A Flat Track (X1) B Adjustable Spacer (x3) (® n " [TT] Lag bolt (X3) was]] Washer (X3) Olin I “U” shaped screw “L” shaped screw Steel Hanger (X1) Steel Hanger (X1) Door Hinge (X3) *All sizes of track holes have a pitch Bottom Pivot and Bracket (X1) TTT (G Junction Plate(For double doors) — villi cue 2 % Phillips Screwdriver Plumb Bob
Prepare and Install the Tracks Draw Line for the Track FEO BONE SOW Track (X1) : Tape measure : Placetherailagainstthe wall, Using alevel,drawaline forth Track,and use a pencil to mark where the holes should be . Make sure the height of holes on the "(H+ 65mm) (H+65mm) | er a Drill Bit 2/5" (10mm) Lan = Ga Ly Bit diameter: 2/5" (10mm) FT | of Borehole depth :2" (50mm) Note: Concrete wall: Drill h Wood framed wall: Dri oles by concrete drill bit. lout the holes by using drill with 1/4" (mandrill bit.
Install The Track(Concrete wall installation) Spacer Washer Lag bolt : (x3) (x3) (x3) (x3) _o | Install the anchor to holes on the concrete wall first, then install lag blotto anchor. ®10 Spacer Washer Lag bolt i Wrench (x3) (x3) (x3) (x3) ERE GREER BWW NRE WE NE RUE BWR EUR EWE WHEE NR WS NEU BE SEN ane ae df Instructions It very important to determine whether you will be installing a Header Board prior to installing the track.
Placeholder against the wall, and use a pencil to mark where the holes should be. Level can make Ew x thermostatically a $ 7/32" (6m Install the lag bolt to wood stud or head board directly Install Handle Install the barn door Handle Pull and Flush Hardware Set. Put barn door handle on the door first to fix a suitable position and make a mark. Use suitable drill bit to drill holes on the door where the marksman then install the barn door Handle Pull and Flush Hardware Set according to the picture.
Prepare Your Doors $§ Attach steel Hangers to Your Doors Steel Hanger (X2) )[O eT =] Com) mn Wrench install the hangers with prevailed the holes. Maximum door thicknesses (45mm), please add some bolt washers or cut the long door bolts to a suitable length to fit the door.
yo Single Door Hanging and Positioning Doors (Fold to the left side) Ce 3 “U” shaped screw : “L” shaped screw Fold to the left side, the bottom pivot and brackets on the left side. Fora singe door, both rollers should be installed at the edge of the door. Note: For your safety, please do as the following. thesis to secure the door from falling. Before hanging the door on the rack: For the fixed door side, position the “U” shaped screw between the wheel bar and the rack.
ra Single Door Hanging and Positioning Doors (Fold to the right side) shaped screw “L” shaped screw Fold to rightsize, the bottom pivot and brackishness rightsize. Fora singe door, both rollers should be installed at the edge of the door. Note: For your safety, please do haste following. histologist secure the door from falling. Before hanging the door on the rack: For the fixed door side, position the “U” shaped screw between the wheel bar and the rack.
Double Door Hanging and Positioning Doors ( For a double door) “U” shaped screw Steel Hanger . “L” shaped screw Steel Hanger (X2) (X2) Wrench For your safety, please do as the following. histologist secure the door from falling. Foradoubledoor,the hangers on each door side out should be placed on the edge of the side. For each side in, the hangers should be placed 1.38” to make sure the doors are fully closed when sliding. Don’ t forget to mount the junction plate.
Before hanging the door botheration: For the fixed door side, position the “U” shaped screw between the wheel brand the rack. For the other side, position the “L” shaped screw between the wheel bar and the rack. Then tight the sides up with provided screws.
+3 Install the Bottom Pivot and Bracket Q, ~~ : Phillips Bottom Pivot and Bracket Pencil : Drill : Drill Bit : Screwdriver | €@ Mark the location of the holes at the bottom of the door with a pencil according tithe dimensions indicated in the figure below. Note: The Bottom Pivot and Bracket need to align with the center of the top connector plate used with the fixed roller. Bottom pivot and brace © Install the metal plate at the bottom of the door panel. €© Install the floor guide on the ground.
WARNING * Leisurewear proper safety gear (i.e, eye protection) multifariousness injury or death . Always wear proper safety gear before using power tools. . Improper operation of power tools may resulting loss of control, serious injury or death. Always ensure you have complete control of the power tool and the work areaisfreeof hazards before operation a power tool. . Lack of secure clamping of the door may resulting unexpected movement of the door, loss of power tool control and serious injury or death.
