NETWORK CAMERA User Manual XNV-9082R/XNV-8082R XND-9082RV/XND-8082RV XND-9082RF/XND-8082RF XNO-9082R/XNO-8082R XNB-9002/XNB-8002
Network Camera User Manual Copyright ©2020 Hanwha Techwin Co., Ltd. All rights reserved. Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
overview IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth. (Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.) 7.
overview Class construction An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection. Battery Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. The battery cannot be replaced. Disconnection Device Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location. When used outside of the U.S.
CONTENTS OVERVIEW 6 8 Important Safety Instructions Recommended PC Specifications Recommended Micro SD/SDHC/SDXC Memory Card Specifications NAS recommended specs Optional Accessories for Installation OUTDOOR VANDAL DOME CAMERA 9 9 10 What’s Included At a Glance Installation INDOOR DOME CAMERA 17 17 18 What’s Included At a Glance Installation 24 24 25 What’s Included At a Glance Installation 31 31 32 What’s Included At a Glance Installation 3 9 17 FLUSH MOUNT DOME CAMERA 24 OUTDOOR BULLET CA
overview RECOMMENDED PC SPECIFICATIONS NAS RECOMMENDED SPECS •• CPU : Intel(R) Core(TM) i7 3.4 GHz or higher •• RAM : 8G or higher •• Supported OS : Windows 8.1 or later, Mac OS X 10.13 or later •• Recommended browser: Google Chrome Supported browsers: MS Explorer11, MS Edge, Mozilla Firefox (Window 64bit only), Apple Safari (Mac OSX only) •• Recommended capacity : 200GB or higher is recommended. •• For this camera, you are recommended to use a NAS with the following manufacturer’s specs.
Outdoor Vandal Dome Camera Indoor Dome Camera XNV-9082R/XNV-8082R Flush Mount Dome Camera XND-9082RV/XND-8082RV XND-9082RF/XND-8082RF ●● OVERVIEW 17 9 Outdoor Bullet Camera XNO-9082R/XNO-8082R 31 24 Box Camera XNB-9002/XNB-8002 38 English _7
overview OPTIONAL ACCESSORIES FOR INSTALLATION Model name Hanging Mount XNV-9082R/XNV-8082R SBP-187HMW of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power You can purchase appropriate optional accessories available.
WHAT’S INCLUDED As for each sales country, accessories are not the same. ●● OUTDOOR VANDAL DOME CAMERA of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection.
outdoor vandal dome camera INSTALLATION 2. Take off the lens cover protecting the camera lens. camera is waterproof and in compliance with the IP67 / IP6K9K spec, but the jack connected to the external cable is not. JJ `` This You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Removing a Micro SD card Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD card from the slot. Installation (mount plate) [Directly installing on wall/ceiling] 1-1. Attach the installation template on the desired surface and drill holes for screws and cables. ●● OUTDOOR VANDAL DOME CAMERA removing the Micro SD card, in , set the device to and press the [Apply] button and turn the JJ `` Before camera off.
outdoor vandal dome camera [Installing using pipe] 2-1. Attach the installation template and drill holes for screws and cables. 2-2. Separate the pipe cover of the mount plate by pressing its sides. 2-3. Place the pipe on the mount plate. 2-4. Fix the mount plate using appropriate screws. 2-5. Pull out necessary cables among network/power/audio/alarm cables through the pipe. Installation (camera case) JJ `` Use a cable bushing compliant with the network cable to be connected.
1-4. Mount the cable bushing to the camera case. 2-3. Mount the cable bushing to the camera case. ●● OUTDOOR VANDAL DOME CAMERA [Installing the network cable] (IP66) 2-1. Pull off the extruded part of the 1-hole cable bushing provided. 2-2. Use the cap installer to pass through the RJ45 cable. [Installing audio/alarm cables] 3-1. Mount the cable bushing of the provided audio/alarm cables to the camera case.
outdoor vandal dome camera Installing the camera module 4. Join the mount plate with the camera case. 1. Connect the network/power/audio/alarm cables to the camera module terminal. 2. Attach the camera module to the case. JJ `` A magnet is embedded at the bottom of the module 2x `` Take caution not to allow any foreign objects between the attaching surfaces. x4 TR20 * AC 3. Adjust the lens to the desired direction with reference to “Adjusting the monitoring direction for the camera” section.
Assembling the dome cover [Using Weather cap] 1. Remove the screws from the dome cover. [Directly installing on wall/ceiling] 1. Assemble the dome cover. JJ `` Make sure to firmly tighten the fastening screws so that there is no water damage issue. 4x ●● OUTDOOR VANDAL DOME CAMERA 2x TR20 x4 TR20 2. Assemble the dome cover. 3. Mount the weather cap to the dome cover and fasten the screws. JJ `` Make sure to firmly tighten the fastening screws so that there is no water damage issue.
outdoor vandal dome camera Outdoor installation When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside. 1. Connect the power, I/O, and network cables. 2. Wrap the black cable jacket (Area A) and the cable connection area with waterproof (butyl rubber) tape so that more than half of the butyl rubber tape is overlapped.
WHAT’S INCLUDED ●● INDOOR DOME CAMERA Camera-module d Dome-cover e of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power Control Button Port of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection.
indoor dome camera INSTALLATION 2. Take off the lens cover protecting the camera lens. camera is waterproof and in compliance with the IP52 spec, but the jack connected to the external cable is not. You are JJ `` This recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Removing a Micro SD card Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD card from the slot. Installation (mount plate) [Directly installing on wall/ceiling] 1-1. Attach the installation template on the desired surface and drill holes for screws and cables. ●● INDOOR DOME CAMERA removing the Micro SD card, in , set the device to and press the [Apply] button and turn the JJ `` Before camera off.
indoor dome camera [Installing using pipe] 2-1. Attach the installation template and drill holes for screws and cables. 2-2. Separate the pipe cover of the mount plate by pressing its sides. 2-3. Place the pipe on the mount plate. 2-4. Fix the mount plate using appropriate screws. 2-5. Pull out necessary cables among network/power/audio/alarm cables through the pipe. Installation (camera case) JJ `` Use a cable bushing compliant with the network cable to be connected.
1-4. Mount the cable bushing to the camera case. 2-3. Mount the cable bushing to the camera case. ●● INDOOR DOME CAMERA [Installing the network cable] 2-1. Pull off the extruded part of the 1-hole cable bushing provided. 2-2. Use the cap installer to pass through the RJ45 cable.
indoor dome camera [Installing audio/alarm cables] 3-1. Mount the cable bushing of the provided audio/alarm cables to the camera case. Installing the camera module 1. Connect the network/power/audio/alarm cables to the camera module terminal. 2. Attach the camera module to the case. JJ `` A magnet is embedded at the bottom of the module `` Take caution not to allow any foreign objects between the attaching surfaces. 3. Connect the microphone cable to the camera module. 4.
Assembling the dome cover [Directly installing on wall/ceiling] 1. Assemble the dome cover. ●● INDOOR DOME CAMERA JJ `` Make sure to firmly tighten the fastening screws so that there is no water damage issue. 4x x4 TR20 JJ `` Be careful not to alter the monitoring direction of your camera.
WHAT’S INCLUDED a Bracket As for each sales country, accessories are not the same. of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power d Dome-cover of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power Control Button port j Zoom/Focus i Reset button of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection.
INSTALLATION 2. Take off the lens cover protecting the camera lens. camera is waterproof and in compliance with the IP52 spec, but the jack connected to the external cable is not. You are JJ `` This recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
flush mount dome camera Removing a Micro SD card Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD card from the slot. removing the Micro SD card, in , set the device to and press the [Apply] button and turn the JJ `` Before camera off. `` If you turn off the camera or remove the Micro SD card that contains data from the product, the data may be lost or damaged. Installation (housing) 1.
3. Connect the safety cable. JJ `` A safety cable is not provided. 4-2. Pull out necessary cables among network/power/audio/alarm cables through the pipe. ●● FLUSH MOUNT DOME CAMERA e.g. [Using pipe] 4-1. Install the pipe in a fitting hole.
flush mount dome camera Installation (camera case) JJ `` Use a cable bushing compliant with the network cable to be connected. -- Components: use a cable with the diameter of Ø5 to 8.5 [Installing network/power cables] [Installing the network cable] 2-1. Pull off the extruded part of the 1-hole cable bushing provided. 2-2. Use the cap installer to pass through the RJ45 cable. Cap Installer 1-1. Pull off the extruded parts of the cable bushing to be used. 1-2.
[Installing audio/alarm cables] 3-1. Mount the cable bushing of the provided audio/alarm cables to the camera case. Installing the camera module 1. Connect the network/power/audio/alarm cables to the camera module terminal. 2. Attach the camera module to the case. ●● FLUSH MOUNT DOME CAMERA JJ `` A magnet is embedded at the bottom of the module `` Take caution not to allow any foreign objects between the attaching surfaces. 4. Turn the screws on the housing to fix the housing to the ceiling.
flush mount dome camera Assembling the dome cover Waterproofing cables JJ `` Make sure to firmly tighten the fastening screws so that there is no water damage issue. 1. Connect the power, I/O, and network cables. If there is any possibility of moisture intrusion through the gap of the cable, please waterproof the concerned area with waterproof butyl rubber tape (can be purchased in stores) as below. 1. Assemble the dome cover. 4x 2.
outdoor bullet camera WHAT’S INCLUDED AT A GLANCE As for each sales country, accessories are not the same. Pipe-cover b Mount plate d c e Bottom cover f Sunshield Camera body i Reset button of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power f Network port Sunshield fixing screw of the Be ware CAUTION: and Polarity Rated Voltageconnection.
outdoor bullet camera INSTALLATION JJ `` This camera is waterproof and in compliance with the IP67 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed. Removing a Micro SD card Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD card from the slot.
Installation (Mount plate) [Directly installing on wall/ceiling] [Installing using pipe] 2-1. Attach the installation template and drill holes for screws and cables. 1-1. Attach the installation template on the desired surface and drill holes for screws and cables. ●● OUTDOOR BULLET CAMERA 2-2. Separate the pipe cover of the Mount plate by pressing its sides. 1-2. Fix the Mount plate using appropriate screws. 1-3.
outdoor bullet camera 2-3. Place the pipe on the Mount plate. 2-4. Fix the Mount plate using appropriate screws. 1-4. Mount the cable bushing to the Bottom cover. 2-5. Pull out necessary cables among network/power/audio/alarm cables through the pipe. Installation (Bottom cover) JJ `` Use a cable bushing compliant with the network cable to be connected. -- Camera main: use a cable with the diameter of Ø5 to 6.5 -- Components: use a cable with the diameter of Ø5 to 8.
2-3. Mount the cable bushing to the Bottom cover. 4. Join the Mount plate with the Bottom cover. ●● OUTDOOR BULLET CAMERA 3x HEX x4 S3 [Installing audio/alarm cables] 3-1. Mount the cable bushing of the provided audio/alarm cables to the Bottom cover.
outdoor bullet camera Installing the camera module 1. Hang the safety cable up on a hook that looks like an arrow in the Bottom cover. 3. Attach the camera body to the Bottom cover. JJ `` Make sure to firmly tighten the fastening screws so that there is no water damage issue. 3x x4 HEX S3 e.g. 2. Connect the network/power/audio/alarm cables to the camera module terminal. 36_ outdoor bullet camera 4. Adjust the camera direction using the Hex. L wrench provided.
5. Assemble the sunshield to the camera body using sunshield fixing screw. Outdoor installation When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside. 2. Wrap the black cable jacket (Area A) and the cable connection area with waterproof (butyl rubber) tape so that more than half of the butyl rubber tape is overlapped.
box camera WHAT’S INCLUDED AT A GLANCE As for each sales country, accessories are not the same. b Mounting Bracket Screw Hole a CS mount Lens (not included) c l Test monitor out port k Audio cable port d Micro SD card Compartment e GND AUDIO OUT RESET VIDEO Option (not included) AUDIO IN USB FOCUS NETWORK 123456 of the Be ware CAUTION: and Polarity Rated Voltageconnection.
MOUNTING THE LENS Disconnect the power before proceeding. Focusing Select a target to film, turn the zoom lever of the lens to adjust the magnification and then focus the lens so that target is clearly displayed. Mounting the CS mount Lens on a camera Turn the CS mount Lens clockwise to attach it. CS mount Lens focusing with the zoom lever of the lens, press the [FOCUS] button on the rear of the camera to adjust the lens even MM `` After more clearly.
VIDEO USB FOCUS NETWORK box camera 123456 INSERTING/REMOVING A MICRO SD CARD Inserting a Micro SD card Insert a Micro SD card in the arrow direction shown in the figure. AUDIO OUT 1 : ALARM 1 4 : NC 2 : ALARM 2 5 : RS-485 + 3 : GND 6 : RS-485- PoE AUDIO OUT AC 24V DC 12V RESET VIDEO Removing a Micro SD card VIDEO AUDIO OUT Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD card from the slot.
installation & connection ADJUSTING THE MONITORING DIRECTION FOR THE CAMERA JJ `` Adjust the direction of IR LEDs not to hinder their view by an instrument. JJ `` Adjust the direction of IR LEDs not to hinder their view by a weather cap (if any). ●● INSTALLATION & CONNECTION Tilt Pan Lens rotation `` Adjusting the monitoring direction You can adjust the camera direction only when the camera is fixed on the ceiling.
installation & connection CONNECTING WITH OTHER DEVICE WiFi dongle WiFi dongle SOFT AP SOFT AP Monitor for installation AUDIO OUT RESET AUDIO IN USB VIDEO FOCUS NETWORK Grounding cable Power 123456 1 : ALARM 1 4 : NC 2 : ALARM 2 5 : RS-485+ 3 : GND 6 : RS-485- PoE AC 24V DC 12V Ethernet Power Monitor for installation Monitor for installation Ethernet Power SOFT AP 42_ installation & connection
Ethernet Connection Connect the Ethernet cable to the local network or to the Internet. Connecting WiFi 1. Connect OTG adapter (5-pin) and WiFi dongle to the micro USB port. Smartphone Setup 2. Select the camera SSID after turning on the WiFi. 3. Run the Wisenet Installation application. 4. When you log in to the camera, the video will be connected. `` The video will be played without being logged in during the initial connection. 5.
installation & connection Connecting to Audio Input/Output •• Audio Codec PC Speaker Microphone Network -- Audio In : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz), G.726 ADPCM (Bit Rate: 16Kbps, 24Kbps, 32Kbps, 40Kbps / Sampling Frequency: 8kHz), AAC (Bit Rate: 48Kbps / Sampling Frequency: 16kHz) -- Audio Out : G.
Connecting to the I/O port box NETWORK Connect the Alarm I/O cable to the corresponding port of the port box. + 1 2 3 4 5 6 AUDIO OUT AUDIO IN LINK FOCUS VIDEO 1 : ALARM 1 2 : ALARM 2 3 : GND NETWORK 4 : NC 5 : RS-485+ 6 : RS-485- PoE 1 2 3 4 5 6 1 : ALARM 1 2 : ALARM 2 3 : GND + AC 24V DC 12V 4 : NC 5 : RS-485+ 6 : RS-485- PoE AC 24V DC 12V Sensor Alarm (Warning lamp) •• ALARM #1, ALARM #2 : T hese ports can be used as alarm input or output ports.
installation & connection To connect the external sensor Connect one of the 2 signal lines to the [ALARM #1] port (if you want this to be the input port) and the remaining one to the [GND] port. Alarm In Wiring Diagram External connection Inside of the camera VCC_3.3V RESISTOR Sensor ALARM #1(5 mA SINK) RESISTOR RESISTOR MLCC GND DIODE TRANSISTOR GND To connect the alarm out If devices (e.g.
network connection and setup You can set up the network settings according to your network configurations. CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE MODEM INTERNET 1. Launch an Internet browser on the local PC. DSL/Cable Modem 2. Enter the IP address of the camera in the address bar of the browser. DDNS Server (Data Center, KOREA) Camera Camera External Remote PC Camera 1. Connect the user PC directly with the network camera.
network connection and setup USING DEVICE MANAGER MM `` Device manager program can be downloaded from - menu at Hanwha Techwin website (http://www.hanwha-security.com). `` More instructions of Device Manager can be found at menu of the main page. AUTOMATICALLY SEARCHING CAMERA If a camera is connected to the same network of the PC where device manager is installed, you can find network camera by using search function. 1.
Configuring Dynamic IP Receive IP address from DHCP -- If connecting the camera directly to modem using the DHCP protocols -- If IPs are assigned by the internal DHCP server via the LAN 1. Click the camera from the list that you want to change the IP setting. 1. Click the camera from the list that you want to automatically configure the IP. XNV-9082R 2. Click < + > at the main page of device manager. •• Equipment Setting menu appears.
network connection and setup PORT RANGE FORWARD (PORT MAPPING) SETUP If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the Broadband Router so that a remote PC can access the camera in it. Manual Port Range Forwarding 1. From the Setup menu of the Broadband Router, select - . For setting the port range forward for a third-party Broadband Router, refer to the user guide of that Broadband Router. 2.
CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 1. Run device manager. It will scan for connected cameras and display them as a list. ●● NETWORK CONNECTION AND SETUP 2. Double-click a camera to access. The Internet browser starts and connects to the camera. MM `` Access to the camera can also be gained by typing the camera’s IP address in the address bar of the Internet browser.
web viewer CONNECTING TO THE CAMERA Normally, you would 1. Launch the Internet browser. 2. Type the IP address of the camera in the address bar. ex) • IP address (IPv4) : 192.168.1.100 http://192.168.1.100 - the Login dialog should appear. • IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111 http://[2001:230:abcd:ffff:0000:0000:ffff:1111] - the Login dialog should appear. If the HTTP port is other than 80 1. Launch the Internet browser. 2.
PASSWORD SETTING When you access the product for the first time, you must register the login password. characters. For a password with 10 to 15 digits, you must use at least 2 types of those mentioned. -- Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].?/ 1. Click the [Setup ( )] icon. 2. The Settings window appears. 3. You can configure settings for the camera’s basic information, video, audio, network, event, analysis, and system over the network. 4.
appendix TROUBLESHOOTING PROBLEM When an Windows 10 user accesses the web viewer through Chrome or Firefox, the sound volume of microphone changes periodically. What are the specifications for WAVE files necessary to play audio at the time of an event? No video is displayed when accessing the plug-in free webviewer on Safari via HTTPS. I can’t access the camera from a web browser. Viewer got disconnected during monitoring.
Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.