DT-160 GB Version 1
Controls Earphone jack Memory button 1/Time setting button 3 Memory button 2/STEP button 4 Memory button 3 5 Memory button 4/Mono/Stereo button 6 Memory button 5/DBB button 7 POWER/BAND button 8 LCD display 9 TUNE/SET jog wheel 10 Strap holder 11 Volume button 12 Lock switch 13 Battery compartment 1 2 GB Display A B C D E F G H I J K Selected band Battery power indicator Signal level indicator FM stereo indicator 90 minutes auto shut off Key lock function Memory presets SET indicator DBB indicator NARR i
Battery Installation The Battery cover is located on the back of the unit. Slide the cover downwards to gain access to the battery compartment. Insert two AA (UM-3) batteries into the compartment. Make sure that the battery is positioned in accordance with the indicated diagram. Replace cover. Press and release the POWER/BAND button will turn on the radio.Press and hold the POWER/BAND button until “off” symbol appears on the LCD display. The radio will turn off. Note: 1.
Antenna/Earphone Insert the earphone into the earphone jack. The cord connecting the earphone to the receiver acts as an antenna during FM audio reception and should be extended as much as possible to increase the sensitivity. A built-in ferrite bar antenna is provided for AM reception, it is only necessary to rotate the radio for maximum signal strength during AM listening. Note: To prevent possible hearing damage, do not listen at high volume levels for long periods.
AM/FM Bandwidth narrowing In order to obtain better reception of weaker AM/FM stations, your radio has a function to narrow the AM/FM bandwidth to reduce high frequency noise. 1. Select the AM or FM band by pressing the POWER/BAND button. 2. Press in the jog wheel, the “SET” symbol will appear on the LCD display. Press Volume up button, display will appear “NARR” symbol to enter the auto bandwidth narrowing adjustment for improved sound quality.
Scan Tuning Turn on the radio, select the required band by pressing the POWER/BAND button. Turn and hold the jog wheel up/down for more than half a second and release the jog wheel to commence Scan Tuning. The radio will scan and stop automatically when a station is found. Manual Tuning Turn on the radio, select the desired band by pressing the POWER/BAND button. Desired station may be selected by turning the jog wheel up/down repeatedly until the desired station is reached.
Recall memory stations Turn on the radio, select the required band, then simply press and release the Memory station button. The LCD display will show the Memory preset and radio frequency. Stereo/Mono switch The radio is designed to receive FM stereo broadcastings. For weak FM signal, press in the jog wheel, the “SET” symbol will appear on the LCD display. Then press MO/ST button to switch Stereo/Mono to Mono position. The LCD display Stereo icon will disappear.
Software version The software display cannot be altered and is just for your reference. 1. Press in the jog wheel, the “SET” symbol will appear on the LCD display. Press and hold the STEP button when your radio is in power off mode, the screen will show the software version (e.g. A03). 2. Continue pressing and holding the STEP button and the radio will enter FM/AM step setting. FM/AM step setting 3. The screen will show FM tuning step (i.e. FM1 50 or 100).
Key Lock Function The key lock function is used to prevent unintentional operation of the radio. The Key Lock switch is located on the rear of the radio. When the key lock is set to LOCK, every button will be disabled and a key lock icon will appear on the screen. To disable the key lock function, switch the key lock button to the off position. The key lock function will be disabled.
Specification Battery: 2 X AA (UM-3/LR6) GB Frequency Coverage: FM: 87.50-108 MHz AM: 522-1710 kHz (9kHz) 520-1710 kHz (10kHz) Output Power: 1.0 mW+ 1.0 mW Earphone Jack: 3.5 mm diameter (stereo) Sangean reserves the right to amend the specifications without notice. If at any time in the future you should need to dispose of this product please note that: Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.