT ELECTRICAL REQUIREMENTS Appendix ALLOWABLE TEMPERATURE 220–240 V / 50 Hz 550-600 W 5-35 °C 48 English Untitled-2 48 2017-03-20 6:23:19
DV9*M50****, DV8*M50****, DV7*M50**** TYPE FRONT LOADING DRYER DIMENSIONS A 600 mm B 850 mm C 600 mm D 640 mm E 1095 mm 50 kg WEIGHT ELECTRICAL REQUIREMENTS 220–240 V / 50 Hz 750-850 W 5-35 °C ALLOWABLE TEMPERATURE Consumption data Model Energy (kWh) Max. Duration (Minutes) 9 1.56 188 4.5 0.9 130 IRON DRY** 9 1.1 130 SYNTHETICS 4.5 0.71 86 8 1.43 169 4 0.8 120 IRON DRY** 8 1.02 118 SYNTHETICS 4 0.65 80 7 1.26 148 3.5 0.73 110 IRON DRY** 7 0.
Appendix Model Load (kg)* Energy (kWh) Max. Duration (Minutes) 9 2.20 190 4.5 1.12 130 IRON DRY ** 9 1.70 155 SYNTHETICS 4.5 0.85 78 8 1.87 170 4 1.10 125 IRON DRY ** 8 1.54 140 SYNTHETICS 4 0.78 72 7 1.67 150 3.5 1.00 120 IRON DRY ** 7 1.43 130 SYNTHETICS 3.5 0.
Memo Untitled-2 51 2017-03-20 6:23:20
QUESTIONS OR COMMENTS? COUNTRY CALL OR VISIT US ONLINE AT AUSTRALIA 1300 362 603 www.samsung.com/au/support NEW ZEALAND 0800 726 786 www.samsung.