NETWORK VIDEO RECORDER User Manual Wisenet NVR
Network Video Recorder User Manual Copyright ©2020 Hanwha Techwin Co., Ltd. All rights reserved. Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
overview Important Safety Instructions Read these operating instructions carefully before using the unit. Standards Approvals Follow all the safety instructions listed below. Keep these operating instructions handy for future reference. Read these instructions. 3) Heed all warnings. 2) 4) 5) 6) 7) 8) 9) Keep these instructions. Follow all instructions. Do not use this apparatus near water. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.
overview CAUTION • RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. • Do not ingest battery, Chemical Burn Hazard. • This product contains a coin / button cell battery. If the coin / button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. • Keep new and used batteries away from children.
Contents overview getting started 9 live 13 3 3 3 5 24 Important Safety Instructions Product User Manual Description Real-Time Event Monitoring 24 Check Event List 25 Event Instant Viewer Target Audience 24 Contents 25 How to Use the Product 25 25 Starting the system 12 Shutting down the System 26 Login 27 12 12 13 Install Wizard Instant Viewer Restarting the System 26 PTZ Mode 27 27 Screen Layout of the Live 14 Checking the System Status 15 Live Screen Menu 16 28 Check
overview AI search 36 play 39 setup 42 36 36 37 37 38 39 40 Person Search 61 S.M.A.R.
live viewer Screen Layout of the Live Viewer 82 Checking User ID 82 82 83 Checking the System Status Checking Camera List 84 84 85 83 Live Status 83 Network Status Changing Overall Channel Aspect Ratio Full Screen Mode 88 85 Check Layout List 85 Change of Layout Channel and Name 85 Delete Layout 86 Event Type and Camera Settings 87 Event Instant Viewer 87 94 91 Screen Layout of the Search Viewer 92 Text Search 92 93 93 97 Bookmark Search Search Results Export 94 Screen Layo
overview setup viewer 99 99 99 Screen Layout of the Setup Viewer Setting the Camera 99 99 Camera Register Channel Setup 100 Camera Setup 100 Profile Setup 101 Camera Password 101 Setting the Recording 101 Recording Schedule 101 Record Setup 102 Record Option 102 Setting the Event 102 Event Setup 103 Event Rule Setup 103 Alarm Input 103 ONVIF Setup 104 Schedule 104 Setting the Device 104 Storage Device 105 Monitor 106 Text 106 Setting the Network 106 Interface 107 DDNS 107 IP Filtering 107 H
getting started StArting tHe SySteM inStAll wiZArd As shown below, proceed through each step of the . 1. Connect the power cable of the recorder to the wall outlet. Install Wizard can only be accessed at factory reset. If you do not want to proceed, click . 2. You will see the initialization screen. The initialization process will last about 2 minute. If a new HDD is installed, the initialization process may take longer. monitor. 1.
getting started Setting up the network The network port can be used as a common port for camera and web viewer connection. If a product supports two or more, then each network port will provide the following features. Click of the network connected to the recorder. 3. Set the administrator password on the screen and click the . Click < > to view the basic guide for setting a password. Refer to the password setup rules.
5. Set the date, time, time zone, and daylight saving time on the screen, and then click the . 7. On the screen, you can view the camera videos registered to each channel in thumbnails along with thumbnail information. To change the camera video position, select a video and drag and drop it to the desired location. ● getting StArted 6. On the screen, select a camera to register from the searched camera list and click .
getting started Shutting down the System Login 2. The "Shutdown" confirmation pop-up window will appear. 1. Select at the top right of the screen. 1. Select at the top right of the screen. 3. Click on . The system will shut down. To use the Recorder menu, you are required to login as a user that is authorized to access the applicable menu. 2. The dialog appears. 3. Enter the user ID and password, then click .
live Shows the video of the camera connected to the recorder. Also, you can adjust the camera and check the network transfer status. Screen Layout of the Live Item Saves the recorded video of the selected channel in the designated path in a recorder or SEC format. Clears the alarm in the event list and stops the alarm at the notification display of the system status. f The live screen is built as follows. Description ● live Activates the manual recording function of the recorder.
live Checking the System Status The icon at the top of the screen indicates the status of the system. Item It is displayed when an ISCSI device is disconnected. Description `` Only provided for products that support iSCSI. It is displayed when the network is overloaded. `` It occurs when the max receiving allowance is exceeded, causing an overload to the CPU. It disappears when you modify the Delete Camera or Set Camera to reduce the data rate. Displayed if the server has firmware to update.
Check Camera List Live Screen Menu Displays the camera type, status, and name registered in the recorder. After selecting the desired channel on the split mode, roll the mouse cursor over the screen to see the live screen menu. The live screen menu appears differently depending on the recorder operation status or the type of the registered camera. Itrem a Channel information Camera type Description Displays channel information (channel number, video window assignment, and color indication).
live Icons on the Live Screen Item You can check the status or operation with the icons on the live screen. Event Display `` The icons displayed on the screen may differ depending on the type of camera and the user's authority. Description Events from the recorder and camera are displayed in icons. For details, refer to the "Setup > Setting the Event > Event rule setup" page in the Table of Contents. It is displayed on the channels that can enable the PTZ mode. Displays AUDIO ON/OFF.
Live Screen Mode `` Each product may support different split view modes. You can display your camera's live video in various split modes. `` The 'Live4NVR' profile is added automatically with network camera auto registration, and settings can be changed according to user environment. add the Live4NVR profile. CH1 `` When system overloaded and the performance is down, network camera may play only main frame(I-frame).
live Switching the Split Mode Manual Switching Click You can split the live video from cameras to Single, 4-split, 9-Split, or 16-split mode and watch them one by one. or at the bottom of the screen or enter a page number to go to that page. `` Each product supports different split modes. Auto Sequence To switch the screen automatically, click < > at the bottom of the screen. You can monitor the split mode of your own choice by switching one after another at a certain interval.
OSD Information Display You can show or hide the recording status, camera status, event display, etc. in the video window. To show or hide the OSD information, click < > at the bottom of the screen. Channel Information Display You can check the information of the video being recorded with each camera. To check the channel information, click < > at the bottom of the screen. ● live The information of the current video is displayed on the live video which is being monitored. 800x448 (H.
live check the camera Status You can check the status of all cameras connected to the recorder. To check the camera status, click < > at the bottom of the screen. live Status Select in the menu to check the transmitted data from a network camera connected to each channel. record Status If you select in the menu, you can check the profile, record type, frame rate (Input/Record), and bit rate (Limit/Input/Record) for each channel.
CH1 CH2 CH2 CH3 CH6 CH4 CH8 CH10 network Status CH5 CH6 CH7 CH8 CH1 CH1 CH2 CH2 CH3 CH3 CH4 CH4 CH9 CH9 CH10 CH10 CH11 CH11 CH12 CH12 CH13 CH13 CH14 CH14 CH15 CH15 CH16 CH16 CH3 CH4 CH5 CH7 CH11 CH1 CH19 CH12 CH13 CH1 CH1 CH2 CH2 CH4 CH5 changing overall channel Aspect ratio CH3 CH1 CH1 CH2 CH6 Select in the menu to check the status ofCH2network bandwidth currently being received/ CH5 CH6 CH7 CH8 CH1 CH2 CH5 CH6 CH7 CH8 CH1 CH1 CH3 CH4 CH7 CH8 C
live full Screen Mode You can change to full screen mode, which has no top/bottom/left/right areas of the live screen. Click < > at the bottom of the screen. Setting uP tHe live lAyout This section outlines how to select a series of channels based on their purpose/accessibility and monitor them in a single layout.
change of layout channel and name 1. Click < > after selecting a layout. 3. Click < > to save the changed settings. 2. Add or delete channels or rename layouts. Play layout Sequence Click < Play sequence> at the bottom of the layout list to automatically switch the layout according to the sequence settings. ● live delete layout Click < > after selecting the layout to delete. ` You cannot delete the default layout.
live Real-Time Event Monitoring Real-time events that occurred on the device can be checked in the live video window and event list. `` AI browse events are only available for products that support AI. Check Event List Click < Event Search You can browse events by camera and event type. To search for a specific event, click < > to select the event type and camera to browse. Event filter Displays only selected events in the event list.
Event Instant Viewer Select an event to check from the event list, and click < occurred. > to play the recorded video at the time the event `` Instant viewer can play an event video for 1 minute. `` For AI events, the best shot and details of the event that occurred are displayed. Camera Video Control By using the function icon of the video window, you can easily use the functions of capture, video zoom, PTZ camera and thermal imaging camera.
live Instant Viewer You can move the video back 30 seconds and play it while live monitoring. Instant viewer plays video from 30 seconds to 1 minute from the current time. Select the desired channel and click < The Instant Viewer screen appears. • • • / >. PTZ Mode You can run PTZ control of the selected channel. Select the desired channel and click < Enters the PTZ control mode. >. `` Depending on the camera, the PTZ control function and speed may be different. : The video is played/stopped.
Digital Zoom Display Text You can zoom in or out the video via digital zoom. Select the desired channel and click < Enters the digital zoom mode. `` This is executable when a text device is connected. `` The Recorder can display text on a live screen when a text device is set. For details, refer to the "Setup > Setting the Device > Text" page in the Table of Contents. > to run the digital zoom.
live change channel Aspect ratio You can change the aspect ratio of each channel. Select the desired channel and click < >. It changes to the actual proportion of the video. PtZ control With this Recorder, you can configure the settings of a PTZ camera as well as commercial cameras in the market to your preference. This is active only if a channel that a PTZ camera is connected to is selected.
Item a b Description Zoom out/Zoom in Manual Focus You can adjust the focus manually. You can adjust the focus automatically. 1. Register a camera that supports the D-PTZ profile. ` In cameras that support the D-PTZ profile, you can use the D-PTZ function. 2. Both cameras that support general PTZ and cameras that support D-PTZ can control the live image using some of the function menus. ` For more information about the supported functions, please refer to the camera manual.
live to delete a registered preset 1. Click < 2. Click < You can search the storage device to be exported and export the recorded video of the desired time by layout or channel. >. >. "delete preset" window will appear. 3. Click < exPorting tHe recorded video 1. Click < > at the bottom of the screen. 2. The export setup screen will appear. > to select the preset to delete. 4. Click . The selected preset will be deleted. running Preset 1. Click < >. 2.
`` If you insert a USB memory stick with insufficient storage space, volume calculation may be disabled. Format the memory stick or delete some of the data on the memory stick to secure adequate storage space. `` The operation speed of the product may slow down if the export is in which is a progress. `` You can switch to the menu screen during export progress, but data playback will not be possible. `` Data can be played in the web viewer during export progress, but audio will not be supported.
search Time Search You can search recorded video by various conditions such as time, event, and export. Screen Layout of the Search You can search the recorded data by the desired date and time conditions. `` The time displayed will be based on the time zone and daylight saving time (DST) applied time zone, so it may be displayed differently depending on whether the data time zone recorded at the same time and daylight saving time (DST) is applied. a b f c d 1.
Event Search Text Search 1. Select in the menu. 1. Select in the menu. You can search for various events by channel. You can search the data input to the POS device connected to the recorder. ● search 2. Select a channel to search. `` If you select a channel to search, you can change the channel display mode by clicking < or dragging it from the channel table, and clicking the channel in the channel list. >.
search Export Search You can search the exported data on the connected storage media. Only data saved in recorder file format when exported will be retrieved. 1. Select in the . 2. When you click on the storage device selection, the device search window is displayed. Click < Storage Media. 3. Click . Exported file information will be displayed. • Folder : Displays the folder where files are stored. • Name : Displays the saved file name.
booKMArK SeArcH SMArt SeArcH You can search for bookmarked data. You can search for events by selecting a region of interest, an exclusive region, or a virtual line from a recorded video at a specific time. ` To use smart search, you need to set the area of the camera's “Motion Detection" or “IVA” to the entire area. However, if you want 1. Click < > on the video window menu. 2. Set the smart search area in the video window. 1. Select in the menu.
AI search If there is AI data recorded by the camera, you can search for images in various conditions such as people, faces, and vehicles. Screen Layout of the AI Search Person Search In the recorded data, you can search for a person by any condition you want, such as gender, top/bottom color. a f b c d 1. Select in the menu. 2. Select a channel to search.
Face Search Vehicle Search 1. Select in the menu. 1. Select in the menu. From the recorded data, you can search faces according to your desired conditions such as gender and age. You can search the vehicle by setting the vehicle type and color conditions from the recorded data. ● AI search 2. Select a channel to search.
AI search LP Search You can search for the license plate number recognized in the recorded data. 1. Select in the menu. 2. Select a channel to search. `` If you select a channel to search, you can change the channel display mode by clicking < or dragging it from the channel table, and clicking the channel in the channel list. >. You can select a desired channel by clicking 3. Select a date and time to search. 4. Select the overlapped data.
play You can play the recorded data and export the video you want during playback. Item Screen Layout of the Play a m f g d hi e Item a Video control You can use the video control function. `` `` `` `` `` `` l k j Description Select channel j Time line k Show/Hide Channel l m You can move by selecting a channel. Move the playback position and display event data. You can change the number of channels displayed in the time line. `` Up to 4 channels of time line can be displayed.
play PlAy SeArcH reSultS time line Adjustment You can move the playback position and zoom the time line in and out. • Click the desired play position in the time line. The playback start position will be moved. ` Click the start point on the left side of the time line to move the playback position to the start point of the first video. ` Place your mouse over the time line to see the corresponding thumbnail of the recorded video.
SeArcH reSultS exPort You can export the search results to a file. 1. Click the < > button. 2. Select a layout and channel to export. ● PlAy 3. Select a start date/time and an end date/time. ` If you changed the time zone of the device, select whether to apply DST. 4. Select the overlapped data. It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected time. 5. Click < > to select a storage device. 6. Please select a storage file type.
setup Sets the camera, recording, event, device, network, and system environment. Screen lAyout of tHe SetuP Setting tHe cAMerA You can access to the channel setup, camera settings, and profiles and camera password-related settings. Setting the channel a You can register a network camera for each channel and make connection between. Setup > camera > channel setup b c d e Item Description • : Displays the camera of the corresponding channel as a list or a thumbnail.
registering a network camera Manually 1. In the field, click on the button. 1. In the field, click on the button. ● SetuP Automatic registration of network cameras 2. The Auto detect window will be displayed. ` Click < > in the device list on the live screen to automatically search and register the camera. 3. Select a camera to register in the list and press the button.
setup • Address type : Select an address type of the camera. `` The supported address type may differ depending on the type of the connected product. - Static(IPv4)/Static(IPv6) : Used to provide the IP address of the camera manually. - Wisenet DDNS : This is available only if the camera is registered with the Wisenet DDNS(ddns. hanwhasecurity.com) server. Provide the registered domain for DDNS ID. Example) http ://ddns.hanwha-security.
network camera firmware upgrade Setting the camera functions You can set the camera while viewing the live video of the selected camera. Setup > camera > camera setup ● SetuP • Channel : Displays channel information. • Model : Displays the camera model information. • Current version : Displays the current camera firmware version. • Upgrade version : Displays the firmware version to upgrade. - Press the < - < > button to select the firmware manually within the USB.
setup • SSNR : Adjusts the brightness by reducing noise and minimizing afterimages even in dark places. Setting the Profiles • IRIS/Lens : Adjusts the brightness by automatically or manually adjusting the camera IRIS and lens. Setting the recording Profile • Sens-up : Automatically adjusts the shutter speed according to the brightness of the current light. • AGC : Adjust the brightness by amplifying the camera's electrical signal when images are shot in the dark.
Setting the live Profile You can change the live transfer settings of the network camera. Setting the remote Profile You can set the video profile transmitted to the network. Setup > camera > Profile > live Setup > camera > Profile > remote ● SetuP • : Displays the camera of the corresponding channel as a list or a thumbnail. • Camera name : Display the camera name. • IP address : Display the IP address of a camera. • Live replacement : You can select the live profile setup mode.
setup editing the Profiles You can change the video settings of a registered network camera for each channel. Setup > camera > Profile dewarping Setup Press the button at the bottom of the window to go to the distortion correction setup popup window for each channel. • Profile : Displays the profile type. • Video output/view : Sets the video output/view mode for each profile type.
How to set wiseStream dynamic gov/fPS setup Press the button at the bottom of the screen to go to the WiseStream setup popup window for the channel. At the bottom of the screen, press the button to open the dynamic GOV/FPS setup popup for the channel. Function to analyze the complexity of the video and effectively reduce the data size while maintaining the quality.
setup Setting camera Password You can change the passwords of all registered cameras at once. You can register the camera’s ID and password. Setup > camera > camera password Setting tHe recording You can setup scheduled recording, event recording and other recording related settings. recording Schedule If you set a recording schedule for a specific date and time, the recording will start at that specific time.
record Setup You can set the resolution and number of recordings for each channel when an event occurs or during a normal recording. You can check frame rates and data transfer amount of Full Frame and Key Frame recordings for each channel, and set the transfer limit for recordings. recording even when the channel is configured to recording mode. For Key Frame recording channels, the icon for limited recording appears on the live screen's top side.
setup Setting the Event You can set the event-related settings such as whether or not an event is detected for each channel and whether an alarm occurs Motion Setup > Event > Event setup > Motion Event setup You can set whether or not to detect the detailed events (object detection, motion detection, intelligent video analytics, tampering) from the camera for each channel and details. Setup > Event > Event setup • Object : You can set detailed settings for object detection of the connected camera.
Tampering IVA Setup > Event > Event setup > IVA Setup > Event > Event setup > Tampering ● setup • IVA : You can set whether to enable intelligent video analytics. • Type : You can set a virtual line, virtual area, and detection excluded area. - Virtual line : Set the virtual line to enable intelligent video analytics. - Virtual area : Set the area to enable intelligent video analytics. You can set the details of virtual areas to fit your purposes.
setup event rule Setup • Event action : Displays the event action set in the event rule. Item You can set the event trigger and action rule to output an alarm when an event occurs. Setup > event > event rule setup Description PTZ preset setting Alarm output and beep setting E-mail recipient setting Mobile push receive setting Event monitoring duration setting • Edit : Changes the registered event rule.
• Event action : Press <+ Add action> to set the event action. - PTZ Preset : Set the PTZ preset to be displayed when an event occurs. Click < for each channel. > to set camera presets - Alarm out : Set the alarm out to be generated when an event occurs. Select the output terminal according to the number of alarm terminals on the device to set the alarm duration. You can set the operation of the alarm sensor.
setup Schedule When setting the event rule, you can set the operating time of the event action. Setup > Event > Schedule Setting the Device You can make the detailed settings for devices such as storage device and monitors. Storage Device You can set the storage device usage and check the setting status. Device/Format You can check storage devices and their capacity, usage as well as status. The connectable storage devices are HDD and USB.
• Storage Status : Displays the working status of a storage device. Click the to display the storage status window. `` The ARB feature is available only when your video is saved in the SD card after registering your Wisenet camera using the Wisenet protocol. This is only supported in SUNAPI 2.3.2 or later. - Red : Displays the situation of video loss. `` Set the profile bitrate used for recording a video in the SD card of camera to 6144 kbps or below.
setup Connecting the iSCSI This function is only available for products that support iSCSI. Adding an iSCSI device When connecting an iSCSI device to the recorder, you can search for the iSCSI device and connect and disconnect it. Setup > Device> Storage device > iSCSI • Add : Add an iSCSI device. • Delete : Delete the registered iSCSI device. • Model : Displays the iSCSI model name. • iSCSI Usable Name : It displays the name of iSCSI in compliance with the iSCSI protocol format.
RAID mode setting Setup > Device> Storage device > RAID This function is only available for products that support RAID. If you enable the RAID (Redundant Array of Independent Disks) mode, you can safely recover your data even if your system HDD is damaged. • RAID for each product RAID level 5 and 6 are supported. ● setup Product RAID type `` RAID level 5 : You can recover the operation and data of only one malfunctioning HDD out of all the HDDs XRN-3210B4 XRN-6410B4 XRN-6410DB4 in the RAID array.
setup Distributed Recording RAID mode setting 1. Click on the
S.M.A.r.t You can check the connection status and details of the hard disk mounted in the recorder. Setup > device> Storage device > S.M.A.r.t Monitor You can set the information displayed on the monitor as well as the output system. Setup > device > Monitor ● SetuP Monitor settings You can set the monitor output related screen displays, switching time, video display, etc. • Display : Only checked items among date, time, channel name and icon will be displayed on the monitor screen.
setup expansion monitor settings This function is only available for products that support the use of an extended monitor. 1. Select for video display and click . You can change the layout of the extended monitor. 2. Select split mode in the layout mode. 3. Select as many channels on the channel table as the number of channels selected in layout mode, and you can view the applicable screens on the monitor.
text registering a text device You can set the POS device setting to send text information and text event information. device Settings You can make detailed settings for the POS device connected to the recorder. ● SetuP Setup > device > text > device • Device : Displays the text device name registered by the user. • Use : Specifies whether to enable text device. • CH : Select a channel to add a device from a channel table. • Port : Display a port number that is set.
setup text event Settings You can set the text to receive an alarm when an event occurs. Setup > device > text > event Setting tHe networK You can set various network functions, such as monitoring live video by connecting to a network from a remote location and receiving an event by e-mail. interface You can set the network connection route and protocol. Setting a network connection Sets the protocol and environment of the network.
connecting and Setting the network • Setting the dHcP iP Address of the broadband router when no router is used 2. At this stage, make the local PC's windows network configurations to the below example : example) IP : 192.168.1.2 Subnet Mask : 255.255.255.0 Gateway : 192.168.1.1 Networking may differ from the connection method, check your environment before setting the connection mode. • Static mode - Network Settings : Set the in menu of the connected Recorder to .
setup ddnS If a remote user accesses the network, you can set whether or not to use DDNS and the site to be connected. Setup > network > ddnS to check Quick connect status A progress bar and its message appears for a Quick Connect. • Quick connect Success : Message for a successful connection. • invalid network configuration : Message appears if the network configuration is not valid. Check the configuration. • Please enable uPnP function of the router.
iP filtering You can prepare the list of IP addresses to allow or block access to a specific IP address. Setup > network > iP filtering HttPS You can choose a secured connection system or install a certificate. Setup > network > HttPS ● SetuP • Filtering type - Deny : If you select reject, access to the registered IP address will be limited. - Allow : If you choose permit, then they can only access the registered IP addresses. • Use : Select whether to enable registered IP filtering.
setup 802.1x e-mail 802.1x is an authentication system between a server and a client, which prevents hacking, virus infection, and information leakage of transmitted and received network data. SMtP Setting When connecting to a network, you can select whether to use the 802.1x protocol and install a corresponding certificate. 802.1x can be used to block the unauthorized client access and increase security by allowing only authenticated users to communicate. Setup > network > 802.
event Setting You can set the interval and type of the event that will be sent to the user. Setup > network > e-mail > event SnMP The SNMP protocol allows system or network administrators to remotely monitor and configure the network devices. Setup > network > SnMP ● SetuP • Event Interval : Set the event interval. ` If a series of events occurs, the e-mail will be sent at the specified interval, not on each event.
setup dHcP Server You can set the internal DHCP server and assign an IP address to the network camera. network Setting check iP You can check the IP address assigned to the current DHCP server, MAC address, and the connected network port information. Setup > network > dHcP Server > check iP Setup > network > dHcP server > network • Network : You can set the IP range and time to activate as the recorder's DHCP server.
to set troubleshooting 1. Set one recorder to mode and the other recorder to mode. 2. In the recorder set to mode, enter the viewer port IP and administrator password of the recorder you want to connect to and click under the status display. Setup > network > failover • Device List/Status : Shows the status of the general recorder currently connected to the standby recorder.
setup P2P This function is only available for products that support P2P. You can connect the recorder to Wisenet Mobile for easy use when using P2P service. Setup > network > P2P Setting tHe SySteM You can set the date, language, authority, etc. displayed when using the system, and query system information or log information. date/time/language You can check and setup the current Date/Time and time related properties, as well as the language used for the interface on the screen.
• Holiday : A user can select specific dates as holidays according to their own preferences. Select a holiday from the calendar displayed by clicking . - The same applies to or settings as holidays. user You can manage users, such as adding or deleting users and granting different authorities for each user.
setup user setting You can create user groups and set authorities for each group. You can manage user information such as registering and deleting users in the created user group. if you want to register a user Setup > System > user > user 1. Click on the < > button to launch the user addition popup window. To add a user, click on . if you want to add a group 1. Click on the < > button to launch the Group Addition popup window. If you want to add a group, click on . 2.
Setting Permissions Set user's restricted access or network restriction. Items with restrictions will require logging in for use. Setup > System > user > Permission Setup if the user has restricted access If a general user selects a menu to which they do not have access, an access restriction confirmation window will be displayed. If all rights are restricted, only the accessible menu of the live screen menu will be displayed, and only the user's own password can be changed.
setup System Management To upgrade the current software version You can check the current system version and update to a new version, export data, setting initialization, and more. Checking the System information You can check the current software version and MAC address before proceeding with the upgrade. Setup > System > System management > System information 1. Connect a device storing the software to be updated. `` It may take about 10 seconds to recognize the device.
Settings You can export the information set in the recorder to a storage device and apply the same information to other recorders. Setup > System > System management > Settings log information You can check the log information related to system, events, and export. checking the system log Setup > System > log information > System log • Storage device : Shows the connected storage device. - Press the < > button to view the list of storage devices.
setup checking the event log You can search recorded events including alarms, camera events and video loss. It also shows the log and its timestamp. Setup > System > log information > event log checking the export log You can search the user who performed the export and the execution time and details (time, channel, device, file type).
starting web viewer wHAt iS web viewer? Web Viewer is a software program with which the operator can access a remote Recorder for real-time monitoring, PTZ control (if configured) or search. connecting web viewer 1. Open your web browser and type the IP address or URL of Recorder into the URL address box. 2. A user with the admin permissions should provide the admin ID and password. A registered user should provide the user ID and password.
starting web viewer Install Wizard As shown below, proceed through each step of the . 3. Set the network connection type and the connection environment on the screen, and then click the button. Install Wizard can only be accessed at factory reset. If you do not want to proceed, click . `` When you complete installation using the install wizard on your recorder, the install wizard will not appear on your web viewer. 1.
live viewer You can check the video from camera registered in the Recorder connected from a remote PC. Also, you can adjust the camera and check the network transfer status. Screen Layout of the Live Viewer a Menu Enables the Manual recording function of the recorder. g Saves the video saved in the set time of the selected channel in PC in AVI format. p h Clears the alarm in the event list and stops the alarm at the notification display of the system status.
live viewer Checking the System Status The icon at the top of the screen indicates the status of the system. Name Description Displayed when a problem occurs with the pan or recording status. Checking Camera List Displays the camera type, status, and name registered in the recorder. Live > List Displayed when an error occurs in the power supply. Displayed when the amount of input data by channel exceeds the set amount of data limit.
Checking the All Camera Status You can check the status of all cameras connected to the recorder. Live Status Click the < > button, followed by the tab. You can check the status of network bandwidth currently being received/transmitted. > button. You can check the status and transmission information of the camera connected to each ● live viewer Click the < channel. Network Status `` To change the profile setup, click the button.
live viewer Changing Overall Channel Aspect Ratio Full Screen Mode Click < Click < Video screen ratio for all channels can be changed in live split screen mode. > at the bottom of the screen. It changes to the actual proportion of the video. If you want to go back to the previous screen ratio, click < > again. You can change to full screen mode, which has no top/bottom/left/right areas of the live screen. > at the bottom of the screen.
Setting up the Live Layout This section outlines how to select a series of channels based on their purpose/accessibility and monitor them in a single layout. Live > List 1. Click < > after selecting a layout. 3. Click < > to save the changed settings. 2. Add or delete channels or rename layouts. Delete Layout Click < • • • • • ● live viewer Check Layout List Change of Layout Channel and Name > after selecting the layout to delete. : Create a new layout.
live viewer Real-Time Event Monitoring Real-time events that occurred on the device can be checked in the live video window and event list. `` AI browse events are only available for products that support AI. Check Event List When new events occur, the list of events will be updated accordingly. `` The specified channels and events are displayed in the list according to the event rule setup. For details, refer to the "Setup > Setting the Event > Event rule setup" page in the Table of Contents.
Event Instant Viewer Select an event to check from the event list, and click < occurred. > to play the recorded video at the time the event `` Instant viewer can play an event video for 1 minute. `` For AI events, the best shot and details of the event that occurred are displayed. Live Screen Menu After selecting the desired channel on the split mode, roll the mouse cursor over the screen to see the live screen menu.
live viewer Camera Video Control By using the function icon in the video window, you can easily enable functions such as screenshot, video rotation, and PTZ control. PTZ Mode You can run PTZ control of the selected channel. Select the desired channel and click < >. Enters the PTZ control mode. Capture Select a channel to capture video and click the < `` Depending on the camera, the PTZ control function and speed may be different. > button. The captured image is saved as .
PTZ Control Performing Digital Zoom You can zoom in or out using the mouse wheel. If you scroll up using the mouse wheel, the selected video screen is enlarged by 10%, and a thumbnail window is displayed. If the connected network camera is a PTZ camera, the < camera channel is selected, you can control the PTZ. > icon is displayed in the camera list. When the ● live viewer `` Scrolling up/down using the mouse wheel will zoom in/out the video screen by 10%.
live viewer Using Digital PTZ (D-PTZ) function 1. Register a camera that supports the D-PTZ profile. Running Preset 1. Click < >. `` In cameras that support the D-PTZ profile, you can use the D-PTZ function. 2. Double-click the preset you want to run from the list. The camera lens moves to the set position. `` For more information about the supported functions, please refer to the camera manual. Running Swing (auto pan), Group (scan), Tour, or Trace (pattern) 2.
search viewer You can search and play the recorded video stored in the recorder by connecting the recorder remotely. Name Screen Layout of the Search Viewer a c d e f l g REC REC REC 90 90 90REC REC 90 90 Name 90 REC Menu b Search menu tab Shows detailed search menu. c Select channel Displays the search channels. Turns on/off the section setup. f Saves the video of the selected channel in the designated path in AVI format.
search viewer Time Search You can search the recorded data by the desired date and time conditions. `` The time displayed will be based on the time zone and daylight saving time (DST) applied time zone, so it may be displayed differently Text Search You can search the data input to the POS device connected to the recorder. depending on whether the data time zone recorded at the same time and daylight saving time (DST) is applied. 1. Select < 1. Select < > in the menu. 2.
Bookmark Search You can search for bookmarked data. Search Results Export Search results of events, texts and bookmarks can be exported to a file. Example) Bookmark search result export 1. Click < > in the search results list. ● search viewer 1. Select < > in the menu. 2. Select a channel to search. 3. Select the date and time to search. 4. Click the button. The bookmark search results will be displayed. Click the desired bookmark list to play.
AI search viewer If there is AI data recorded by the camera, you can search for images in various conditions such as people, faces, and vehicles. Screen Layout of the AI Search Viewer Person Search In the recorded data, you can search for a person by any condition you want, such as gender, top/bottom color. a b f c 1. Select in the menu. d 2. Select a channel to search. 3. Select the date and time to search.
Face Search Vehicle Search 1. Select in the menu. 1. Select in the menu. 3. Select the date and time to search. 3. Select the date and time to search. From the recorded data, you can search faces according to your desired conditions such as gender and age. You can search the vehicle by setting the vehicle type and color conditions from the recorded data. ● AI search viewer 2. Select a channel to search. 4. Select a detailed search option.
AI search viewer LP Search You can search for the license plate number recognized in the recorded data. Search Results Export Search results such as people, faces, and vehicles can be exported to a file. Example) Person search results export 1. Click < > in the search results list. 1. Select in the menu. 2. Select a channel to search. 3. Select the date and time to search. 4. Click the button. • Channel : Displays the recorded channel.
play Play Search Results You can play the recorded data and export the video you want during playback. To Adjust the Time Line • Click the desired play position in the time line. The playback start position will be moved. You can select the desired section from the time line or search list during video playing and export it to a file. 1. Click the < > button 3. Click the < > button. 2. Select the start and end points of the desired section in the time line with the mouse.
play Play Button Name and Function Paused state a b c d h i e f Playback state g Name Description a Previous event Go to the previous event video. b Step backward Move backward one frame c Play d Step forward e Next event f Speed g Backward X times playback h Freeze i Forward X times playback 98_ play Play the video. Moves forward one frame or more. Go to the next event video. Select the video playback speed.
setup viewer Setting the Camera You can configure the Recorder settings remotely on the network. Screen Layout of the Setup Viewer You can check a list of cameras that are connected to the Recorder and configure the necessary settings. For details, refer to the "Setup > Setting the Camera" page in the Table of Contents. a Camera Register ● setup viewer You can add a network camera(s).
setup viewer camera Setup Profile Setup You can change the settings of a connected network camera. You can set the profile for a network camera. Setup > camera > camera setup Setup > camera > Profile setup record You can set the recording profile for a network camera. • When you click the button, a new camera web browser window is opened. - This is not supported if the camera is connected to the RTSP protocol.
Remote You can set the video profile transmitted to the network and the expansion monitor. Setting the Recording For details, refer to the "Setup > Setting the Recording" page in the Table of Contents. Recording Schedule Setup > Record > Recording schedule Camera Password You can change the passwords of all registered cameras at once. Setup > Camera > Camera password Record Setup Select a type of the normal/event recording frame rate for each channel.
setup viewer Record Option You can set the hard disk recording option. `` You can set the recording duration separately for each channel. Setup > Record > Record option Setting the Event For details, refer to the "Setup > Setting the Event" page in the Table of Contents. Event Setup You can set detailed settings for each channel's event detection mode. Setup > Event > Event setup Object detection You can change the AI object detection event setup.
Tampering detection You can change the tampering detection event setup. Alarm Input You can set the operation of the alarm sensor. Setup > Event > Alarm input ● setup viewer Event Rule Setup You can set the event trigger and action rule to output an alarm when an event occurs. Setup > Event > Event rule setup ONVIF Setup You can set the camera registered with the Onvif protocol.
setup viewer Schedule Whether to output an alarm can be scheduled according to the day and time. The initial setting will be an event sync, and an alarm will be sent only when an event occurs. Setup > Event > Schedule Setting the Device You can check a list of devices that are connected to the Recorder and configure the necessary settings. For details, refer to the "Setup > Setting the Device" page in the Table of Contents.
RAID S.M.A.R.T Distributed recording Monitor You can set the RAID (Redundant Array of Independent Disks) mode. You can check the connection status and details of the hard disk mounted in the recorder. ● setup viewer By allocating a certain portion of HDDs to each group, you can distribute the amount of recording for optimal saving. You can set the information displayed on the monitor as well as the output system.
setup viewer Text You can set the device text display and event text settings. Setup > Device > Text Device Relevant values of a device connected to Recorder can be set. Setting the Network For details, refer to the "Setup > Setting the Network" page in the Table of Contents. Interface A remote user can access the Recorder via the network to check the current mode and the IP address. Setup > Network > Interface Network Specify the network connection path.
DDNS You can set DDNS. Setup > Network > DDNS HTTPS You can select a security connection system or install public certificates. Setup > Network > HTTPS ● setup viewer IP Filtering You can prepare the list of IP address to allow or block accesses to a specific IP address. Setup > Network > IP filtering `` While using HTTPS, if you want to switch to HTTP, then abnormal operation can take place as the browser contains the setting values.
setup viewer E-mail You can specify the SMTP server that sends a mail if an event occurs and set the recipient group and users. Recipient You can set groups and recipients to receive emails. Setup > Network > E-mail SMTP You can set the server that sends mails and specify if you use the authentication process. SNMP Using the SNMP protocol, the system or network administrator can remotely monitoring the network devices and sets the environment.
DHCP Server You can set the network camera IP address and check the details by setting up a DHCP server. Setup > Network > DHCP server This function is only available for products that support P2P. If you want to use P2P service, check the box. You need to scan the QR code on the screen to use the P2P service. Setup > Network > P2P ● setup viewer Network P2P You can set the internal DHCP server and assign an IP address to the network camera.
setup viewer Setting the System You can configure the various settings of the Recorder system. For details, refer to the "Setup > Setting the System" page in the Table of Contents. Date/Time/Language You can check and setup the current Date/Time and time related properties, as well as the language used for the interface on the screen. User You can manage users, such as adding or deleting users and granting different authorities for each user.
Permission setup You can set the user permission. Settings Using a storage device, you can apply the current configuration of Recorder to another Recorder. Press the Initialization button to return the network settings to their factory default state. Items in the category are excluded from the initialization. ● setup viewer System Management You can check the current system version and update to a new version, export data, setting initialization, and more.
setup viewer Event log The event log lists recorded events, such as sensor events, camera events, or image losses. Export log You can search the user who performed the export and the execution time and details (time, channel, device, file type).
export viewer SEC Backup Viewer Screen Layout of the Backup Viewer You can play a file that is backed up in the format of SEC. a Backup in SEC format produces backup data file, library file and self-executable viewer file. b c d e f g h i If you run the backup file viewer, the backup data file will be played. XRN-6410DB4_CAM 01 2020-05-14 20 :54 :13 H264(1920x1080), NONE PCs with a lower specification than the recommended below may not fully support forward/backward and highspeed playback.
export viewer Name Description Saves the current video's image as in an image file. Supports JPEG file format. d Screen Printout Prints out the current screen. You should have installed the appropriate printer driver before you can print out the screen. e Audio / A toggle button. Each time you press this button, the audio output will toggle between activated and deactivated. You can adjust the volume level from 0 to 100. f Watermark g Deinterlace You can enable the De-interlace function.
appendix Use Joystick The function is only available for the product that supports a joystick. For products that support joy stick, see page 4 "Products supporting each feature” of the Product Specification Manual. Using Virtual Keyboard The SPC-2000 joystick is operated as follows : d ● appendix a 1. For alphanumeric inputs, the virtual keyboard window appears. 2. Using a mouse, click on the desired character tab. b 3. Select . Entered word is applied.
appendix Troubleshooting Problem Live video will be slow or cut off. Action • The frame number set for multiple data transmission set in camera or network environment could differ from the actual rate of transmission. Click < > at the bottom of the screen to check the number of incoming frames per channel and the actual number of frames played. Basically, when you register a camera, the Live4NVR profile is created and the rate is set to H.264 800*448 30fps.
Problem Problem Action If I press the ESC key in full screen mode of the Web Viewer, the system does not switch to a normal split mode. • Press the ALT+TAB keys to select 'ACTIVE MOVIE' and press the ESC key again. The system will switch to a normal split mode. Frame rate of the actual recording does not match that of configured to the camera. It is difficult to configure the network for default search, export, and router use. • For more information, refer to the user manual.