User Manual

setup screen
38_ setup screen
To Setup Special
1. Select <Special>.
2. Select each item and set it properly.
• Sharpness : Adjust the overall sharpness of the image.
If selecting <On>, you can adjust the sharpness of the
image.
• Sharpness level : The higher the level is, the sharper and
clearer the outline of the image becomes.
• Gamma : Adjust the contrast of the image.
• Contrast : Adjusts the difference between the darkest area and the brightest area in the video.
• Color level : Adjust the strength of video color.
• Defog : Compensate the video in the foggy or cloudy weather.
It is set to <Off> as a default. Specials are used when the video looks blurry in the foggy weather.
- Off : Disable the fog elimination function.
- Auto : The image is automatically compensated according to the foggy level. Adjust <Defog level>
to be more effective.
- Manual : The user manually sets the amount of compensation for each image.
J
`
If the defog mode is set to <Auto>, the performance is proportional to the fog level. To keep the set defog level without
regard to the fog level, set the defog mode to <Manual>.
`
If the manual defog level is high in a thin fog, the image may become too dark.
• Defog level : Control the defog level.
To Set OSD
1. Select <OSD>.
2. Select each item and set it properly.
• Camera title : It specifies the name of the camera to be
displayed on the screen.
Select the <Use> check box to add a camera name.
- Add : Click the <Add> button and you can add a
total of 5 lines, 17 characters per line and a total of 85
characters.
- Preview : Click the <Preview> button to check the name of camera that will be displayed on the
screen.
• Camera title X, Y : It specifies the position of the camera name on the screen.
• Date & time : Set the time display and date formats on the screen.
• Date & Time X, Y : Specify the position of time display on the screen.
• Weekday overlay : Specify the use of date display date on the screen.
• Size : Sets the size of OSD to small/medium/large.
• Color : Sets the color of the OSD to white/red/blue/green/black/gray.
• Transparency : Sets the transparency of OSD to opaque / low / middle / high.
J
`
A position-adjustable item (Camera title, Date & Time) may not be displayed normally if it overlaps with another fixed OSD item.
`
Multilingual other than English: Input only in the selected language is available.
To set the heater
1. Select <Heater>.
When frost forms, the user can click the button and turn on
the heater for 30 minutes to remove the frost.
J
`
At low temperature when frost is likely to form, the heater is always on; at a high temperature where the product can be
affected by it, it does not operate, even when the request to operate has been sent.
`
This only applies to XNF-8010RV/RVM
To Set IR
1. Select <IR>.
2. Select each item and set it properly.
• Mode : When the IR indicator turns on in B/W mode, the
screen will be protected from saturation on the center area
so that you can identify a short-distant object.
- Off : IR mode will be disabled.
- Auto1 : Adjust the IR brightness according to the brightness of the object on the center screen.
- Auto2 : The brightness of the IR is automatically adjusted according to the brightness of the object
located in the middle or periphery of the screen.
- Manual : Adjust the IR brightness manually.
• Level : Adjust the level of IR in manual mode.
Smart codec
Set a desired area of the video incoming from the camera as ROI area and specify the detection sensitivity for
the area.
1. From the Setup menu, select the <Video & Audio (
)>
tab.
2. Click <Smart codec>.
3. Set the image quality.
The ROI area will be displayed in the specified quality.
4. Specify an area of interest to monitor manually.
5. Select a desired area with the mouse pointer, and drag it as
much as you want.
`
You can specify up to 5 distinct areas.
6. To cancel all the settings for the area, click the [Clear] button.
7. When done, click [Apply].
J
`
The Smart codec will not be active if it is set to <Off> in <Video profile>. (page 29)