1 5 3 2 4 6 11 7 12 13 14 8 9 10 2
Location Of Controls Welcome to SANGEAN World of Listening. To ensure proper operation please familianrize yourself with These instructions before using your new receiver.
B A D C E F I J 1 2 3 G 4 5 H 4 6 7 8 9 K L
Display Icons Band Selected/ PM---------------------------------------------------------- A Timer / (Alarm)--------------------------------------------------------------B FM Stereo lndicator---------------------------------------------------------C System Lock-----------------------------------------------------------------D Low Battery---------------------------------------------------------------- - E Standby Set------------------------------------------------------------------F Time /Frequency-----------
Battery Installation The battery cover is located on the back of the unit. Slide the cover in the direction of the arrow to gain access to the battery compartment 10 insert 2 AAA(UM-4) batteries into the compartment.Make sure that batteries are positioned in accordance with the diagram located below batteries in battery compartment. Replace cover. Note: [1] A low battery icon E appearing on the LCD display indicates a weak and replacement is necessary.
Setting Time When batteries are installed for the first time the LCD display time digit will flash indicating that the time needs to be set. The clock can be set with the power off but the lockswitch 3 must be off. To set time press Time Set Button 8 for more then 2 seconds until hour digit flashes. While hour digit is flashing use Time Adjust Buttons 13 and 14 to select the correct hour. Pressing Time Set Button 8 again will cause the minite digit to flash. Use same procedure as hour set to set minite set.
LCD will return to real time and Standby Set icon F will appear in display . A buzzer will sound when set time is reached and will continue for at least 3 mimutes or until it is stopped by pressing the Power On/Off Button. Short Term Alarm Set This receiver is equipped with a short term 1-180minute timer.To set timer Press the Alarm Set Button 9 for more than 2 seconds until LCD alarm set icons B appears time digit flashes.During flashing press Time Adjust Button 13 14 to adjust to desired time .
RADIO OPERATION Antenna/Earphone Use The earphone cord acts as an antenna during reception of FM/TV/Weather Band(DT-300/300V/300VW)channels and should be extended as much as possible to improve sensitivity. Insert the earphone into the earphone jack 6 for earphone operation . When listening with the built-in speaker the enclosed pig tail trailing antenna should be inserted into the earphone jack which will provide antenna function.
Volume Control The volume may be adjusted by using the Volume Control Adjustment 1 Tuning the Radio Band Frequency AM 520-1710kHz/ 522-1629kHz Antenna Internal-Rotate radio for best reception FM 87.5-108MHz External-Make sure earphone or pig tail antenna is inserted into earphone jack. TV CH.2-13(VHF) External-Make sure earphone or (DT-300V/DT-300VW) pigtail antenna is inserted into earphone jack.
WX CH.0-9 External-Make sure earphone or pigtail antenna is inserted into Earphone jack A.Scan Tuning Turn on the radio by pressing On/Off Button 5 . Select the desired band by pressing Band Selection Button 8 Press and hold the Tuning Control Button 13 or 14 for more than 1/2 second . The radio will start to scan and will stop at the first active station. Repeating the procedure will start the scan again.
until the desired station is reached or pressing and holding the Tuning Control 13 or 14 until the station is reached. C. Setting Presets Manually Turn on receiver by pressing On/Off Button 5 .Select desired band by pressing Band Selector Button 8 .Tune to the desired station using the Manual or Scan Tuning Method as described above. When the desired station is reached press Memory Button 11 . "Memo" flashes in the LCD display and a suggested preset position flashes.
station is selected to take its place. When the memory is full for a particular band pressing the Memory Selection Button 11 will cause all the positions to flash. In this case,select the desired position. press the Memory Selection Switch 11 and the original station will be eliminated and the new station will take its place. D.Selecting Memory Presets Turn on receiver by pressing On/Off Button 5 .
On/off Button 5 .Select desired band by pressing Band Select or Button 8 . Press Memory Button 11 . Memo will flash in display. Press Select Button 12 for move than 2 seconds until auto/memo appears and flashes in display. press memory Button 11 again. The receiver will automatically begin to scan and set memory preset positions. It will dliminate any memory presets already with in the band. F.Memory Scan Play Turn on receiver by pressing On/Off Buttons 5 .
Note: If the Select Cursor L points at the frequency the Tuning Control Up/Down Button 13 14 will continue to change frequency within the band selected. If the Selector Cursor L points at the position digits for the memory presets H the Tuning Control Up/Down Button 13 and 14 will select the memory presets. 14 G.Deleting Memory Positions If The memory is full or you would like to delete a memoey position select the preset youy would like to delete.
Mono/Stereo Button Monaural or Stereo headphone reception may be selected durning FM reception by alternately pressing the Mono/Stereo Button 9 The Speaker On/OffSwitch 7 must be in the Off Lock Switch To Prevent accidental changing of any of the radio settings move the Look Switch 3 to the locked position. When engaged in the locked position the icon key D will appear in the LCD display. To release the lock switch simply move the switch to the off position.
Specification Type: FM- Stereo (Via earphone) AM- Standard (mono) TV Band (Mono Ch,2-13 VHF) DT-300V/VW Weather Band (WX) (Mono Ch. 0-9) DT-300VW Earphone jack: 3.5 mm mini-plug 16 or 32 ohm impedance (Stereo) Output Power: 50 mW (10 THD) via built-in speaker Speaker: 1.1inch diameter,4ohm impedance Batteries: 3 volt(AAA/UM-4 size) x 2 Dimension (WxHxD):2 1/4" X 3 3/4" X3/4" Weight: 3.
