NETWORK CAMERA User Manual XNF-9010RS
Network Camera User Manual Copyright ©2021 Hanwha Techwin Co., Ltd. All rights reserved. Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
overview IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 23. This device has been verified using STP cable. The use of appropriate GND grounding and STP cable is recommended to effectively protect your product and property from transient voltage, thunderstroke, communication interruption. 2. Keep these instructions. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.
overview Class construction Please read the following recommended safety precautions carefully. An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection. ~ Do not place this apparatus on an uneven surface. ~ Do not install on a surface where it is exposed to direct sunlight, near heating equipment or heavy cold area. ~ Do not place this apparatus near conductive material. ~ Do not attempt to service this apparatus yourself.
CONTENTS OVERVIEW 6 7 8 8 Important Safety Instructions Recommended PC Specifications Recommended Micro SD/SDHC/SDXC Memory Card Specifications NAS recommended specs What’s Included Optional Accessories for Installation At a Glance INSTALLATION & CONNECTION 10 15 Installation Connecting with other Device NETWORK CONNECTION AND SETUP 19 Connecting the Camera Directly to Local Area Networking Connecting the Camera Directly to a DHCP Based DSL/Cable Modem Using Device Manager Automatically searching ca
overview RECOMMENDED PC SPECIFICATIONS NAS RECOMMENDED SPECS CPU : Intel(R) Core(TM) i7 3.4 GHz or higher RAM : 8G or higher Recommended browser: Chrome Supported browsers: Chrome, Safari, Firefox, MS Edge(chromium based) Supported OS : Windows, Mac, Linux, Android, iOS, Chrome Verification environment - Windows 10: Google Chrome version 80 or later, Firefox version 72 or later, MS Edge version 83 or later - Mac 10.13/14: Safari version 11.0.
WHAT’S INCLUDED Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.) Item Name Quantity Camera 1 Quick Guide (Optional) Description Appearance Item Name Quantity Description Cap Installer 1 Used to connect the RJ45 network cable Screw Cap 4 Used as a hole cap for Torx screw on the top cover Cable bushing 2 Extra cable bushing for network cable installation.
overview OPTIONAL ACCESSORIES FOR INSTALLATION AT A GLANCE You can purchase appropriate optional accessories available. Appearance a Model name Hanging Mount b All c SBP-300WMS (Wall Mount) XNF-9010RS SBP-300HMS6 SBP-300WMS1 (Wall Mount) SBP-300PMS (Pole Mount) SBP-300KMS (Corner Mount) Item 8_ overview Description a Mount plate Plate that fixes the camera when mounting it to the ceiling or attaching it to a separately sold mount.
Inside a Item bc ef Item a b g i j g Network Port Used to connect the PoE or Ethernet cable for network connection. h IR LED These infrared LED’s are controlled by the illumination sensor. i Fisheye lens This lens has 360˚ vision and it can record video panoramically. j Illumination Sensor Detects incoming light to control the IR LED. k Micro SD card slot Compartment for the Micro SD card.
installation & connection INSTALLATION J 2. Using the provided Torx L wrench, turn the 4 screws counterclockwise to release the top cover. ` Note that it is not necessary to loosen the screws completely. ` This camera is waterproof and in compliance with the IP66/IP67/IP6K9K spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Inserting a Micro SD card Removing a Micro SD card Slide the Micro SD card into the Micro SD card slot on the camera module in the direction of the arrow. Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD card from the slot. ! INSTALLATION & CONNECTION J ` Before installing the camera, the Micro SD card should be inserted while the power source and the body are separated. ` Do not forcefully insert it in the reverse direction.
installation & connection Installing the camera on the ceiling or a wall 3. Pass the audio/alarm/power cable and the network cable through the holes of the Mount Plate. 1. Attach the installation template on the desired surface and drill holes for screws and cables. 2. Fix the mount plate using appropriate screws. [Installing the network cable] 4. Pull off the extruded parts of the cable bushing to be used. 5. Use the cap installer to route the network cable through the cable bushing.
6. Mount the cable bushing to the camera body. 8. Join the mount plate with the camera body. TR20 [Installing the Audio/Alarm/Power cables] 9. Connect the network cable and alarm/power, audio jack to the camera module port. 7. Mount the cable bushing of the provided audio/alarm/power cables to the camera body.
installation & connection 10. Adjust the lens to the desired direction with reference to “Adjusting the monitoring direction for the camera” section. Adjusting the monitoring direction for the camera 11. Assemble the top cover. 4x TR20 ` Adjusting the monitoring direction You can adjust the camera direction only when the camera is fixed on the ceiling. Where, Turning the lens on its axis is called Rotation. - The effective range of rotation is a total of ±180 degrees.
CONNECTING WITH OTHER DEVICE Installation precautions when using the IR Manual mode ~ This mode is recommended when the luminance from each direction is different when monitoring under low luminance. ~ Since the position of the IR LED is fixed, if you rotate the camera lens, only the monitoring video of the camera will rotate but not the irradiation direction of the IR LED. ~ Make sure the factory default direction of the FRONT mark is placed right when installing it.
installation & connection Connecting WiFi Power Cable Specification Camera Setup 1. Connect OTG adapter (5-pin) and WiFi dongle to the micro USB port. Smartphone Setup 1. Install the Wisenet Installation application. 2. Select the camera SSID after turning on the WiFi. 4. When you log in to the camera, the video will be connected. ` The video will be played without being logged in during the initial connection. 5. You can adjust angle of view while watching the video through smartphone.
Connecting to Audio Input/Output Connecting to the I/O port box Connect the Alarm I/O cable to the corresponding port of the port box. Speaker PC ! INSTALLATION & CONNECTION Microphone Network Alarm (Warning lamp) Sensor hese ports can be used as alarm input or output ports. If used as input ports, ~ ALARM #1, ALARM #2 : T alarm input or day/night sensors can be connect to them. If used as output ports, alarm output signals can be connect to them.
installation & connection To connect the external sensor Connect one of the 2 signal lines to the [ALARM #1] port (if you want this to be the input port) and the remaining one to the [GND] port. Alarm In Wiring Diagram External connection Inside of the camera VCC_3.3V RESISTOR RESISTOR Sensor ALARM #1(5 mA SINK) RESISTOR MLCC DIODE TRANSISTOR GND GND To connect the alarm out If devices (e.g.
network connection and setup You can set up the network settings according to your network configurations. CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE MODEM INTERNET 1. Launch an Internet browser on the local PC. DSL/Cable Modem Camera 2. Enter the IP address of the camera in the address bar of the browser. External Remote PC DDNS Server (Data Center, KOREA) Camera 1. Connect the user PC directly with the network camera. 2.
network connection and setup USING DEVICE MANAGER M ` Device manager program can be downloaded from - menu at Hanwha Techwin website (http://www.hanwha-security.com). ` More instructions of Device Manager can be found at menu of the main page. AUTOMATICALLY SEARCHING CAMERA If using a Broadband Router ~ IP Address : Enter an address falling in the IP range provided by the Broadband Router. ex) 192.168.1.2~254, 192.168.0.2~254, 192.168.XXX.
Configuring Dynamic IP Receive IP address from DHCP ~ Example of the Dynamic IP environment - If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server AUTOMATICALLY CONFIGURING IP 1. Click the camera from the list that you want to automatically configure the IP. - If IPs are assigned by the internal DHCP server via the LAN 3. At the menu, click . 1. Click the camera from the list that you want to change the IP setting.
network connection and setup PORT RANGE FORWARD (PORT MAPPING) SETUP Setting up Port Range Forward for several network cameras If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the Broadband Router so that a remote PC can access the camera in it. ~ You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page. ~ A user can change each port using the camera setting screen.
CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 1. Run device manager. It will scan for connected cameras and display them as a list. M ! NETWORK CONNECTION AND SETUP 2. Double-click a camera to access. The Internet browser starts and connects to the camera. ` Access to the camera can also be gained by typing the camera’s IP address in the address bar of the Internet browser.
web viewer CONNECTING TO THE CAMERA Normally, you would 1. Launch the Internet browser. 2. Type the IP address of the camera in the address bar. ex) • IP address (IPv4) : 192.168.1.100 ; http://192.168.1.100 - the Login dialog should appear. • IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111 ; http://[2001:230:abcd:ffff:0000:0000:ffff:1111] - the Login dialog should appear. If the HTTP port is other than 80 1. Launch the Internet browser. 2.
PASSWORD SETTING When you access the product for the first time, you must register the login password. ` For a new password with 8 to 9 digits, you must use at least 3 of the following: uppercase/lowercase letters, numbers and special characters. For a password with 10 to 15 digits, you must use at least 2 types of those mentioned. - Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].?/ 1. Click the [Setup ( )] icon. 2. The Settings window appears. 3.
appendix TROUBLESHOOTING PROBLEM SOLUTION When an Windows 10 user accesses the web viewer through Chrome or Firefox, the sound volume of microphone changes periodically. ~ This is what happens when microphone driver has been set to Realtek driver. Install the High Definition Audio device (Windows Default Driver) or the third party driver as the microphone driver.
Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
