NETWORK CAMERA User Manual XNP-9300RW XNP-8300RW XNP-6400RW
Network Camera User Manual Copyright ©2020 Hanwha Techwin Co., Ltd. All rights reserved. Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
overview IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth. (Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.) 7.
overview Class construction An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection. Battery Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. The battery cannot be replaced. Disconnection Device Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location. When used outside of the U.S.
CONTENTS OVERVIEW 6 7 7 8 Important Safety Instructions Recommended PC Specifications Recommended Micro SD/SDHC/SDXC Memory Card Specifications NAS recommended specs What’s Included Optional Accessories for Installation At a Glance INSTALLATION & CONNECTION 10 17 Installation Powering and networking NETWORK CONNECTION AND SETUP 18 Connecting the Camera Directly to Local Area Networking Connecting the Camera Directly to a DHCP Based DSL/Cable Modem Using Device Manager Automatically searching camera
overview RECOMMENDED PC SPECIFICATIONS NAS RECOMMENDED SPECS •• CPU : Intel(R) Core(TM) i7 3.4 GHz or higher •• RAM : 8G or higher •• Supported OS : MS Windows 8.1, 10, Mac OS X 10.13 •• Recommended browser: Google Chrome •• Supported browsers: MS Explore11, MS Edge, Mozilla Firefox (Window 64bit only), Apple Safari (Mac OSX only) •• VGA : PCIe 256MB GDDR3 video graphics card or higher •• Recommended capacity : 200GB or higher is recommended.
WHAT’S INCLUDED OPTIONAL ACCESSORIES FOR INSTALLATION Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.) SFP LAN PoE 0Link Quantity Description Main Body 1 Quick Guide (Optional) 1 HPoE injector 1 Power cord 1 Connects to HPoE injector Cap Installer 1 Used to connect the network cable Bushing clip 1 Used as a means of preventing cable bushing from being separated or falling apart from the hole.
overview AT A GLANCE Appearance Inside a d a b d c e b c Item Description a Main cover b Windshield wiper c Shield cover Shield cover for the lens and unit protection. d Micro SD Card cover Covers micro SD card slots and the Reset button. You can open it using a Torx driver. 8_ overview Item Description Protects the internal PTZ mechanism from the direct sunlight, rain or external impact. a IR LED These infrared LED’s are controlled by the illumination sensor.
Mounting surface a ●● OVERVIEW b c Item Description a Cable bushing A waterproof rubber cap, which allows a network cable to go through it. b Safety wire hook Hang this hook on the safety wire of the mount when installing this product to prevent it from falling. c HPoE port A port that connects to the HPoE injector and network cable for power and network connection.
installation & connection INSTALLATION 2. Pull up the Micro SD card cover and push the Micro SD card to the arrow direction as shown in the figure. camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are JJ `` This recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Removing a Micro SD card Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD card from the slot. Getting ready for network cable installation 1. Remove the cable bushing. ●● OVERVIEW removing the Micro SD card, in , set the device to and press the [Apply] button and turn the JJ `` Before camera off. `` If you turn off the camera or remove the Micro SD card that contains data from the product, the data may be lost or damaged. 2.
installation & connection 4. For waterproof protection, pull down the cable below the cable bushing as shown in the figure below. 2. Connect the network cable to the HPoE port. 9~10 cm Installing using wall & pole mount on the HPoE injector only after installation is complete. Supplying power while the installation is in progress may cause JJ `` Power fire or damage the product. 3. Plug the cable bushing of the network cable in the hole.
4. Install the bushing clip. Let the arrow mark on the clip point in the direction of the safety wire hook, and click each side into place one at a time. 6. Tightly fasten the 3 mounting screws on the inside of the Wall & Pole Mount. ●● INSTALLATION & CONNECTION TR30 5. After aligning the installation direction guides of the camera and wall & pole mount, push the main cover upward and turn it counterclockwise until it is secured. 7. Join the top cover of the wall & pole mount.
installation & connection Installing with hanging mount If you use hanging mount, you can install the camera onto any mount other than the official product mount. 3. Connect the network cable to the HPoE port. 1. Install the hanging mount by turning it counterclockwise into the installed mount. 4. Plug the cable bushing of the network cable in the hole. When plugging it in, press the whole bushing area evenly so that it is properly plugged in. 2.
5. Install the bushing clip. Let the arrow mark on the clip point in the direction of the safety wire hook, and click each side into place one at a time. 7. Tightly fasten the 3 mounting screws on the top side of the Hanging Mount. ●● INSTALLATION & CONNECTION TR30 6. After aligning the installation direction guides of the hanging mount, push the main cover upward and turn it counterclockwise until it is secured.
installation & connection Replacing the rubber of wiper blade If the rubber part of your wiper blade is worn and not cleaning the window properly, you can replace the rubber part. 3. Remove the rubber part by pulling it back. 1. Lift up the wiper. 4. Insert the rubber replacement in the joint groove by sliding it in the direction of the arrow. 2. Pull the wiper blade back. 5. Turn the wiper blade back to its original position and put it down slowly.
POWERING AND NETWORKING SFP port Specification Support SFP Voltage Connect the HPoE injector with the HPoE port of the camera. Standard mini-SFP Cage(for 6.5 mm pitch SFP) Required SFP Speed 1250 Mbps(For 1000 Mbps Ethernet) Transmission Method(Optical) Mode Depends on SFP Module Cable Insertion Loss(dB) Mode Depends on SFP Module SFP LAN PoE Optical Mode(Long/Short Wave) 0Link LC Type ●● INSTALLATION & CONNECTION Required SFP’s BER(Bit Error Rate) SFP Port Switch 3.
network connection and setup You can set up the network settings according to your network configurations. CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE MODEM Connecting to the camera from a local PC in the LAN INTERNET 1. Launch an Internet browser on the local PC. DSL/Cable Modem 2. Enter the IP address of the camera in the address bar of the browser. External Remote PC Camera DDNS Server (Data Center, KOREA) Camera 1.
USING DEVICE MANAGER MM `` Device manager program can be downloaded from - menu at Hanwha Techwin website (http://www.hanwha-security.com). AUTOMATICALLY SEARCHING CAMERA If a camera is connected to the same network of the PC where device manager is installed, you can find network camera by using search function. 1. Click at the main page of device manager. 2. Check the camera from the list. •• Check MAC address at the sticker attached to the camera.
network connection and setup Configuring Dynamic IP Receive IP address from DHCP •• Example of the Dynamic IP environment -- If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server -- If connecting the camera directly to modem using the DHCP protocols -- If IPs are assigned by the internal DHCP server via the LAN 1. Click the camera from the list that you want to change the IP setting. 2. Click at the main page of device manager. 3.
PORT RANGE FORWARD (PORT MAPPING) SETUP If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the Broadband Router so that a remote PC can access the camera in it. 1. From the Setup menu of the Broadband Router, select - . For setting the port range forward for a third-party Broadband Router, refer to the user guide of that Broadband Router. 2.
network connection and setup CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 1. Run device manager. It will scan for connected cameras and display them as a list. 2. Double-click a camera to access. The Internet browser starts and connects to the camera. MM `` Access to the camera can also be gained by typing the camera’s IP address in the address bar of the Internet browser.
web viewer CONNECTING TO THE CAMERA Normally, you would 2. Type the IP address of the camera in the address bar. ex) • IP address (IPv4) : 192.168.1.100 http://192.168.1.100 - the Login dialog should appear. • IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111 http://[2001:230:abcd:ffff:0000:0000:ffff:1111] - the Login dialog should appear. If the HTTP port is other than 80 1. Launch the Internet browser. 2. Type the IP address and HTTP port number of the camera in the address bar.
web viewer PASSWORD SETTING When you access the product for the first time, you must register the login password. a new password with 8 to 9 digits, you must use at least 3 of JJ `` For the following: uppercase/lowercase letters, numbers and special characters. For a password with 10 to 15 digits, you must use at least 2 types of those mentioned. -- Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].
appendix TROUBLESHOOTING PROBLEM yy On the authentication popup window prompted when initially accessing https, click "View Authentication Certificate" and select the "Always trust when connecting to the designated webviewer IP" check box. yy If the webviewer continues failing to display a video after you select "Next" on the message window below, press the command key + Q to exit the Safari browser, access again and follow the procedures stated above.
Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
