DT-220V Operating instruction Instruccions de manejo GB E
1
2
Controls 1 3 5 6 7 9 11 13 14 16 17 18 19 2 Display Telescopic Aerial 4 Display button Preset 6-10 Stereo/Mono/Alarm button Band/Time set button 8 Light button Power button 10 Preset 1-5 Tuning up/down button 12 Volume Control Lock switch Loudspeaker/Headphone switch 15 DC input socket Headphone socket Auto wind earphones Auto wind earphones switch Battery compartment RESET GB Display A B C D E F G H I J Waveband and A.M./P.M.
Installing batteries 1. position the radio face down. 2. Press the catch and slide in the direction of the arrow. 3. Lift up the battery cover. 4. Insert 2xUM-3 (AA) size batteries. Make sure the batteries are positioned in accordance with the diagram indicated. 5. Replace the battery cover. Battery replacement The battery indicator will appear and flash in the display when the batteries are in need of replacement .
Setting the alarm time 1. Ensure that the radio is switched off. 2. Press and hold down the Alarm button for more than 2 seconds until the hours digit and alarm symbol begin to flash in the display . 3. Whilst the hours digit is flashing, adjust the hours using the Tuning Up/Down buttons. 4. Press the Alarm button, the minute digit begins to flash in the display. 5. Whilst the minute digit is flashing, adjust the minutes using the Tuning Up/Down button. 6.
Operating the radio-search tuning 1. Switch on your radio by pressing the Power Button. Note: The radio is originally set to be 90 minutes auto shut off after Power is switched on ( symbol will appear on the display). If you don’t need this feature, press Power button for more than 2 seconds until symbol removed from the display . 2. Select the required waveband by repeatedly pressing the Band button. On FM and TV bands, fully extend the Telescopic aerial.
Operating the radio – manual tuning 1. Switch on your radio by pressing the Power button. 2. Select the desired waveband using the Band button. The waveband selected will appear in the display. On FM/TV bands, fully extend the Telescopic aerial. On AM (MW) band, rotate your radio for best reception. 3. A single press on either the Tuning Up/Down will change the frequency up or down. Adjust the GB Volume control to the required level.
Presetting stations You may store up to 10 stations each on FM, AM (MW) and TV bands giving a total of 30 preset stations. 1. Tune into the required stations using one of the tuning methods previously described . 2. To store the station, press and hold down one of the PRESET button 1-5 for more than 2 seconds until display shows preset location. 3.
Display backlight Pressing the Light button will switch on the display backlight and illuminate the display for approximately 7 seconds. Lock switch The lock switch located on the right side of your radio is used to prevent unintentional operation. 1. Slide the Lock switch to the up ‘ locked ‘ position, GB the symbol will appear in the display. The Power and all other buttons will be disabled except the Light button . This will prevent accidental operation when the radio is packed in a suitcase.
Headphone socket In addition to the built in earphones, your radio is provided with a headphone socket. This allows you to use different types of ear or headphones with your radio. 1. To use external headphones, slide the Loudspeaker/Headphone switch to the position and plug the headphones into the headphone socket. 2. Slide the Loudspeaker/Headphone switch to the position to return to normal operation.
Troubleshooting/Reset button If your radio fails to operate correctly or some digits on the display are missing or incomplete, carry out the following procedures. 1. Switch off the radio and remove the batteries. 2. With the aid of a suitable implement (the end of a paper clip), press the RESET button located on the underside for at least 2 seconds, this will reset the microprocessor but still keep the clock time and all stations stored in preset memory.
12
Controles 1 2 Pantalla Antena telescó pica Presintoní as 6-10 4 Botó n Pantalla 5 Botó n de esté reo/mono/alarma 6 Botó n de selecció n de banda/hora 7 Botó n de encendido 8 Botó n de luz 9 Botó n de sintonizació n ascendente/descendente 10 Presintoní as 1-5 11 Interruptor de bloqueo 12 Control de volumen 13 Interruptor de altavoz/auriculares 14 Conexió n para auriculares 15 Conexió n para la alimentació n de CC 16 Auriculares autorrebobinables 17 Interruptor de rebobinado automático de auriculares 18 Comp
Instalació n de las pilas 1. Coloque la radio hacia abajo. 2. Pulse el pestillo y deslí celo en la direcció n que marca la flecha. 3. Levante la tapa del compartimento de pilas. 4. Inserte 2 pilas tipo UM-3 (AA). Compruebe que las pilas están colocadas de acuerdo con el diagrama indicado. 5. Vuelva a colocar la tapa del compartimento de pilas. Sustitució n de las pilas Aparecerá en la pantalla el indicador de nivel de la pila y parpadeará cuando sea necesario cambiarlas.
Configuració n de la hora El reloj se pondrá en marcha al instalar las pilas. Cuando se instalen por primera vez, la pantalla mostrará 0:00. Nota: La hora só lo se puede configurar con la radio apagada. 1. Compruebe que la radio está apagada. 2. Pulse y mantenga pulsado el botó n Time Set durante más de 2 segundos hasta que el dí gito de las horas empiece a parpadear en la pantalla. 3. Mientras parpadea, ajuste las horas usando los botones Tuning Up/Down. E 4.
Configuració n de la hora de la alarma 1. Compruebe que la radio está apagada. 2. Pulse y mantenga pulsado el botó n Alarm durante más de 2 segundos hasta que el dí gito de las horas y el sí mbolo de la alarma empiecen a parpadear en la pantalla. 3. Mientras parpadea, ajuste las horas usando los botones Tuning Up/Down. 4. Pulse el botó n Alarm; el dí gito de los minutos empezará a parpadear en la pantalla. 5. Mientras parpadea, ajuste los minutos usando el botó n Tuning Up/Down. 6.
Funcionamiento de la radio: sintonizació n por bú squeda 1. Encienda la radio pulsando el botó n Power. Nota: La radio está configurada de fábrica para apagarse automáticamente a los 90 minutos despué s de encenderla (aparecerá el sí mbolo en la pantalla). Si no quiere hacer uso de esta funció n, pulse el botó n Power durante más de 2 segundos hasta que desaparezca dicho sí mbolo . E 2. Seleccione la banda que desee pulsando repetidamente el botó n Band.
Funcionamiento de la radio: sintonizació n manual 1. Encienda la radio pulsando el botó n Power. 2. Seleccione la banda que desee pulsando el botó n Band. Se mostrará en la pantalla la banda seleccionada. En las bandas de FM y TV, extienda completamente la antena telescó pica. En las bandas de AM (MW), gire la radio hasta obtener la recepció n más ó ptima. 3. Una pulsació n en Tuning Up o Down cambiará la frecuencia un salto hacia arriba o hacia abajo.
Salto de sintonizació n de AM(MW) En Europa y otras partes del mundo, los saltos de sintonizació n de la banda de AM (MW) son de 9 kHz, en Amé rica, son de 10 kHz. Para cambiar el salto de sintonizació n de AM de 10 kHz a 9 kHz, haga lo siguiente: 1. Encienda la radio y seleccione la banda de AM (MW). 2. Apague la radio. 3. Pulse sucesivamente los botones Tuning Down y Power, la radio cambiará el salto de sintonizació E n a 9 kHz en la banda de AM.
Presintonizació n de emisoras Puede almacenar hasta 10 emisoras por cada banda: FM, AM (MW) y TV, lo que hace un total de 30 emisoras presintonizadas. 1. Sintonice las estaciones que desee utilizando uno de los mé todos descritos anteriormente. 2. Para almacenar la emisora, pulse y mantenga pulsado uno de los botones PRESET 1-5 durante más de 2 segundos hasta que aparezca en la pantalla la posició n de memoria correspondiente. 3.
Modos de presentació n Con la radio encendida, pulse el botó n Display para cambiar entre frecuencia y hora normal. Luz de fondo de la pantalla Al pulsar el botó n Light se encenderá la luz de fondo de la pantalla y é sta se encenderá durante unos 7 segundos. Interruptor de bloqueo El interruptor de bloqueo situado en el lado derecho E de la radio se utiliza para evitar un funcionamiento no deseado de la radio. 1.
Auriculares Los auriculares acoplados a la radio disponen de un sistema de rebobinado automático para facilitar su almacenamiento. 1. Tire suavemente de ellos desde el lado derecho de la radio. 2. Deslice el interruptor Loudspeaker/Headphone hasta la posició n ; se silenciará el altavoz. 3. Para retraerlos, deslice el interruptor situado en la parte posterior de la caja. Manté ngalo deslizado mientras se rebobinan en el interior de la caja. 4.
Adaptador de CA (no incluido) El adaptador de CA para usar con esta radio debe suministrar 3 V de CC y 200 mA en la patilla central del negativo. Inserte el enchufe del adaptador en la toma de CC situada en el lado izquierdo de la radio. Enchufe el adaptador en la toma de electricidad. Cuando use el adaptador, las pilas se desconectarán automáticamente. El adaptador de CA debe desconectarse de la toma de corriente y de la radio cuando no se use. E Botó n Mono 1.
Solució n de problemas, botó n de reinicio Si la radio no funciona correctamente o faltan, o aparecen incompletes, algunos dí gitos en la pantalla, realice los siguientes procedimientos: 1. Apague la radio y saque las pilas. 2.
381H512