NETWORK CAMERA User Manual XNF-9010RV/XNF-9010RVM
Network Camera User Manual Copyright ©2020 Hanwha Techwin Co., Ltd. All rights reserved. Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
overview IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth. (Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.) 7.
overview Class construction An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection. Battery Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. The battery cannot be replaced. Disconnection Device Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location. When used outside of the U.S.
CONTENTS OVERVIEW 6 7 8 8 Important Safety Instructions Recommended PC Specifications Recommended Micro SD/SDHC/SDXC Memory Card Specifications NAS recommended specs What’s Included Optional Accessories for Installation At a Glance INSTALLATION & CONNECTION 10 15 Installation Connecting with other Device NETWORK CONNECTION AND SETUP 18 Connecting the Camera Directly to Local Area Networking Connecting the Camera Directly to a DHCP Based DSL/Cable Modem Using Device Manager Automatically searching c
overview RECOMMENDED PC SPECIFICATIONS NAS RECOMMENDED SPECS •• CPU : Intel(R) Core(TM) i7 3.4 GHz or higher •• RAM : 8G or higher •• Recommended browser: Chrome •• Supported browsers: Chrome, Safari, Firefox, MS Edge(chromium based) •• Supported OS : Windows, Mac, Linux, Android, iOS, Chrome •• Verification environment - Windows 10: Google Chrome version 80 or later, Firefox version 72 or later, MS Edge version 83 or later - Mac 10.13/14: Safari version 11.0.
WHAT’S INCLUDED Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.) MOUNTING HOLE (4X) HORIZONTAL LINE 160mm (6.30”) CABLE HOLE (2X) 27mm (1.06”) CABLE HOLE Description Item Name Quantity Description Model Name XNF-9010RV/ XNF-9010RVM Cable bushing 1 Extra cable bushing for network cable installation.
overview OPTIONAL ACCESSORIES FOR INSTALLATION AT A GLANCE You can purchase appropriate optional accessories available.
Inside a bc ef Item a b h g i k j Description g Network Port Used to connect the PoE or Ethernet cable for network connection. h IR LED These infrared LED’s are controlled by the illumination sensor. i Fisheye lens This lens has 360˚ vision and it can record video panoramically. j Illumination Sensor Detects incoming light to control the IR LED. k Micro SD card slot Compartment for the Micro SD card. l Microphone hole The MIC is built into the camera.
installation & connection INSTALLATION camera(XNF-9010RV/XNF-9010RVM) is waterproof and in compliance with the IP66 spec, but the jack connected to the JJ `` This external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being 2. Using the provided Torx L wrench, turn the 2 screws that secure the camera body counterclockwise to release the mount plate. `` You don’t have to completely remove the screws. externally exposed.
Removing a Micro SD card Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD card from the slot. Installing the camera on the ceiling or a wall 1. Attach the installation template on the desired surface and drill holes for screws and cables. ●● INSTALLATION & CONNECTION Before removing the Micro SD card, in
installation & connection [Installing the network cable] 4. Pull off the extruded parts of the cable bushing to be used. 5. Use the cap installer to route the network cable through the cable bushing. [Installing the Audio/Alarm/Power cables] 7. Mount the cable bushing of the provided audio/alarm/power cables to the camera body. Cap Installer 6. Mount the cable bushing to the camera body. 8. Join the mount plate with the camera body.
9. Connect the network cable and alarm/power, audio jack to the camera module port. 11. Assemble the top cover. 4x ●● INSTALLATION & CONNECTION x4 TR20 JJ `` When assembling the top cover, make the ‘FRONT’ mark on the camera body align with the logo on the cover. 10. Adjust the lens to the desired direction with reference to “Adjusting the monitoring direction for the camera” section. (page 14) `` If the cover is not fixed tightly, you may encounter a problem with waterproofing.
installation & connection Adjusting the monitoring direction for the camera Installation precautions when using the IR Manual mode •• This mode is recommended when the luminance from each direction is different when monitoring under low luminance. •• Since the position of the IR LED is fixed, if you rotate the camera lens, only the monitoring video of the camera will rotate but not the irradiation direction of the IR LED.
CONNECTING WITH OTHER DEVICE SOFT AP Connecting WiFi Camera Setup 1. Connect OTG adapter (5-pin) and WiFi dongle to the micro USB port. ●● INSTALLATION & CONNECTION Smartphone Setup 1. Install the Wisenet Installation application. 2. Select the camera SSID after turning on the WiFi. 3. Run the Wisenet Installation application. 4. When you log in to the camera, the video will be connected. `` The video will be played without being logged in during the initial connection. 5.
installation & connection Connecting a connector cable (XNF-9010RVM) Connect the M12 male connector into the hole of the M12 Female connector of the camera. Connecting to Audio Input/Output RX- TX+ Speaker MM `` This camera uses Female, D-coded types. `` PoE (Power over Ethernet) is supported. `` You are recommended to use a shielded network connector. JJ TX- `` Connect this camera to a shielded network cable (STP).
Connecting to the I/O port box To connect the external sensor Connect the Alarm I/O cable to the corresponding port of the port box. Connect one of the 2 signal lines to the [ALARM #1] port (if you want this to be the input port) and the remaining one to the [GND] port. External connection Inside of the camera VCC_3.
network connection and setup You can set up the network settings according to your network configurations. CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE MODEM Connecting to the camera from a local PC in the LAN INTERNET 1. Launch an Internet browser on the local PC. DSL/Cable Modem 2. Enter the IP address of the camera in the address bar of the browser. Camera External Remote PC DDNS Server (Data Center, KOREA) Camera 1.
USING DEVICE MANAGER MM `` Device manager program can be downloaded from - menu at Hanwha Techwin website (http://www.hanwha-security.com). AUTOMATICALLY SEARCHING CAMERA If a camera is connected to the same network of the PC where device manager is installed, you can find network camera by using search function. 1. Click at the main page of device manager. 2. Check the camera from the list. •• Check MAC address at the sticker attached to the camera.
network connection and setup Configuring Dynamic IP Receive IP address from DHCP •• Example of the Dynamic IP environment -- If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server -- If connecting the camera directly to modem using the DHCP protocols -- If IPs are assigned by the internal DHCP server via the LAN 1. Click the camera from the list that you want to change the IP setting. 2. Click at the main page of device manager. 3.
PORT RANGE FORWARD (PORT MAPPING) SETUP If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the Broadband Router so that a remote PC can access the camera in it. 1. From the Setup menu of the Broadband Router, select - . For setting the port range forward for a third-party Broadband Router, refer to the user guide of that Broadband Router. 2.
network connection and setup CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 1. Run device manager. It will scan for connected cameras and display them as a list. 2. Double-click a camera to access. The Internet browser starts and connects to the camera. MM `` Access to the camera can also be gained by typing the camera’s IP address in the address bar of the Internet browser.
web viewer CONNECTING TO THE CAMERA Normally, you would 2. Type the IP address of the camera in the address bar. ex) • IP address (IPv4) : 192.168.1.100 http://192.168.1.100 - the Login dialog should appear. • IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111 http://[2001:230:abcd:ffff:0000:0000:ffff:1111] - the Login dialog should appear. If the HTTP port is other than 80 1. Launch the Internet browser. 2. Type the IP address and HTTP port number of the camera in the address bar.
web viewer PASSWORD SETTING When you access the product for the first time, you must register the login password. `` For a new password with 8 to 9 digits, you must use at least 3 of the following: uppercase/lowercase letters, numbers and special characters. For a password with 10 to 15 digits, you must use at least 2 types of those mentioned. -- Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].
appendix TROUBLESHOOTING PROBLEM What are the specifications for WAVE files necessary to play audio at the time of an event? No video is displayed when accessing the plug-in free webviewer on Safari via HTTPS. yy This is what happens when microphone driver has been set to Realtek driver. Install the High Definition Audio device (Windows Default Driver) or the third party driver as the microphone driver. yy Sampling rate of 48,000 KHz or less is recommended.
Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
