PR-D2/V Operating instruction GB Instruccions de manejo E WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION THE LIGHTNING FLASH AND ARROWHEAD WITHIN THE TRIANGLE IS A WARNING SIGN ALERTING YOU OF “DANGEROUS VOLTAGE” INSIDE THE RADIO. RISK OF ELECTRIC SHOCK DO NOT OPEN ! CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE BACK, NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Important safety instructions 1. Read and understand all safety and operating instructions before the radio is operated. 2. Retain instruction: The safety and operating instructions should be retained for future reference. 3. Heed warnings. All warnings on the appliance and operating instructions should be followed. 4. Follow all operations and use instructions. 5. Water and Moisture: The appliance should not be used near water.
only the correct type of power source indicated. If you are not sure of the type of power supply to your home, consult your dealer or local power company. 11. Do not overload wall outlets or extension cords. This can result in a risk of fire or electrical shock. Never insert objects of any kind into the radio through opening. GB The objects may touch dangerous voltage points or short out parts. This could cause a fire or electrical shock. 12.
3
Control Locations 1. Headphone socket 2. Tone control 3. Volume control 4. Rotary Tuning Control 5. Display 6. Manual/Auto Tuning UP/Down control 7. Multi-functional button- Band/Time set/Stereo-Mono selection 8. Light button 9. POWER/SLEEP button 10. Telescopic Aerial 11. Preset buttons (also multi-functional buttons for D.S.T.,tuning step and alarm set ) 12. Carrying handle 13. AC socket 14. Speaker 15. Battery compartment 16. External AM antenna socket (for PR-D2V only) 17.
Battery operation 1. Remove the battery cover on the rear of the unit by pushing the catches in the direction of the arrows. 2. Insert four UM-1 (D size) batteries into the space in the compartment. Take care to ensure all batteries are inserted with the correct polarity as shown inside the battery compartment. Replace the battery cover. 3. Reduced power, distortion and a ‘stuttering’ sound are all signs that the batteries may need replacing. 4.
Setting the clock 1. The clock will start running when the batteries are installed or when the radio is connected to the mains supply. The display will show 0:00 (PR-D2) or 12:00 (PR-D2V). 2. Ensure that the radio switched off. 3. Press the Band (Time Set/ST. MO.) button, the hours digits will flash in the display followed by a beep sound. 4. Press Tuning up/down button to set the required hours. 5. Press the Time Set button, the minute digits will flash in the display. 6.
Manual tuning 1. Press the Power button to turn on the radio. 2. Select the required waveband by repeatedly pressing the Band button. For the FM/TV (PR-D2V) band fully extend the Telescopic aerial and set it at an angle of 45 degrees. 3. A single press on either the Tuning up or Tuning down buttons will change the frequency in the following increments: FM 50 or 100 kHz (PD-D2), 100 kHz or 200 kHz (PR-D2V) MW 9 kHz or 10 kHz (PR-D2V) TV 1 channel (PR-D2V) 4.
Storing stations in preset memories There are 5 memory presets for each waveband. 1. Press the Power button to turn on the radio. 2. Tune to the required station using one of the methods previously described . 3. Press and hold down the required preset for until the radio beeps (greater than 2 seconds). The preset number will appear in the display and the station will be stored under the chosen GB preset button. 4. Repeat this procedure for the remaining presets. 5.
Setting the HWS (Humane Wake System) alarm A beep tone will sound when using the HWS alarm. The alarm beep will increase in volume every 15 seconds for one minute followed by one minute silence before repeating the cycle. The HWS alarm will sound for one hour unless turned off by pressing the Power button. Pressing the Power button whilst the alarm is sounding will cancel the alarm for 24 hours. 1. The HWS alarm can be set with the radio switched off. 2. Press the HWS alarm button (Preset no.
Sleep function The sleep timer will automatically switch off the radio after a preset time has elapsed. 1. Press and continue to hold down the Power button for more than 2 seconds, followed by 2 beep tones, the display will cycle through the available sleep times in the order 90-60-30-15-90. GB Release the Power button when the required sleep time appears in the display. The symbol will appear in the display and the radio will play the last station selected. 2.
Setting tuning step Tuning steps on some countries are different from where you purchase the radio. If you buy the radio in Europe and intend to use it in Northern America or some Southern American countries, you may have to adjust tuning step so the radio may continue to serve you well. While radio is switched off, press Preset 3 button (Step) for more than 7 seconds until display FM and 100 kHz (tuning step) are flashing followed by a beep tone.
Stereo/Mono button The radio is designed to receive FM stereo broadcasting with headphones connected to the headphones socket. If the reception is weak, continue pressing Band (Time Set. ST/MO ) button for more than 2 seconds to change from Stereo to Mono. In display, stereo indicator will disappear. GB External AM antenna socket (PR-D2V only) Connect your outdoors AM antenna to improve the AM band reception.
Circuit Features Loudspeaker 5 inches 4 ohm, 1 1/2 inches tweeter 4 ohm. Output Power Mains 1.4 Watts Batteries 0.8 Watts Headphone socket 3.5 mm dia.
14
Instrucciones importantes sobre seguridad 1. Lea y comprenda todas las instrucciones de seguridad y funcionamiento antes de poner en funcionamiento la radio. 2. Conserve las instrucciones: Conserve las instrucciones de seguridad y funcionamiento para futuras consultas. 3. Cumpla las advertencias. Siga puntualmente todas las advertencias e instrucciones de funcionamiento del aparato. 4. Siga todas las operaciones e instrucciones de uso. 5.
9. Fuentes de alimentació n: La radio só lo debe conectarse al tipo de fuente de alimentació n indicada en la etiqueta de marca. Si no está seguro del tipo de fuente de alimentació n de su domicilio, consulte al vendedor o a la compañ í a de suministro elé ctrico. 10. Cables de alimentació n elé ctrica: El cable de alimentació n elé ctrica debe colocarse de modo que nadie pase por encima, E ni quede pellizcado; tampoco deje ningún elemento sobre é l.
13. Si no va a utilizar la radio durante un perí odo de tiempo prolongado, quite las pilas. Podrí an tener una fuga y dañ ar el mueble o la propia radio. 14. No intente reparar usted mismo el receptor. Si desmonta la cubierta podrí a verse expuesto a un voltaje peligroso e invalidar la garantí a. Todas las reparaciones deberán ser realizadas por el servicio té cnico autorizado. 15.
Lugares de control 1. Toma de los auriculares 2. Control de tono 3. Control de volumen 4. Control giratorio de sintonizació n 5. Pantalla 6. Control manual/automático de sintonizació n hacia arriba y hacia abajo 7. Botó n multifunció n: selecció n de banda/hora/esté reo-mono 8. Botó n de luz 9. Botó n POWER/SLEEP(encendido/temporizador) 10. Antena telescó pica 11. Botones de presintonizació n(tambié n botones multifunció n para la funció n de ahorro de energí a, saltos de sintonizació n y alarma) 12.
Manejo de las pilas 1. Quite la cubierta del compartimento de las pilas situado en la parte posterior de la unidad presionando sobre las presas en la direcció n de las flechas. 2. Inserte cuatro pilas de tipo UM-1(tamañ o D)en su lugar correspondiente del compartimento. Compruebe que las pilas están insertadas según la polaridad indicada en el interior del compartimento. Vuelva a colocar la cubierta de las pilas. 3.
Funcionamiento con la red elé ctrica Coloque la radio sobre una superficie plana. Conecte el enchufe a la toma situada en la parte posterior de la radio, comprobando que está completamente encastrado en la toma. Las pilas se desconectarán de forma automática. El cable de CA debe estar desconectado de la toma de red cuando no vaya a usarse durante un perí odo prolongado de tiempo. E Ajuste del reloj 1.
Sintonizació n por exploració n 1. Pulse el botó n Power para encender la radio. 2. Seleccione la banda de frecuencias que desee pulsando repetidamente el botó n Band. Para la banda FM/TV (PR-D2V), extienda por completo la antena telescó pica y coló quela en un ángulo de 45 grados. 3. Pulse y mantenga pulsado el botó n Tuning up o Tuning down durante más de 0,5 segundos para iniciar la sintonizació n por exploració n. 4.
Sintonizació n manual 1. Pulse el botó n Power para encender la radio. 2. Seleccione la banda de frecuencia que desee pulsando repetidamente el botó n Band. Para la banda FM/TV (PR-D2V), extienda por completo la antena telescó pica y coló quela en un ángulo de 45 grados. 3. Una pulsació n sobre el botó n Tuning up o Tuning down cambiará la frecuencia en los siguientes incrementos: E FM 50 ó 100 kHz (PD-D2),100 kHz ó 200 kHz (PR-D2V) MW 9 kHz ó 10 kHz (PR-D2V) TV 1 canal (PR-D2V) 4.
Sintonizació n mediante el control giratorio 1. Pulse el botó n Power para encender la radio 2. Seleccione la banda de frecuencia que desee pulsando repetidamente el botó n Band. Para la banda FM/TV (PR-D2V), extienda por completo la antena telescó pica y coló quela en un ángulo de 45 grados. 3. Gire el control Tuning para cambiar la frecuencia en los siguientes incrementos: FM 50 kHz MW 1 kHz TV 1 canal (PR-D2V) 4.
Escucha de las emisoras presintonizadas en la memoria 1. Pulse el botó n Power para encender la radio. 2. Seleccione la banda de frecuencia que desee pulsando repetidamente el botó n de banda. 3. Pulse momentáneamente el botó n Preset; aparecerán en la pantalla el número de memoria y la frecuencia de la emisora. Ajuste de la alarma de la radio E Cuando se selecciona la alarma de la radio, é sta se encenderá y emitirá la última emisora escuchada.
Establecimiento de la alarma HWS (sistema de despertador humano) Cuando use la alarma HWS, la radio emitirá un sonido bip. El volumen de este sonido irá en aumento cada 15 segundos durante un minuto, seguido por un minuto de silencio antes de repetir este ciclo. La alarma HWS sonará durante una hora salvo que se apague antes pulsando el botó n Power. Si se pulsa el botó n Power mientras está sonando la alarma la cancelará durante 24 horas. 1. La alarma HWS se puede establecer con la radio apagada. 2.
Funció n de temporizador El temporizador de sueñ o desconectará automáticamente la radio transcurrido un perí odo de tiempo preestablecido. 1. Pulse y mantenga pulsado el botó n Power durante más de 2 segundos, hasta que escuche dos bip; la pantalla pasará cí clicamente por los tiempos de temporizació n disponibles en el siguiente orden: 90-60-30-15-90. Suelte el botó n Power cuando aparezca en pantalla el tiempo de temporizació n E requerido.
Ajuste del salto de sintonizació n Los saltos de sintonizació n en determinados paí ses son distintos de los del lugar en donde adquirió la radio. Si la compró en Europa e intenta usarla en Norteamé rica o en algunos paí ses de Sudamé rica, tal vez tenga que ajustar la sintonizació n de modo que pueda seguir utilizándola. Con la radio apagada, pulse el botó n Preset 3 (Paso) durante más de 7 segundos hasta que FM y 100 kHz (sintonizació n) parpadeen y suene un bip.
Toma para auriculares La radio dispone de una toma para auriculares de 3,5 mm situada en el lado derecho, detrás del botó n Tone control. Si se inserta un conector se enmudece automáticamente el altavoz interno. Botó n Stereo/Mono La radio puede recibir emisoras de FM en esté reo con auriculares conectados a su correspondiente toma. Si la recepció n es dé bil, E siga pulsando el botó n Band (Time Set . ST/MO ) durante más de 2 segundos para cambiar de esté reo (Stereo) a monoaural (Mono).
Especificaciones Alimentació n elé ctrica Red 230 V CA (o 110 V para la PR-D2V) Pilas 4 X UM-1 (tamañ o D) Rango de frecuencias FM 87.50 - 108 MHz MW 522 - 1710 kHz (salto de sintonizació n de 10 kHz) 522 - 1629 kHz (salto de sintonizació n de 9 kHz) TV Canal 2 - 13 (só lo el PR-D2V) Caracterí sticas del circuito Altavoz 5 pulgadas 4 ohm, 1 1/2 pulgadas trenzado 4 ohm Salida de potencia de la red 1,4 W Pilas 0,8 W Toma de los auriculares Sistema de antena 3,5 mm diám.
381G712