COLOR MONITOR ZM-CR321NP-CP User Guide Before operating the unit, please read this manual thoroughly, and retain it for future reference.
IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Read these instructions. Keep these Instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Graphic Symbol Explanation The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated ‘dangerous voltage’ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
IMPORTANT SAFEGUARDS Caution Power source is indicated on the rear of the set. It contains high-voltage parts. If you remove the cover, it may cause fire or electric shock. Do not remove the cover by yourself. (Control switches are at the front of the monitor.) 1. Read Instructions : All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions : The safety and operating instructions should be retained for future reference. 3.
8. Accessories : Do not place this monitor on an unstable cart, stand, tripod, bracket or table. The monitor may fall, causing serious injury to a child or adult and serious damage to the appliance. Use only with a cart, stand, tripod. bracket or table recommended by Checkpoint or sold with the monitor. Any mounting of the monitor should follow Checkpoint’s instructions and should use a mounting accessory recommended by Checkpoint. 9.
13. Lightning : For added protection for this monitor during a lightning storm or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the monitor due to lightning and power-line surges. 14. Overloading : Do not overload wall outlets and extension cords as this can result in a risk of fire of electric shock. 15.
18. Replacement Parts : When replacement parts are required, be sure the service technician has used replacement parts specified by Checkpoint or have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock or other hazards. 19. Safety Check : Upon completion of any service or repairs to this monitor, ask the service technician to preform safety checks to determine that the monitor is in proper operating condition.
Information to user Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
IC Compliance Notice This Class (A) digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe (A) respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numéique de la classe A est conforme à la norme NMB-003 du Canada. Warning This is a class A product.
Contents IMPORTANT SAFETY INSTRUCTIONS .................Eng-2 IMPORTANT SAFEGUARDS................................... Eng-4 FCC information .......................................................... Eng-7 Front Panel Components and Controls ...................... Eng-11 • Using buttons on the front panel ..........................Eng-11 Rear Panel Components and Controls ....................... Eng-13 Connections ............................................................... Eng-14 Maintenance.............
Front Panel Components and Controls Using buttons on the front panel Power Switch On/off switch. If you press this button, the monitor is turned on and the LED of selected input signal is lit. VIDEO Input Selection Switch It selects video and audio input signal. To change input signal, press this button. VOLUME, DATA Control Switch VOLUME key has two functions : • Volume Controls • Data Controls : To change volume, press only this key.
CONTRAST Switch This control adjusts the contrast of the screen image. Press CONTRAST switch and then VOLUME(DATA) switch to control the contrast. BRIGHT Switch This control adjusts the bright of the screen image. Press BRIGHT switch and then VOLUME(DATA) switch to control the bright. COLOR Switch This control adjusts the color intensity of the screen image. Press COLOR switch and then VOLUME(DATA) switch to control the color intensity.
Rear Panel Components and Controls VIDEO LINE IN(A, B) Camera INPUT connector. Input connectors for up to 2 cameras VIDEO LINE OUT(A, B) Camera OUTPUT connector. VCR IN(VIDEO) VCR INPUT connector. Connect to the VCR. AUDIO LINE IN(A, B) AUDIO INPUT connector. Select corresponding AUDIO input signals AUDIO LINE OUT(A, B) AUDIO OUTPUT connector. AUDIO IN(VCR) VCR AUDIO INPUT connector.
Connections CCD Camera 1 CCD Camera 2 Eng-14
Maintenance If the quality of the picture on the COLOR MONITOR is poor and cannot be improved, inspect all system connections and cable runs. Repairs should be performed by a qualified technician with adequate test equipment and facilities.
Specifications System ZM-CR321NP-CP (NTSC/PAL) CRT 21” diagonal, 0.75mm stripe pitch, 90° deflection Video In/Out 2 Channel Input/2 Channel Output. VCR INPUT 1.0Vp-p BNC jack Audio In/Out 2 Channel Input/2 Channel output.
Memo Eng-17
COLOR MONITOR ZM-CR321NP-CP Mode d’emploi Pour profiter pleinement de votre moniteur, prenez le temps de lire attentivement ce mode d’emploi. Part No.
ATTENTION RISQUE DE DECHARGE ELECTRIQUE NE PAS OUVRIR ATTENTION : POUR REDUIRE LE RISQUE DE DECHARGE ELECTRIQUE, NE RETIREZ PAS LE CACHE (NI LE PANNEAU ARRIERE). AUCUNE PIECE NE PEUT ETRE REPAREE PAR L’UTILISATEUR. ADRESSEZ-VOUS AU PERSONNEL QUALIFIE POUR LE DEPANNAGE.
CONSIGNES IMPORTANTES Attention Le point d’alimentation est indiqué à l’arrière de l'appareil. Il contient des pièces sous haute tension. Si vous retirez le couvercle, un incendie ou une décharge électrique risque de se produire. Ne retirez pas vous-même le couvercle. (Les boutons de commande sont situés à l'avant du moniteur). 1. Lisez les consignes : Vous devez prendre connaissance de toutes les consignes de sécurité et d’utilisation avant la mise en marche de l’appareil. 2.
8. Accessoires : Ne placez pas ce moniteur sur un chariot, un socle, un trépied, une console ou une table instable. La chute du moniteur pourrait blesser grièvement un enfant ou un adulte et gravement endommager l'appareil. Utilisez uniquement un chariot, un socle, un trépied, une console ou une table recommandé(e) par le fabricant ou vendu(e) avec le moniteur. Suivez les consignes de Checkpoint lors du montage du moniteur et utilisez l'accessoire de montage recommandé par Checkpoint. 9.
13. Foudre : Afin d’assurer une protection supplémentaire pour le moniteur, débranchez-le de la prise murale et débranchez le connecteur du réseau câblé en cas d'orage ou d'absence et de non-utilisation prolongées. Cela évitera que le moniteur ne soit endommagé par la foudre et par des surtensions des lignes électriques. 14. Surcharge : Ne surchargez pas les prises murales ou les câbles de rallonge car cela crée un risque d’incendie ou de décharge électrique. 15.
18. Pièces de rechange : Lorsque des pièces de rechange sont nécessaires, assurez-vous que le technicien de dépannage utilise des pièces de rechange spécifiées par Checkpoint ou des pièces présentant les mêmes caractéristiques que les pièces d'origine. Des substitutions non autorisées peuvent provoquer un incendie, des décharges électriques et d’autres dommages. 19.
Table des matières CONSIGNES IMPORTANTES .................................. Fra-3 Commandes et composants de la façade....................... Fra-8 • Utilisation des boutons du panneau avant ..................Fra-8 Commandes et composants du panneau arrière ......... Fra-10 Branchements.............................................................. Fra-11 Entretien ......................................................................Fra-12 Caractéristiques techniques.........................................
Commandes et composants de la façade Utilisation des boutons du panneau avant Bouton POWER Bouton Marche/Arrêt. Appuyez sur ce bouton pour allumer le moniteur. La LED rouge du signal d’entrée sélectionné s’allume. Bouton VIDEO Input Selection (Sélection d’entrée VIDEO) Il sélectionne le signal d’entrée vidéo et audio. Pour changer le signal d’entrée, appuyez sur ce bouton.
Bouton CONTRAST (Contraste) Ce bouton règle le contraste de l’image affichée à l’écran. Appuyez sur le bouton CONTRAST, puis sur la touche VOLUME (DATA) pour régler le contraste. Bouton BRIGHT (Brillance) Ce bouton règle la brillance de l’image affichée à l’écran. Appuyez sur le bouton BRIGHT, puis sur la touche VOLUME (DATA) pour régler la brillance. Bouton COLOR (Couleur) Ce bouton règle l’intensité de la couleur de l’image affichée à l’écran.
Commandes et composants du panneau arrière VIDEO LINE IN(A, B) Connecteur INPUT (ENTREE) de la caméra. Connecteurs d’entrée de 2 caméras maximum VIDEO LINE OUT(A, B) Connecteur OUTPUT (SORTIE) de la caméra. VCR IN(VIDEO) Connecteur INPUT (ENTREE) du magnétoscope. Connexion au VCR (Magnétoscope). AUDIO LINE IN(A, B) Connecteur AUDIO INPUT (ENTREE AUDIO). Sélectionnez les signaux d’entrée AUDIO correspondants AUDIO LINE OUT(A, B) Connecteur AUDIO OUTPUT (SORTIE AUDIO).
Branchements Caméra 1 à dispositif à transfert de charge Caméra 2 à dispositif à transfert de charge Fra-11
Entretien Si la qualité d’image du MONITEUR COULEUR est mauvaise ou s’il est impossible de l’améliorer, contrôlez tous les branchements et les parcours de câbles. Les réparations doivent être effectuées par un technicien qualifié disposant d’installations et d’équipements de contrôle appropriés.
Caractéristiques techniques Système ZM-CR321NP-CP (NTSC/PAL) CRT Diagonale 21”, pas de masque de 0,75 mm ; déviation de 90° Entrée/sortie vidéo 2 canaux/Sortie 2 canal. ENTREE MAGNETOSCOPE prise BNC 1,0 Vp-p Entrée/sortie audio 2 canaux/Sortie 2 canal.