FRIGORIFEROCONGELATORE FRIDGE-FREEZER BFD 230 2223 257-71
WARNINGS It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can be acquainted with the functioning of the appliance and the relevant warnings.
• Do not place carbonated or fizzy drinks in the freezer as it creates pressure on the container, which may cause it to explode, resulting in damage to the appliance. Installation • During normal operation, the condenser and compressor at the back of the appliance heat up considerably. For safety reasons, minimum ventilation must be as shown in the relevant Figure. Attention: keep ventilation openings clear of obstruction.
Temperature regulation Storage of frozen food The temperature is automatically regulated and can be increased to achieve a higher temperature (warmer) by rotating the thermostat knob toward lower settings or reduced (colder) rotating the knob towards higher settings. However, the exact setting should be chosen keeping in mind that the temperature inside the refrigerator depends on: • room temperature; • how often the door is opened; • the quantity of food stored; • location of appliance.
Movable shelves The walls of the refrigerator are equipped with a series of runners so that the shelves can be positioned as desired. D338 Positioning the door shelves To permit storage of food packages of various sizes, the door shelves can be placed at different heights. To make these adjustments proceed as follows: Gradually pull the shelf in the direction of the arrows until it comes free, then reposition as required.
MAINTENANCE Unplug the appliance before carrying out any maintenance operation. Warning This appliance contains hydrocarbons in its cooling unit; maintenance and recharging must therefore only be carried out by authorized technicians. Periodic cleaning Periods of non-operation Clean the inside with warm water and bicarbonate of soda. Rinse and dry thoroughly.
The freezer compartment, however, will become progressively covered with frost. This should be removed with a plastic scraper, whenever the thickness of the frost exceeds 4 mm. During this operation it is not necessary to switch off the power supply or to remove the foodstuffs. However, when the ice becomes very thick on the inner liner, complete defrosting should be carried out and it is advisable to carry out this operation when the appliance is empty.
The Manufacturer declines all responsibility if the above safety precautions are not observed. This appliance complies with the following E.E.C. Directives: - 87/308 EEC of 2/6/87 relative to radio interference suppression. ATTENTION! It must be possible to disconnect the appliance from the mains power supply; the plug must therefore be easily accessible after installation. - 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3.5.
540 It is necessary that the niche is provided with a conduct of ventilation having the following dimensions: Depth 50 mm Width 3 2 540 mm Fit the appliance in the niche by making sure that it stands against the interior surface of the unit on the side where the door hinges of the appliances are fitted. Insert the appliance until the upper strip butts up against the unit (1) and make sure that the lower hinge is in line with the surface of the unit (2).
Separate parts Ha, Hb, Hc, Hd as shown in the figure Hb Ha Hc Hd PR266 ca. 50 mm Place guide (Ha) on the inside part of the furniture door, up and down as shown in the figure and mark the position of external holes. After having drilled holes, fix the guide with the screws supplied. 90° 21 m m 90° ca. 50 mm 21 m m Fix cover (Hc) on guide (Ha) until it clips into place. Ha Hc PR33 8mm Open the appliance door and the furniture door at 90°. Insert the small square (Hb) into guide (Ha).
Place the small square on the guide again and fix it with the screws supplied. Should the lining up of the furniture door be necessary, use the clearance of slots. At the end of operations, it is necessary to check if the door of the furniture closes properly. Hb PR168 Fix cover (Hd) on guide (Hb) until it clips into place.
Brandt italia spa Viale Europa, 5/7 - 25028 Verolanuova (BS) - Tel.030 9367.