NETWORK CAMERA User Manual XNV-6081/XNV-6081R/XNV-8081R XND-6081V/XND-6081RV/XND-8081RV XND-6081F/XND-6081RF/XND-8081RF
Network Camera User Manual Copyright ©2019 Hanwha Techwin Co., Ltd. All rights reserved. Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
overview Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth. (Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.) 7.
overview Class construction An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection. Battery Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. The battery cannot be replaced. Disconnection Device Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location. When used outside of the U.S.
CONTENTS overview outdoor vandal dome 8 indoor vandal dome 17 6 Important Safety Instructions Recommended PC Specifications Recommended Micro SD/SDHC/SDXC Memory Card Specifications NAS recommended specs 8 8 9 What’s Included At a Glance Installation 17 17 18 What’s Included At a Glance Installation flush mount dome 25 25 26 What’s Included At a Glance Installation installation & connection 32 34 Optional Accessories for Installation Connecting with other Device 25 32 38 38 38 39 39 41 4
overview Recommended PC Specifications NAS recommended specs •• CPU : Intel(R) Core(TM) i7 3.4 GHz or higher •• RAM : 8G or higher •• Supported OS : MS Windows, Mac OS X •• Recommended browser: Google Chrome Supported browsers: MS Explorer, MS Edge, Mozilla Firefox (Window 64bit only), Apple Safari (Mac OSX only) •• Recommended capacity : 200GB or higher is recommended. •• Simultaneous access : One unit of NAS can accept a maximum of sixteen camera accesses.
XNV-6081/XNV-6081R/XNV-8081R 8 Indoor Vandal Dome XND-6081V/XND-6081RV/XND-8081RV 17 Flush Mount Dome XND-6081F/XND-6081RF/XND-8081RF 25 English _7 ●● overview Outdoor Vandal Dome
What’s Included As for each sales country, accessories are not the same. of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection.
Installation 2. Take off the cushion protecting the camera lens. camera is waterproof and in compliance with the IP67 / IP66 spec, but the jack connected to the external cable is not. JJ `` This You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
outdoor vandal dome Removing a Micro SD Memory Card Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot. Installing the AC module (sold separately: SPC-100AC) 1. Install the AC module as shown in the figure. 2. Tighten the screw using the hex key. 1x JJ `` Please note that if you firmly push and release the Micro SD memory card when it is ejected, it may pop out.
Installation (mount plate) [Directly installing on wall/ceiling] [Installing using pipe] 2-1. Attach the installation template and drill holes for screws and cables. 1-1. Attach the installation template on the desired surface and drill holes for screws and cables. ●● Outdoor Vandal Dome 2-2. Separate the pipe cover of the mount plate by pressing its sides. 1-2. Fix the mount plate using appropriate screws. 1-3.
outdoor vandal dome 2-3. Place the pipe on the mount plate. 2-4. Fix the mount plate using appropriate screws. 1-4. Mount the bush to the camera case. 2-5. Pull out necessary cables among LAN/power/audio & alarm cables through the pipe. Installation (camera case) JJ `` Use a cable bush compliant with the LAN cable to be connected. -- Camera main: use a cable with the diameter of Ø5 to 6.5 -- Components: use a cable with the diameter of Ø5 to 8.5 [Installing LAN/power cables] 1-1.
2-3. Mount the bush to the camera case. 4. Join the mount plate with the camera case. ●● Outdoor Vandal Dome 2x x4 TR20 [Installing audio & alarm cables] 3-1. Mount the bush of the provided audio & alarm cables to the camera case.
outdoor vandal dome Installing the camera module 1. Connect the LAN/power/audio & alarm cables to the camera module terminal. 2. Attach the camera module to the case. JJ `` A magnet is embedded at the bottom of the module `` Take caution not to allow any foreign objects between the attaching surfaces. Assembling the dome cover [Directly installing on wall/ceiling] 1. Assemble the dome cover. JJ `` Make sure to firmly tighten the fastening screws so that there is no water damage issue.
Using/Removing Skin cover [Using Weather cap] 1. Remove the screws from the dome cover. 1. Put on the skin cover in alignment with the pipe cover. ●● Outdoor Vandal Dome 2x TR20 2. Assemble the dome cover. 3. Mount the weather cap to the dome cover and fasten the screws. JJ `` Make sure to firmly tighten the fastening screws so that there is no water damage issue. 2. For a camera connected with a pipe, remove the pipe cover from the skin cover first before putting it on.
outdoor vandal dome 3. To remove the skin cover, pull it while turning it clockwise as shown in the figure. JJ `` Repetitive installation and removal of the skin cover may deform the skin cover. `` Installation and removal of the skin cover with excessive force may cause scratches on the surface of the product.
What’s Included ●● Indoor Vandal Dome of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection.
indoor vandal dome Installation 2. Take off the cushion protecting the camera lens. camera is waterproof and in compliance with the IP52 spec, but the jack connected to the external cable is not. You are JJ `` This recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Removing a Micro SD Memory Card Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot. Installation (mount plate) [Directly installing on wall/ceiling] 1-1. Attach the installation template on the desired surface and drill holes for screws and cables. ●● Indoor Vandal Dome JJ `` Please note that if you firmly push and release the Micro SD memory card when it is ejected, it may pop out.
indoor vandal dome [Installing using pipe] 2-1. Attach the installation template and drill holes for screws and cables. 2-2. Separate the pipe cover of the mount plate by pressing its sides. 2-3. Place the pipe on the mount plate. 2-4. Fix the mount plate using appropriate screws. 2-5. Pull out necessary cables among LAN/power/audio & alarm cables through the pipe. Installation (camera case) JJ `` Use a cable bush compliant with the LAN cable to be connected.
1-4. Mount the bush to the camera case. 2-3. Mount the bush to the camera case. ●● Indoor Vandal Dome [Installing the LAN cable] 2-1. Pull off the extruded part of the 1-hole bush provided. 2-2. Use the cap installer to pass through the RJ45 cable.
indoor vandal dome Installing the camera module [Installing audio & alarm cables] 3-1. Mount the bush of the provided audio & alarm cables to the camera case. 1. Connect the LAN/power/audio & alarm cables to the camera module terminal. 2. Attach the camera module to the case. JJ `` A magnet is embedded at the bottom of the module `` Take caution not to allow any foreign objects between the attaching surfaces. 3. Connect the microphone cable to the camera module. 4.
Assembling the dome cover Using/Removing Skin cover 1. Put on the skin cover in alignment with the pipe cover. [Directly installing on wall/ceiling] 1. Assemble the dome cover. ●● Indoor Vandal Dome JJ `` Make sure to firmly tighten the fastening screws so that there is no water damage issue. 4x x4 TR20 2. For a camera connected with a pipe, remove the pipe cover from the skin cover first before putting it on. JJ `` Be careful not to alter the monitoring direction of your camera.
indoor vandal dome 3. To remove the skin cover, pull it while turning it clockwise as shown in the figure. JJ `` Repetitive installation and removal of the skin cover may deform the skin cover. `` Installation and removal of the skin cover with excessive force may cause scratches on the surface of the product.
At a Glance flush mount dome What’s Included a Bracket As for each sales country, accessories are not the same. of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection.
flush mount dome Installation 2. Take off the cushion protecting the camera lens. camera is waterproof and in compliance with the IP52 spec, but the jack connected to the external cable is not. You are JJ `` This recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Removing a Micro SD Memory Card Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot. Installation (housing) 1. Attach the installation template to the ceiling and mark its location with a pencil. ●● Flush Mount Dome JJ `` Please note that if you firmly push and release the Micro SD memory card when it is ejected, it may pop out.
flush mount dome 3. Connect the safety cable. JJ `` A safety cable is not provided. e.g. [Using pipe] 4-1. Install the pipe in a fitting hole. ¾” NUT ½” NUT 28_ flush mount dome 4-2. Pull out necessary cables among LAN/power/audio & alarm cables through the pipe.
Installation (camera case) JJ `` Use a cable bush compliant with the LAN cable to be connected. -- Components: use a cable with the diameter of Ø5 to 8.5 2-1. Pull off the extruded part of the 1-hole bush provided. 2-2. Use the cap installer to pass through the RJ45 cable. Cap Installer ●● Flush Mount Dome [Installing LAN/power cables] [Installing the LAN cable] 1-1. Pull off the extruded parts of the bush to be used. 1-2.
flush mount dome [Installing audio & alarm cables] 3-1. Mount the bush of the provided audio & alarm cables to the camera case. Installing the camera module 1. Connect the LAN/power/audio & alarm cables to the camera module terminal. 2. Attach the camera module to the case. JJ `` A magnet is embedded at the bottom of the module `` Take caution not to allow any foreign objects between the attaching surfaces. 4. Turn the screws on the housing to fix the housing to the ceiling.
Assembling the dome cover Outdoor installation JJ `` Make sure to firmly tighten the fastening screws so that there is no water damage issue. 1. Connect the power, I/O, and LAN cables. 1. Assemble the dome cover. 2. Wrap the black cable jacket (Area A) and the cable connection area with waterproof (butyl rubber) tape so that more than half of the butyl rubber tape is overlapped.
of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power installation & connection Optional Accessories for Installation You can purchase appropriate optional accessories available.
Adjusting the monitoring direction for the camera JJ `` Adjust the direction of IR LEDs not to hinder their view by an instrument. JJ `` Adjust the direction of IR LEDs not to hinder their view by a weather cap (if any). ●● installation & connection Tilt Pan Lens rotation `` Adjusting the monitoring direction You can adjust the camera direction only when the camera is fixed on the ceiling.
installation & connection Connecting with other Device Ethernet Connection Connect the Ethernet cable to the local network or to the Internet. WiFi dongle SOFT AP Connecting WiFi Camera Setup 1. Connect OTG adapter (5-pin) and WiFi dongle to the micro USB terminal. Smartphone Setup 1. Install the Wisenet Installation application. 2. Select the camera SSID after turning on the WiFi. 3. Run the Wisenet Installation application. * AC 4. When you log in to the camera, the video will be connected.
Power Supply Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the camera. PC Speaker `` If the power sources for PoE and DC 12 V are simultaneously turned on, the device power will be supplied by both of PoE and DC 12 V. ●● installation & connection JJ Connecting to Audio Input/Output Microphone -- You can also use a router featuring PoE to supply power to the camera. -- Use PoE that is compliant with the IEEE 802.3af protocols.
installation & connection •• Audio Codec -- Audio In : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz), G.726 ADPCM (Bit Rate: 16Kbps, 24Kbps, 32Kbps, 40Kbps / Sampling Frequency: 8kHz), AAC (Bit Rate: 48Kbps / Sampling Frequency: 16kHz) Connecting to the I/O port box Connect the Alarm I/O cable to the corresponding port of the port box. -- Audio Out : G.
Alarm In Wiring Diagram External connection Inside of the camera VCC_3.3V ALARM IN (5mA SINK) RESISTOR RESISTOR MLCC GND ●● installation & connection RESISTOR Sensor DIODE TRANSISTOR GND Alarm Out Wiring Diagram Warning lamp / Siren power (-) External connection Inside of the camera DC 5V or 3.
network connection and setup You can set up the network settings according to your network configurations. Connecting the Camera Directly to Local Area Networking Connecting the Camera Directly to a DHCP Based DSL/Cable Modem Connecting to the camera from a local PC in the LAN INTERNET 1. Launch an Internet browser on the local PC. DSL/Cable Modem 2. Enter the IP address of the camera in the address bar of the browser. External Remote PC Camera DDNS Server (Data Center, KOREA) Camera 1.
Buttons used in IP Installer a b c d Item e f g Description Scans for cameras with the IPv6 setting. Activated in an IPv6 compliant environment only. IPv6 j Search Scans for cameras that are currently connected to the network. However, this button will be grayed out if neither IPv4 nor IPv6 is checked. k l m Auto Set The IP Installer automatically configures the network settings. Manual Set You should configure the network settings manually. Exit Exits the IP Installer program.
network connection and setup If not using a Broadband Router If the Broadband Router has more than one camera connected 4. In the pane, provide necessary information. •• HTTP Port : Used to access the camera using the Internet browser, defaulted to 80. •• VNP Port : Used to control the video signal transfer, defaulted to 4520. ex) For setting , , and , contact your network administrator. 5. Enter the password.
Dynamic IP Setup Dynamic IP Environment Setup MM `` Above sample instructions are based on the CISCO’s Broadband Router. `` The settings may differ depending on the connected Broadband Router model. For more information, refer to the user manual of the applicable router. -- If connecting the camera directly to modem using the DHCP protocols -- If IPs are assigned by the internal DHCP server via the LAN Checking the Dynamic IP 1. Run the IP Installer on the user’s local computer.
network connection and setup Connecting to the Camera from a Shared Local PC 1. Run the IP Installer. It will scan for connected cameras and display them as a list. 2. Double-click a camera to access. The Internet browser starts and connects to the camera. to the camera can also be gained by typing the camera’s IP MM `` Access address in the address bar of the Internet browser.
web viewer Connecting to the Camera Normally, you would 2. Type the IP address of the camera in the address bar. ex) • IP address (IPv4) : 192.168.1.100 http://192.168.1.100 - the Login dialog should appear. • IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111 http://[2001:230:abcd:ffff:0000:0000:ffff:1111] - the Login dialog should appear. If the HTTP port is other than 80 1. Launch the Internet browser. 2. Type the IP address and HTTP port number of the camera in the address bar.
web viewer Password setting When you access the product for the first time, you must register the login password. When the “Password change” window appears, enter the new password. a new password with 8 to 9 digits, you must use at least 3 of JJ `` For the following: uppercase/lowercase letters, numbers and special characters. For a password with 10 to 15 digits, you must use at least 2 types of those mentioned. -- Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].
appendix Specification Items NETD None Pixel Size Min. Illumination Video Out Focal Length (Zoom Ratio) Max. Aperture Ratio Angular Field of View Lens Min. Object Distance Focus Control Lens Type Mount Type Optional Lens Description XND-6081V/XND-6081RV XND-6081F/XND-6081RF None XNV-6081/XND-6081V/XND-6081F - Color : 0.015 Lux(F1.4, 1/30sec), B/W : 0.0015 Lux(F1.4, 1/30sec) IR Viewable Length F1.4(Wide) ~ F3.6(Tele) Camera Title H : 119.5°(Wide) ~ 27.9°(Tele) Day & Night V : 62.
appendix Items Privacy Masking Gain Control Low / Middle / High LDC Electronic Shutter Speed Items XND-6081V/XND-6081RV XND-6081F/XND-6081RF 32ea, polygonal zones - Color : Gray, Green, Red, Blue, Black, White - Mosaic White Balance Operational XNV-6081/XNV-6081R Description Audio out Operational XND-6081V/XND-6081RV XND-6081F/XND-6081RF Line out, Max output level: 1 Vrms None Coaxial Protocol None Temperature detect range None Video Transmission Distance None ATW / AWC / Manual / Indoor
Items Items XND-6081V/XND-6081RV XND-6081F/XND-6081RF IPv4, IPv6, TCP/IP, UDP/IP, RTP(UDP), RTP(TCP), RTCP, RTSP, NTP, HTTP, HTTPS, SSL/TLS, DHCP, FTP, SMTP, ICMP, IGMP, SNMPv1/v2c/v3(MIB-2), ARP, DNS, DDNS, QoS, PIM-SM, UPnP, Bonjour, LLDP Input Voltage Network Edge Storage Application Programming Interface Digest Login Authentication Electrical IP Address Filtering User access Log 802.
appendix Items 1/1.8” 6MP CMOS NETD None Effective Pixels Video Pixel Size Min. Illumination Video Out Focal Length (Zoom Ratio) Max. Aperture Ratio Angular Field of View Lens XNV-8081R Imaging Device Min. Object Distance Focus Control Lens Type Mount Type Optional Lens Description XND-8081RV Items XND-8081RF B/W : 0 Lux(IR LED on) Pan / Tilt / Rotate CVBS: 1.0 Vp-p / 75Ω composite, 720x480(N), 720x576(P) for installation Auto Tracking H : 92.1°(Wide) ~ 38.
Items XND-8081RV Gain Control Low / Middle / High LDC Electronic Shutter Speed XND-8081RF Support Minimum / Maximum / Anti flicker (2 ~ 1/12,000sec) Radiometry Analytics Defocus detection, Directional detection, Fog detection, Face detection, Motion detection, Digital auto tracking, Appear/Disappear, Enter/Exit, Loitering, Tampering, Virtual line, Audio detection, Sound classification, Shock detection Business Intelligence People counting, Queue management, Heatmap Alarm Triggers Input 1ea / O
appendix Items Protocol Description XND-8081RV XNV-8081R XND-8081RF IPv4, IPv6, TCP/IP, UDP/IP, RTP(UDP), RTP(TCP), RTCP, RTSP, NTP, HTTP, HTTPS, SSL/TLS, DHCP, FTP, SMTP, ICMP, IGMP, SNMPv1/v2c/v3(MIB-2), ARP, DNS, DDNS, QoS, PIM-SM, UPnP, Bonjour, LLDP Network Edge Storage Application Programming Interface Digest Login Authentication IP Address Filtering User access Log 802.
Product Overview XNV-6081/XNV-6081R/XNV-8081R XND-6081V/XND-6081RV/XND-8081RV Unit : mm (inch) Unit : mm (inch) ●● appendix English _51
appendix XND-6081F/XND-6081RF/XND-8081RF Unit : mm (inch) Troubleshooting PROBLEM When an Windows 10 user accesses the web viewer through Chrome or Firefox, the sound volume of microphone changes periodically. What are the specifications for WAVE files necessary to play audio at the time of an event? No video is displayed when accessing the plug-in free webviewer on Safari via HTTPS. SOLUTION yy This is what happens when microphone driver has been set to Realtek driver.
PROBLEM SOLUTION Voice is not recorded even though audio input settings are configured. yy You must enable the
Open Source Announcement GPL/LGPL software license If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source distribution might be charged. Component Name License Base Kernel Busybox iproute2-4.3.0 iptables-1.4.21 ethtool-4.2 mtd-1.5.2 mii-diag-2.11 rp-pppoe-3.11 wpa_supplicant-2.5 bash-4.3.30 zeroconf GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 3.0 GPL 2.
components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 4.
2. Basic Permissions. All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions are met. This License explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is covered by this License only if the output, given its content, constitutes a covered work. This License acknowledges your rights of fair use or other equivalent, as provided by copyright law.
patent license to some of the parties receiving the covered work authorizing them to use, propagate, modify or convey a specific copy of the covered work, then the patent license you grant is automatically extended to all recipients of the covered work and works based on it.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. yy Neither the name of Sparta, Inc nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
1.11. "Source Code" means the preferred form of the Covered Code for making modifications to it, including all modules it contains, plus any associated interface definition files, scripts used to control compilation and installation of an Executable, or source code differential comparisons against either the Original Code or another well known, available Covered Code of the Contributor’s choice.
provides that the language of a contract shall be construed against the drafter shall not apply to this License. 12. RESPONSIBILITY FOR CLAIMS. As between Initial Developer and the Contributors, each party is responsible for claims and damages arising, directly or indirectly, out of its utilization of rights under this License and You agree to work with Initial Developer and Contributors to distribute such responsibility on an equitable basis.
16. "Patch for Modification" means a difference, program, system, or the like in order to create the Modified Source Code from the Source Code or the Binary Code thereof. 17. "Vicarious Execution of Patch Processing" means vicarious execution service to create the Modified Source Code applying the Patch for Modification to the Source Code or the Binary Code thereof. 18. "Source Code User" means a person who uses the Source Code. 19.
"Legal Entity" shall mean the union of the acting entity and all other entities that control, are controlled by, or are under common control with that entity. For the purposes of this definition, "control" means (i) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (ii) ownership of fifty percent (50%) or more of the outstanding shares, or (iii) beneficial ownership of such entity.
PHP 3.01 License The PHP License, version 3.01 Copyright (c) 1999 - 2010 The PHP Group. All rights reserved. Component Name License URL php-5.2.17 PHP 3.01 http://www.php.net/distributions Redistribution and use in source and binary forms, with or without modification, is permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
Head Office 6, Pangyo-ro 319 beon-gil, Bundang-gu, Seongnam-si, Gyeonggi-do, 463-400 Rep. of KOREA Tel : +82.70.7147.8753 Fax : +82.31.8018.3740 www.hanwha-security.com Hanwha Techwin America 500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666 Toll Free +1.877.213.1222 Direct +1.201.325.6920 Fax +1.201.373.0124 www.hanwhasecurity.com Hanwha Techwin Europe Heriot House, Heriot Road, Chertsey, Surrey, KT16 9DT, United Kingdom Tel +44.1932.57.8100 Fax +44.1932.57.8101 www.hanwha-security.eu User Manual ver.
