SSD SATA 5000 2.5" Product Manual Preliminary, Rev 0.7 Document No. 80-11-01488 July 2008 SanDisk Corporation Corporate Headquarters • 601 McCarthy Blvd. • Milpitas, CA 95035 Phone (408) 801-1000 • Fax (408) 801-8657 www.sandisk.
SSD SATA 5000 2.5" Product Manual Rev 0.7 Table of Contents 1. Introduction ................................................................. 4 1.1 1.2 1.3 General Description ....................................................... 4 Key Features ................................................................ 4 Block Diagram .............................................................. 5 2. General Product Specifications ........................................ 6 2.1 2.2 2.3 Interface ...............
SSD SATA 5000 2.5" 7.4 7.5 7.6 Product Manual Rev 0.7 SATA Bridge Support ....................................................14 Interface Connector Drawing .........................................14 Pin Assignment ............................................................15 8. Supported ATA Commands ........................................... 16 8.1 8.2 8.3 8.4 Troubleshooting ...........................................................18 Basic Checks ................................................
SSD SATA 5000 2.5" 1. Introduction 1.1 General Description Product Manual Rev 0.7 SanDisk SSD SATA 5000 2.5" is designed to drive the shift of mobile PC users and blade server users from the hard disk drive to the solid state drive (SSD). A drop-in replacement for the hard disk drive, it delivers far superior durability, performance and power efficiency ─ keeping mobile PCs and blade servers working optimally in the toughest of conditions. SanDisk SSD SATA 5000 2.
SSD SATA 5000 2.5" Product Manual Rev 0.7 o Internal transfer read rate: 68MB/s o Internal transfer write rate: 60MB/s o Random Read (4KB): 4800 IOPS o Average access time: 0.11msec Low power consumption o Supply voltage: 5Vdc o Typical read: 180mA o Typical write: 190mA o Typical idle: 110mA o Typical standby: 70mA Highly reliable o Mean time to failure (MTTF): 2,000,000 hours, based on Part Stress Analysis o Operating shock: 1,500G, 0.5msec half sine o Operating vibration: 16.
SSD SATA 5000 2.5" Product Manual Rev 0.7 2. General Product Specifications 2.1 Interface The SSD interface complies with the following standards: SATA 1.0a Gen1i (1.5Gb/s) SATA 2.5 ATA-7 The SSD supports Serial ATA 1.5Gbps (150MB/sec) interface rate. 2.2 Capacity This datasheet refer to the 8, 16, 32, 64GB version. Table 1: SanDisk SSD SATA 5000 2.
SSD SATA 5000 2.5" Product Manual Rev 0.7 3. Power Characteristics 3.1 Supply Voltage Table 3: SanDisk SSD SATA 5000 2.5” Supply Voltage Parameter 3.2 Specifications Input Voltage 5V ± 5% Maximum Ripple 100mV (peak to peak), 0 – 30MHz Supply Rise Time 7 msec to 100 msec Maximum Supply Fall Time 5 sec Power Consumption Table 4: SanDisk SSD SATA 5000 2.5” Power Consumption Parameter 3.3 Specifications (W) Maximum 1.1 Read (Typical) 0.9 Write (Typical) 0.95 Active Idle (Typical) 0.
SSD SATA 5000 2.5" Product Manual Rev 0.7 4. Physical Characteristics 4.1 Mechanical Table 6: SanDisk SSD SATA 5000 2.5” Mechanical Dimensions and Weight Parameter Specifications Width 69.85 ± 0.25 mm Height 9.5 ± 0.2 mm Length 102.0 ± 0.25 mm Maximum Weight 4.2 96 gr Mounting Instructions Before unpacking and installing the drive, take anti-static measures in order to avoid damage to the drive. The drive may be exposed to potential handling and electrostatic discharge (ESD) hazards.
SSD SATA 5000 2.5" 4.3 Product Manual Rev 0.7 Installation Orientation The SSD can be installed in all axes (6 directions). For a mechanical drawing, see Figure 2. Figure 2: SanDisk SSD SATA 5000 2.5” Mechanical Drawing © 2008 SanDisk® Corporation 9 July 2008, Document No.
SSD SATA 5000 2.5" Product Manual Rev 0.7 5. Environmental Specifications 5.1 Temperature Table 7: SanDisk SSD SATA 5000 2.5” Temperature Support Parameter Specifications Operating: Commercial Version 0°C to 70°C Enhanced Version 5.2 -25°C to 75°C Non-operating -55°C to 95°C Storage -55°C to 95°C Maximum temperature gradient 30°C per hour Humidity Table 8: SanDisk SSD SATA 5000 2.
SSD SATA 5000 2.5" 5.5 Product Manual Rev 0.7 Altitude Table 11: SanDisk SSD SATA 5000 2.5” Altitude Support Parameter Specifications Operating -400m to 24,384m (-1,312ft. to 80,000ft.) Non-operating -400m to 24,384m (-1,312ft. to 80,000ft.) 5.6 Acoustics The SSD does not generate any acoustic noise (0dB). 5.7 Regulations The SSD is certified with the following standards. Table 12: SanDisk SSD SATA 5000 2.
SSD SATA 5000 2.5" 5.7.1 Product Manual Rev 0.7 EMC Directive 73/23/ECC for product safety Directive 89/336/EEC: Table 13: SanDisk SSD SATA 5000 2.5” Electromagnetic Compatibility Support Parameter Emission Standard EN55022:1998, A1:2000,A2:2003 IEC 61000-3-3 Immunity EN55024:1998, A1:2001, A2:2003 IEC 61000-4-2 IEC 61000-4-3 IEC 61000-4-4 IEC 61000-4-5 IEC 61000-4-6 IEC 61000-4-8 IEC 61000-4-11 5.7.2 FCC FCC 47CFR part 15 subpart B class B. 5.
SSD SATA 5000 2.5" Product Manual Rev 0.7 6. Reliability Characteristics 6.1 Error Rate The non-recoverable error rate is 1 error per 1014 bits read. 6.
SSD SATA 5000 2.5" Product Manual Rev 0.7 7. Interface 7.1 Supported Standards The SSD complies with the following standards: ATA/ATAPI-7: ANSI INCITS 397-2005, AT Attachment with Packet Interface-7. Serial ATA Revision 2.5 Specification (Ratification Date: October 27, 2005). 7.2 Interface Connector Characteristics Table 15: SanDisk SSD SATA 5000 2.
SSD SATA 5000 2.5" 7.6 Product Manual Rev 0.7 Pin Assignment Table 16: SanDisk SSD SATA 5000 2.5” Pin Assignment Power Segment Signal Segment Pin Function Description nd S1 Ground 2 mate S2 A+ S3 A- S4 Ground S5 B- S6 B+ S7 Ground 2nd mate P1 V33 3.3V Power P2 V33 3.3V Power P3 V33 3.
SSD SATA 5000 2.5" 8. Product Manual Rev 0.
SSD SATA 5000 2.5" Product Manual Rev 0.7 Disable write cache 82h Disable Advanced Power Management 85h Enable SATA Feature- software Setting Preservation 90h Enable look-ahead AAh Disable automatic acoustic management C2h Enable reverting to power-on defaults CCh S.M.A.R.T Read Data B0h/D0h S.M.A.R.T Read Attribute Thresholds B0h/D1h S.M.A.R.T Enable Disable Attribute Autosave B0h /D2h S.M.A.R.T Save Attribute Values B0h /D3h S.M.A.R.T Execute Offline Immediate B0h /D4h S.M.A.R.
SSD SATA 5000 2.5" 8.1 Troubleshooting 8.2 Basic Checks Product Manual Rev 0.7 Most disk problems are caused by improper disk installation. If a problem arises, the following should be checked: Cable: o Improper cable has been used o Cables are too long to support the transfer rate o Improper cable connection to the device Device connector: Improperly locked Power supply: Below SSD requirements 8.3 BIOS Setup Verify that the disk is enabled in the BIOS.
SSD SATA 5000 2.5" 9. Product Manual Rev 0.7 Ordering Information Table 17: SanDisk SSD SATA 5000 2.5” Ordering Information SDIGF-CCCU-XXXXGY SD I SanDisk Interface: S – SATA G Generation: 5 – 5000 (5th) F Form factor: C – 2.5" (9.5mm) CCC Capacity (GB): 008 016 032 064 U Units: G (GB) XXXX Customer code reference G Component generation 0 – Initial generation, Commercial Temperature.
SSD SATA 5000 2.5" Product Manual Rev 0.7 SanDisk® Corporation general policy does not recommend the use of its products in life support applications where in a failure or malfunction of the product may directly threaten life or injury. Per SanDisk Terms and Conditions of Sale, the user of SanDisk products in life support applications assumes all risk of such use and indemnifies SanDisk against all damages. See “Disclaimer of Liability.
