ATS-405 中文 GB Version 1
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. GB 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13.
15. To Reduce the Risk of Fire or Electric Shock, Do not Expose This Appliance To Rain or Moisture. GB 16. The Shock Hazard Marking and Associated Graphical Symbol is provided on the rear of unit. 17. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, shall be placed on the apparatus. 18. Excessive sound pressure on ear-and headphones could impair the hearing ability.
21. The batteries shall not be exposed to excessive heat such as sunshine, fire or the like. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device. CAUTION: These servicing instructions are for use by qualified service personnel only.
Introduction The Sangean ATS-405 world band digital tuning receiver provides the following range of features: Professional digital multi-band world receiver Full shortwave 14 meter bands Five tuning methods-direct frequency access, auto scan, manual tuning, memory recall and rotary tuning ATS (Auto Tuning System)-auto scan and preset stations Shortwave meter band selection 148 station presets 2 alarm timers by buzzer and radio Real time clock Adjustable sleep timer Tone control (Music/Normal/News) 1 kHz fin
Controls Display backlight illumination 2 Loudspeaker 3 LCD display 4 Preset 1 and Squelch button 5 Preset 2 and Tuning mute button 6 Preset 5 and tuning step selection button 7 Preset 3 and software mute button 8 Charging indicator 9 Power and sleep timer button 10 Band width adjustment and buzzer alarm setting button 11 Local/DX selection and radio alarm setting button 12 Display button 13 Menu and Fine tune button 14 Preset 6 and AGC control button 15 16 Tuning Up/Down control button 17 Preset 9 and disp
Preset 4 and MW tuning step selection 26 Radio button selection 27 FM stereo/mono selection 28 Headphone socket 29 AC IN socket of supplied power adapter 30 Tone control (News/Normal/Music) 31 Volume control 25 GB
Controls Charge On/Off selection Lock switch 34 Foldable stand 35 Telescopic antenna 36 Battery compartment 37 RESET 32 33 LCD display Icons A B C D E F G H I J K L M N O P Q R S T Battery power indicator RDS clock time Fine tune status Sleep timer and snooze Auto Tuning System (ATS) execution HWS Buzzer wake up Radio wake up Shortwave meter band Squelch ON Signal level Key locked Soft Mute status Menu Frequency unit DX/Local status Band width Memory page selection Frequency and Time display Radio band
GB
Power Supply The ATS-405 operates on 4 x UM-3 (AA Size, LR6) batteries also powered by external AC power adapter of 7.5V/0.75A (supplied) or external DC power adapter of 7.5V/0.75A with center pin positive for China and Taiwan (supplied). Press and remove battery cover in the direction indicated by the arrow on the cover. Insert 4 x UM-3 (AA size, LR6) batteries with polarity shown on the radio cabinet. Slide battery cover back into place in direction of arrow until case snaps into place.
Battery operation using rechargeable batteries GB 1. Remove the battery cover on the back of the unit by sliding the cover in the direction of the arrow. 2. Slide the CHARGE switch located in the bottom side of radio to ON position. 3. Insert four Rechargeable UM-3 (AA size, LR6) batteries into the battery compartment. Take care to ensure all batteries are inserted with the correct polarity as shown on the back of the radio.
Batteries will only be charged when the radio is switched off and connected to the AC adaptor. IF the radio is not to be used for any extended period of time it is recommended that the batteries are removed from the radio. The batteries should not be exposed to excessive heat such as sunshine, fire or the like. After use, disposable batteries should if possible be taken to a suitable recycling centre.
Battery operation using non-rechargeable batteries GB If you use non-rechargeable batteries, before replacing the batteries make sure the CHARGE switch located in the bottom side of radio to OFF position and follow above instructions to install and replace batteries. Setting clock time 1. When the radio is switched off, press and release Time set button 18, display will show -:--, Use numbered button 0-9 to enter clock time then press Time set button again to complete time setting.
a. alarm by buzzer Press and release buzzer alarm button, display will flash the last alarm time set and buzzer alarm icon. Press the numeric buttons to set the alarm time then press ENTER button to complete buzzer alarm time setting. Display will show buzzer alarm icon and back to the real time status after a few seconds. To cancel the buzzer alarm setting, press and hold buzzer alarm button until a beep sounds. Display buzzer alarm icon will disappear and buzzer alarm setting is then cancelled.
Snooze When the alarm is on, press any buttons except POWER button to be in Snooze function for an interval of 5 minutes before pressing POWER button to turn it off. Display will flash Snooze and alarm icons. Setting the sleep timer Sleep timer allows the listener to set radio auto-shut off time from 120 to 15 minutes. Press and hold Power/ sleep timer button, display will flash sleep timer icon and cycle through 120 to 15 minutes. Release the button when desired shut off time is reached.
Note: FM frequency coverage varies from different market. MW (AM) 520-1710 kHz 522-1710 kHz Internal bar antenna Rotate for best reception SW 2.3-26.10 MHz Telescopic Fully extend the aerial for best reception Tune the radio There are five tuning methods for this radio. 1. ATS-Auto Tuning System This system automatically scan and preset the received stations in the order of signal strength,.i.e. best reception station will be preset at Preset 1 of PAGE A and so on.
There are 4 pages of preset memory each FM and MW band and each page covers 9 preset stations. When the ATS is completed, a beep will sound and radio will stop at strongest station within your area, To recall the preset station, press the PAGE button to allocate Page A to D, then press the preset numeric button. 2. Direct Tuning using the numerical key pad (0-9) If you know the radio station frequency, select required MW, FM or SW band by pressing BAND button then press FREQ button, display will show--.
Turn on the radio and select a waveband by pressing BAND button. Press and hold either the Tuning UP or Down buttons for more than half a second to commence scan tuning. The radio will scan the station frequency and stop automatically each time if finds an active station. When the waveband end is reached, the radio will beep and continue tuning from the opposite waveband end. 5. Memory recall stations You can store up to 108 preset station, 36 preset each on MW/FM/SW band.
Note: the original memory preset will be overwritten by the new station if the selected preset already stored a station. GB e. To recall a station in memory, turn on the radio and select a waveband by pressing BAND button. Press PAGE button to select stored page then the numeric button 1-9 corresponding to the preset memory. The radio will instantly tune to the station and display will show its frequency and memory location. f .
Select Shortwave meter band-shortwave scan tuning In order to shorten shortwave scan tuning time, you can select shortwave meter band. You can refer to below shortwave meter band range. SHORT WAVE BAND 120m 90 m 75 m 60 m 49 m 41 m 31 m 25 m 21 m 19 m 16 m 15 m 13 m 11 m FREQUENCY (MHz) 2.300 – 2.495 3.200 – 3.400 3.900 – 4.000 4.750 – 5.060 5.900 – 6.200 7.100 – 7.350 9.400 – 9.990 11.600 – 12.100 13.500 – 13.870 15.100 – 15.800 17.480 – 17.900 18.900 – 19.020 21.450 – 21.750 25.600 – 26.
Menu operation Through the Menu setting, you can adjust tuning settings to achieve tuning ways that you like under different circumstances for best performance. Squelch This is normal that background noise or static presents to some degree at different locations. It is best to set the squelch level as low as possible in order not to miss the weak transmissions. Squelch can be set either radio is on or off.
Tuning Mute (T. MUTE) If you prefer to mute the scan noise, you can select Tuning Mute. The initial Tuning Mute is ON for all bands. However for listeners who prefer not to miss any weak transmissions during the tuning, you can disable tuning mute function. Tuning Mute can be set either radio is ON or OFF. Press and hold Menu button until a beep sounds and display Menu icon appears. Press Tuning Mute button 2, display will first shows ON.
Change MW (AM) tuning step-9K/10K In Europe and most other parts of the world, MW (AM) tuning step is 9kHz. In Northern and Latin America, MW (AM) tuning step is 10 kHz. GB MW (AM) tuning step can be set either radio is ON or OFF. Press and hold Menu button until a beep sounds and display Menu icon appears. Press 9k/10k button, display will appear MW and flash 9 (kHz) or 10 (kHz) for Northern American version.
Set the AGC (auto gain control) In AM band (MW and SW), if the volume level changes too rapidly during listening, you can delay the responding by setting AGC IF (intermediate frequency) gain 1. AGC is for AM (MW/SW) only 2. AGC function is set the IF(intermediate frequency) gain, it has 3 selection by 50db/auto/30db 2-1 "Auto" selection is the defaulted AGC level which has a balanced gain for reception, recommended set on auto for general purpose.
Auto clock time adjustment by RDS-CT You can enable auto clock time adjustment by RDS (Radio Data System) CT function. Clock time can be automatically adjusted by FM RDS station. Note: RDS function is mostly available in European countries and part of Northern America area. To enable or disable RDS-CT function, Either radio is ON or OFF, press and hold Menu button until a beep sounds and display Menu icon appears. Press CT button 7, display will show OFF (disable CT function).
12/24 hour format To set 12/24 hour format, either radio is ON or Off, press and hold Menu button until a beep sound and display Menu icon appears. Press 12/24H button to cycle through 12 and 24 Hour format, press ENTER button to complete 12 or 24 hour format setting. Display illumination time Press LIGHT button to switch on and off display illumination. The radio can set display illumination time after last operation for convenience and battery power saving.
Bandwidth selection (B-W) 1. Narrow bandwidth can get lower noise and higher sensitivity while wide bandwidth can bet better frequency response under stronger RF signal. 2. The filtering bandwidths are listed on below table. While receiving FM RDS station, the bandwidth will be automatically adjusted to wide bandwidth Bandwidth Wide Normal Narrow FM 110k x 85k SW 4k 2k 1k MW (AM) 6k 3k 1.8k 3.
Fine Tune When radio is on, waveband is selected. Press FINE TUNE button to allow 1 kHz tuning step for MW/SW wavebands and 10 kHz for FM band, display will appear FINE TUNE. Press FINE TUNE button again to cancel fine tune setting, display FINE TUNE will disappear and radio will be back to normal tuning step. Tone control (News/Normal/Music) You may adjust tone performance according to radio program you are listening.
Headphones Headphones for use with this radio should be stereo and fitted with a 3.5mm stereo jack plug. Insert the headphone plug into the socket marked on the left hand side of the radio. When the headphones are plugged in, the loudspeaker is automatically disconnected. GB Note: before inserting the headphone, make sure radio volume is set to minimum to avoid damage to the ears. IMPORTANT: Excessive sound pressure from earphones and headphones can cause hearing loss.
RESET/Trouble shooting If the radio fails to operate correctly or some digits on the display are missing or incomplete, carry out the following procedures. 1. Remove the batteries from battery compartment. 2. With the aid of a suitable implement (e.g. the end of a paper clip or pen), press and hold the reset button located in the battery compartment for a few seconds. Specification Frequency coverage FM: 87.50-108 MHz or 76-108 MHz or 76-90 MHz or 64-108 MHz varies from market.
Output power: Speaker: DC-IN-1.5 Watt Battery: 1 Watt GB Headphone: 3 mW + 3 mW, stereo Charging current: 500 mA +/-100 mA Dimension (W x H x D): 165 x 100 x 34 in mm. Weight: approx. 375 g. The company reserves the right to amend the specification without notice. If at any time in the future you should need to dispose of this product please note that: Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
