NETWORK CAMERA User Manual XNP-9250R/XNP-9250 XNP-8250R/XNP-8250 XNP-6400R/XNP-6400
Network Camera User Manual Copyright ©2020 Hanwha Techwin Co., Ltd. All rights reserved. Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
overview IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth. (Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.) 7.
overview Class construction Please read the following recommended safety precautions carefully. An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection. ~~ Do not place this apparatus on an uneven surface. ~~ Do not install on a surface where it is exposed to direct sunlight, near heating equipment or heavy cold area. ~~ Do not place this apparatus near conductive material. ~~ Do not attempt to service this apparatus yourself.
CONTENTS OVERVIEW INSTALLATION & CONNECTION 10 17 Installation Powering and networking NETWORK CONNECTION AND SETUP 19 Connecting the Camera Directly to Local Area Networking Connecting the Camera Directly to a DHCP Based DSL/Cable Modem Using Device Manager Automatically searching camera Configuring IP address Manually registering camera Automatically configuring IP Port Range Forward (Port Mapping) Setup Connecting to the Camera from a Shared Local PC Connecting to the Camera from a Remote PC via th
overview RECOMMENDED PC SPECIFICATIONS NAS RECOMMENDED SPECS ~~ ~~ ~~ ~~ ~~ ~~ ~~ Recommended capacity : 200GB or higher is recommended. ~~ For this camera, you are recommended to use a NAS with the following manufacturer’s specs. Recommended products : QNAP NAS, Synology NAS CPU : Intel(R) Core(TM) i7 3.4 GHz or higher RAM : 8G or higher Supported OS : MS Windows 8.1, 10, Mac OS X 10.
WHAT’S INCLUDED NETWORK I/O BOX - SEPARATELY SOLD PRODUCT Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.) Item Name Main Body Quantity Description Item Name Description Model Name Network I/O box External connection device for camera’s alarm and audio I/O SPM-4210 Model Name !! OVERVIEW Appearance Appearance 1 of the Be ware CAUTION: and Polarity Rated Voltageconnection.
overview AT A GLANCE Inside(XNP-9250R/XNP-8250R/XNP-6400R) e Appearance a c b Item a b c d Description a Main cover Protects the internal PTZ mechanism from the direct sunlight, rain or external impact. b Dome cover Shield cover for the lens and unit protection. c Micro SD Card cover Covers micro SD card slots and the Reset button. You can open it using the Torx L wrench. f Item Description a IR LED These infrared LED’s are controlled by the illumination sensor.
Inside(XNP-9250/XNP-8250/XNP-6400) Mounting surface !! OVERVIEW a b c c d a b Item Item Description a Lens Lens for the camera. b Heater At a certain temperature below the threshold, it automatically operates, or you can turn it on manually in the web viewer. Description a Cable bushing A waterproof rubber cap, which allows a network cable to go through it. b Safety wire hook Hang this hook on the safety wire of the mount when installing this product to prevent it from falling.
installation & connection INSTALLATION 2. Push in a flathead screwdriver under the slot to pull out the Micro SD card slot. camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are JJ `` This recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Removing a Micro SD card Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD card from the slot. !! OVERVIEW 4. After inserting the Micro SD cards, push the Micro SD card slot until it clicks into place. 5. Fix the Micro SD card slot using screws. JJ `` Tighten the screws when assembling the Micro SD card cover to prevent moisture penetration.
overview Getting ready for network cable installation 4. For waterproof protection, pull down the cable below the cable bushing as shown in the figure below. 1. Remove the cable bushing. 9~10 cm Installing using wall & pole mount the power only after installation is complete. Supplying power while the installation is in progress may cause fire or JJ `` Connect damage the product. 2. Pull off the extruded part of the removed cable bushing. 3.
2. Connect the network cable to the network port. 4. Install the bushing clip. Let the arrow mark on the clip point in the direction of the safety wire hook, and click each side into place one at a time. !! INSTALLATION & CONNECTION 3. Plug the cable bushing of the network cable in the hole. When plugging it in, press the whole bushing area evenly so that it is properly plugged in. 5.
installation & connection 6. Tightly fasten the 3 mounting screws on the inside of the Wall & Pole Mount. Installing using ceiling or parapet mount 1. Hang the safety wire of the mount on the safety wire hook of the product. TR30 Safety wire Safety wire hook 7. Join the top cover of the wall & pole mount. 2. Connect the network cable to the network port.
3. Plug the cable bushing of the network cable in the hole. When plugging it in, press the whole bushing area evenly so that it is properly plugged in. 5. After aligning the installation direction guides of the hanging mount, push the main cover upward and turn it counterclockwise until it is secured. !! INSTALLATION & CONNECTION JJ `` The length and width of the cable bushing are different. Check the shape and plug it in the right direction. 6.
installation & connection `` Joined with official product mounts (ceiling/parapet) Ceiling Mount (SBP-300CMW) Hanging Mount (SBP-156HMW) Ceiling Mount (SBP-156CMW) Parapet Mount (SBP-156LMW) `` Joined with mounts other than official product mounts If you use hanging mount, you can install the camera onto any mount other than the official product mount.
POWERING AND NETWORKING To use XNP-9250R/XNP-8250R/XNP-6400R models, connect the HPoE injector shipped together. To use XNP-9250/XNP-8250/XNP-6400 models, connect a PoE+-supported router or PoE+ injector. Item Connector Ethernet Cable Max Distance PoE Support Switch SFP Port Switch Contents RJ45 (10/100BASE-T) 10/100BASE-T UTP Category 5e 100 m HPoE (XNP-9250R/XNP-8250R/XNP-6400R) PoE+ (XNP-9250/XNP-8250/XNP-6400) Remark DC Resistance ≤ 0.
installation & connection Connecting audio and alarm I/O You can connect audio and alarm using a network I/O box separately sold. Microphone Network Speaker Sensor Alarm (Warning lamp) more information on the network I/O box, see the manual for the network I/O box. MM ```` For You can set the network I/O box in Camera web viewer ; ; menu. `` Connect only one camera per network I/O box. The product may malfunction if more than one camera is connected.
network connection and setup You can set up the network settings according to your network configurations. CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE MODEM INTERNET 1. Launch an Internet browser on the local PC. DSL/Cable Modem 2. Enter the IP address of the camera in the address bar of the browser. External Remote PC Camera DDNS Server (Data Center, KOREA) Camera 1. Connect the user PC directly with the network camera.
network connection and setup USING DEVICE MANAGER manager program can be downloaded from - menu at Hanwha Techwin website MM `` Device (http://www.hanwha-security.com). `` More instructions of Device Manager can be found at menu of the main page. AUTOMATICALLY SEARCHING CAMERA If using a Broadband Router ~~ IP Address : Enter an address falling in the IP range provided by the Broadband Router. ex) 192.168.1.2~254, 192.168.0.2~254, 192.168.XXX.
Configuring Dynamic IP Receive IP address from DHCP ~~ Example of the Dynamic IP environment -- If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server AUTOMATICALLY CONFIGURING IP 1. Click the camera from the list that you want to automatically configure the IP. -- If IPs are assigned by the internal DHCP server via the LAN 3. At the menu, click . 1. Click the camera from the list that you want to change the IP setting.
network connection and setup PORT RANGE FORWARD (PORT MAPPING) SETUP Setting up Port Range Forward for several network cameras If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the Broadband Router so that a remote PC can access the camera in it. ~~ You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page. ~~ A user can change each port using the camera setting screen. Manual Port Range Forwarding 1.
CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 1. Run device manager. It will scan for connected cameras and display them as a list. !! NETWORK CONNECTION AND SETUP 2. Double-click a camera to access. The Internet browser starts and connects to the camera. MM `` Access to the camera can also be gained by typing the camera’s IP address in the address bar of the Internet browser.
web viewer CONNECTING TO THE CAMERA Normally, you would 1. Launch the Internet browser. 2. Type the IP address of the camera in the address bar. ex) ~ IP address (IPv4) : 192.168.1.100 ; http://192.168.1.100 - the Login dialog should appear. ~ IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111 ; http://[2001:230:abcd:ffff:0000:0000:ffff:1111] - the Login dialog should appear. If the HTTP port is other than 80 1. Launch the Internet browser. 2.
PASSWORD SETTING When you access the product for the first time, you must register the login password. characters. For a password with 10 to 15 digits, you must use at least 2 types of those mentioned. -- Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].?/ 1. Click the [Setup ( )] icon. 2. The Settings window appears. 3. You can configure settings for the camera’s basic information, video, audio, network, event, analysis, and system over the network. 4.
appendix TROUBLESHOOTING PROBLEM No video is displayed when accessing the plug-in free webviewer on Safari via HTTPS. SOLUTION PROBLEM ~~ On the authentication popup window prompted when initially accessing https, click "View Authentication Certificate" and select the "Always trust when connecting to the designated webviewer IP" check box. of is set to , but no notification e-mail reaches me even when an analysis event had occurred.
Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
