Brushless DC Tubular Motor Operation Manual Tubular Motor Type： SS40E Remote Control Type： ZEN16SA、ZEN16DA
Table of Content Before Using Safety recautions 3 Name of Each Part 4 Installation 7 Settings Switch Setting Mode / User Mode Switch blind system 11 13 Set Connection Between Motor and Remote Control 14 Cancel the Connection 15 Switch Between Forward and Reverse Rotations 16 Set Upper and Lower limits 17 Set Group Control 19 Duplicate Remote Control 21 Cancel『Other』Remote Control 22 Set \ Cancel Preferred Position 23 Operate Preferred Position 24 Quick Command Guide 25 Miscellane
Safety Precautions Before using this product , please read the manual carefully. After reading , please keep this manual properly for future reference. In this manual, the precautions indicated as Warnings and Cautions. Please observe the following precautions to ensure safety. ！ ！ Warning Caution This indicates " Possible death or serious injury This indicates " Possible injury or material damage may occur". may occur ".
Name of Each Part SS40E series Tubular Motor 1 3 4 5 2 1. Driving Wheel： It connects the tubular motor to the aluminum tube so that the motor may drive the aluminum tube to rotate. 2. Code Button： It is for setting the communication code between the remote control unit and the tubular motor. 3. Crown 4. Antenna： It is for receiving instructions from the remote control unit. 5.
ZEN16SA remote control Front side details D E 1 C 2 A 3 B 2 F 4 5 LCD Screen detail 6 1. LCD Screen： 2. 3. 4. 5. 6. A. Group channel : 4 group control channels available from G1 to G4. B. Window channel: 16 window channels available from 1 to 16. C. All: to control all channels at the same time. D. Battery: appears only low battery. E. OK: a confirm key during group control settings. F. Window number frame selection: the currently promoted window number.
Reverse side details 1 2 3 1. Duplicate button： 2. To duplicate or cancel the remote control 3. Mode switch： To switch between USER MODE and SETTING MODE。 4. Battery cover ※Notice: About the remote control: Please do not install the socket at a location that may be exposed to direct sunlight. If the Remote Control activates other electronic appliances, please contact the distributor. Caution: FCC ID: YUYSSRC002 This device complies with part 15 of the FCC Rules.
Installation Installation of motorized blinds： 1. Select a suitable aluminum tube Slot size 5㎜ Cylindrical Aluminum Tube Inside diameterφ40 Molded Aluminum Tube ATD51 A " ring for ATD51" is required 13 ㎜ Molded Aluminum Tube ATD46 Molded Aluminum Tube ATD50 A "plastic ring for ATD50" is required Molded Aluminum Tube ATO43 Specified tube for venetian blinds 2.
3. Position the Crown pin into the slot. Molded Aluminum Tube Cylindrical Aluminum Tube Position for inserting the Positioning Pin of the Crown 4. Fasten the tube at the motor end with screws (not a necessity, may skip this step) Positions for mounting the screws 5. Inset the idler wheel onto tube.
6. Fasten the tube at the idler wheel end with screws (not a necessity, may skip this step). Positions for mounting the screws 7. Install the brackets: Measure a suitable distance for installing the brackets to the target position (in the curtain box or on the wall). 8. Install the motorized blinds: Install the motorized blinds onto the brackets. Notice！The positioning slot should be firmly fixed into the bracket. 9.
Battery installation 2 1. Open the battery cover ＋ /○ －) 2. Insert the battery (notice the polarity ○ 3. Close the battery cover 4. Battery specification: DC 6V (CR2032) 1 ※Notice: About the battery 3 The battery provided with the product is prepared for your initial use. For the battery replacement, please use a battery with the same specifications. If the remote control is not going to be used for a long time, please take the battery out.
Switch Setting Mode / User Mode 1. Please switch the remote control to【Setting Mode】when the motor needs settings, and switch to【User Mode】when the motor is ready to be operated. 2. To switch between【Setting Mode】and【User Mode】should be achieved on the remote control. 3.
4. Mode Switch： Open the battery cover on the remote control. Toggle the【Mode Selection Switch】located above the battery. Note: It is necessary to use a thin rod to toggle the switch. After finish toggling【Mode Selection Switch】, close the battery cover immediately. Schematic Diagram of Mode Selection Switch Setting Mode The switch is at the right position 2. Toggle the Mode Selection Switch User Mode 3. After the mode selection is completed, close the battery cover immediately.
Switch blinds system 1. The tubular motor could operate either【Roller system】or【Venetian system】. 【Roller system】: It could not adjust by degrees on User Mode, but only could on Setting Mode. 【Venetian system】: It could adjust by degrees both on User Mode and Setting Mode. 2. How to switch: Switch the remote control to【Setting Mode】. To enter【Roller system】, press both【UP】&【Enter】for 2 seconds until the cursor [ ] lit.
Set Connection Between Motor and Remote Control 1. Switch the remote control to【Setting Mode】。 2. Channel Selection: Press any button of「」、 「」 、「<」、「>」to select the channel needs to be connected. Press any button of【】、 【】、 【＜】 、【＞】to move cursor [ ] to the target channel 3. Code: To establish a connection between the motor and the remote control. Press【Code】on the motor for 1 second, the motor will respond “beep “. Press the【Code】to start code identification.
Press【Up】and【Down】simultaneously ; when the motor responds with a “beeping” sound, the code identification process is complete and the remote control is ready to control this motor. Beep Press the【Up】 and【Down】 simultaneously ※Notice: Unless it is necessary to establish connection again, please do not press the【Code】 for more than 2 seconds. To avoid interference, please set the connection one by one in the same building. Cancel Connection 1.
Switch Between Forward and Backward 1. Switch the remote control to【Setting Mode】。 2. Switch Between Forward and Backward Rotations： Press【Stop】for 3 seconds; when the motor responds with a “beeping” sound, the process for switching between forward and backward rotation is complete. Beep Press 【Stop】 for 3 seconds. ※Notice: Unless it is necessary to change the rotation direction , please do not press【Stop】for more than 3 seconds.
Set Upper/Lower Limit 1. Switch the remote control to【Setting Mode】。 2. Enter the Upper Limit Setting Mode: Press【Up】and【Stop】simultaneously; when the motor responds with a “beeping” sound, it enters the Upper Limit Setting Mode. Beep Press【Up】and【Stop】 simultaneously. 3. Set the Upper Limit: Use remote control to lift blinds at the target position for setting the upper limit. During this operation, please perform【Switch Between Forward and Backward Rotations】if necessary.
4. Enter the Lower Limit Setting: Press 【Stop】and【Down】simultaneously; when the motor responds with a “beeping” sound, it enters the Lower Limit Setting Mode. Beep Press【Stop】and【Down】 simultaneously 5. Set the Lower Limit: Use remote control to lift blinds at the target position for setting the lower limit. Press【Stop】and【Enter】 simultaneously; when the motor responds with a “beeping” sound, the lower limit setting is complete. Beep Press【Stop】and 【Enter】 simultaneously 6.
Set Group Control 1. Switch the remote control to【User Mode】。 2. Select Group:Press any button of 「」、「」、「<」、「>」to move cursor [ ] to the target group channels G1 ~ G4 which needs to be executed. The ZEN16SA remote control provides up to 4 groups to perform. Select group Press any of them to move cursor Select target group,then the selected group channel is flash. 3. Enter group setting:Press【Enter】for 3 seconds to enter group setting. Enter group setting Press【Enter】 for 3 sec.
4. 5. Select window:Press any button of 「」 、 「」 、 「<」 、 「>」to move cursor [ ] to the target window. Join window: Press【Enter】 to join window in this group and the cursor [ ] will stay on the window once it is joined, another flash cursor [ ] will be stand by after the previous window is joined. Join windows in the group Press【Enter】 to join window in this group. 6.
Duplicate Remote Control This function allows to duplicate codes from a remote control to another without pressing the "Code" button on motor . 1. Switch the original remote control (RM-A) and the duplicate one (RM-B) to 【Setting Mode】。 2. Select the channel needs to be copied on RM-A. 3.
Cancel Other Remote Controls This function works if there are many remote controls connect to one motor, to preserve only one remote control and to cancel the connections between motor and the other remote controls. 1. Switch the preserved remote control to【Setting Mode】。 2. Select the channel needs to be preserved. 3.
Set / Cancel the Preferred Positions 1. Switch the remote control to【User Mode】。 2. Each motor could set 2 preferred positions exclude the upper and lower limit. 3. Set preferred position: Use remote control to lift blinds to target positions. Press【Stop】and【Enter】simultaneously, it is complete when motor responds with beep sound. 4. Cancel preferred position: Use remote control to lift blinds to target preferred positions.
Move to Preferred Position 1. After settings, press【Stop】for 3 seconds to move to preferred positions. 2. Movement is different depends on quantity of preferred position: One preferred position: press【Stop】for 3 seconds the blinds will move to this preferred position.
Command Quick Reference Mode Switch Command Operations Setting Mode Toggle【Mode Selection Switch】to the right Page P11~12 User Mode Toggle【Mode Selection Switch】to the left Setting Mode Operations Page System Switch 1. Roller System: Press【Up】and【Enter】for 2 sec. 2. Venetian System: Press【Down】and【Enter】 for 2 sec. P13 Code Identification 1. Press【Code】button on motor. 2. Press【Up】and【Down】. Cancel Connection Press【Code】for 5 sec.
User Mode Command Set Group Control Set Preferred Position Cancel Preferred Position Move to Preferred Position Operations Page 1. Press【Enter】for 3 sec. to enter group control setting mode 2. Select windows and press【Enter】to join in the group 3. Move to【OK】then press【Enter】to confirm group setting P19~20 Press【Stop】and【Enter】 P23 Press【Stop】and【Enter】 P23 Press【Stop】for 3 sec.
Troubleshooting Conditions Causes Solutions No Power Check the power supply Not connected with remote control Perform the connection again Remote control is running out of energy Replace the battery Remote control is damaged Contact the distributor for service. Motor is damaged Contact the distributor for service.
Illustration of Wiring The color of wires： 1 ：Yellow ○ 2 ：Green ○ 3 ：Red 4 ：Black ○ ○ RJ-14 connector (6P4C) Note： 1 is the internal power source of the motor , do not use it for external power supply. 1.Wire○ ※If any external connection to 27V power source will cause the damage of the motor. 1 and wire○ 2 are connected(short circuited) 1~2 seconds，the motor will turn down. 2.After wire○ 1 and wire○ 4 are connected(short circuited) 1~2 seconds，the motor will turn up. 3.
Appendix Product Specifications： SS40E series Brushless DC Tubular Motor： Power Supply (input)：AC 100~230V；50~60Hz. Operating Voltage：DC 27V. Power Consumption：Rating 29W. Net Weight：1.4 ㎏. Dimensions：660 ㎜（L）× 38 ㎜（Dia.）. Rotation Speed：N6R22－ 22 rpm、N5R27－ 27 rpm、N4R34－ 34 rpm. Torque：N6R22－ 6 N-m、N5R27－ 5 N-m、N4R34－ 4 N-m. Operation conditions: for indoor use only, room temperature 0℃~ 40℃, humidity 60%~90% RH. Storage conditions: to store horizontally in temperature 10℃~ 45℃.
